Car Locator
Panic Function
Trigger the Syst
System Status check
Driver Paging
Dome Light Su
Ignition Control Door Loc
Trunk Release Output
Channel 3 Auxiliary Co
Channel 4 Auxiliary Control
Channel 5 Auxiliary Control
Channel 6 Auxiliary Control
Second Vehicle Operation
LCD Remote Control
LCD Battery Replaceme12
LCD Icons 12
Programmi
Timer Setting
Autopage Warr
Exit Valet Mode
tery XT-65 Standard Transmitter
rs
shes
By-pass
y-pass
m
nsmitter
em
pervision
ng LCD Transmitter
anty
ks
ntrol
nt
3
3
4
5
5
5
5
6
6
7
8
8
8
9
0
1
10
10
10
10
10
10
11
11
11
12
13
15
17
2
Congratulations on your purchase of the RF-525LCD vehicle security system. We
sincerely hope the purchase of the RF-525 security system gives you peace of mind.
The RF-525 LCD is a state-of-the-art two-way communication system. Please take
the time to read over this manual to thoroughly familiarize your self with the many
features and options of the RF-525.
Auto Page, Inc. has over 27 years of experience in the vehicle security industry in the
United States and is a wholly owned subsidiary of Iwata Electric Co., of Tokyo, Japan.
Iwata has been an industry leader for over 50 years, establishing a reputation for
ingenuity in its engineering capability and innovative commu nication products. Auto
Page and Iwata maintain a long tradition of providing the best value to their
customers.
TRANSMITTERS
The RF-525 comes with two transmitters. The XT-72LCD is a 2-way transmitter and
receiver, also referred to as a transceiver. The XT-65 is a mini-size 1-way transmitter.
Both operate on the AM band with a code-rolling feature that will prevent any illegal
use of a code-grabber attempting to record and steal the codes of your transmitter.
CHANGING THE BATTERY IN YOUR TRANSMITTERS
XT72LCD: This transmitter uses a standard 1.5-volt AAA battery. Information on
changing the battery can be found on page 12 of this manual.
XT-65: This transmitter uses one 3-volt lithium ion batteries (#CR2032). To replace
the battery, you will need to use a small flat blade screwdriver. Remove the screw
and locate the small notch on the lower right side of the transmitter case next to the
key ring. Using the flat blade screwdriver, carefully pry the top case from the bottom
case. It should snap apart after breaking the seal. Before removing the batteries
note the direction of the positive (+) terminal. Place the new batteries in exactly the
same manner, being careful not to bend or damage the contact terminal . Snap the
cases back together and then test the transmitter to insure it arms and disarms the
alarm.
XT-65 Extended Range Sliding Cover remote
CR2032 3-Volt Battery
3
OPERATION:
REMOTE TRANSMITTER OPERATION:
Transmitter
Button
-
+
-
-
-
+
+
+
II.
System Function Remark
Lock Doors & Arm System
Panic function Press and Hold for 3 seconds.
Car Locator Under armed mode
Arm and Delete The 2 Stage Shock
Sensor.
Silent Arming / Disarming Ignition in "off" position.
Arm System and Hidden Alarm Press twice within 3 seconds.
Unlock Doors & Disarm System
Two Steps Door Unlock & Disarm Press twice within 3 seconds.
Trunk Release (Channel 2) Press and Hold for 2 seconds
Passive Arming By-pass While the system Disarmed.
Channel # 3 Auxiliary Output
Channel # 4 Auxiliary Output (4)
Channel # 5 Auxiliary Output (5)
Channel # 6 Auxiliary Output (6)
Shifting Code for 2nd Car Operation Standard Transmitter ONLY
Press twice within 3 seconds
LCD DISPLAY TRANSMITTER OPERATION ONLY:
Transmitter Button System Function Remark
- (C)
System’s Trigger Check Press within 3 seconds
- - (C) System’s Status Check Press within 3 seconds (1 second)LCD screen lamp turns on
for 5 seconds.
