AT&T CL82100 User Manual

Quick start guide

CL82100/CL82200/CL82250/
CL82300/CL82350/CL82400/
CL82450/CL82500/CL82550/
CL82600
DECT 6.0 cordless telephone/
answering system with
caller ID/call waiting

Installation

You must install and
charge the battery before
using the telephone.

Install the telephone base close to a telephone jack and a power outlet not
controlled by a wall switch. The telephone base can be placed on a flat surface
or vertically mounted on the wall. For optimum range and better reception,
place the telephone base in a central and open location.

If you subscribe to high-speed Internet service (DSL - digital subscriber line)
through your telephone line, you must install a DSL filter between the
telephone line cord and the telephone wall jack (see the following page). The
filter prevents noise and caller ID problems caused by DSL interference. Please
contact your DSL service provider for more information about DSL filters.

Your product may be shipped with a protective sticker covering the handset
or telephone base display - remove it before use.

For customer service or product information, visit our website at

STOP!

See pages 2-4
for easy instructions.

www.telephones.att.com or call 1 [phone]. In Canada, dial
1 [phone].

Avoid placing the telephone base too close to:

Communication devices such as: television sets, VCRs, or other

•
cordless telephones.

Excessive heat sources.

•
Noise sources such as a window with traffic outside, motors, microwave

•
ovens, refrigerators, or fluorescent lighting.

Excessive dust sources such as a workshop or garage.

•
Excessive moisture.

•
Extremely low temperature.

•
Mechanical vibration or shock such as on top of the washing machine

•
or workbench.

1

Telephone base and charger installation

Install the telephone base and charger as shown below.
The telephone base is ready for tabletop use.

Telephone base installation

Plug the other end

•

of the telephone
line cord into a
telephone jack or
a DSL filter.

Telephone line cord

Raise the antenna.•

Power
adapter

If you have DSL high-speed
Internet service, a DSL filter
(not included) is required.

Plug one end of the

•

telephone line cord
into the telephone jack
on the bottom of the
telephone base.

Plug the small end of

•

the telephone base
power adapter into the
power adapter jack
on the bottom of the
telephone base.

Route the power

•

adapter cord through
this slot.

Place the cords into

•

the channels.

Plug the large end

•

of the power adapter
into a power outlet
not controlled by a
wall switch.

Charger installation

Plug the power adapter into an electrical outlet
not controlled by a wall switch.

IMPORTANT INFORMATION

1. Use only the power adapter(s) supplied with this product. To order a replacement
power adapter, visit our website at www.telephones.att.com or call

1 [phone]. In Canada, dial 1 [phone].

2. The power adapters are intended to be correctly oriented in a vertical or floor
mount position. The prongs are not designed to hold the plug in place if it is
plugged into a ceiling, under-the-table or cabinet outlet.

2

Battery installation and charging

Install the battery as shown below. Once you have installed the battery, the

screen indicates the battery status (see table below). If necessary, place the
handset in the telephone base or charger to charge the battery. For best
performance, keep the handset in the telephone base or charger when not in
use. The battery is fully charged after 16 hours of continuous charging.

If the screen shows Place in charger and flashes, you need to charge the
handset without interruption for at least 30 minutes to give the handset

enough charge to use the telephone for a short time. The following table

summarizes the battery charge indicators and actions to take.

Battery indicators Battery status Action

The screen is blank or
shows Place in charger and

(flashing).

The screen shows
Low battery and (flashing).

The screen shows
HANDSET X.

NOTE: If you are on a phone call in low battery mode, you hear four short beeps
every minute.

Battery has no or very
little charge. The handset
cannot be used.

Battery has enough charge
to be used for a short time.

Battery is charged. To keep the battery charged,

Charge without interruption until
the screen shows Low battery or
HANDSET X (at least 30 minutes).

Charge without interruption until
the screen shows HANDSET X
(at least 30 minutes).

place it in the telephone base or
charger when not in use.

Step 1

Plug the battery
connector securely
into the socket inside
the handset battery
compartment, matching
the color-coded label.
Insert the supplied
battery with the label
THIS SIDE UP facing up
as indicated.

Step 2

Align the cover flat
against the battery
compartment, then
slide it upwards until
it clicks into place.

3

Battery installation and charging

CHARGE light

Step 3

Charge the handset by placing it face forward in
the telephone base or charger. The CHARGE light
on the top of the handset is on during charging.

SET DATE

--/--/--

SET TIME

After you install your telephone or power returns following
a power outage, the handset will prompt you to set the date
and time. To skip setting the date and time, press OFF/CLEAR.

IMPORTANT INFORMATION

1. Use only the supplied rechargeable battery or replacement battery (model BT166342).

To order, visit our website at www.telephones.att.com or call

1 [phone]. In Canada, dial 1 [phone].

2. If you do not use the handset for a long time, disconnect and remove the battery
to prevent possible leakage.

--:-- --

4

Quick reference guide - handset

CHARGE indicator

On when the handset is
charging in the telephone base
or charger.

qCID/-VOLUME

Press qCID to show caller ID
history.

Press to scroll down while
in menus.

While entering names or
numbers, press to move the
cursor to the left.

Press to decrease the listening
volume when on a call.

PHONE/FLASH

Press to make or answer a call.

During a call, press to answer
an incoming call when you
receive a call waiting alert.

1

While reviewing a call log
entry, press repeatedly to
add or remove 1 in front of
the telephone number before
dialing or saving it in the
directory.

TONE

Press to switch to tone dialing
temporarily during a call if you
have pulse service.

/SPEA�ERSPEA�ER

Press to switch between
speakerphone and handset.

MENU/SELECT

Press to show the menu.

While in the menu, press to
select an item or save an
entry or setting.

pDIR/VOLUME+

Press pDIR to show
directory entries.

Press to scroll up while
in menus.

While entering names or
numbers, press to move the
cursor to the right.

Press to increase the
listening volume when on
a call.

OFF/CLEAR

During a call, press to hang up.

While in a menu, press to
cancel an operation, back up
to the previous menu, or exit
the menu display.

Press and hold while the
telephone is not in use to
erase the missed calls indicator.

#

Press repeatedly to display
other dialing options when
reviewing a call log entry.

REDIAL/PAUSE

Press repeatedly to view the
last 20 numbers dialed.

While entering numbers,
press and hold to insert a
dialing pause.

MUTE/DELETE

During a call, press to mute the microphone.

While reviewing the caller ID history, the directory or
the redial memory, press to delete an individual entry.

While predialing, press to delete digits.

5

INT

Press to begin an intercom
conversation or to transfer
a call.

Quick reference guide - handset

During an outside call, intercom call,
message or announcement playback,
press to change the quality of the audio
to best suit your hearing.

EQ

Main menu

The > symbol highlights
a menu item.

>Play messages

Answering sys

Main menu

Play messages
Answering sys
Directory
Call log

Ringers
Settings
Website

Using menus

Press MENU/SELECT to show the first menu
item, Play messages.

Press qCID or pDIR to scroll through
menu items.

Press MENU/SELECT to confirm or save
changes to a highlighted menu item.

Press OFF/CLEAR to cancel an operation,
back up to the previous menu, or exit the
menu display.

6

Quick reference guide - telephone base

X/DELETE

Press to delete the
message currently playing.

Press twice to delete all
old messages when the
phone is not in use.

/ANSWER ON

Press to turn the built-in
answering system on
or off.

pqVOLUME

During message
playback, press to adjust
the listening volume.

While in idle mode,
press to adjust the base
ringer volume.

Message counter

Number of messages
(or during playback,
message number
currently playing).

/PLAY/STOP

Press to start or stop
message playback.

/REPEAT

Press to repeat a message.

Press twice to play the
previous message.

/S�IP

Press to skip a message.

/HANDSET LOCATOR

Press to make
handsets beep so you
can locate them.

IN USE indicator

On when the handset is in
use, or when the answering
system is answering an
incoming call.

On when a handset is
being registered.

Flashes when there
is an incoming call or
when a handset is being
deregistered.

Flashes when another
telephone is in use on
the same line.

7

Answering system settings

Announcement

Your outgoing announcement plays when calls are answered by the
answering system.

The telephone has a default outgoing announcement, “Hello. Please leave a
message after the tone.” You can use this announcement, or record your own.

You can record an announcement up to 90 seconds. The system does not
record any announcement shorter than two seconds.

To play your current outgoing announcement:

1. When the handset is in idle mode, press MENU/SELECT to
enter the main menu.

2. Press qCID or pDIR to scroll to >Answering sys, then
press MENU/SELECT.

3. Press MENU/SELECT again to select >Announcement. The
system announces, “To play, press 2. To record, press 7.”

4. Press 2 to play the current announcement.

To record a new outgoing announcement:

1. When the handset is in idle mode, press MENU/SELECT to
enter the main menu.

2. Press qCID or pDIR to scroll to >Answering sys, then
press MENU/SELECT.

3. Press MENU/SELECT again to select >Announcement. The
system announces, “To play, press 2. To record, press 7.”

4. Press 7 to record an announcement. The system announces,
“Record after the tone. Press 5 when you are done.”

5. Facing the handset, record your announcement and press
5 to end recording. Your recorded announcement plays.

Play messages

>

Answering sys

>

Announcement

Delete all old

2-Play 3-Delete
5-Stop 7-Record

Record annc...
5-Stop

To listen to the recorded announcement again, press 2 after
playback is completed. To record a new announcement, press 7 and follow
the above steps in the To record a new outgoing announcement section.

To delete your outgoing announcement:

1. When the handset is in idle mode, press MENU/SELECT to enter the
main menu.

2. Press qCID or pDIR to scroll to >Answering sys, then press MENU/SELECT.

3. Press MENU/SELECT again to select >Announcement. The system
announces, “To play, press 2. To record, press 7.”

4. Press 3 to delete your recorded announcement.

When your announcement is deleted, the system answers calls with the
default announcement.

8

www.telephones.att.com

© 2009-2010 Advanced American Telephones. All Rights Reserved.

AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to

Advanced American Telephones, San Antonio, TX 78219.

Printed in China. Issue 6 AT&T 03/10.