AutoPage RS-650 Plus Operation Manual

RS-650 Plus

PROFESSIONAL REMOTE CAR STARTER

&

3 CHANNEL ALARM SYSTEM

OPERATIONS MANUAL

THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY

SYSTEM OPERATIONS

A. 5-BUTTON TRANSMITTER OPERATION

Transmitter
Button

-

-

+

+

-

A. ACTIVE LOCK & ARM:

System Function Remark

Lock Doors & Arm System
Arm and Delete The Shock

Sensor
Car locator

Panic function
Unlock Doors & Disarm System

Two Steps Door Unlock & Disarm
System

Silent Arming / Disarming

3RD Channel (Auxiliary)

Channel 2 (Trunk)
Passive Arming By-Pass
Activate Remote Start

Turn Off The Remote Start

Press twice within 5 seconds.
System Arme d

Press and Hold for 3 seconds

Press twice within 3 seconds.
Press both buttons together.
Press both buttons together.

(Feature III-2 must be ‘ON’ 3rd
Ch)
Press and Hold for 2 seconds

Press twice while unit is Passive
Arming Or Re-Arming.

1. Press button on the transmitter..

2. The horn will chirp once and parking light will flash once indicating that
the system is now armed. The vehicle doors will lock upon arming when
interfaced with the security system.

SILENT ARMING / DISARMING: Press the + button on the

transmitter will arm or disarm your security system, No chirp sound will
be heard, arm / disarm confirmation will be through the vehicles parking
lights only.

DEFECTIVE SENSOR REMINDER: If the siren sounds 3 chirps, then

you have left a door, trunk, or hood lid ajar. (See Alarm Feature “I - 4

Programming)

SHOCK SENSOR / OPTIONAL SENSOR BY-PASS:

Press the button once: The siren chirps once, The system is armed.
Press the button a second time within 5 seconds: The siren chirps

twice, the Shock Sensor is now bypassed.
The sensor bypass feature is programmed to activate for one arming
cycle only. The security system will return to normal operation during
the next arming cycle.

B. PASSIVE ARMING

Active arming / disarming is controlling your security system via the
remote transmitter. This security system is equipped with an optional
Passive Arming feature, which allows the security system to arm 30
seconds after the last door is closed. Operation is as follows:

1. Turn the ignition to the “OFF” position and exit the vehicle.

2. After all entrances are closed, the security system LED will flash fast
for 30 seconds. If you re-open any door / hood / trunk, the security
system LED will stop flashing. It will begin flashing again once the
vehicle all entrances are closed.

After 30-second timer has elapsed, the security system will automatically
“ARM”. The siren will chirp [1] time and the parking lights will flash [1]
time.

PASSIVE ARMING WITH PASSIVE DOOR LOCKING

(See Alarm Feature “I - 2” Programming):

The vehicle doors will automatically lock after passive arming cycle
has been completed.
PASSIVE ARMING BY-PASS: While the LED is fast flashing for passive

arming or Automatic re-arm, Press the buttons twice, the security
will respond with [1] chirp and LED will turn “ON”. The security system

will remain in this temporary state for as long as you wish.
To exit passive by-pass, press the or button and the system will

return to normal status.

C. ACTIVE UNLOCK & DISARM:

1. Press button on the transmitter..

2. The horn will chirp twice and parking light will flash twice to indicating
that the security system is now disarmed. The vehicle doors will un­lock and dome light wills turns on for 30 seconds upon disarming when
interfaced with the security system.

TAMPER DISARMING: If the alarm was triggered in your absence, upon
disarming the system, the siren will chirp 4 times, the parking lights will
flash 3 times.

PATHWAY ILLUMINATION (See Alarm Feature “II - 4” Programming):

This feature turns the parking lights “ON” for 30 seconds upon a unlock
signal and for 10 seconds upon the lock signal.

TWO STEP DOOR UNLOCK (See Alarm Feature “III - 3”

Programming):This feature will independently unlock the driver’s door
only when disarming the security system. Pushing the button a sec-

ond time within 3 seconds will unlock the entire vehicle.

AUTOMATIC RE-ARM (See Alarm Feature “I - 3” Programming):

If this feature is selected, the security system will automatically re-arm
itself 60 seconds after disarming with remote transmitter. Automatic re­arm will cancel if any door is opened before the 60 seconds timer has
elapsed.

D. DISARMING WITHOUT A TRANSMITTER

The Override function may be used if the remote transmitter is lost or
inoperative.

