Atlas IED FAP62T-UL2043 Installation Guide

16W @ 70.7V

FAP62TB

Full Range

Ceiling Material up to 2"

Tile Bridge

Auxiliary Suspension Point

Dogleg In Inverted Position

FAP62T

16W @ 70.7V

FA P62TB

Full Range

16W @ 70.7V

FA P62T-B

Full Range

16W @ 70.7V

FA P62T-B

Full Range

16W @ 70.7V

FAP62T-B

Full Range

16W @ 70.7V

FA P62T-B

Full Range

Ceiling Material up to 1-1/4"

Auxiliary Suspension Point

Tile Bridge

Ceiling Material up to 2"

Tile Bridge

Auxiliary Suspension Point

Dogleg In Normal Position

Dogleg In Inverted Position

Ta p Wa ttage Total: 64 Wa tts

Typical 120 Watt 70.7V Output

Typical Parallel Hookup of Full Range 70.7/100V Speakers

Amplifier

Input

-

+

-

+

-

+

-

+

-

+

16W @ 70.7V

FAP62TB

Full Range

Ceiling Material up to 1-1/4"

Auxiliary Suspension Point

Tile Bridge

Ceiling Material up to 2"

Tile Bridge

Auxiliary Suspension Point

Dogleg In Normal Position

Dogleg In Inverted Position

Installation Instructions

The Atlas Sound Strategy Series

®

II assembly mounts easily into existing

construction drop ceiling or drywall materials.

ATS001131 RevF 12/08

FAP62T

Installation Instructions

ATS001131 RevD 5/08

Mounting Template

11" Diameter

3. Bring service loop from rear of tile, through the tile bridge / C-ring to access panel located on the side of the enclosure. Terminate service loop to Phoenix style

4. Insert enclosure into hole. Using standard #2 Phillips screwdriver or screw-gun, tighten four dogleg assemblies until they engage the C-ring assembly.

Use of optional FAP62-TR1 (for use with FAP62T) new construction bracket essentially reserves a speaker mounting location prior to drywall installation

1. Bring service loop through hole in ceiling provided by pre-construction bracket to access panel located on side of the enclosure. Terminate service

2. Insert speaker assembly into hole. Using standard #2 Phillips screwdriver or screw-gun, tighten four dogleg assemblies until they engage the ring provided

Drop Tile Ceiling

101⁄2" Diameter

Installation

1. Remove 2' x 2' or 2' x 4' tile.

2. Align adjustable dual rail & C-ring assembly on rear of tile in desired position.

3. Using the template provided, mark cut out circle with marker and cut hole.

(11" FAP62T)

4. Affix C-ring assembly to rails using screws provided and position assembly on rear of ceiling tile.

Replace tile into grid. Be sure formed ends of tile bridge rails engage T-bar tile support rails.

5. Bring service loop from rear of tile, through the tile bridge/C-ring to the access panel located on side of enclosure.

Terminate the service loop to Phoenix style connector provided (please note polarity).

Combination knockouts are provided to facilitate conduit.

6. Insert enclosure through front of tile. Using standard #2 Phillips screwdriver or screw-gun, tighten four dogleg assemblies

until they engage the C-ring assembly. DO NOT OVER-TIGHTEN DOGLEG SCREWS!

7. Adjust front mounted switch to desired wattage tap setting or 8Ω* (See important note regarding 8Ω operation)

8. Install press-fit grille into front bezel ring. Push baffle upwards until it is flush with the bezel ring.

9. For safety and seismic considerations a suspension ring is integrated into the input panel section of unit.

Atlas Sound strongly suggests that a support wire be installed from this support point to a suitable anchor point above ceiling grid.

In drop tile applications, this wire can usually be installed from an adjacent tile access near speaker location.

Dry Wall ("Hard Deck") Installation

1. Using the template provided, mark cut out circle in desired mounting location and cut hole. (11" FAP62T)

2. Place tile bridge rails and C-ring through hole. Use V-shaped edge of C-ring to align tile bridge assembly above ceiling

(alignment screws provided are not required for this type of installation)

connector provided (please note polarity). Combination knockouts are provided to facilitate conduit.

DO NOT OVER-TIGHTEN DOGLEG SCREWS!

5. Adjust front mounted switch to desired wattage tap setting or 8Ω* (See important note regarding 8Ω operation)

6. Install press-fit grille into front bezel ring. Push baffle upwards until it is flush with the bezel ring.
New Construction (Drywall Ceilings)

in new construction. Bracket mounts between 16" or 24" OC studs and includes a 3⁄8" downward lip to provide a template for drywall installers to cut

around. For final installation, please follow these instructions:

Note: Tile bridge components are not used in new construction applications where new construction bracket is utilized.

loop to Phoenix style connector provided (please note polarity). Combination knockouts are provided to facilitate conduit.

on the new construction bracket. DO NOT OVER-TIGHTEN DOGLEG SCREWS!

3. Adjust front mounted switch to desired wattage tap setting or 8Ω* (See important note regarding 8Ω operation)

4. Install press-fit grille into front bezel ring. Push baffle upwards until it is flush with the bezel ring.

Painting Shield

1

FAP62-TR has not been evaluated by UL Laboratories

NOTE: Doglegs will accommodate ceiling material thickness up to 11⁄4" as shipped from factory. For thicker ceiling materials (up to 2") simply unscrew and flip doglegs

as shown. DO NOT OVER-TIGHTEN DOGLEGS IN EITHER CONFIGURATION!

NOTE: UL recognized conduit clamp must be used for conduit connections. Cable connection cavity is not intended to be used as a junction box.

NOTE: *DO NOT USE 8Ω SETTING WITH 70.7V / 100V SYSTEMS! *DO NOT OVERPOWER IN 8Ω CONFIGURATION!

AMPLIFIER OUTPUT SHOULD NOT EXCEED 32 W RMS @ 8Ω PER SPEAKER

FREQUENCY RESPONSE: 90Hz - 20kHz SENSITIVITY: 88dB (1W / 1M)