Atlas IED HPA602 Data Sheet

HPA602

Multi-Impedance High Power Ampliﬁer

Features

• Configurations

• 2 x 300 Watt 70V

• 2 x 300 Watt 100V

• 2 x 300 Watt 8Ω

• 2 x 300 Watt 4Ω

• Balanced Input Euro Block Phoenix Style Connectors

• Remote Turn On

• Accessory Card Slot for Optional Dante™ Digital Network Audio Card

• Fault Reporting

• Soft Clip Limiter Protection

• Stepped Attenuators with Security Covers

• Stereo or Parallel Operating Modes

• Selectable Input Sensitivity

• High Efficiency Fan Cooling

• Wide Range Global Power Supply with Power Factor Correction

• Meets Energy Star Standards for 1W Standby Mode

Applications

The HPA602 can be used for most audio applications, whether for commercially installed 70V/100V distributed systems, or professional high performance sound reinforcement applications. The HPA series will provide efficient, stable, and reliable power making them the perfect choice for night clubs, house of worship systems, portable sound systems, convention centers, sports venues, hotels, and retail centers.

General Description

The AtlasIED High Power Amplifier HPA Series model HPA602 has been designed to be used in both commercial 70V/100V distributed systems and professional applications that require amplifiers to handle 8Ω and 4Ω loads.

The HPA Series features Generation II Class D Output topology that provides superior efficiency with the sound quality of a Class AB amplifier. The power supply is a switch mode wide range design that maintains a stable output during fluctuating power conditions. The power supply and output stage collectively are designed to deliver exceptional dynamic high output voltage and current to virtually any loudspeaker load.

The HPA Series features front panel stepped level controls with a security cover, remote turn on, balanced line inputs with sensitivity settings, fault reporting and an accessory card slot for an optional Dante™ two-channel digital audio interface. Cooling is not an issue because of the unique output stage low resistance direct couple thermal transfer design. HPA also is energy efficient and meets Energy Star 1W standby mode standards.

Whether the application is a large distributed constant voltage sound system or a high SPL sound reinforcement system, the AtlasIED HPA Series is the answer for high power/cost effective reliable amplification requirements.

All other Trademarks are property of their respective owners. No endorsement is implied. Due to continual product development, specifications are subject to change without notice. ATS005609 RevC 3/19

1601 JACK MCKAY BLVD. ENNIS, TEXAS 75119 U.S.A.

TELEPHONE: (800) 876-3333 SUPPORT@ATLASIED.COM

AtlasIED.com

System

Type Power Amplifier, Two-Channel

Power Supply Type Switch Mode - Wide Range- PFC

Amp Topology Class D

Number of Fixed Inputs 2

Accessory Inputs 2

DSP Internal No

Network No

Optional Card Slot Ye s

Output Power (Note 1)

100V x 2 CH 2 x 300W

70.7V X 2 CH 2 x 300W

8Ω x 2 CH 2 x 300W

4Ω x 2 CH 2 x 300W

2Ω x 2 CH N/A

8Ω Bridged N/A

4Ω Bridged N/A

Factory Default Settings (As Shipped)

Amplifier Configuration 2 CH

Level Controls Front Panel

Control Ports (Rear Panel) Remote Turn On / Off, Enable On

Input Sensitivity .775 / 0dBu

Inputs

Input Quantity 2 Balanced Inputs, Expandable to 4 via Acccessory Card

Input Type Balanced Line

Input Connectors Type 3.5mm Euro Block

Input Impedance 20KΩ (Balanced) 10KΩ (Unbalanced)

Input Sensitivity 775mV / 1.0V / 32dB (Selectable)

Maximum Input Level dBu &Vrms 24dBu, 12V (Accessory Slot Refer to Accessory Card Specifications)

Accessory Slot 2 Input Dante™ Digital Card (HPA-DAC2 Optional)

Level Control

Front Panel Rotary Stepped Attenuators with Security Cover

Status Indicators

Power Blue

Standby Amber

AC Mains Out of Safe Operating Range Red

Temp Yellow

Ready Green

Signal Green

Output Limit Yellow

Output Protect Red

Bridge N/A

GPIO Ports (Rear Panel)

Number of Ports Qty 5

Type of Connector Euro Block 3.5mm

Functions Remote Turn ON via Contact Closure

Functions Remote Turn ON via DC Voltage 5-24V

Functions

Fault Report Contact - NC Under Safe Operating Conditions, NO When Fault is Detected, No AC Mains Power, Thermal, Shorted Output, Over Current

All other Trademarks are property of their respective owners. No endorsement is implied. Due to continual product development, specifications are subject to change without notice. ATS005609 RevC 3/19

1601 JACK MCKAY BLVD. ENNIS, TEXAS 75119 U.S.A.

TELEPHONE: (800) 876-3333 SUPPORT@ATLASIED.COM

AtlasIED.com

Conguration Settings (Rear Panel)

Input Senstivity .775V, 1V, 32dB per CH

Parallel Inputs Ye s

Bridge N/A

Output Terminals (Speaker)

Output Connectors Type Removable Euro Block, 7.62mm Pitch, Locking

Output Connectors Number of Terminals 4 Position

Wire Size 6-18 Gauge (Class 2 Wire)

Current Rating 57A per Terminal

Electrical Specications (General)

Total Harmonic Distortion 1 kHz and 1 dB Below Rated Power

Signal to Noise Ratio >70dB Below Rated Output (A-Weighted)

Frequency Response 20Hz - 20kHz (+0/-1.5dB)

Input Impedance Balanced (Nominal) 100 Ω Balanced Line to Line

Input Sensitivity 0.775V / 1.0V / 32dB (Selectable)

Slew Rate >10V/µs

Damping Factor (20Hz to 400Hz) >200

Gain 40dB (8Ω Factory Ship or 32dB Assignable)

Crosstalk CH1-2 & CH 2-1 >70dB

Max Voltage Per Output 8Ω 49V

Max Current per Output 4Ω 8.9A

Protection

AC Power Requirements

Operating Voltage Auto Switch, 50/60Hz 100V - 240V

Minimum Power-Up Voltage 95V

Maximum Operating Voltage 264V

Mains Connector C15 IEC Receptacle / Locking

Power Cord (Ships With) IEC 16-Gauge 1.5M Cord w/ NEMA 5-15 Male Plug

Power Consumption & Current Draw @ 120V AC Mains

Standby Mode 0.193A 0.7W 2.39 BTU

Idle Active 0.592A 43.5W 148.4 BTU

Average Power 4Ω, All CH Driven 1A 124W 269 BTU

Average Power 70.7V, All CH Driven 1.1A 134W 303 BTU

Max Power 4Ω, All CH Driven 7.3A 849W 856.4 BTU

Max Power 70V, All CH Driven 6.9A 802W 607 BTU

Cooling

Cooling System Fan (Varible With Temerature)

Air Inlet Filter Yes, Rear, Washable

Cooling Air Flow Direction Rear to Front

Dimensions and Weight

Rack Mount Requirements 2 RU, 19"

Dimensions - Unit 19" W x 3.5" H x 10.3" D (483mm x 89mm x 261mm)

Dimensions - Shipping 22" W x 6.69" H x 16.5" D (560mm x 170mm x 420mm)

Weight - Unit 14.8 lbs. (6.7kg)

Weight - Shipping 17.9 lbs. (8.1kg)

≤0.15%

Soft Start, Input RF, DC, Short Circuit, Current Overload, Clip Limit, AC Mains Under / Over Voltage Shut Off, Peak Current Limit, Over Temp

Amps

Watts

BTU / hr (Note 4)

All other Trademarks are property of their respective owners. No endorsement is implied. Due to continual product development, specifications are subject to change without notice. ATS005609 RevC 3/19

1601 JACK MCKAY BLVD. ENNIS, TEXAS 75119 U.S.A.

TELEPHONE: (800) 876-3333 SUPPORT@ATLASIED.COM

AtlasIED.com

Agency Approvals

North America Agency ETL

Testing Standard North America 60065

FCC Class A (Conducted & Radiated Emissions) Part 15 of the FCC Rules

CE Yes (Includes RoHS & WEEE)

Optional Accessories

HPA-DAC2 - Dante™ Digital Audio Interface Two-Channel Receive (Only) - Field Installable

NOTES:

1. Power level measurment is define as follows: 1Hz Sine wave signal burst of 20 cycles (20mS) at 1% THD+N, followed by 480 cycles of a 1kHz sine wave at 10% of the max power. Other power measurements are available upon requests.

2. Power measurement with Ethernet connected. Without Ethernet connected deduct .2W

3. Average Power is defined as Pink Noise input signal applied to achieve 1/4 of the 4 Ohm or 70.7V power rating.

4. Max Power is defined as 1 KHz input signal applied to achieve the maxium power output before clipping into a 4 Ohm or 70.7V load.

5. BTU is calcualed by the AC Mains Power consumed minus the total power output measured at the specified load and condition, multiplied by 3.412.

Example: 785 Watts from the AC Source - 600 Watts Total Output power = 185 x 3.412 = 631 BTU

All other Trademarks are property of their respective owners. No endorsement is implied. Due to continual product development, specifications are subject to change without notice. ATS005609 RevC 3/19

1601 JACK MCKAY BLVD. ENNIS, TEXAS 75119 U.S.A.

TELEPHONE: (800) 876-3333 SUPPORT@ATLASIED.COM

AtlasIED.com

0

9.30

10.30

19.00

3.50

0

9.30

10.30

FRONT

SIDE

HPA602

Multi-Impedance Ampliﬁer

Protect

Limit

Signal

Ready

Power

Temp

Standby

1

0 1020 10

Dimensional Drawings

19.00

3.50

1601 Jack McKay Blvd. • Ennis, TX 75119

RISC OF ELECTRIC SHOCK

WARNING: SHOCK HAZARD - DO NOT OPEN

AVIS: RISQUE DE CHOC ELÉCTRIQUE - NE PAS OUVRIR

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK

DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE

AVIS: NE PAS EXPOSER CE MATÉRIEL À LA PLUIE OU L’HUMIDITE

AFIN DE REDUIRE LE RISQUE D’INFLAMMATION OU DE CHOC ELÉCTRIQUE

800.876.3333 • AtlasIED.com

CAUTION

RISQUE D’ELÉCTROCUTION

DO NOT OPEN

Protect

Signal

Ready

1

0 1020 10

ATTENTION

NE PAS OUVRIR

APPARATETS STIKPROP SKAL TILSLUTTES EN STIKKONTAKT MED JORD,

Limit

SOM GIVER FORBINDELSE TIL STIKPROPPENS JORD.

LAITE ON LIITETTÄVÄ SUOJAKOSKETTIMILLA

VARUSTETTUUN PISTORASIAAN.

APPARATET MÅ TILKOPLES JORDET STIKKONTAKT.

APPARATEN SKALL ANSLUTAS TILL JORDAT UTTAG.

Power

Temp

Standby

17.00

Serial Number

Place Label Here

HPA602

Multi-Impedance Ampliﬁer

CONFORMS TO ANSI/UL STD. 60065 CERTIFIED TO CAN/CSA STD. C22.2 No. 60065

5002632

All other Trademarks are property of their respective owners. No endorsement is implied. Due to continual product development, specifications are subject to change without notice. ATS005609 RevC 3/19

1601 JACK MCKAY BLVD. ENNIS, TEXAS 75119 U.S.A.

0

9.30

10.30

TELEPHONE: (800) 876-3333 SUPPORT@ATLASIED.COM

AtlasIED.com

Optional Accessories

HPA-DAC2 - Dante™ Two-Channel Receiver Card

Architect and Engineer Specications

The power amplifier shall be a two-channel multi-impedance amplifier capable of driving 100V, 70.7V, 8Ω, and 4Ω load conditions. The amplifier shall have multiple internal circuits to protect itself and connected speakers from Input RF, output DC, output short circuits, current overload, clipping, AC mains under or over voltage, peak current limit, and thermal overload. A variable speed fan shall provide rear to front airflow for dynamic cooling. The universal PFC switch mode 50/60Hz power supply operating range shall be 95V-264V. The AC Mains inlet shall be C15 IEC Locking Receptacle and ship with a IEC 16-guage 1.5M cord with a fixed NEMA 5-15 Male Plug. The HPA602 shall meet Energy Star 1W Standby Mode Standards. Power ratings shall equal or exceed 300W x 2 @ 100V, 70.7V, 8Ω and 4Ω loads. Each balanced Line input channel shall have a selectable input sensitivity of 0.775V, 1.0V, or 32dB, and frequency response shall be 20Hz-20kHz (+0/-1.5dB) with a Signal to Noise Ratio of >85dB below rated output (A-Weighted). Front panel indicators shall include ready, signal present, limiter, and protection LEDs. Front panel level controls shall be stepped attenuators with security covers included. Input terminations shall be removable 3.5mm Phoenix style connectors and loudspeaker outputs shall be a removable 4-position Phoenix style connector capable of accepting up to 8 AWG wire. A switch on the rear panel shall provide selection of stereo, parallel or bridge modes of operation. Rear panel 5 position Phoenix style GPIO ports shall provide Remote Turn On and Fault Reporting for each channel. The amplifier shall have one (1) rear mounted Accessory Card slot. This slot shall be for an HPA-DAC2, a two-channel Dante™ Digital Audio Receiver Input Card. Dimensions shall be 2 RU, 3.5" x 19" x 9.3" (89mm x483mm x 236mm) and the amplifier shall weigh 14.8 lbs (6.7kg).

The amplifier shall be AtlasIED HPA602.

All other Trademarks are property of their respective owners. No endorsement is implied. Due to continual product development, specifications are subject to change without notice. ATS005609 RevC 3/19

1601 JACK MCKAY BLVD. ENNIS, TEXAS 75119 U.S.A.

TELEPHONE: (800) 876-3333 SUPPORT@ATLASIED.COM

AtlasIED.com