1. Enter the vehicle and turn the ignition switch to ‘ON’ position.

2. Within 10 seconds push and release the valet switch
The alarm will enter the disarm mode. You can now start and operate
the vehicle normally.

E. VALET MODE: (System in Disarm or Valet mode)

The valet switch allows you to temporarily bypass all alarm functions,
eliminating the need to hand your transmitter to parking attendants or
garage mechanics. When the system is in valet mode, all alarm functions
and remote start functions are bypassed, however the remote panic fea­ture and remote door locks will remain operational. To use the valet mode,
the system must first be disarmed either by using your remote transmit­ter, or by operating the Manual override sequence.

Enter Valet Mode:

1. From the disarmed condition, turn the ignition to “ON” position.

2. Push and hold valet switch for 2 seconds until the LED turns on. The

LED will remain on as long as the system is in ‘valet mode’.

Exit Valet Mode:

1. Return to normal operation, turn ignition ‘on’.

Push and hold valet switch for 2 seconds, The LED will turns off
indicating the system has exited the valet mode.

F. PANIC FUNCTION:

The transmitter can be used as a remote panic switch to manually trig­ger the alarm in case emergency.

1. Press and hold the button for 3 second. The alarm will immediately

sound.

2. During panic mode, the normal function of this transmitter button will

be suspended. The and buttons can be used to lock and un­lock the doors (if the option is installed), however once the button is

pressed, the vehicle’s starter disable device, (where installed) will be
enable allowing the vehicle to start.

3. To stop the alarm, press and hold the or button on the
transmitter again for 3 seconds. Also if any transmitter button other

than the or button is pressed and released, the panic mode
will be turned off immediately.

4. If no buttons are pressed, the alarm will automatically stop after
60 seconds.

G. TRIGGER THE SYSTEM

When armed, your vehicle is protected as follows:

1. Light impacts will trigger the warn-away signal. A [3] long chirp from
siren/horn.

2. Heavy impacts / Doors open / Hood open / Trunk open / Turn on the
ignition key will all trigger the programmed sequence.

The starter disable relay (if installed) prevents the vehicle’s starter from
cranking. The siren, horn, parking lights, and dome light will turn on
alerting of an intrusion for 60 seconds. Then it will stop and automatic
reset and re-arm. If one of the sensors or detectors is still active, the
alarm system will sound a maximum of 3 times of 60 seconds cycles.

H. DOME LIGHT CONVENIENCE DELAY & SUPERVISION
(See Alarm Feature III – 2 Programming)

The alarm with a unique feature which will turn on your vehicle dome
light as following: (optional) Additional installation required.

1. Upon disarming, the interior lights will remain on for 30 seconds.

2. If the vehicle is intruded, the interior light will flash for the same duration
as the siren.

Note: Turning on the ignition switch or arming the alarm will turn off the
dome light.

I. IGNITION CONTROL DOOR LOCKS.

(See Alarm Feature II – 2 Programming).

If the vehicle’s door locks have been interfaced to the security system,
the system will automatically lock the vehicle’s doors when the ignition is
turned “ON” and /or unlock the vehicle’s doors when the ignition is turned
“OFF”.

J. TRUNK RELEASE

Press and hold the button on transmitter for two seconds to remote
control the trunk release or other electric devices.

K. CAR LOCATOR

Press the button while the system is armed to activate the car locator
function. The horn will chirp 6 times and the parking lights will flash 12
times so you may easily locate your car.

LED DISPLAY

1 or 3

2 or 4

LED Function LED Function
Off Disarmed 2 flashes...

Slow
Flash

Fast
Flash
On
(Solid)

Armed 3 flashes...
Passive Arming 4 flashes...

Valet Mode 5 flashes...

pause
pause

pause
pause

Zone 2: Trigger on Trunk/Hood

Zone 3: Trigger on Door Switch
Zone 4: Trigger on Optional

Sensor
Zone 5: Trigger on Ignition

Switch

CHIRP INDICATOR

PARKING LIGHTS

Chirp Function Parking light Function
1 chirp Arm 1 flash Arm
2 chirps Disarm 2 flashes Disarm
3 chirps Defective Reminder 3 flashes Disarm / Triggered
4 chirps Disarm / Triggered 12 flashes Car Locator
6 chirps Car Locator Constant On Under Remote

Start

ALARM OPERATING INDICATORS

Siren, Horn Parking Light LED Doors Starter Dome Light

1. Arming

2. Disarming

3. Trigger Alarming Flashes Slow

4. Panic Alarming Flashes Flashes

5.
Car Locator

Chirps

Chirps

6 Chirps 12 Flashes

1 Flash Slow

Flash

2 or 3 Flashes Fast

Flash

Flash

Locking Disable

Unlocking Turns on for

30-second

Disable Flashes

REMOTE START OPERATIONS

WARNINGS:

As with any product that performs automatic functions, there are certain
safety precautions that you must practice and be aware of.

1. Keep the transmitter out of children’s reach.

2. Do not leave anyone in the vehicle while running on remote control.

3. Alert servicing personnel that the vehicle can be started automatically.

4. Do not start the vehicle by remote while it’s in an enclosed area or ga­rage.

5. Always apply the parking brake and lock the vehicle as you exit the
vehicle.

6. Should the unit malfunction, disconnect the fuse until the problem is
corrected.

7. The use and operations of this system is the sole responsibility of the
operator.

8. Some areas may have local ordinances that prohibit leaving a vehicle
running on public streets.

A. TO REMOTE START THE VEHICLE:

When you want to start your vehicle,

1. Press button on the transmitter..

2. The parking light will activate to indicate the remote start received the

signal.

3. The engine will start in approximately 5 seconds.

4. Once the engine is running, after a couple of seconds the parking

lights will turn on again and the climate controls will be activated ad­justing the vehicle’s interior temperature to your preset setting.

5. The vehicle will run for 5, 10, 20 or 30 minute programmable cycles

and then automatically shut down.
NOTE:
The Remote Start Unit will not start the vehicle if any one of the following
conditions exists:

1. The hood is opened.

2. The brake pedal is pressed.

3. The optional remote start enable toggle switch is moved to the OFF

position. (If installed)

4. The gear selector is in any gear other then “PARK” or “NEUTRAL”

(SAFTEY START OPERATION:)

The saftey start feature allows you to press the button 2 times before the
vehicle will remote start or remote shut down. (See Start Feature I-5)

B. TO TURN OFF THE REMOTE START:

When the engine is running (by remote start), if you want to stop it,

1. Press button on the transmitter..

2. Move the optional remote start enable toggle switch to the OFF
position. (If installed)

3. Press the brake pedal
The vehicle will shut down and turn off the parking lights to indicate the
engine has stopped.

C. TO OPERATE THE VEHICLE WHILE RUNNING ON THE
REMOTE START:

To operate the vehicle while running with the remote start ON:

1. Insert the ignition key and turn it to “ON” (not the start) position.

2. Press the brake pedal.
Note: If the brake pedal is pressed before the key is in the ON position, the
engine will shut down.

D. TEMPORARY STOP FEATURE:

This feature allows the vehicle to remain running after the key has been
removed from the ignition. This feature is useful for occasions when you
wish to exit and lock the vehicle for short periods of time, but would like to
leave the motor running and the climate control on.

1. Before turning off the engine, press the button on the transmitter

and the LED indicator will flash 3
times to confirm enter.

2. Turn the ignition key to OFF position. (The engine will stay running.)

3. The engine will run until the pre-programmed time elapsed or shut-

down input is received.

E. TIMER START:

This unit can be programmed to start and run the engine every 3 hours.
The engine will run for the programmed run time and then shut down.
IMPORTANT: Timer Start should be used only in open areas; Never start
and run the vehicle in an enclosed space such as a garage or carport.
3 hours timer start: This feature is design for an extreme cold climate
usage. The system will auto start the vehicle every 3 hours, to prevent
engine freezing and hard to start. A MAXIMUM OF SIX CYCLES CAN
OCCUR.

ENTER STEPS:

1. Press the button to remote start the vehicle(Waiting for the Parking

Lights to stay on).

2. Immediately depress the button, then immediately,,

3. Depress and Hold down the button until the parking lights flash (3)

times and the siren or horn chirps (3) times.

The vehicle is now programmed to start every (3) hours.

4. Press the brake pedal to stop the vehicle running.

Exit the timer start:

Timer start can be exited manually as follows:

1. REPEAT the “ENTER STEPS” from above,

-OR-

2. Turn the ignition on. The LED and parking light will flash (4) times. The
horn chirps (4) times.

The vehicle is no longer programmed to start automatically.

F. SHUT-DOWN INPUT FOR REMOTE STARTER:

If any of the following conditions exist while the system is operating, the
engine will not start or will shut down immediately:

1. The hood is opened.

2. The brake pedal is pressed.

3. Move the optional remote start enable toggle switch to OFF position.
(If installed)

4. Engine is over-revved. {“Tachometer checking type” only}

5. The pre-programmed run time (5 /10 / 20 / 30 minutes) has elapsed.

6. Transmitter button is pressed.

7. The vehicle refused to start running after {3} unsuccessful attempts.

G. DISABLING THE REMOTE START SYSTEM: (If installed)

This feature allows your system’s remote start unit to be temporarily
disabled to prevent the vehicle from being remote started accidentally.
This feature is useful if the vehicle is being serviced or stored in an
enclosed area. To disable the remote start, move the optional remote
start enable toggle switch to the OFF position.

LIMITED LIFETIME WARRANTY PROVISIONS

( U.S. and Continental U.S. Only)

1. AutoPage, Inc. WARRANTS that this new unit has been thoroughly inspected and

tested at the factory prior to delivery. Your AutoPage equipment is guaranteed for
“life” to the original purchaser/user of the equipment under the following conditions:
If the product proves defective (according to AutoPage’s testing) within the first year,
the defective unit may be exchanged or repaired free of charge. “Proof of Purchase”
(dated sales receipt) must accompany all warranty returns; otherwise, your return
will be rejected and sent back. After one (1) year, the purchaser should ship the unit
prepaid to AutoPage with a money order in the amount of $20.00 to cover shipping
and handling charges. Note: The enclosed Warranty Card may be required to receive
warranty services.

2. This WARRANTY will be considered void if the equipment has been misused, ne-

glected, improperly serviced, altered, dropped or damaged by water, contrary to the
AutoPage OPERATIONS MANUAL. Or, if used with accessories not approved by
AutoPage, which may have contributed to the defect. See note below regarding

product installation.

3. The purchaser’s remedies under this WARRANTY shall be limited to the repair or

replacement of electronic components only. THE FOLLOWING IS NOT COV-
ERED: Damages or deterioration to cases, batteries, covers and cabinets; the cost of
repairs, replacement and labor of which shall be borne by the purchaser even if occur­ring during the WARRANTY period.

4. Any equipment or parts which are claimed to be defective under this WARRANTY

must be sent to the AutoPage Service center with “proof of purchase” at the purchaser’s
expense prior to such return, a Return Authorization Number should be obtained.
AutoPage will return the equipment, charges prepaid. Warranty Service can be pro­vided through the dealer where the equipment is originally purchased.

5. Any unexpired WARRANTY shall be applicable to equipment and parts in the pos-

session of the original purchaser only.

6. THIS WARRANTY IS IN LIEU OF ANY AND ALL OTHER WARRANTIES, EX-

PRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

7. AutoPage shall not be liable, under the foregoing WARRANTIES or otherwise, for:

Any personal injury of any kind to the purchaser, its employees or agents or anyone
else whomsoever resulting directly or indirectly from the use or presence of the equip­ment or parts; Consequential damages of any kind; any inability of the purchaser to
use the equipment.

This WARRANTY CARD is for your record. However, AutoPage reserves the right to
request you to submit this WARRANTY CARD which must have complete information to
receive warranty service. Please keep this card in a secured place.

IMPORTANT NOTE: Any damages to the alarm system resulting from an
installation performed by anyone other than a professional installation techni­cian authorized by a dealer of Auto Page will void the product’s warranty.

This WARRANTY CARD is for your record. However, AutoPage reserves the right to
request you to submit this WARRANTY CARD which must have complete information
to receive warranty service. Please keep this card in a secured place.

AUTOPAGE WARRANTY SERVICE CARD

Model: _______________

Serial # _______________

CUSTOMER TO COMPLETE DEALER TO COMPLETE
Mr/Mrs/Ms
_______________________________ ________________________________

Your Name (Please Print) Company Name
_______________________________ ________________________________

Address Dealer’s Address
_______________________________ ________________________________

City, State, Zip Code City, State, Zip Code
_______________________________ ________________________________

Telephone Number Dealer’s Telephone Number
_______________________________ ________________________________

Year / Make / Model of Vehicle Date of Installation / Purchase

________________________________
Dealer’s Signature

“Proof of Purchase” which includes the store name and date of purchase must
accompany all warranty returns.

It is the purchaser’s responsibility to keep this card for any future warranty service.

AutoPage Inc.

1815 West 205th Street

Torrance, CA 90501

310-618-2002

1815 W. 205th Street Suite #101 Torrance, CA 90501

Tel: [phone] or [phone]

www.autopageusa.com