AT&T ID501 User Manual

Download

Page 1

user’s manual

SoundPad

Model #: ID501

Music Dock for iPad®, iPhone® and iPod®

Page 2

Page Page

hello

What’s Included

AC Adapter

Docking Station

Battery

iPad/iPhone/iPod

Support Stand

2 3

Thank you for purchasing SoundPad [ ID501].

Music Dock for iPad®, iPhone® and iPod®

Features

· Speaker dock for iPad, iPhone and iPod

· FM radio

· Dual alarm clock

· Line-In Jack for use with other devices

· Play & charge your iPad, iPhone and iPod simultaneously

· Preset equalizer

· Sleep timer

· Full function remote

Unpack the docking station and make sure all accessories are put aside so they will not be lost.

iPad, iPhone and iPod are registered trademarks of Apple Inc.

Remote Control

(includes 3V CR2025

Lithium battery)

Page 3

Page Page

Contents

Introduction

What’s Included

Safety Information

Getting Started

Location of Controls Power Supply Back Up Batteries Preparation of Remote Control Compatibility

Operational Instructions

Setting the Digital Clock Alarm Functions Dimmer Function Electronic Volume Control Music Equalizer Radio Operation Operation with iPad, iPhone and iPod Using the Audio Line in Connection

Troubleshooting

Compliance with FCC Regulations

Specifications

Warranty Information

10 10 10 11

12 13 14 15 15 16

4 5

Safety Information

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO DRIPPING OR SPLASHING LIQUIDS.

NOTES: Caution symbols are printed on rear of docking station.

Please refer to user’s manual.

This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.

Warning!

The lightning flash and arrowhead symbol within the triangle is a warning sign alerting you of “dangerous voltage” inside the product.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

WARNING: To reduce the

risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicing to qualified service personnel.

The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product.

Page 4

Page Page 6 7

Safety Information Safety Information

Important Safety Instructions

1. CLEANING - Unplug the docking station from the wall outlet before cleaning. Clean the docking

station using a damp cloth; do not use liquid or aerosol cleaners.

2. ATTACHMENTS - Do not use attachments not recommended by the manufacturer.

3. ANTENNA - Do not connect an external antenna to the docking station (other than that provided).

4. WATER AND MOISTURE - The docking station should not be used near water. For example: near a

bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement.

5. PLACEMENT - Do not place the docking station on an unstable table, stand, tripod, or bracket. This

may result in serious personal injuries and damage to the docking station.

6. VENTILATION - The docking station should be situated so that its location or position does

not interfere with its proper ventilation. For example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings. Also, it should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow of air through the ventilation openings.

7. PERIODS OF NON-USE - If the docking station is to be left unused for an extended period of

time, such as a month or longer, the power cable should be unplugged from the docking station to prevent damage or corrosion.

8. OBJECTS AND LIQUID ENTRY - Care should be taken so that external objects do not fall into and

liquids are not spilled onto any openings or vents located on the product.

9. POWER SOURCE - The docking station should be connected to a power supply only of the type

described in the operating instructions or as marked on the docking station. If you are not sure, please consult the dealer or local power company.

10. POWER CORD PROTECTION - Power supply cord should be routed so that it is not likely to be

walked on or pinched by items placed upon or against it. It is always better to have a clear area from where the cable exits the docking station to where it is plugged into an AC outlet.

11. LIGHTNING - Unplug the docking station from the wall outlet and disconnect the antenna or cable

system during a lightning storm or when it is left unattended and unused for long periods of time. This will prevent damage to the product due to lightning and power-line surges.

12. OVERLOADING - Do not overload wall outlets, extension cords, or integral convenience receptacles

as this can result in a risk of fire or electric shock.

13. HEAT - The docking station should be situated away from heat sources such as radiators, heat

registers, stoves or other appliances (including amplifiers) that produce heat.

14. DAMAGE REQUIRING SERVICE - The docking station should be serviced by qualified service

personnel when:

A. the power supply cable or plug has been damaged. B. objects have fallen into or liquid has been spilled onto the enclosure. C. the docking station has been exposed to rain. D. the docking station has been dropped or the enclosure damaged. E. the docking station exhibits a marked change in performance or does not operate normally.

When used in the directed manner, SoundPad has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in this user’s manual and on the docking station.