- -
- + (2 sec)
Clear the Flash Icon and
Melody Sound on the LCD
Screen Transmitter
Switching code for 2nd / 1st
Car Operation
Press and hold for 1 second
Press within 3 seconds
Press within 3 seconds
BUTTON LOCK:
4
This is useful if you want to disable the transmission function of the LCD remote
control to temporarily prevent from any inadvertent pressing of buttons by others.
The 2-way remote control transmitter:
Press the
hold the
button first, within 3 seconds press and
( ) button for 2 seconds to activate or cancel
the button lock function.
The
confirm that the LCD remote transmitter is in the “Button
Lock” mode
icon will be displayed on the LCD screen to
.
LED display:
LED Function LED Function
Off Disarmed Zone 1 / Warn-Away Trigger
Slow FlashArmed 2 flashes... pause Zone 2 / Trigger on Trunk/Hood
Fast Flash Passive Arming 3 flashes... pause Zone 3 / Trigger on Door Switch
On (Solid) Valet Mode 4 flashes... pause Zone 4 / Trigger on Shock Sensor
5 flashes... pause Zone 5 / Trigger on Ignition Switch
CHIRP INDICATORS: PARKING LIGHT:
Chirp Function Parking light Function
1 chirp Arm 1 flash Arm
2 chirps Disarm 2 flashes Disarm
3 chirps Defective Reminder 3 flashes Disarm / Triggered
4 chirps Disarm / Triggered 12 flashes Car Locator
6 chirps Car Locator
ALARM OPERATING CONDITION:
1. Arming
2. Disarming
3. Trigger Alarming Flashes
4. Panic Alarming Flashes Flashes
5. Car Locator 6 Chirps 12 Flashes Locking
Siren /
Horn
1 or 3
Chirps
2 or 4
Chirps
Parking
Light
1 Flash
2 or 3
Flashes
LED Doors Starter Dome Light
Slow
Flash
Unlocking Turns on for 30 -sec
Slow
Flash
Locking Disable
Disable Flashes
ACTIVE ARMING – LOCK & ARM:
5
1. Press button on the transmitter.
2. The siren will chirp once and parking light will flash once indicating that the
system is now armed. The vehicle door will lock upon arming when interfaced
with the security system.
System Arm
Door Ajar
Trunk / Hood Ajar
Clear The Flashing Icon:
Pressing the
3 times within 3 seconds
will clear the flash icon
on the LCD screen
transmitter.
button
AJAR WARNING: If the siren sounds 3 chirps, then you have left a door, or (optional)
trunk, and or hood lid ajar.
SILENT ARMING / DISARMING: Pressing the transmitter
and buttons at the
same time will arm or disarm your security system, No chirp sound will be heard, arm
/ disarm confirmation will be through the vehicles parking lights only.
SHOCK SENSOR BY-PASS: Press the
button on the transmitter two times within
3 seconds will arm the security system and by-pass the shock sensor. The system
will chirp one additional time to confirm the sensor bypass mode was activated. The
sensor bypass feature is programmed to activate for one arming cycle only. The
security system will return to normal operation during the next arming c ycle.
HIDDEN ALARM FUNCTION: Press the button first; within 3 seconds press the
button to activate the hidden alarm function. The security system will arm and with
“Hidden Alarm Function”. The siren / horn will be silenced even if the sensor is
triggered in the armed status.
PASSIVE ARMING ( Programmable )
Active arming / disarming is controlling your security system via the remote
transmitter. This security system is equipped with an optional Passive Arming feature,
which allows the security system to arm 30 seconds after the last door is closed.
Operation is as follows.
1. Turn the ignitio n to the “OFF” position and exit the vehicle.
2. After all entrances are closed, the security system LED will flash fast for 30
seconds. If you reopen any door / hood / trunk, the security system LED will stop
flashing. It will begin flashing again once the vehicle all entrances are closed.
3. After 30-second timer has elapsed, the security system will automatically “ARM”.
The siren will chirp [1] time and the parking lights will flash [1] time.
PASSIVE ARMING WITH PASSIVE DOOR LOCKING
:
6
Loading...
+ 14 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.