All specs are subject to change without notice. ATS005309 RevA 9/16
General Description
AtlasIED I8SCMF+ is an indoor wall mount IP loudspeaker with
integrated talkback microphone, LED display and LED flasher. It
leverages VoIP communication to extend tele-presence with enhanced
audio for environments where network-wide communication is desired
and high-output loudspeakers are required to overcome high ambient
noise and/or large spaces.
Applications
AtlasIED I8SCMF+ registers as a communication endpoint directly
within InformaCast, GCK, and SA-Announce advanced notification
applications, supporting audio broadcast to enhance physical security
while improving day-to-day communications through advanced
alerting, bell schedules, pre-recorded & scheduled announcements,
while leveraging the WAN or LAN network architecture.
When used within a Cisco environment, the I8SCMF+ loudspeakers
can join Cisco’s Unified Survivable Remote Site Telephony (SRST)
as a supported device. Cisco’s SRST provides remote location
call-processing redundancy when access to the centralized Cisco
Unified Communications Manager is interrupted because of a WAN
outage. The ability of LAN communication between any combination
of phones and loudspeakers is particularly critical during an
emergency (which may be the actual cause of the WAN outage).
Where 3rd party notification applications are not required, the
I8SCMF+ loudspeakers can register as SIP devices directly to a SIP
server or VoIP Communications Manager for critical alerts, intercom
and public address applications.
Under Title II of the ADA, all state and local governments are
required to take steps and ensure effective communication to
people with disabilities. The AtlasIED I8SCMF+ IP loudspeakers with
talkback microphone, LED display and LED flasher provide effective
communication for all individuals.
1601 JACK MCKAY BLVD.
ENNIS, TEXAS 75119 U.S.A.
TELEPHONE: (800) 876-3333
FAX (800) 765-3435
AtlasIED.com
Page 2
System
TypePoE+ Indoor IP Loudspeaker System with LED Display, Microphone and LED Flasher
Operation ModeSelf Powered
IndicatorsNetwork Status (On Back)
Operating Range (-10db)70Hz - 15.5kHz
Frequency Response (+/- 5dB)86Hz - 15.5kHz
Vertical Coverage105° 800Hz - 4kHz
Horizontal Coverage105° 800Hz - 4kHz
Directivity Factor (Q)4.7 @ 2 kHz
Max SPL at 1 m (passive)106 dB SPL Continuous / 109 dB SPL Peak
Recommended Signal ProcessingBuilt-In Processing
General Purpose InterfaceTwo Trigger Inputs / One Relay Output (2A @ 30 VDC)
Transducers
Transducer Qty and Size8"
Voice Coil Size1"
Cone MaterialCurvelinear, Treated Industrial Paper
Driver ProtectionBuilt-In Limiter
Amplication
TypeSingle-Channel Class D Topology
AC Power InputPoE or PoE+ and External 24VDC
Power Rating (RMS)15 Watts Max (802.3AT)
THD<.02%
CoolingPassive/Convection
Microphone
SensitivityMinus 35 (±4dB) / (0db = 1V/pa, 1kHz)
ImpedanceLess than 2.2kΩ
DirectivityOmnidirectional
Frequency Range20Hz – 20kHz
Standard Operation Voltage2V
Max. Operation Voltage10V
Current Consumption Max.0.5 mA
Sensitivity Reduction WithinMinus 3dB @ 1.5V
S/N RatioMore than 62dB
Audio Inputs and Outputs
Input: Analog Audio Type(s)One Unbalanced Analog
Input: Analog ConnectivitySecured Screw Terminal Block
Input: Network Audio Type(s)G.711 U-Law/A-Law and G.722 Capable
Input: Network ConnectivityRJ-45 Female
Output: Analog Audio Type(s)One Unbalance Line Level
Output: Analog ConnectivitySecured Screw Terminal Block
All specs are subject to change without notice. ATS005309 RevA 9/16
1601 JACK MCKAY BLVD.
ENNIS, TEXAS 75119 U.S.A.
TELEPHONE: (800) 876-3333
FAX (800) 765-3435
AtlasIED.com
Page 9
Architect and Engineer Specications
9/9
The unit shall be AtlasIED model I8SCMF+. The loudspeaker system
shall include factory assembled loudspeaker, IP addressable PCB
amplifier/control, metal baffle, integrated microphone, LED display and
LED flasher. The loudspeaker shall be an 8" driver with a 10oz (260g)
ceramic magnet and seamless cone. The impedance shall be 8 ohm and
a voice coil diameter of 1" (25mm). The loudspeaker dispersion shall be
105° (800Hz - 4kHz) and frequency response of 86Hz – 15.5kHz (±5dB).
The max peak output at 1W/1m shall be 98dB SPL.
The amplifier/control board shall be capable of producing 15-watts
RMS when using an IEEE 802.3at compatible PoE+ switch or 24VDC
local power supply and 9-watts RMS when used with an IEEE 802.3af
compliant PoE switch. Interconnect shall be via female RJ-45 connector
mounted to the PCB.
The unit shall incorporate an integrated microphone to allow full duplex
talkback communication functionality based upon chosen software
platform.
The unit shall incorporate a LED display with viewable dimensions of
10.125" (2577mm) wide x 2.56" (65mm) high. The LEDs per character
shall be 16 high x 64 wide and character max height of 2.125" (54mm).
It shall produce the color red and be controlled by Time via NTP. The
display shall produce 162 lux brightness and display text and/or time.
The unit shall incorporate a LED flasher with viewable dimensions of .5"
(12mm) height x 3.5" (89mm) wide. The LEDs shall be able to produce
RGB color spectrum with brightness of 310-lux (Red), 348-lux (Green),
352-lux (Blue). It shall have the capability of multi-speed flash rate and
will be software controllable.
All control functionality shall be determined via software. The metal
loudspeaker baffle overall dimensions shall be 14.38" (365mm) x 12.88"
(327mm) x 2.77" (70.36mm) HxWxD. Finish shall be neutral white
electrostatic powder coat.
Optional enclosures shall include:
SEA-I8SC surface mount angled enclosure for I8SCMF+
neutral white finish
SEST-I8SC surface mount straight enclosure for I8SCMF+
neutral white finish
FEST-I8SC flush mount straight enclosure for I8SCMF+