15. SERVICING - The user should not attempt to service the docking station beyond those methods

described in the user’s manual. Opening or removing covers will expose you to dangerous voltage and other hazards. Service methods not covered in the user’s manual should be referred to qualified service personnel.

16. SAFETY CHECK - Upon completion of any service or repair to the docking station, ask the service

technician to perform safety checks to determine that the product is in proper working condition.

Page 5

Page Page

Location of Controls

Remote Controls

iPad/iPhone/iPod Rear Support Stand

1. Slot for iPad/iPhone/iPod rear support stand

2. iPad/iPhone/iPod Dock

3. iPad/iPhone/iPod rear support stand

4. DIMMER button

5. EQ/SLEEP button

6. DISPLAY/CLOCK Adj. button

7. ALARM button

8. FUNC. button

9. VOL. UP button

10. SNOOZE button

11. BACK/TUNE-/M- button

12. PLAY/PAUSE/FM MODE button

13. NEXT/TUNE+/M+ button

1. ON/STANDBY button

2. EQ/SLEEP button

3. FUNC. button

4. BACK/TUNE -/M- button

5. PLAY/PAUSE/FM MODE button

6. NEXT/TUNE +/M+ button

7. ALARM button

8. MEMORY button

9. Vol. UP + button

10. SNOOZE button

11. DISPLAY/CLOCK Adj. button

12. Vol. DOWN - button

13. Battery compartment

14. MEMORY button

15. VOL. DOWN button

16. Storage dock for remote control

17. ON/STANDBY Button

18. LCD display

19. Remote control sensor

20. Speakers (left/right)

21. Ambient lighting (bottom of docking station)

22. FM antenna wire

23. AUX-INPUT socket

24. DC jack (DC 12V + )

25. Back up battery compartment

(bottom of docking station)

Geing Started Geing Started

8 9

- iPad rear support stand can be adjusted by the “SCREW-CONTROL” which is located at the back of the rear support stand.

- Rotate the “SCREW-CONTROL” clock wise, to stretch out the rubber pad.

- To reverse the rubber pad backwards, simply rotate the “SCREW-CONTROL” counter clockwise.

- Gently insert the rear support stand into the cavity on the docking station after adjusting the rubber pad level as desired.

4 5 6 7 8 9

10 11 12 13 14 15

4~15 buttons

Rotate the screw-

control clock wise

Screw-control Rubber pad

Rubber pad Stretched out

Page 6

Page Page 10 11

Power Supply

Geing Started

AC Operation (External AC-DC Power Adaptor)

- SoundPad is equipped with a “DC-jack” that should only be used with the supplied ACadapter to operate the docking station. Use of other adaptors may damage the docking station or cause it to malfunction.

- Plug the tail end of the AC-adaptor into the DC-jack (socket) on the rear of the docking station.

- Insert the plug of the AC-adaptor into a wall outlet with AC-power not controlled by a wall switch.

- Press the button to switch on the docking station.

- SoundPad is designed to operate without ever being totally powered “OFF”.

It will either be “ON” or in “STANDBY” mode.

- In “STANDBY” mode, the blue back-light of the digital display will be dimmed but the display will show the current time (clock function).

- Anytime during standby mode, you can switch “ON” the docking station by pressing the button.

- Save energy by switching the system to “STANDBY” mode when not in use.

Back Up Batteries

- Open the battery door at the bottom of docking station.

- Insert one CR-2032 lithium cell battery (included) in the battery compartment.

- Please make sure the polarities match while inserting the batteries, or the back up memory will not function.

This battery is for backup of the “real time clock” and “radio memory preset stations

during brief power outages.

Preparation of Remote Control

- Gently pull out the plastic “tab” from the battery compartment at the rear of the remote control to activate operation of the battery inside the remote control.

- Test the remote control by pressing the button to check that the docking station switches on properly using the remote control.

- To replace the battery, please use one CR2025 lithium battery.

Compatibility

Geing Started

Page 7

Page Page

Alarm Function

Operational Instructions

Setting the Alarm

1. In standby mode, press and hold the ALARM button until the hour digits are flashing

and the docking station is displaying the Alarm 1 icon “ “

2. Press the or button to reach the hour of the desired wake up time. Press the ALARM button to confirm. The docking station should now have the minute digits flashing.

