Autopage RS-725LCD Operation Manual

RS-725LCD

PROFESSIONAL REMOTE CAR STARTER

WITH ALARM SYSTEM

2-WAY LCD COMMUNICATION

OPERATION MANUAL

THIS PRODUCT IS DESIGNED FOR PROFESIONAL INSTALLATION ONLY

TABLE OF CONTENTS:

LCD REMOTE TRANSMITTER:

A BATTERY REPLACEMENT

B THE REMOTE LCD ICONS WITH FUNCTION

C PROGRAMMING OF THE LCD REMOTE TRANSMITTER

1. Screen Lamp ON

2. Power Save Mode

3. Clear The Flash Icon and Melody Sound

4. Stop The Melody Sound.

5. Button Lock

6. Vibration / Melody Mode

7. Enable / Disable Bi Sound While Pressing Button:

8. Low Battery Indication.

9. Set Up Fixed Count Down Timer

10. Out Of The Range Check

7 7 7 7 7 8 8 8 8 8

D CLOCK & TIMER SETTING

1. Clock Setting.

2. Alert Alarm Timer Setting

3. Count Down Timer Setting

4. Time Set-Up For “Daily Timer Start”

9 9 9 10 10

REMOTE TRANSMITTER OPERATION A. REMOTE TRANSMITTER OPERATION

B LCD DISPLAY TRANSMITTER OPERATION

C LED DISPLAY

D CHIRP INDICATOR

E PARKING LIGHT

F ALARM OPERATION CONDITION

G ACTIVE ARMING – ARM & LOCK

Defective Sensor Reminder Silent Arming / Disarming Shock Sensor By-Pass Hidden Alarm Function

12 12 12 12 12

H PASSIVE ARMING

Passive Arming with Passive Door Locking Passive Arming By-Pass

12 12 12

I ACTIVE DISARMING – UNLOCK & DISARM

Tamper Disarming Pathway Illumination Two Steps Door Unlock Automatic Re-Arm

13 13 13 13 13

J DISARMING WITHOUT A TRANSMITTER

Overrides the Alarm without Password Pin Code Overrides the Alarm With Password Pin Code

13 13 14

K VALET MODE

Enter Valet Mode Exit Valet Mode

14 14 14

L CAR LOCATOR

M PANIC FUNCTION

N TRIGGER THE SYSTEM

Clear The Trigger Icons and Melody Sound Stop The Melody Sound Only

15 15 15

Noise Abatement Circuit

O ANTI CAR- JACKING

Active Anti Car Jacking Passive Anti Car Jacking Trigger The Anti Car Jacking Mode Override The System To Turn Off Anti Car Jacking

16 16 16 16 16

P SYSTEM’S TRIGGER CHECK

Q SYSTEM’S STATUS CHECK

R DRIVER PAGING (OPTION)

S DOME LIGHT CONVENIENCE DELAY & SUPERVISION

T IGNITION CONTROL THE DOOR LOCK/UNLOCK

U TRUNK RELEASE (CHANNEL 3) OUTPUT

V CHANNEL 4 TIMER CONTROL OUTPUT

W POWER ON MEMORY

X SECOND VEHICLE SECURITY SYSTEM OPERATION

Programming 2nd car transmitter For Standard Remote Transmitter For 2-Way LCD Display Transmitter

18 18 18 18

REMOTE START OPERATION:

A TO REMOTE START THE VEHICLE

Safe Start (Child safety mode)

B TO OPERATE VEHICLE WHILE RUNNING ON REMOTE START

C TEMPORARY STOP FEATURE

D TURBO CHARGE MODE

E TIMER / TEMPERATURE START

3 (2) Hours Timer Start With Temperature-Control Off 3 (2) Hours Timer Start With Temperature-Control Daily Timer Start Exit the Timer Start

20 20 20 20 20

F TEMPERATURE CHECK

G TO TURN OFF THE REMOTE START

H SHUT-DOWN INPUT FOR REMOTE STARTER

I DISABLING THE REMOTE START SYSTEM

Congratulations on your purchase of the RS725LCD remote start vehicle security system. We sincerely hope the purchase of the RS725 remote start security system gives peace of mind to you.

