Design Line Telephone 145
USER’S MANUAL
Part 2
AT&T and the globe symbol are registered trademarks of AT&T Corp.
licensed to Advanced American Telephones.
© 2000 Advanced American Telephones. All rights reserved.
Printed in China. 850003054 Issue 1AT&T 6/00
Please also read
Part 1 — Important
Product Information
MEMORY
PROGRAM
1
FLASH
ABC
2
GHI
4
5
PQRS
7
TUV
8
TONE
OPER
0
REDIAL
DEF
3
JKL
MNO
6
WXYZ
9
#
TONE PULSE
RINGER OFF LO HI
Dial Mode
This telephone has a selectable push-button dial and will
work with either tone or rotary telephone service. It can
be set to work directly with long-distance or certain other
services that require tone signaling including some tone
activated computer systems.
RINGER OFF LO HI
TONE PULSE
1
2
3
4
5
6
7
ABC
DEF
GHI
JKL
MNO
PQRS
TUV
WXYZ
TONE
OPER
MEMORY
PROGRAM
FLASH
REDIAL
8
9
0
#
Dial Mode
switch
INSTALLATION
1
Temporary
Tone
Handset
Redials
last call
made
Accesses numbers
stored in memory
Receiver Volume
(on left side of base)
Ringer
Volume
Programs a number
in memory
Accesses custom
calling services
TABLE/DESK INSTALLATION
This telephone includes a 7-foot line cord with a modular
plug on each end. You’ll use this cord to connect the
telephone to a modular jack.
1. Connect line cord to telephone
Plug the long line cord into the jack on the underside of
the telephone base. Then feed the line cord through the
channel provided so the telephone sits flat on your table
or desk during use.
2. Set Dial Mode switch
This product comes set in the TONE mode. Make sure
you choose the correct dialing method (TONE/PULSE);
touch tone dialing will not work if you have dial pulse
service.
3. Connect handset to base
Plug one end of the coiled cord into the handset, and
the other end into the telephone base. Then hang up.
4. Connect line cord to modular jack
Plug the free end of the line cord into a modular jack.
Make sure it snaps firmly in place.
5. Check for dial tone
Lift the handset and listen for a dial tone. If you can’t
hear a dial tone, refer to “In Case of Difficulty” and try
to correct the problem.
TO DISCONNECT the telephone, squeeze the clip on
the modular plug and pull it out of the jack.
2
INSTALLATION
WALL INSTALLATION
1. Reverse the handset tab.
When mounting the telephone on a wall, you must
reverse the handset tab. This tab holds the handset when
you hang up. Hold down the switchhook, and slide the
tab up and out of its slot (Figure 1). Turn the tab so that
the end with the “hook” is up (Figure 2). Then insert the
tab back into its slot (Figure 3).
2. Fill in directory card
The enclosed directory card has an adhesive backing
which lets you place it in a convenient location near the
telephone. Write in your own telephone number and up
to nine other numbers you want to remember on the
directory card.
3. Plug the line cord into the jack on the underside of
the base
Feed the short line cord into the channel. Feed the last
portion (as short as possible), through one of the slots in
the mounting area.
4. Install telephone base on wall jack
Hold the base up next to the wall jack and plug in the line
cord. Then push the base against the wall jack and down
until it is held securely by the mounting studs.
3
INSTALLATION
Figure 1 Figure 2 Figure 3
5. Set the Dial Mode switch
This product comes set in the TONE mode. Make sure
you choose the correct dialing method (TONE/PULSE);
touch tone dialing will not work if you have dial pulse
service.
6. Connect handset to telephone base
Connect one end of the coiled handset cord to
the base. Plug the other end into the handset. Then hang
up the phone.
7. Check for dial tone
Lift the handset and listen for a dial tone. If you can’t
hear a dial tone, refer to “In Case of Difficulty” and try
to correct the problem.
NOTE: If you cannot fit the base onto the wall jack plate,
remove the top two non-slip feet.
INSTALLATION
4
Line Jack
Figure 4
Handset
Jack
Wall Jack
5
Redial
The telephone always stores in memory the last number
dialed. To dial the same number again, lift the handset, and
press .
The redial memory can accept numbers up to 32 digits long.
The number will remain in memory until you change it by
dialing another telephone number.
For privacy, you can erase the redial memory. Lift the
handset, then press any digit (1-9).
Flash
Press instead of pressing the switchhook to activate
customer calling services such as call waiting or three-way
calling. You may have to press other buttons before or after
as explained in custom calling instructions provided
by your local telephone company.
Ringer Volume
The RINGER volume switch allows you to adjust the loudness of the telephone ringer from OFF to LO to HI. Slide
the switch to the desired volume level.
Receiver (Handset) Volume
The Receiver volume switch on the left side of the base has
three positions which allow you to adjust the loudness of
your call from NORMAL to LOUD. Slide the switch to the
desired volume level.
Temporary Tone
Temporary tone dialing is used only when you have rotary
service. It allows you access to services that require tone
signaling, including some tone-activated computer systems
(e.g., telephone banking).
To change from pulse (rotary) to tone dialing during a call:
1. Dial a telephone number with the dial mode switch set to
PULSE.
2. Press ; all buttons pressed after this will send
tone signals.
3. After you hang up, the phone automatically returns to
rotary service.
OPERATION
REDIAL
FLASH
FLASH
TONE
Memory Features
Numbers will remain stored in memory unless you erase or
change them by entering other numbers.
Capacity: This telephone can store up to nine different
phone numbers, each up to 18 digits long.
Speed Dialing: Nine telephone numbers can be stored in
standard speed-dialing locations. You can dial any of these
numbers by pressing two buttons.
NOTE: Numbers programmed into a memory location
might not be retained if the telephone has been unplugged
from the line jack for a half hour or more.
Speed Dialing
To program numbers into memory:
1. Press .
2. Enter telephone number. You will hear a click when
each button is pressed.
3. Press .
4. Enter a digit (1-9) for the memory location where the
number is to be stored.
5. Hang up after the number is entered correctly.
Repeat steps 1-5 to store another number.
To dial:
1. Listen for dial tone.
2. Press .
3. Press memory location (1-9).
Memory Erase
To erase any number from memory, you can enter another
number in the same location.
MEMORY
6
PROGRAM
MEMORY
MEMORY
7
If you have difficulty operating this phone, try the
suggestions below.
No Dial Tone
☞ Make sure all plugs are connected properly. Inspect
the line cord connections at the modular jack and at
the telephone. Also inspect the coiled handset cord
connections at both ends.
☞ Unplug the telephone and connect it to another modular
jack. If it still does not work, try another telephone; if
neither telephone works, the problem is not in this
telephone. The trouble may be caused by local telephone
company lines, central office equipment, or the wiring
in your home.
Calls Cannot Be Dialed, or Are Dialed Slowly
Reset Dial Mode switch. If you have rotary service, you
cannot dial numbers with the switch set to TONE. Set the
switch to PULSE, then hang up and dial again.
If you have tone dialing service, you can use either tone or
dial-pulse mode. If you set the switch to TONE, numbers
are dialed much more quickly.
Telephone Does Not Ring
☞ Make sure the Ringer switch is not set to OFF.
☞ If there are several other phones on the same line, try
disconnecting some of the other telephones. Having too
many telephones can also create problems such as low
ringer volume or impaired quality during calls.
Other Problems
For customer service, visit our website at
www.telephones.att.com or call 1 800 222-3111.
Please retain your receipt as your proof of purchase.
IN CASE OF DIFFICULTY
Loading...