3. Press the or button to reach the minutes of the desired wake up time. Press the ALARM button to confirm. The docking station should now have the wake up source text flashing.

4. Press the or button to select the wake up source:

Buzzer, Radio or iPad/iPhone/iPod

- For iPad, iPhone or iPod : Connect the iPad, iPhone or iPod to the docking station. Select the song or the desired playlist to play at the “Wake up” time. Start and pause playback of the song/playlist at the point from which you want playback to begin at the “Wake up” time.

- For radio : Tune in the desired station.

- For buzzer : No preparation is required.

- SoftWake: By default, the wake up volume will begin at 1 and softly increase to 16. To wake up to a louder volume please preset the desired volume before going to sleep.

5. Press the ALARM button to confirm & complete the alarm 1 setting.

6. The docking station should now have the hour digits flashing again for the Alarm 2 setting, and the Alarm 2 icon “ “ shown.

7. Repeat above steps 2 through 5 to complete the Alarm 2 settings.

SoundPad is equipped with 3 alarm modes:

1) Buzzer

2) Radio

3) iPad/iPhone/iPod

12 13

NOTE: Make sure to set the clock before setting the alarm. If the clock is not set the

display will show an “ERR” message.

Setting the Digital Clock

Operational Instructions

Press the button to put the docking station into “STANDBY” mode. In “STANDBY” mode, the display will continuously show the current time. In this situation the blue backlight is normally dimmed to save electricity.

Switch docking station to “STANDBY”

mode (display light = dimmed)

Correct time is now set & will be

shown on the display.

Press & hold the DISPLAY/CLOCK Adj. button for 3 seconds.

Display shows “12H” Hour or “24H” hour (flashing)

Press the

or button to select 12-hour or 24-hour clock display system

& press the DISPLAY/CLOCK Adj. button to confirm your selection

Press the

or button repeatedly to set the correct hour in the display

& press the DISPLAY/CLOCK Adj. button to confirm

Press the

or button repeatedly to set the correct minute in the display

& press the DISPLAY/CLOCK Adj. button to confirm

how to set the correct time

Page 8

Page Page

Operational Instructions

Electronic Volume Control

14 15

Music Equalizer

At anytime during playback, press EQ/SLEEP button repeatedly to choose the desired sound effect according to the music you are listening to :

BASS CLASSIC

POP

JAZZ

ROCKOFF

Dimmer Function

2. When the desired area (L1/L2/L3) is displayed, press the or button to adjust the

brightness level of that area.

L1 = Ambient under lighting

L2 = Control buttons lighting

L3 = Display backlight

* Brightness setting confirmed

* When brightness settings are confirmed, the docking station will display the clock.

* When brightness settings are confirmed, the docking station will display the clock time.

SoundPad has a dimmer function to adjust the brightness level of the display backlight. Simply adjust as desired by pressing the DIMMER button repeatedly (hi-dimmer/ lowdimmer/OFF) to reduce eye strain and save energy. The display backlight will always return to hi-dimmer after reset of the docking station.

1. Press the DIMMER button repeatedly to choose the lighting area you wish to adjust:

- To increase or decrease the loudness of SoundPad, press the VOL. UP or VOL. DOWN button respectively.

- Release the button when the desired volume level is reached.

- Sometimes, especially when listening to the radio, you may notice a “click-click-click” (repeating) sound when you are increasing or decreasing the volume. This is a normal condition & the sound will disappear when you release the volume button.

Operational Instructions

Turning the Alarm ON/OFF

Press the button to turn the docking station into “STANDBY” mode. In “STANDBY” mode, press the ALARM button repeatedly to choose the desired alarm setting:

OFF: No Alarm Icon

Alarm 1

Alarm 2

Dual Alarm

2122

Snooze Function

- When the alarm rings it can be temporarily suspended for a short period of 9 minutes

by pressing the SNOOZE button once. In this period you will observe “SNOOZE” icon will be flashing on the display.

- The alarm will then automatically come on again after the 9 minute “SNOOZE” period has ended.

- This procedure can be repeated for approximately an hour from original alarm wake up time.

- Press the ALARM button to turn off the alarm completely.

Sleep Function

- SoundPad has a special sleep timer which can automatically turn off the docking station after a preset amount of time. This is useful for sleeping to your music at night.

- At any time while SoundPad is operating, press & hold the EQ/SLEEP button to access the “SLEEP TIME” function. Then press the EQ/SLEEP button repeatedly to choose the automatic power off time. During this mode you observe sleep icon on the display.

mins80mins

mins10mins

00*

* 00 means sleep timer is deactivated

If the alarm is set to iPod, you need to make certain the iPad, iPhone or iPod is connected properly and using docking station power rather than the battery power of the device. Otherwise, the buzzer alarm will sound at the set time.

important!

Page 9

Page Page

Operational Instructions

Operation with iPad, iPhone or iPod*

“Made for iPad,” “made for iPhone,” and “made for iPod” means that an electronic accessory has been designed to connect specifically to iPad, iPhone or iPod, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPad, iPhone or iPod may affect wireless performance.

16 17

* NOTE: Due to accessory restrictions by Apple (such as this product), the following iPods

will not charge when docked in this product: iPod Classic/iPod 4G/iPod 5G

- Turn on the docking station by pressing button.

- Turn on the power of your iPad, iPhone or iPod and insert into the docking station.

- Press the FUNC. button repeatedly until the display shows “iPod”.

- Press the button on the docking station to begin playback.

- The iPad/iPhone/iPod display will indicate the information of the current song.

- At anytime during playback, press the button to pause playback. Press button to resume playback of the same song and position.

- At anytime during playback, press and release the or buttons to skip forward or backwards by one song, as desired.

- At anytime during playback, press and hold the or buttons to fast-forward (cue) or fast-reverse (review) current song.

- You can operate the iPad/iPhone/iPod using either the docking station’s buttons, or directly with the iPad/iPhone/iPod itself.

- When your iPad/iPhone/iPod is connected to the docking station, it will start charging the battery of the iPad/iPhone/iPod.

- It is recommended that playback of your iPad/iPhone/iPod be paused before removing it from the docking station to prevent damage to your song files.

Manual Station Adjustment

- Press (and immediately release) the or buttons to “SCAN” (manually adjust) the radio

stations “UP” or “DOWN” 1-frequency at a time.

- The digital display will indicate the exact station at each step’s position.

- When a desired station is reached, it can be saved into one of the “MEMORY” positions. (See “RADIO MEMORY” section below.)

Automatic Station Adjustment (Seek Mode)

- Press and hold (for 2 seconds) the or buttons to automatically “SEEK” the radio stations “UP” or “DOWN” to the next available station in your area.

- The digital display will indicate the exact frequency of the next station that is found.

- When a desired station is reached, it can be saved into one of the “MEMORY” positions. (See “RADIO MEMORY” section below.)

Radio Memory (Station Preset Memory Storage)

- At any time, the currently displayed station or frequency can be stored into one of the memory positions.

- Press and hold the MEMORY button until “01” flashes in the display.

- Press the or buttons to select desired memory position. (There are a total of 30 memory positions.)

- Press the MEMORY button once to save the selected station into the selected memory position.

- To recall any station saved to memory, simply press the MEMORY button once and use the or buttons to navigate your preset stations.

- To clear the memory of any position, simply save a new station to the same memory position.

Operational Instructions

Radio Operation

- Press the button once to turn on the docking station.

- Press the FUNC. button repeatedly until the display shows “TUNER”.

- Extend and adjust the FM-wire antenna to obtain the best reception.

Page 10

Page Page 18 19

Troubleshooting

Symptom

SoundPad does not respond (no power)

iPad/iPhone/iPod does not dock properly

iPad/iPhone/iPod does not respond to the SoundPad

iPad/iPhone/iPod is not charging

Possible cause

AC adapter is not plugged into a wall outlet or the connector is not plugged into the DC IN jack on the back of the docking station.

iPad/iPhone/iPod is not installed properly.

iPad/iPhone/iPod is locked up/ frozen.

iPad/iPhone/iPod battery has a problem.

iPad/iPhone/iPod is locked up/ frozen.

Using first or second generation iPad/iPod, iPod shuffle or other devices.

Solution

Verify the AC adapter is plugged into wall outlet and the DC IN jack properly.

Remove the iPad/iPhone/iPod from the docking station and check for obstruction on the connections of the docking station and of the iPad/ iPhone/iPod. Then reset the iPad/ iPhone/iPod into the docking station.

Make sure your iPad/iPhone/iPod is working properly before docking it into the docking station. Please refer to the iPad/iPhone/iPod manual for details.

