Audiovox AS - 9151N User Manual

AS - 9151N

Remote Car Starter

Installation Instructions

For installation in vehicles with 12 volt negative ground circuits,

gasoline engines, with automatic transmission only!

KIT CONTENTS

(1) Remote Start Control Module
(2) Wiring Harnesses
(1) Parts Bag Containing

(2) Fuses
(2) Fuse Holders
(1) Control Switch

(1) Ring Terminal
(4) 1/2" Long Screws
(1) Pin Switch

(1) Hood Diode Bridge
(1) Literature Package
(1) RF Antenna Extender (AS-9166)

Form No. 128-4500B

The AS-9151N is for Automatic Transmission vehicles only! Although it is a sophisticated system, with multiple built-in
safety features, it must not be installed into vehicles with manual transmissions. Doing this can cause serious personal
injury and property damage.
IMPORTANT ! DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE 12 PIN INPUT / OUTPUT HARNESS
INTO THE REMOTE STARTCONTROL MODULE UNTIL ALL CONNECTIONS HAVE BEEN MADE TOTHE VEHICLE.

WIRING CONNECTIONS: 6 Pin Main Power Harness

1. RED w/ WHITE Tracer Wire:+12VDCBattery 1 Source

Connect this wire toa+12VDCconstant source. Using the 30 A fuse provided, connect this wire to the positive
terminal of the vehicle's battery.
The Battery 1 source provides + 12 volts to the AS-9151N module for Ignition 1 output, Ignition 2 output, and circuit
logic.

2.REDWire:+12VDCBattery 2 Source

Connect this wire toa+12VDCconstant source, but not the same source as the battery 1 wire, unless connecting
directly to the battery terminal. Using the 30 A fuse provided, connect this wire to the positive terminal of the vehicle's
battery.
The Battery 2 source provides + 12 volts to the AS-9151N module for Starter output and Accessory output.

3. YELLOW Wire : Starter Output

Connect this wire to the starter wire from the ignition switch harness. This wire will show +12 Volts when the ignition
key is turned to the “ START or CRANK “ position, and 0 Volts when the ignition key is in any other position.
NOTE: If installing the AS-9151N with an alarm that utilizes a starter cut relay, make sure the Yellow wire is connected

to the “ starter “ side of the relay contacts, and not the “ switch “ side.
When installing the AS-9151N into vehicles with a factory installed security system, connect the Yellow wire between
the output of the starter cut relay and the neutral safety switch.

4. BLUE Wire : Ignition 1 Output

Connect this wire to the ignition 1 wire from the ignition switch harness. This wire will show +12 Volts when the ignition
key is turned to the “ RUN or ON “ and the “ START or CRANK “ positions, and 0 Volts when the key is turned to
the “ OFF “ and “ ACCESSORY “ positions.

5. LIGHT GREEN Wire : Ignition 2 Output

Connect this wire to the ignition 2 wire from the ignition switch. This wire will show +12 Volts when the ignition key
is turned to the “ RUN or ON “ position, and in some cases, the “ START or CRANK “ position. This wire will show
0 Volts when the key is turned to the “ OFF “ and “ ACCESSORY “ positions.

NOTE: Some older vehicles may not require the second ignition wire.

6. VIOLET Wire : Accessory Output

Connect this wire to the accessory wire from the ignition switch. This wire will show +12 Volts when the ignition key
is turned to the “ ACCESSORY “ and “ RUN or ON “ positions, and 0 Volts when the key is turned to the “ OFF “ and
“ START or CRANK “ positions.

LT.BLUE WIRE
FROMAS-9151N





SEE"WIRING THE12PINCONNECTOR"­LT.BLUE WIREIF REQUIRED.

LT.GREENWIRE
FROMAS-9151N

VIOLETWIRE
FROMAS-9151N



WIRING THE 6 PIN MAIN POWER HARNESS

REDw/WHITETRACE
WIREFROMAS-9151N

RED WIRE
FROMAS-9151N





YELLOWWIRE
FROMAS-9151N

SPLICE (TYP.)



BATT 1

BATT 2

ACC

IGN 1

IGN 2

IGN 3

*

START

IGNITION SWITCH KEY POSITION

OFF ACCESSORY ON / RUN START




+12 VDC IN KEY POSITION INDICATED



MAY BE +12 VDC IN KEY POSITION INDICATED



THIS CIRCUIT IS NOT ALWAYS REQUIRED FOR INSTALLATION

*
























WIRING CONNECTIONS: 12 Pin Input / Output Harness

1. BLACK Wire: Chassis Ground Source

Connect this wire to a solid, clean chassis ground source.

2. DARK BLUE Wire: Remote Start Signal Input

Connect this wire to the pulsed ground output from the remote alarm system. In most cases, it will be connected to
the second or third channel output from the alarm. When the Dark Blue wire receives a ground pulse, the vehicle will
start.

3. BLACK w/WHITE Tracer Wire: Control Switch

The Black w/ White tracer wire provides ON-OFF control of the Remote Starter.

When the Black w/ White wire is switched to a fulltime ground, the AS-9151N Remote Start Module is operative. When
the Black w/ White wire is at open circuit through the control switch, the remote starter is disabled.

Connect the Black w/ White tracer wire to one of the terminals from the back of the control switch. Connect the
remaining terminal on the control switch to chassis ground. Always try to mount the switch so that the ON position
is in an upward direction.

4. GREY Wire: Negative Inhibit Input 1

Connect this wire to the existing hood pin switch from the alarm system, using the diode bridge included in the package.
Wire the diode bridge as shown in the illustration below. Any time the Grey wire is grounded, the Remote Starter will
stop operating, even if the signal is received from the alarm.

EXISTING HOOD PIN SWITCH

GREY WIRE FROM REMOTE
START HARNESS

RED BUTT
CONNECTOR

(2) IN4001

DIODES

DIODE BRIDGE ASSEMBLY

FEMALE BULLET TERMINAL

EXISTING ALARM
PIN SWITCH WIRE

MALE BULLET

IMPORTANT ! If the alarm system does not incorporate a hood pin switch, you must add a switch to the Remote Start

system. This is an important safety feature of the AS-9151N Remote Starter, and failure to use this feature can result in
serious injury.

5. GREY w/ BLACK Tracer Wire: Negative Inhibit Input 2

Any time the grey w/ black tracer wire is grounded, the Remote Starter will stop operating, even if the signal is received
from the alarm.
If the brake light switch in the vehicle switches ground to the brake light circuit, connect the Grey w/ Black trace wire
to the output of the brake light switch. If the brake light switch in the vehicle switches +12 Volts, do not use the Grey
w/ Black wire; see Brown w/ White tracer wire.

6. BROWN Wire: Positive Inhibit Input 1

Any time + 12 Volts is applied to the Brown wire, the Remote Starter will stop operating, even if the signal is received
from the alarm.
If the vehicle has a factory installed hood pin switch, and that switch provides + 12 Volts to an under hood light, the
Brown wire can be connected to the existing pin switch.

7. BROWN w/ BLACK Tracer Wire: Positive Inhibit Input 2

Any time + 12 Volts is applied to the Brown w/ Black tracer wire, the Remote Starter will stop operating, even if the signal
is received from the alarm. If the brake light switch in the vehicle switches + 12 Volts to the brake light circuit, connect
the Brown w/ Black trace wire to the output of the brake light switch. If the brake light switch in the vehicle switches
ground, do not use the Brown w/ Black wire; see Grey w/ Black tracer wire.