Auto Page RF-215 User Manual
THIS PRODUCT IS DESIGNED FOR PROFESIONAL INSTALLATION ONLY
RF-215
PROFESSIONAL VEHICLE SECURITY SYSTEM
OPERATION MANUAL
1
TRANSMITTER OPERATION
Transmitter Button System Function Remark
Button
– Button
Button
Button for 3 seconds
Button
– Button
Button for 2 seconds
+ Button
+ Button for 1 seconds
II
Arm / Lock door
Arm and Delete
Optional Sensor
Car Locator System in Armed.
Panic function Press 3 seconds
Disarm & Unlock
Door
Two Steps Door
Unlock & Disarm
System
Pop Trunk Release Press 2 seconds
Silent Arm / Disarm Ignition in "off"
Activate Car-Jacking
Switching code For
2nd Car Operation.
Press twice.
Press twice within 3
seconds.
position.
Ignition in "on"
position.
ACTIVE ARMING – LOCK & ARM:
1. Press button on transmitter.
2. The siren will chirp once and the parking lights will flash once indicating
that the system is now armed. The vehicle doors will lock upon arming
when interfaced with the security system.
Note: Defective sensor reminder: If the siren sounds 3 chirps, then you
have left a door, trunk, or hood lid ajar.
SILENT ARMING / DISARMING: Press the + button together on the
transmitter to arm or disarm your security system, No chirp sound will be
heard; arm / disarm confirmation will be through the vehicles parking lights
only.
SHOCK SENSOR / OPTIONAL SENSOR BY-PASS: Press the button
on the transmitter twice within 3 seconds will arm the security system, bypass the shock sensor. The system will chirp one additional time to confirm
the sensor bypass mode was activated. The sensor bypass feature is
programmed to activate for one arming cycle only. The security system will
return to normal operation during the next arming cycle
PASSIVE ARMING:
Active arming / disarming is controlling your security system via the remote
transmitter. This security system is equipped with an optional Passive
Arming feature, which allows the security system to arm 30 seconds after
the last door is closed. Operation is as follows.
1. Turn the ignition to the “OFF” position and exit the vehicle.
2. After all entrances are closed, the security system LED will flash fast
for 30 seconds. If you reopen any door / hood / trunk, the security
system LED will stop flashing. It will begin flashing again once all
vehicle entrances are closed.
2
3. After 30-second timer has elapsed, the security system will
automatically “ARM”. The siren will chirp [1] time and the parking lights
will flash [1] time.
PASSIVE DOOR LOCKING:
The vehicle doors will automatically lock after passive arming cycle has been
completed.
ACTIVE DISARMING – UNLOCK & DISARM:
1. Press the button on the transmitter.
2. The siren will chirp twice and parking lights will flash twice to indicate that
the security system is now disarmed. The vehicle doors will unlock and
disarm when interfaced with the security system.
TAMPER DISARMING: If the alarm is triggered; upon disarming the
system, the siren will chirp 4 times and parking lights will flash 3 times.
TWO STEP DOOR UNLOCK: This feature will independently unlock the
driver’s door only when disarming the security system. Pushing the
button on the transmitter a second time within 3 seconds will unlock the
entire vehicle.
AUTOMATIC RE-ARM: If this feature is selected, the security system will
automatically re-arm itself 60 seconds after disarming with remote
transmitter. Automatic rearm will cancel if any door is opened before the 60
seconds timer has elapsed.
DISARMING WITHOUT A TRANSMITTER
The Override function may be used if the remote transmitter is lost or
inoperative.
1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm
will sound.)
2. Within 10 seconds push and release the valet switch
The alarm will stop sounding and enter the disarm mode. You can now
start and operate the vehicle normally.
VALET MODE:
The valet switch allows you to temporarily bypass all alarm function,
eliminating the need to hand your transmitter to parking attendants or
garage mechanics. When the system is in valet mode, all alarm functions
are bypassed, however, the remote panic feature and remote door locks
will remain operational.
Enter Valet Mode:
1. Turn the ignition to “ON” position.
2. Push and hold valet switch for 2 seconds or until the LED turns on.
The LED will remain on as long as the system is in 'valet mode'.
Exit Valet Mode:
1. Return to normal operation, turn ignition 'ON'.
2. Push and hold valet switch for 2 seconds; the LED will turn off
indicating the system is exiting the valet mode.
PANIC FUNCTION:
The transmitter can be used as a remote panic switch to manually trigger
the alarm in case of emergency.
1. Press and hold the button on the transmitter for 3 seconds. The
alarm will immediately sound.
2. To stop the alarm, press and hold the button for 3 seconds on the
transmitter, the panic mode will be turned off immediately.
3. If the button is not pressed, the alarm will automatically stop after 30
seconds.
3
Loading...