AT&T Design Line 146 User Manual

Download

Page 1

AT&T and the globe symbol are registered trademarks of

AT&T Corp. licensed to Advanced American Telephones.

Printed in China. 850005059 Issue 1AT&T 12/00

USER’S MANUAL

Part 2

INSTALLATION

Please also read

Part 1 – Important

Product Information.

Design Line

Telephone 146

4 Pull phone down

onto mounting

studs as shown.

5 Follow Steps 3-5

in Table/Desk,

above.

Table/Desk

Wall

3 Press the cord into the channel as shown,

and connect to the free end of the line cord

to the modular wall jack.

2 Connect the short line cord to the telephone.

1 Reverse the handset tab as shown.

1 Connect the long line cord to the telephone.

2 Press the cord into the channel as shown,

and connect the free end of the line cord

to the modular wall jack.

3 Set the dial mode switch to TONE if you have

touch tone service or to PULSE if you have

dial pulse service.

4 Connect the handset to the base using

the coiled cord. Hang up the handset.

5 Lift the handset and check

for dial tone.

Dial mode

switch

NOTE: If you do

not reverse the

handset tab, the

handset will not

stay in the cradle

when used on a

wall. If you later

move this phone

to a table or desk,

be sure to reverse

the handset tab

again.

Dial

mode

switch

Page 2

IN CASE OF DIFFICULTY

If you have difficulty operating this phone, tr y the suggestions below. For Customer Service, visit our website at www.telephones.att.com or call 1 800 222-3111. Please

retain your receipt as your proof of purchase.

No Dial Tone

• Make sure all plugs are connected properly. Inspect the line cord connections at the modular jack and at the telephone. Also inspect the coiled handset cord connections at both ends.

• Unplug the telephone and connect it to another modular jack. If it still does not work, try another telephone; if neither telephone works the problem is not in this telephone. Contact your telephone service provider.

Calls Cannot Be Dialed or Are Dialed Slowly

Check the dial mode switch; make sure it is set for your type of dialing service (TONE or PULSE).

Telephone Does Not Ring or Rings Too Softly

• Make sure the RINGER switch is not set to OFF.

• You may have inadvertently turned off the ringer when selecting a ringer tone. Press , #, 6, to turn the ringer back on.

• You might have too many extension phones on your line to allow all of them to ring. Try unplugging some of them.

You Can Hear Other Party but Other Party Can’t Hear You

The Mute feature might be activated. Try pressing . If this doesn’t work, try pressing

again.

OPERATION

Select Ringer Tone

You can select from three different ringer tones. The phone comes set to Tone 2.

1 Press . 2 Press #. 3 Press 3 for Tone 1

— OR —

Press 6 for Tone 2

— OR —

Press 9 for Tone 3.

4 Press to save your

selection.

Store Memory Numbers

This phone can store 10 telephone numbers, each up to 21 digits long.

1 Lift the handset. 2 Press . 3 Press m . 4 Enter a memory location (0 - 9)

where the number is to be stored.

5 Enter the telephone number.

You’ll hear a click each time you press a button.

6 Press . 7 Hang up. 8 Repeat Steps 1 to 7 to store

another number.

Dial Memory Numbers 1 Lift the handset and listen for a

dial tone.

2 Press m . 3 Press the memory location

(0 - 9).

Erase Memory Numbers

To erase any number from memory, store another number in its place.

NOTE: Memory numbers and redial memory will be lost if the phone is unplugged from wall jack for more than 30 minutes.

Directory Card

A directory card is provided for your convenience to record numbers stored in memory.

OPERATION

Adjust the volume of what you hear through the handset from NORMAL to LOUD.

Adjust the volume of the ringer from

OFF to LO to HI.

Dial the last number

called from this phone

(up to 31 digits).

To erase redial memory,

lift the handset, press

any digit, then hang up.

Access special

telephone company

subscriber services

such as Call Waiting.

Change from dial pulse to tone dialing during a call.

1 Dial the number. 2 Press *.

All buttons pressed after this send tone signals.

3 After you hang

up, the phone returns to dial pulse service.

While on a call, press to prevent the other party from hearing you (you can still hear the other party). Press again to return to two-way conversation.

3 4