Audio Technica AT-705 Owners Manual
OWNER'S
MANUAL
Your
new
comfortable
adapter
AT705 stereo headphone consists
headphone
which
connects
and
a separate impedance
to
the
amplifier
system.
technical expertise
The
Technica, makers of the
cartridges, were
phone set
fully
featuring a wide-range
and
highly
exploited
manufacturing
acclaimed Dual
to
ural sound.
As
with
sible bi-polar, open- back
our other headphone models, the
phone. This design
which
transient
is a cause
improves
ing
construction
not
only
response
of
discomfort
reduces
and
eliminates the "closed- in" feel-
ai, closed-back headphone.
The convenient impedance
quire
a separate power source,
of
static
it
and possible damage
up
to
your stereo
amplifier
matching
thus
to
and
rience in superb music enjoyment.
of a lightweight,
output
skill
bring you
flat
this
excellent head-
response and clear,
functionally
was
applied
weight
and
when using the
adapter does
eliminating
the usual cause
the driver units.
you are ready
matching
of
your
of
Magnet
to
this
bulk
convention
Simply
for
an expe-
stereo
Audio-
phono
natsen-
head-
but
also
not
hook
-
re-
YOUR
The
fier
signed
either
fessional
AMPLIFIER
adapter
with
can
an
output
for
use
transistor
BTL
be
with
or
tube
connected
of
over 3
4 to
16-ohm
type
, or even a
to
any
watts
and
speakers,
model. Since the AT705 is a
CONNECTIONS
The connecting cords
coded as
follows:
Red
: R+
Black: R White:
Blue: L -
1.
After
switching
your amplifier, remove the speaker cords
the
terminals
as
illustrated
fier models the channel
marked
as
model where
into
using each
"0"
4-ohm,
"8
ohms" and the
or "
Common."
the
8-ohm
terminal
Generally speaking, the
through
tained
of
the adapter are color-
(right
channel)
(right
L +
and
below(Fig
ground)
(left
channel)
(left
ground)
off
the power
connect the adapter cords
. 1). In some
terminals
ground
In the
plus
terminals are separated
and
case
16-ohm,
and select the best one.
finest
effect is ob-
the 16-ohm terminal.
LEFT CHANNEL SPEAKER
supply
may
terminals
of a tube
test-listen
ampli-
de-
pro-
from
ampli-
highly
sensitive
should
be
low
distortion
should
be
of
the
amplifier,
2.
Next, connect
minals on the back
shown
in Fig.1 .
wires
loose
tighten
then
3.
If
of
be
your
er
terminals, simply
cords
to
tions
speaker
them
intact.
switch
the signal
4.
Finally, insert the headphone cord
into
the
jack
plug casing should face
petes
the necessary connections.
AMPLIFIER
SPEAKER
instrument
of
a comparable high
, your
and noise levels. The
connected to the speaker
not
the headphone terminals.
the
speaker cords to
of
the AT705
Be
sure
which
can cause
that
short
the screws.
amplifier
has an extra pair of speak-
connect the adapter
and leave the speaker connec-
Operating
of
to
the respective equipment.
of
the adapter. The dent in
the stereophone-
the adapter
upward
CHANNEL
TERMINALS
RIGHT
amplifier
quality
with
adapter
terminals
the
ter-
adapter
as
there are no
circuiting
input
will
channel
plug
the
. This
com-
SPEAKER
,
Fig.1
+
Loading...