The RS725 LCD is a state-of-the-art two-way communication system. Please take the time to read over this manual to thoroughly familiarize your self with the many features and options of the RS725.

Auto Page, Inc. has over 25 years of experience in the vehicle security industry in the United States and is a wholly owned subsidiary of Iwata Electric Co., of Tokyo, Japan. Iwata has been an industry leader for over 50 years, establishing a reputation for ingenuity in its engineering capability and innovative communication products. Auto Page and Iwata maintain a long tradition of providing the best value to their customers.

TRANSMITTERS

The RS725 comes with two transmitters. The XT72LCD is a 2-way transmitter and receiver, also referred to as a transceiver. The XT-33 is a mini-size 1-way transmitter. Both operate on the AM band with a code-rolling feature that will prevent any illegal use of a code-grabber attempting to record and steal the codes of your transmitter.

CHANGING THE BATTERY IN YOUR TRANSMITTERS XT72LCD: This transmitter uses a standard 1.5-volt AAA battery. Information on

changing the battery can be found on page 12 of this manual. XT-33: This transmitter uses two (2) 3-volt lithium ion batteries (#CR2016) that are

sandwiched together with the (+) side facing upward. To replace the battery, you will need to use a small flat blade screwdriver. Locate the small notch on the lower right side of the transmitter case next to the key ring. Using the flat blade screwdriver, carefully pry the top case from the bottom case. It should snap apart after breaking the seal. Before removing the batteries note the direction of the positive (+) terminal. Place the new batteries in exactly the same manner, being careful not to bend or damage the contact terminal. Snap the cases back together and then test the transmitter to insure it arms and disarms the alarm.

(2) CR2016

3-Volt Batteries

XT-33

WARNINGS:

As with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of.

1. Keep the transmitter out of children’s reach.

2. Do not leave anyone in the vehicle while running on remote control.

3. Alert servicing personnel that the vehicle can be started automatically.

4. Do not start the vehicle by remote while it’s in an enclosed area or garage.

5. Always apply the parking brake and lock the vehicle as you exit the vehicle.

6. The vehicle windows must be rolled up.

7. Should the unit malfunction, disconnect the fuse until the problem is corrected.

8. The use and operations of this system is the sole responsibility of the operator.

9. Some areas may have local ordinances that prohibit leaving a vehicle running on public streets.

10.Do not start the vehicle by remote while the standard transmission vehicle is parked

at a steep place.

LCD REMOTE CONTROL TRANSMITTER:

Note: If the system is interfered by stronger radio

frequency around, sources of high voltage electric power or such Obstacles like tall buildings and so on, the transmission range may get shorter as the system uses low out put powered frequency.

A. BATTERY REPLACEMENT:

A 1.5V type AAA Alkaline battery powers the

Remote Transmitter. When the power of the battery weakens a icon shall be displayed on the LCD screen. When the old battery is replaced to new one, there will be beep sounds indicate the power is up and the clock on the LCD screen returns to AM12:00 after displaying all the icons.

Correct the time by pressing for 3

seconds before using (See Timer Setting).

Note : Press the button two times when the battery compartment is

empty, then insert the new battery

B. THE REMOTE LCD ICONS WITH FUNCTION:

Door Lock

Your vehicle doors are locked

Door Unlock

Your vehicle doors are

unlocked and the system is

Disarmed

Armed Mode Your vehicle is in armed mode

Valet Mode

All the function shall be temporarily on hold.

Remote Transmission

You are transmitting the signal to control unit

In – Range Indicator Your are within range of the remote control

Door Open Warning

Doors are illegally opened (Zone 3)

Trunk/Hood Trigger Trunk or Hood is illegally opened (Zone 2)

Shock Sensor Trigger

Trigger on Shock Sensor (Zone 4)

Warn Away trigger

Trigger on Shock Sensor (Zone 1)

Engine Starting

Your vehicle engine starting by remote control

Engine Running

Your vehicle's engine is running

Timer Control Start Start the Engine automatically at the same time next day or every 3-hour.

Temperature Monitor

Indoor temperature of your vehicle

Time Monitor

Alert Alarm

You have set morning call alarm

Count Down Timer

Reminder when time is up for parking

Power Save Mode

Save the battery power

Vibration Mode

Remote Control vibrates when the system is triggered

Button Lock

Disable the transmission function temporarily

Driver paging

Someone is paging you in front of your vehicle

Low Battery

You have to replace the battery of remote control.

C. PROGRAMMING OF THE LCD REMOTE TRANSMITTER:

Transmitter Button Description Operation

(1 second)

LCD screen lamp turns on for

5 seconds.

Press and hold for 1 second 1 melody sound to confirm enters.

(3 seconds)

Timer Programming Mode.

Press and hold for 3 seconds 2-melody sounds to confirm enter.

(5 seconds)

Power Save Mode

Press and hold for 5 seconds 1 melody sound to confirm enters

- -

Clear the Flash Icon and

Melody Sound on the LCD

Screen Transmitter

Press within 3 seconds

- (2-second)

Button Lock ( ) enable /

disable

Press within 3 seconds and Hold

button for 2 seconds

- (2-second)

Melody / Vibration ( ) Mode

Press within 3 seconds and Hold

button for 2 seconds

- (2-second)

Program Count Down Timer

( ) (10-Minute / 20M / 30 M

/1Hour /1.5H / 2.0H)

Press within 3 seconds cycling *leave the buttons starting count

down then flashes

- (2-second)

Enable / Disable Bi Sound (Bi)

While Pressing Button

Press within 3 seconds and Hold

button for 2 seconds

1. Screen Lamp ON: Press and hold the button one second, one melody will

sound and the LCD screen lamp will turn on for 5 seconds.

2. Power Save Mode: While in the power save mode, the

LCD remote transmitter uses “0” current to save the battery power.

Entry: Press & hold the button for 5 seconds, one

melody will sound and the icon on the LCD screen indicates entry of the “power save mode”.

Exit: Press any button of the LCD remote transmitter to

exit the “Power Save Mode”.

3. Clear the Flash Icon and Melody Sound: Pressing the button 3 times

within 3 seconds will clear the flash icon and the melody sound on the LCD screen transmitter.

4. Stop The Trigger Melody Sound: While triggering the alarm the LCD screen will

alert the user through a melody sound and a flashing trigger icon. Press any button on the LCD remote transmitter to stop melody sound only.

5. Button Lock: This is useful if you want to disable the

transmission function of the remote control temporarily to prevent from any inadvertent pressing of buttons by others. Press the button first, within 3 seconds press and hold

( ) button for 2 seconds to activate or cancel the button

lock function, the icon will displayed on the LCD screen to show the LCD remote transmitter is on “Button Lock”

6. Vibration / Melody Mode:

This is useful when you are in a noisy place and it is difficult to

hear the beep sound from the remote control. In this mode, the remote control vibrates itself if your security system is triggered.

Press the button first, within 3 seconds press and hold

( ) button for 2 seconds to select the mode of vibration or

melody, the icon will displayed

on the LCD screen to show

the LCD remote transmitter is on vibration mode.

7. Enable / Disable Bi Sound While Pressing Button:

It has a short “bi” sound while pressing the button of the LCD screen transmitter If you want mute the “bi” sound mute always while press button. Press the

button first, within 3 seconds press and hold the (Bi) button for 2 seconds to disable the “bi” sound.

8. Low Battery Indication:

When the power of the battery weakens, it has two short “bi” sound and flash icon while pressing the button of the LCD screen transmitter.

9. Set Up Fixed Count Down Timer:

1. Press the button first, within 3 seconds press and hold the ( ) button for

2 seconds, the LCD screen will show the icon and timer (i.e. 0:10),

2. Press the ( ) button again showing next order time on the screen (ie.0: 20),

press them again (ie.0: 30)…and so on.

3. After the timer is set the count down begins when the icon flashes

Note: 1.The count down period is fixed as 10 minutes, 20 minutes, 30 minutes, 1 hour, 1.5 hours and 2 hours maximum.

a. When the count down timer shows 0:00 it means to turn off the timer.

b. Press button for real time indication when the timer is counting down.

10. Out Of Range Indication:

The system will automatically check the range every 20 minutes after the unit is

armed.

1. If the user is within the range, the icon will display on the LCD screen.

2. If user is out of range, it has five short “bi” sounds and the icon will disappear on the LCD screen.

+ 16 hidden pages

Autopage RS-725LCD Operation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual