Auto Page RS-1000 User Manual

RS-1000 OLED

PROFESSIONAL OLED 2-WAY 900 MHz. REMOTE CAR STARTER

& 6 CHANNEL ALARM SYSTEM

With

Built-in Temperature Sensor

And Serial Port Data Link

OPERATION MANUAL

Please register your product at:

www.autopageusa.com

THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY

RS1000 OP 1/07

OLED REMOTE TRANSCEIVER:

A. OLED REMOTE DISPLAY……………………………….…..…………………………………..…………………… 4

The Remote Transceiver, XT-100 OLED

B. CHARGING THE BATTERY ……….………………………………………………………………………….….. 4 C. MAIN PAGE …………………………………………………………………………………………………………… 5 D. SELECT THE TRANSCEIVER’S BUTTON CONFIGURATION …………………………………………. 6 E. SELECT THE TRANSCEIVER FEATURES …………………………………………..………………………. 6

P1-1: Enable / Disable Bi Sound While Pressing Button (7) P1-2: Button Lock Setting (7) P1-3: Melody / Vibration Mode (7) P1-4: Demo Mode (8) P2-1: Power Save Mode (8)

P2-2: Parking Meter Setting (8)

P2-3: “Light For OLED” Timer Setting (9) P3-1: Timer Setting (9) P3-2: Alert Alarm Timer Setting (9) P3-3: Count Down Timer Setting (10) P3-4: Daily Start Timer Setting (10) P4-1: Name of

P5-1: Name of Channel Setting (11) P6-1: Language Setting (11) P6-4: Set To Defaults (12)

Transceiver Setting (11)

TABLE OF CONTENTS:

A. REMOTE TRANSMITTER OPERATION ……………………………………….………………….………….….… 12 B. LED DISPLAY .……………..……………………………………………………………………….………………….. 12 C. CHIRP INDICATOR ..………..……………………………………………………………………………….…..……. 12 D. PARKING LIGHT …….……..…………………………………………………………………………..……….….…. 12 E. ACTIVE ARMING – ARM & LOCK .……………………………………………………………………….…………. 13

Ajar Warning Silent Arming Sensor By-Pass

Hidden Alarm Mode

F. PASSIVE ARMING .…………………………………………..…………………….………………………….….…… 13

Passive Arming with Passive Door Locking

Passive Arming By-Pass

G. ACTIVE DISARMING – UNLOCK & DISARM .…………………………………………………..…………………. 13

Silent Disarming Tamper Disarming Pathway Illumination Two Steps Door Unlock Automatic Re-Arm

H. DISARMING WITHOUT A TRANSMITTER .……………..…………………………………………………..…….... 14

Overrides the Alarm without Password Pin Code Overrides the Alarm with Password Pin Code

I. VALET MODE .……………..…………………………………………………………………….…………………..…... 14 J. CAR LOCATOR .……………………………………………………………………….……………………………...… 15 K. PANIC FUNCTION .……………………………………………………………………………..….……………….…... 15 L. TRIGGER THE SYSTEM .………………………………………..………………………..………….………….….….. 15

Stop The Melody Sound Noise Abatement Circuit

M. ANTI CAR- JACKING .…………………………………………………………………………………………….…….. 16

N. SYSTEM’S TRIGGER CHECK ……………………………………………………………….….….…………....……. 16

O. SYSTEM’S STATUS CHECK ……………………………………………………………..……….……………..……. 16 P. DRIVER PAGING / LOSE AND FOUND ………………………….…………..……………………...………………...17

Q. DOME LIGHT CONVENIENCE DELAY & SUPERVISION ……………………..………………….………..……....17

R. IGNITION CONTROL THE DOOR LOCK/UNLOCK. ………..………………….……………………………..…..….17 S. TRUNK RELEASE (CHANNEL 3) OUTPUT ………..……………………………………………….……………...….17 T. CHANNEL 4 / 5 / 6 TIMER CONTROL OUTPUT ………..……………………………………………….…………..17 U. MULTI-VEHICLE SECURITY OPREATION: ………..……………………………………………………………….…17 V. OUT OF RANGE INDICATION: ………..…………………………….….…………………………………………….…18 W. POWER ON MEMONRY. ………..……………………………………………………………….…….……………….. 18

REMOTE START OPERATION:

A. TO REMOTE START THE VEHICLE ………..……………………………………………………………..………….. 18 B. TO OPERATE THE VEHICLE WHILE RUNNING ON THE REMOTE START ………………………………..….. 18 C. TEMPORARY STOP FEATURE ……………………………………………….………………….…………………… 19 D. TURBO TIMER MODE ……………………..………………………………….……………….………...………..….… 19

RS1000 OP 1/07

E. TIMER START …………………………………………….…………….……………………….…..…………………… 19

3 (2 or 1) Hours Timer Start Daily Timer Start Cancel the Timer Start

F. TEMPERATURE CHECK …………….……………………………………………….…...……….…………….….… 20 G. TO TURN OFF THE REMOTE START ……………………………………………….….…….………………….….…20 H. SHUT-DOWN INPUT FOR REMOTE STARTER …………………………….……………………………..………… 20 I. DISABLING THE REMOTE START SYSTEM …………………………….……………………..……………….….… 20

TEST MODE …………………..…………….……………………………………………….…...……….………..…….…… 20 Warranty Information………………………………………………………………………………………………………….21

Congratulations on your purchase of the RS1000 OLED remote start vehicle security system. We sincerely hope the purchase of the RS1000 remote start security system gives you peace of mind.

The RS1000 LCD is a state-of-the-art two-way communication system. Please take the time to read over this manual to thoroughly familiarize yourself with the many features and options of the RS1000.

Auto Page, Inc. has over 25 years of experience in the vehicle security industry in the United States and is a wholly owned subsidiary of Iwata Electric Co., of Tokyo, Japan. Iwata has been an industry leader for over 50 years, establishing a reputation for ingenuity in its engineering capability and innovative communication products. Auto Page and Iwata maintain a long tradition of providing the best value to their customers.

WARNINGS:

As with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of.

1. Keep the transmitter out of children’s reach.

2. Do not leave anyone in the vehicle while running on remote control.

3. Alert servicing personnel that the vehicle can be started automatically.

4. Do not start the vehicle by remote while it’s in an enclosed area or garage.

5. Always apply the parking brake and lock the vehicle as you exit the vehicle.

6. The vehicle windows must be rolled up.

7. Should the unit malfunction, disconnect the fuse until the problem is corrected.

8. T he use and operations of this system is the sole responsibility of the operator.

9. Some areas may have local ordinances that prohibit leaving a vehicle running on public streets.

10. It is not safe to remote start the vehicle if the vehicle is parked on a steep incline.

RS1000 OP 1/07

REMOTE TRANSCEIVER (TX)

A. OLED DISPLAY

Name of Transmitter

Clock / Timer

Door Lock

Door Unlock

In – Range Indicator

Alarm Status

Temperature

Car Jacking

Bypass Shock Sensor (Zone 4)

Engine Running

Count Down Timer

Parking Timer

Timer Start

ntenna

Battery Level

Melody Mode Vibration Mode

Alert Alarm

OLED Display

Engine Running

Button

Button 3

Reset Hole

B. CHARGE THE BATTERY

The unit has a built-in 3.7V lithium polymer battery. If the OLED screen display low battery or the remote transceiver needs charging. Please use the included AC / USB charger to charge the battery. While the battery is charging, you can push the ” battery should be charged at least once a month under normal operation.

” button to check charging condition. The

icon is flashing, your

switch

button

switch

Button

RS1000 OP 1/07

AC Power Supply:

The remote transceiver equipped AC POWER SUPPLY / AC ADAPTOR (Output Voltage: 4.2VDC – 5.5VDC and with same USB plug), then you can charge the battery indoors.

This screen will be displayed while the battery of the Remote Transceiver is charging.

C. MAIN PAGE:

1. Press the

button, the screen will display the main page.

2. When an icon is flashing on the OLED screen, press the

button. The OLED screen will display the details of the flashing icon. The sequence of flashing icons is as follows: TRIGGERED / ENGINE RUNNING / COUNT DOWN TIMER / TIMER START / ALART TIMER conditions.

While the TRIGGERED icon is flashing.

Push the button to display the triggered area.

While the icon flashes

Push the button

While the icon flashes.

Push the button and the count down timer will be displayed.

While the icon flashes.

Push the start or temperature start, depending on which you have selected.

RS1000 OP 1/07

Press button 2 to stop the count down time.

button, the OLED screen will display individually i.e. daily start timer, timer

While the flashing.

icon is

Push the button, the alert alarm time will displayed.

Press button 2 to turn OFF the alert alarm timer.

D. SELECT THE TRANSCEIVER’S BUTTON CONFIGURATION:

1. Spin the jog shuttle up

Switch to select the transceiver button configuration. The OLED screen will

display the transceivers button configuration you would like to select.

2. Within 5 seconds, press buttons 1, 2, 3 or 4 to select the remote controls “button configuration”. Note: If 5 seconds of inactivity expired, or the

mode will exit.

button is pressed, the transceiver button configuration

Spin up the switch to page 1.

Spin up the switch to page 2.

Spin up the switch to page 3.

Spin up the switch to page 4.

Spin up the switch to page 5.

Spin up the switch to page 6.

Spin up the switch to return to the main page.

E. SELECT THE TRANSCEIVER FEATURES:

1. Spin the jog shuttle down

Switch to select the transceiver feature you need and the OLED screen

will display the features you have selected.

2. Press buttons 1, 2, 3 or 4 once within 3 seconds after making a selection and the OLED screen will change to the alternative display.

Note: If 5 seconds of inactivity expires or if the

mode will exit.

button is pressed, the transceiver features program

Spin down the switch to page 1.

Spin down the switch to page 2.

Spin down the switch to page 3.

Spin down the switch to page 4.

Spin down the switch to page 5.

Spin down the switch to page 6.

RS1000 OP 1/07

Spin down the switch to return to the main page.

E- P1- 1. “BUTTON BI” SETTING: Example: Set the “Button Bi Disable”.

The unit has a short “bi” sound while pressing the buttons of the remote transceiver

Spin down the switch to page 1.

Press button 1 and it will display the previous setting.

Press button 2 to change the setting.

Press the button and the setting is complete.

E- P1- 2. “BUTTON LOCK” SETTING: Example: Set the “Button Lock Enable”.

Spin down the switch to page 1.

Press button 2 and it will display the previous setting.

Press button 1 to change the setting.

Press the button and the setting is complete.

D- P1- 3. “MELODY / VIBRATION MODE” SETTING: Example: set the Vibration mode.

Spin down the switch to page 1.

Press button 3 and it will display the previous setting.

Press button 2 to change the setting.

Press the button and the setting is complete and the display on the OLED screen.

icon will

RS1000 OP 1/07

E- P1- 4. “DEMO MODE”: To display the units demo mode

Spin down the switch to page 1.

Press button 4 to start the Demo movie.

Demo movie playing.

Press any Button to exit.

E- P2- 1. “POWER SAVE” SETTING: Example set the “Power Save Enable”.

While in the power save mode, the LCD remote transceiver uses “0” current to save the battery power.

Spin down the switch to page 2.

Press button 1 and it will display the previous setting.

Press button 1 to change the setting.

Press the button and the setting is completed. You can disable power save mode in the same manner.

E- P2- 2. “PARKING METER” SETTING: Parking timer: Example set the “Parking Meter 30 min..

Note: When the “parking meter” expires, press any button to stop the beeper.

Spin down the switch to page 2.

Press button 2.

Press button 1 three times to set the parking timer to 30 minutes. This will toggle between 10/20 and 30 minutes.

Press the start the parking meter

and the flash on the main page.

button to

icon will

D- P2- 3. “LIGHTING FOR OLED” SETTINGS: Example: Set the ON time for the OLED display from

seconds to 3 seconds.

Spin down the switch to page 2.

Press button 4 and it will display the previous setting.

Press button 2 to change the setting.

Press the button and the setting is done.

RS1000 OP 1/07

+ 16 hidden pages