Avaya DMM build 1.00 Release Notes

DMM build 1.0.0

Date: November 10, 2009

DMM Release Notes

CONTENT HISTORY
October 8, 2009
0.14
See CR list, updated Wizard, VM msg transfer, skillset support
October 15, 2009 October 22, 2009 October 29, 2009
November 3, 2009 November 10, 2009 November 20, 2009
November 26,2009
0.15
0.16
0.17
0.18
0.19
0.20
1.0.0
See CR List See CR List See CR List See CR List; NOTE: Data must be re-imported See CR List; NOTE: Data must be re-imported See CR List; NOTE: Data must be re-imported See CR List; NOTE: Data must be re-imported

Build Content Overview

Build 1.0.0 contains fixes for:
CR Title
DMM showed alarm for failing to retrieve data of DNs as
Q02087356
Q02094930 Q02094951 DMM help button to include user guide doc Q02094872
Q02094915
Q02094940
export
The user should be able to choose to import/export voicemail messages
DMM Model needs to have a version attribute
Summarize contiguous warnings which occur across a range
DMM option to save configuration as an excel report
type Forecast fix
Nortel Page 1 of 4
Open CRs:
CR Title
DMM does not export voicemail msgs, without EM
Q02057445 Q02066058 Q02067868 Q02067869 Q02067870 Q02067137 Q02081622
Q02073098
keycode
DMM Internal system CDR not migrated DMM internal Diagnostic settings defaulted DMM Internal CAP assignment not Exported Scheduled archlogs and Backup not Exported DMM can not stop import when connection is lost DMM – Doorphone target DN not set
Apply can run without full Data Prep being done E
type Forecast fix E Not in this
release
E Not in this
release
E Not in this
release
E Not in this
release
E Not in this
release
E Not in this
release
E Not in this
release Not In This Release
Other Notes
DMM Testing Tip
For anyone that is running multiple DMM tests (i.e. multiple times performing an extract and/or apply), please reboot your BCMs (BCM4.0 and BCM5.0) between tests since we have found some anomalies when consecutive tests were performed when a reboot was not done.
Please ensure that the target BCM450 has the appropriate keycode allotment. Errors will be reported if the BCM450 rejects data due to keycode status for any application.
Open Call Pilot issues:
1. If the line no longer exist or valid in BCM 5.0, the AA line administration will fail for
that line. There is currently no work around.
2. BCM 4.0 bug missing DNS in voicemail. This may show that IP migration has not tested
DNS migration.
Constraints:
Data import and export operations are out of service operations that require
occasional reboots. The reboot operation is invoked by the tool, no user intervention required.
Data import and export operations place a heavy CPU load on the BCM, no Element
Manager connections should be active to the BCM
Keycode files for the destination BCM 450 Release 5.0 system need to be installed.
The Unified Messaging keycode is required to perform Voice Mail message migration.
All MBMs should be installed on the BCM450 prior to performing the export operation
Nortel Page 2 of 4
Keycode should be installed on the BCM450 prior to performing the export operation No FEM migration – too many combinations of cards and modules that the odds for
error/failure is high
Any MBM sitting in offset 3 (slot 4) on 4.0 can not be directly migrated to 5.0. It will
need to be post-DMM configured by being pulled, DIPs changed, and then re­inserted and Configured
IP trunks to be configured + other physical trunks > 150 then a best fit algorithm will
be used
No IVR data Call Forward All attributes (for Sets) can only be migrated if the Sets are booted on
the BCM450
When BRI modules share a bus with Loop type module (GATM, CTM, DID, etc.) in
the BCM 4.0 system, the user will be required to manually add either the BRI module or the loop-type module during the Configure MBM phase of the Data Preparation Wizard. The user must also indicate the bus and offset to DMM before the data can be properly migrated.
NEW FUNCTIONALITY
Version 1.0.0 of DMM introduces the ability to save data to an Excel file in addition to the existing XCM file. To use this capability, press the following icon:
Or Select File/Create Excel Report in the Menu The user is prompted to supply a file name to save the report to.
An Excel report cannot be sourced into the tool.
to save their data in a spreadsheet format.
This feature is designed to allow users
Software Version:
DMM Release 5.0 version

DMM:

S/W Distribution sites: Livelink:
http://livelink2.ca.nortel.com/livelink/livelink.exe?func=ll&objId=44418374&objAction=browse&sort=na me&viewType=1
The load is also available via the Application Launcher. Use the following url:
1.0.0
Nortel Page 3 of 4
http://bcm.sipsw.com/ApplicationLauncher
Select “Data Migration Manager” in the Applications area and press the “Run” button
DMM Bulletin Board:
http://bcm.sipsw.com/
Smoke test results:
See Livelink Folders
Nortel Page 4 of 4
Loading...