SoundPad cannot control these iPads/iPods or other devices.

Remarks:

If troubleshooting does not eliminate the problem, disconnect the DC IN plug from the back of docking station and reconnect it after a few seconds. This resets the docking station to it’s factory default settings and results in the deletion of all previous settings. In case the problem still exists, see warranty information on page 22 to obtain service.

Operational Instructions

Using the Audio Line in Connection (AUX-INPUT)

- You can connect the audio input of an external device, such as a MP3 player or a TV, to SoundPad for listening to the sound of that device through the high quality amplifier of the docking station.

- To connect the external device, use a standard stereo headphone (3.5 mm) cable to connect the “HEADPHONE-OUT” or “AUDIO LINE-OUT” of the device to the AUXINPUT socket of the docking station.

- Switch on the docking station and the external device (eg. MP3-player or TV).

- Switch the function to AUX using the FUNC. button.

- Start playback of the external device and adjust the volume control of the docking station to the desired level.

- Remember to switch off the docking station when you are finished using the external device.

Page 11

Page Page 20 21

Speciﬁcations

- Power supply: DC 12V, 2Amps through built-in DC jack External AC-DC power adaptor 110V-240V ~ 50/60Hz

- Speaker: 2 ½” x 2

- Speaker power: 5W x 2

- Frequency: FM 87.5-108 MHz

Compliance with FCC Regulations

The equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate Radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to Radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to Radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced Radio / television technician for assistance.

THE SPECIFICATION AND EXTERNAL APPEARANCE OF THE MUSIC DOCK ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.

If at any time in the future you should need to dispose of this product please note that: waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Page 12

Page Page 22 23

purchase date:

place of purchase:

Limited Warranty

The AT&T brands are used under license. Any repair, replacement, or warranty service, and all questions about this product should be directed to Concept 101 LLC at www.att.com/electronics or call 1

(888) 920-8680 from the USA or Canada.

Concept 101 LLC warrants to the original purchaser that the product will be free from defects in material, parts and workmanship for the period designated for this product. The warranty commences the day the product is purchased and covers up to a period of one (1) year (90 day Labor and 1 year Parts). Concept 101 LLC agrees that it will, at its option, replace the defective product with either a new or remanufactured docking station equivalent to your original purchase during the warranty period. Should the Parts warranty period exceed the Labor warranty period, Concept 101 LLC will supply at no charge for the remainder of the Parts warranty, any new or re-manufactured replacement parts as required by the product. During this period all labor and service charges will become the responsibility of the customer.

Exclusions: This warranty does not apply to the appearance or exterior of the product which may have

been damaged or defaced, altered or modified in design or construction. This warranty does not apply if the serial number is altered or removed, or if there is any damage due to power line surge, user damage to the AC power cord, connection to improper voltage source, general misuse, accidents, or repair attempts by unauthorized service agents. Other exclusions include ear pads, rechargeable and non-rechargeable batteries.

Warranty Information

Obtaining Service: To obtain service, product literature, supplies or accessories please call

1 (888) 920-8680, or visit our website, www.att.com/electronics, to create

a ticket for exchange/repair. Please make sure to provide the date of purchase, model number and a brief description of the problem. Our customer service representative will contact you or send detailed return instructions.

REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CUSTOMER; Concept 101 LLC SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT, EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE DURATION OF THE WARRANTY.

Some states do not allow the exclusion or limitations of incidental or consequential damages, or limitations on how long the warranty lasts. In these cases the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Concept 101 LLC does not warrant that the docking station will work properly in all environmental conditions, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose other than the purpose identified within this user’s manual. Concept 101 LLC has made every effort to ensure that this user’s manual is accurate and disclaims liability for any inaccuracies or omissions that may have occurred. Information in this user’s manual is subject to change without notice and does not represent a commitment on the part of Concept 101 LLC. Concept 101 LLC reserves the right to make improvements to this user’s manual and/or to the products described in this user’s manual at any time without notice. If you find information in this manual that is incorrect, misleading, or incomplete, please contact us through our website.

Page 13

©2012 Concept 101 LLC. All Rights Reserved. AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to Concept 101 LLC, New York, New York 10018. Printed in China. Issue 11 AT&T 03/2012.

www.att.com/electronics

AT&T ID501 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual