Atec Agilent-E7401A, Agilent-E74002A, Agilent-E74003A, Agilent-E74004A, Agilent-E74005A User Manual

These specifications apply to the Agilent Technologies E7401A,
E7402A, E7403A, E7404A and E7405A EMC analyzers.

Specifications

All specifications apply over 0° C to +55° C unless otherwise
noted and are covered by the product warranty. The analyzer will
meet its specifications when: it’s within the one year calibration
cycle, AUTO ALIGN [ALL] is selected, stored a minimum 2 hours
within the operating temperature range, turned on for at least 5
minutes, and Align Now RF has been run once every 24 hour period.
Typical performance describes the level at which 80% of the units will
meet or exceed with a 95% confidence level over 20 to 30° C, but is
not covered in the product warranty. Characteristics describe
expected product performance levels that are not covered in the
product warranty.

Frequency specifications
Frequency range

E7401A

50 Ω 9 kHz to 1.5 GHz

E7402A 9 kHz to 3.0 GHz

dc coupled 30 Hz

6

to 3.0 GHz

ac coupled 100 kHz6to 3.0 GHz

E7403A

dc coupled 9 kHz to 6.7 GHz
dc coupled (Option UKB) 30 Hz6to 6.7 GHz
ac coupled 100 kHz to 6.7 GHz
Band
0 9 kHz to 3.0 GHz
1 2.85 GHz to 6.7 GHz

E7404A

dc coupled 9 kHz to 13.2 GHz
dc coupled (Option UKB) 30 Hz6to 13.2 GHz
ac coupled 100 kHz to 13.2 GHz
Band LO harmonic = N
0 1- 9 kHz to 3.0 GHz
(Option UKB) 30 Hz6to 3.0 GHz
1 1- 2.85 GHz to 6.7 GHz
2 2- 6.2 GHz to 13.2 GHz

E7405A 9 kHz to 26.5 GHz

Band LO harmonic = N
0 1- 9 kHz to 3.0 GHz
0 (Option UKB) 30 Hz6to 3.6 GHz
1 1- 2.85 GHz to 6.7 GHz
2 2- 6.2 GHz to 13.2 GHz
3 4- 12.8 GHz to 19.2 GHz
4 4- 18.7 GHz to 26.5 GHz

Frequency reference (Option 1D5)

Aging ±2 x 10-6/year ±1 x 10-7/year
Temperature stability ±5 x 10

-6

±1 x 10

-8

Settability ±5 x 10

-7

±1 x 10

-8

Frequency readout accuracy

(start, stop, center, marker) ±(frequency indication

x frequency reference error

1

+ span accuracy + 15% of RBW
+ 10 Hz) + 1 Hz x N

4

Marker frequency counter

2

Accuracy

3

±(marker frequency x frequency
reference error1+ counter resolution)

Counter Resolution Selectable from 1 Hz to 100 kHz

Frequency span

Range 0 Hz (zero span), 100 Hz x N4to

the range of the spectrum analyzer

Resolution 2 Hz x N

4

Accuracy (> 2000 sweep points)

Sweep type linear ±0.5% of span
Sweep type log ±2% of span (characteristic)

Agilent

E7400 A-series EMC Analyzers

Data Sheet

Manufacturers > Agilent Technologies
Categories > EMC Test Equipment > Conducted \ Radiated Emissions Test > EMI Analyzers \ EMC Receivers

Agilent E7405A EMC Analyzer Product Page

How-To Video

2

Sweep time

Range

Span > 0 Hz 1 ms to 4000 s
Span = 0 Hz 10 µs15to 4000 s

(Option AYX) 50 ns15to 4000 s
Accuracy ±1%
Sweep trigger Free run, single, line, video,

external, delay, offset, and gate
(Option 1D6)

Delay trigger range 1 µs to 400 s

Sweep (trace) point range 101 to 8192

Span = 0 Hz 2 to 8192

Resolution bandwidth 10 Hz to 3 MHz (-3 dB) in

1-3-10 sequence

16

5 MHz (-3 dB) bandwidth
200 Hz

16,

9 kHz, 120 kHz, 1 MHz

(-6 dB) EMI bandwidths

1 MHz (impulse) EMI bandwidth

Option 1D5 Adds 1 Hz and 3 Hz
Accuracy

10 Hz to 300 MHz (-3 dB) ±10%

1Hz and 3 Hz (Option 1D5) ±10%

1 kHz to 3 MHz (-3 dB) ±15%

5 MHz (-3 dB) ±30%

200 Hz (-6 dB) ±10%

9 kHz to 120 kHz (-6 dB) ±20%

1 MHz (-6 dB) ±10%

1 MHz (impulse) ±15%
Selectivity (characteristic)

10 Hz to 300 Hz (-3 dB) < 5:1 (-60 dB/-3 dB)

(Digital, approximately Gaussian-shaped)

1 kHz to 3 MHz (-3 dB) < 5:1 (-60 dB/-3 dB)

(approximately Gaussian-shaped)

200 Hz (-6 dB) < 3:1 (-40 dB/-6 dB)

(Digital, Kaizer Windows)

9 kHz, 120 kHz,

1 MHz (-6 dB) < 10:1 (-60 dB/-6 dB)

(approximately Gaussian-shaped)

1 MHz (impulse) < 10:1 (-60 dB/-6 dB)

(approximately Gaussian-shaped)

Video bandwidth range 30 Hz to 3 MHz6in 1-3-10

sequence
1, 3, 10 Hz for RBW’s < 1 kHz

Stability

Noise sidebands (1 kHz RBW, 30 Hz VBW and sample detector)

E7401A

≥ 1 kHz na ≤ 79 dBc/Hz

(Option 1D5)
≥ 10 kHz ≤ -93 dBc/Hz ≤ -95 dBc/Hz
> 20 kHz ≤ -100 dBc/Hz ≤ -102 dBc/Hz
> 30 kHz ≤ -104 dBc/Hz ≤ -106 dBc/Hz
> 100 kHz ≤ -113 dBc/Hz ≤ -116 dBc/Hz

E7402/03/04/05A

≥ 1 kHz na ≤ 78 dBc/Hz

(Option 1D5)
≥ 10 kHz ≤ -90 dBc/Hz

21

≤ -94 dBc/Hz

21

> 20 kHz ≤ -100 dBc/Hz

21

≤ -105 dBc/Hz

21

> 30 kHz ≤ -106 dBc/Hz

21

≤ -112 dBc/Hz

21

> 100 kHz ≤ -119 dBc/Hz

21

≤ -122 dBc/Hz

21

> 1 MHz ≤ -125 dBc/Hz

21

≤ -127 dBc/Hz

21

> 5 MHz ≤ -127 dBc/Hz

21

≤ -129 dBc/Hz

21

> 10 MHz ≤ -131 dBc/Hz

21

≤ -136 dBc/Hz

21

Residual FM

1 kHz RBW, 1 kHz VBW ≤ 150 x N4Hz pk-pk in 100 ms
Option 1D5 ≤ 100 x N4Hz pk-pk in 100 ms
10 Hz RBW, 10 Hz VBW ≤ 2 x N4Hz pk-pk in 20 ms

System-related sidebands

≥ 30 kHz offset from CW signal ≤ -65 dBc + 20 Log N

4

Amplitude specifications
Amplitude range

Measurement range Displayed average noise level (DANL)

to maximum safe input level

Input attenuator range

E7401A 0 to 60 dB, in 5 dB steps
E7402A, 03A, 04A 0 to 65 dB (75 dB6), in 5 dB steps
E7405A 0 to 65 dB, in 5 dB steps

-70

Typical performance
Spec

-90

dBc/Hz

-110

-130
1k 10k 100k 1M

Offset (Hz)

3

Maximum safe input level

Average continuous power

E7401A (input attenuator ≥15 dB)

+30 dBm (1 W)
(input attenuator ≥5 dB)

E7402A/03A/04A/05A +30 dBm (1 W)

Peak pulse power (input attenuator ≥30 dB)

E7402A/03A/04A/05A +50 dBm (100 W)
E7401A +30 dBm (1 W)

dc

E7401A, E7402A 100 Vdc
E7402A (Option UKB) 0 Vdc (dc coupled)

50 V (ac coupled)

E7403A, E7404A 0 Vdc (dc coupled)

50 V (ac coupled)

E7405A 0 Vdc

(Option UKB) 0 Vdc (dc coupled)

50 V (ac coupled)

1 dB gain compression (total power at input mixer5)

≥ 50 MHz 0 dB
≥ 6.7 GHz -3 dB
≥ 13.2 GHz -5 dB

Displayed average noise level (dBm)
(Input terminated, 0 dB attenuation, sample-detector)
1 kHz RBW; 30 Hz VBW
10 Hz RBW; 1 Hz VBW
1 Hz RBW; 1 Hz VBW (Option 1D5)

1 kHz 10 Hz 1 kHz 10 Hz 1 Hz
RBW RBW w/preamp w/preamp Option 1D5

on on, typical w/preamp

on, typical

E7401A

400 kHz to 10 MHz ≤ -115 ≤ -134 ≤ -150 ≤ -155 ≤ -165
10 MHz to 500 MHz ≤ -119 ≤ -138 ≤ -154 ≤ -156 ≤ -166
500 MHz to 1 GHz ≤ -117 ≤ -136 ≤ -152 ≤ -156 ≤ -166
1 GHz to 1.5 GHz ≤ -114 ≤ -133 ≤ -150 ≤ -155 ≤ -165

E7402A

30 Hz to 9 kHz

22

(Option UKB) na ≤-93 na na na
9 kHz to 100kHz22na ≤-109 na na na
100 kHz to 1 MHz22na ≤-135 na na na
1 MHz to 10 MHz22≤-117 ≤-136 na ≤-152 ≤-162
10 MHz to 1 GHz ≤-117 ≤-136 ≤-15219≤-156 ≤-166
1 GHz to 2 GHz ≤-116 ≤-135 ≤–15319≤-156 ≤-166
2 GHz to 3 GHz ≤-114 ≤-133 ≤–15119≤-154 ≤-164

E7403A, 04A, 05A

30 Hz to 9 kHz

22

(Option UKB) na ≤ -93 na na na
9 kHz to 100kHz22na ≤ -1096na na na
100 kHz to 1 MHz22na ≤ -1356na na na
1 MHz to 10 MHz22≤ -1176≤ -1376na ≤ -155 ≤ -165
10 MHz to 1 GHz ≤ -116 ≤ -135 ≤ -15119≤ -157 ≤ -167
1 GHz to 2 GHz ≤ -116 ≤ -131 ≤ –15119≤ -155 ≤ -165
2 GHz to 3 GHz ≤ -112 ≤ -131 ≤ –14919≤ -152 ≤ -162
3 GHz to 6 GHz ≤ -112 ≤ -131 na ≤ -138 na
6 GHz to 12 GHz ≤ -111 ≤ -130 na ≤ -137 na
12 GHz to 22 GHz ≤ -107 ≤ -126 na ≤ -134 na
22 GHz to 26.5 GHz ≤ -106 ≤ -125 na ≤ -132 na

Display range

Log Scale 0.1, 0.2, 0.5 dB/division and 1 to 20 dB/division

in 1 dB steps; ten divisions displayed

RBW ≥ 1kHz 0 to -85 dB from reference level is calibrated

RBW ≤ 300 kHz 0 to -120 dB from reference level is calibrated
Linear scale 10 divisions
Scale units dBm, dBmV, dBµV, dBµA, Amps, Volts and Watts

Marker readout resolution

Log scale

0 to -85 dB 0.04 dB
0 to -120 (RBW ≤ 300 Hz 0.04 dB

Linear scale 0.01% of reference level

Fast sweep times for zero span (Option AYX)
Log Scale

0 to -85 dB 0.3 dB

Linear 0.3 dB of reference level

Frequency response (10 dB input attenuation)

Absolute7Typical Relative

flatness

8

E7401A

9 kHz to 1.5 GHz ±0.5 dB na ±0.5 dB

E7402A/03A/04A/05A

30 Hz to 3 GHz

6

(Option UKB) ±0.5 dB na ±0.5 dB

9 kHz to 3 GHz ±0.46 dB ±0.14 dB ±0.5 dB

3.0 GHz to 6.7 GHz ±1.5 dB ±0.39 dB ±1.3 dB

6.7 GHz to 13.2 GHz ±2.0 dB ±0.68 dB ±1.8 dB

13.2 GHz to 26.5 GHz ±2.0 dB ±0.86 dB ±1.8 dB

Input attenuation switching uncertainty at 50 MHz

Attenuation setting

0 dB to 5 dB ±0.3 dB
10 dB Reference
15 dB ±0.3 dB
20 to 60 dB (E7401A) ±(0.1 dB + 0.01 x attenuator setting)
20 to 65 dB ±(0.1 dB + 0.01 x attenuator setting)

Absolute amplitude accuracy Typical

At reference settings

13

±0.34 dB ±0.13 dB
E7401A ±0.30 dB ±0.10 dB
Preamp on

16

±0.37 dB ±0.14 dB

Overall amplitude accuracy9±(0.54 dB + absolute

frequency response)

4

RF input VSWR6(at tuned frequency, 10 dB attenuation)

E7401A

1 MHz to 1.5 GHz 1.35:1

E7402A

100 Hz to 100 kHz 1.1:1 (Option UKB)
9 kHz to 100 kHz 2:1
100 kHz to 3 GHz 1.4:1

E7403A/04A

100 Hz to 100 kHz 1.1:1 (Option UKB)
9 kHz to 100 kHz 2:1
100 kHz to 6.7 GHz 1.3:1

6.7 kHz to13.2 GHz 1.5:1

E7405A

100 Hz to 100 kHz 1.1:1 (Option UKB)
9 kHz to 6.7 GHz 1.3:1

6.7 GHz to 13.2 GHz 1.5:1

13.2 GHz to 22 GHz 2:1
22 GHz to 26.5 GHz 2.2:1

Resolution bandwidth switching uncertainty

(Referenced to 1 kHz RBW, at reference level)
10 Hz to 3 MHz RBW ±0.3 dB
5 MHz RBW ±0.6 dB
10 Hz to 300 Hz RBW ±0.3 dB

Reference level

Range -149 dBm to maximum mixer level

+ attenuator setting

Resolution

Log scale ±0.1 dB
Linear scale ±0.12% of reference level

Accuracy (reference level ±0.3 dB (-10 dBm to –60 dBm)

-attenuator setting ±0.5 dB (-60 dBm to –85 dBm)
+ preamp gain) ±0.7 dB (-85 dBm to –90 dBm)

Display scale fidelity

Log maximum cumulative

RBW ≥ 1 kHz

dB below reference level Typical

0 dB (reference) ±0.00 dB ±0.00 dB
> 0 dB to 10 dB ±0.3 dB ±0.08 dB
> 10 dB to 20 dB ±0.4 dB ±0.09 dB
> 20 dB to 30 dB ±0.5 dB ±0.10 dB
> 30 dB to 40 dB ±0.6 dB ±0.23 dB
> 40 dB to 50 dB ±0.7 dB ±0.35 dB
> 50 dB to 60 dB ±0.7 dB ±0.35 dB
> 60 dB to 70 dB ±0.8 dB ±0.39 dB
> 70 dB to 80 dB ±0.8 dB ±0.46 dB
> 80 dB to 85 dB ±1.15 dB ±0.79 dB

RBW ≤ 300 Hz (Span >0 Hz)

0 dB to 98 dB ±(0.3 dB + 0.01 x dB from

reference level)

≥ 98 dB to 120 dB ±(2.0 dB from reference level)

6

Log incremental accuracy

0 dB to 80 dB ±0.4 dB/4 dB from reference level

Linear accuracy ± 2% of reference level

Linear to log switching ±0.15 dB at reference level

Spurious responses

Second harmonic distortion
E7401A

2 MHz to 750 MHz < -75 dBc for -40 dBm tone at

input mixer

5

E7402A/03A/04A/05A

10 MHz to 500 MHz < -65 dBc for -30 dBm tone at

input mixer

5

500 MHz to 1.5 GHz < -75 dBc for -30 dBm tone at

input mixer

2

1.5 GHz to 2.0 GHz < -85 dBc for -10 dBm tone at

input mixer

2

> 2.0 GHz < -100 dBc for -10 dBm tone at

input mixer5(or below displayed

average noise level)

Third order intermodulation distortion
E7401A

100 MHz to 1.5 GHz < -87 dBc for two -30 dBm tones at

input mixer5and > 50 kHz separation

E7402A/03A/04A/05A

100 MHz to 6.7 GHz < -85 dBc for two -30 dBm tones at

input mixer5and > 50 kHz separation
> 6.7 GHz < -75 dBc for two -30 dBm tones at

input mixer5and > 50 kHz separation

Other input related spurious

< -65 dBc, for -20 dBm tone at

input mixer

5

Residual responses (input terminated and 0 dB attenuation)
150 kHz to 6.7 GHz < -90 dBm

Amplitude ref. output

E7402A,03A,04A,05A
Amplitude -20 dBm (nominal)

FM demodulation

6

Input level -60 dBm + attenuator setting
Signal level 0 to -30 dB below reference level

Quasi-peak detector specifications

The EMC analyzer displays the quasi-peak amplitude of a pulse
radio frequency on continuous wave signals. Amplitude response
conforms with Publication 16 of Comite International Special des
Perturbations Radioelectrique (CISPR) Section 1, Clause 2.

5

Relative quasi-peak response to a CISPR pulse (dB)

Pulse repetition 120 kHz EMI BW 9 kHz EMI BW 200 Hz EMI BW
frequency (Hz) .03 to 1 GHz 0.150 to 30 MHz 9 kHz to 150 kHz

1000 +8.0 ±1.0 +4.5 ±1.0 –––
100 0 dB reference* 0 dB reference* +4.0 ±1.0
60 ––– ––– +3.0 ±1.0
25 ––– ––– 0 dB reference*
20 -9.0 ±1.0 -6.5 ±1.0 –––
10 -14 ±1.5 -10.0 ±1.5 -4.0 ±1.0
5 ––– ––– -7.5 ±1.5
2 -26 ±2.0 -20.5 ±2.0 -13.0 ±2.0
1 ––– -22.5 ±2.0 -17.0 ±2.0
Isolated Pulse ––– -23.5 ±2.0 -19.0 ±2.0

* Reference pulse amplitude accuracy relative a 66 µV CW signal < 1.5 dB as specified

in CISPR Pub 16 CISPR reference pulse: 0.44 µVs for 30 MHz to 1 GHz, 0.316 µVs for
150 kHz to 30 MHz, 13.5 µVs for 9 kHz to 150 kHz

General specifications
Temperature range

Operating 0° C to +55° C
Storage -40° C to +75° C

EMI compatibility Conducted and radiated emissions is

in compliance with CISPR Pub.
11/1990 Group 1 Class B

14

Audible noise < 40 dBa pressure and < 4.6 Bels

power (ISODP7779)

Military specification Type tested to the environmental

specifications of MIL-PRF-28800F,
class 3

Power requirements

ON (line1) 90 to 132 V rms, 47 to 440 Hz

195 to 250 V rms, 47 to 66 Hz

Power consumption < 300 W
Standby (line 0) Power consumption < 5 W
DC operation

Voltage 12 to 20 Vdc
Power consumption < 200 W

Measurement speed

E7401A E7402A E7403A/04A/05A

Local measurement rate10≥ 50/sec ≥ 45/sec ≥ 40/sec
Remote measurement as

GPIB transfer rate

11

≥ 45/sec ≥ 45/sec ≥ 40/sec

RF center frequency
tuning time

18

≥ 75/ms ≥ 75/ms ≥ 75/ms

Data storage (nominal)

Internal 200 traces17or states
External (floppy) 200 traces17or states

Weight (without options)

E7401A 12.6 kg (27.7 lbs.)
E7402A 14.9 kg (32.9 lbs.)
E7403A/04A/05A 17.1 kg (37.7 lbs.)

Dimensions

without handle 222 mm(H) x 409 mm(D)

x 373 mm(W)

with handle (max.) 222 mm(H) x 516 mm(D)

x 416 mm(W)

Inputs/outputs

Front panel connectors

Input 50 Ω type N (f)

Option BAB 50 Ω APC 3.5 (m)

RF Out 50 Ω type N (f)

Probe power +15 Vdc, -12.6 Vdc at 150 mA

max. characteristic

Ext. keyboard 6-pin mini-DIN, PC keyboards

(for entering screen titles and
file names)

Speaker front-panel knob controls volume

Headphone 3.5 mm (1/8

inch) miniature audio jack

Power output 0.2 W into 4 Ω

6

Amptd ref. output 50 Ω, BNC (f)

E7402A/03A/04A/05A

Rear panel connectors
10 MHz ref out 50 Ω, BNC (f), > 0 dBm

6

10 MHz ref in 50 Ω, BNC (f), -15 to +10 dBm

6

Gate trig/ext. trig in BNC (f), 5 V TTL

Gate hi swp out BNC (f), 5 V TTL

VGA output VGA compatible monitor, 15-pin

D-SUB, (31.5 kHz horizontal, 60 Hz
vertical sync rates, non-interlaced)
Analog RGB 640 x 480

Option AJ4 (IF and Sweep Ports) or Option AYX

Aux IF output BNC (f), 21.4 MHz, nominal -10 to

-70 dBm

6

(uncorrected)
Aux video out BNC (f), 0 to 1 V6(uncorrected)
Hi swp In BNC (f), low stops sweep

(5 V TTL)
Hi swp out BNC (f), (5 V TTL)
Swp out BNC (f), 0 to +10 V6ramp

6

GPIB interface

Standard (Option AH4) IEEE-488 bus connector

Serial interface

(Option 1AX) RS-232, 9-pin D-SUB (m)

Parallel interface

Standard 25-pin D-SUB (f), printer port only

Option specifications

Option 1DN tracking generator
Frequency range

E7401A
Option 1DN 9 kHz to 1.5 GHz
E7402A/03A/04A/05A
Option 1DN 9 kHz to 3.0 GHz

Output power level range

Range
E7401A

Option 1DN 0 to -70 dBm

E7402A/03A/04A/05A

Option 1DN -2 to -66 dBm
Resolution 0.1 dB
Absolute Accuracy (at 50 MHz)

Option 1DN ±0.75 dB

Output vernier range

E7401A 10 dB
E7402A/03A/04A/05A 8 dB

Output attenuator range

E7401A 0 to 60 dB, 10 dB steps
E7402A/03A/04A/05A 0 to 56 dB, 8 dB steps

Output flatness

E7401A

Option 1DN

9 kHz to 10 MHz ±2.0 dB

10 MHz to 1.5 GHz ±1.5 dB
E7402A/03A/04A/05A

Option 1DN

9 kHz to 10 MHz ±3.0 dB

10 MHz to 3.0 GHz ±2.0 dB

Effective source match (characteristic)
E7401A < 2.5:1
E7402A/03A/04A/05A < 2.0:1 (0 dB Atten.)

< 1.5:1 (≥ 8 dB Atten.)

Spurious output

Harmonic spurs
E7401A

(0 dBm output)
9 kHz to 20 MHz <-20 dBc
20 MHz to 1.5 GHz <-25 dBc

E7402A/03A/04A/05A

(-1 dBm output)

9 kHz to 3 GHz <-25 dBc
Non-harmonic spurs
E7401A <-35 dBc
E7402A/03A/04A/05A

9 kHz to 2 GHz <-27 dBc

2 GHz to 3 GHz <-23 dBc

Dynamic range

Maximum output power – displayed average noise level

Power sweep range

E7401A

Option 1DN (-15 dBm to 0 dBm) – (source

attenuator setting)

E7402A/03A/04A/05A

Option 1DN (-10 dBm to -1 dBm) – (source

attenuator setting)

Preamplifier (standard)

E7401A 100 kHz to 1.5 GHz
E7402A/03A/04A/05A 1 MHz to 3 GHz
(nominal gain 20 dB)

7

1. Frequency reference error = (aging rate x period of time since adjustment +
settability + temperature stability)

2. Not available in RBW < 1kHz

3. Marker level to DANL > 25 dB, Span ≤ 1.5 GHz, RBW/Span ≥ 0.002

4. N = LO harmonic mixing mode

5. Mixer power level (dBm) = input power (dBm) – input attenuator (dB)

6. Characteristic

7. Referenced to 50 MHz amplitude reference (20° C – 30° C)

8. Reference to midpoint between highest and lowest frequency response
deviations. (20° C – 30° C)

9. For reference levels 0 to 50 dBm; input attenuation 10 dB; dc coupled;
RFW 1 kHz; VBW 1 kHz; scale loge range 0 to -50 dB from reference level;
sweeptime coupled; signal input 0 to 50 dB; spsn ≤ 20 kHz.

10. Characteristic; factory preset, fixed center frequency, sweep points = 101
auto align off, RBW = 1 MHz, stop frequency ≤ 3 GHz, span > 10 MHz and
≤ 600 MHz (E4401, span > 102 MHz and ≤ 400 MHz).

11. Characteristic; factory preset, fixed center frequency, sweep points = 101 auto
align off, RBW = 1 MHz, stop frequency ≤ 3 GHz, span = 20 MHz, GPIB
interface, display and markers off, fixed center frequency, single sweep

12. In time domain sweeps

13. Reference level -25 dBm (E7401A) or -20 dBm (E7402A/03A/04A/05A);
input attenuation 10 dB; center frequency 50 MHz; RBW 1 kHz; VBW 1 kHz;
scale linear or log; span 2 kHz; sweep time coupled, sample director, signal at
reference level.

14. Meets Class A performance during dc operation or serial number
US41110000 or lower.

15. RBW ≥1 kHz, 2 sweep points

16. 10 Hz to 300 Hz are only available in spans of ≤ 5 MHz and are not usable
with tracking generator Option 1DN.

17. When storing a 401-point trace plus the instrument state

Agilent Technologies’ Test and Measurement Support,
Services, and Assistance

Agilent Technologies aims to maximize the value you receive,
while minimizing your risk and problems. We strive to ensure
that you get the test and measurement capabilities you paid for
and obtain the support you need. Our extensive support
resources and services can help you choose the right Agilent
products for your applications and apply them successfully.
Every instrument and system we sell has a global warranty.
Support is available for at least five years beyond the produc­tion life of the product. Two concepts underlie Agilent's overall
support policy: "Our Promise" and "Your Advantage."

Our Promise

Our Promise means your Agilent test and measurement equip­ment will meet its advertised performance and functionality.
When you are choosing new equipment, we will help you with
product information, including realistic performance specifica­tions and practical recommendations from experienced test
engineers. When you use Agilent equipment, we can verify that
it works properly, help with product operation, and provide
basic measurement assistance for the use of specified capabili­ties, at no extra cost upon request. Many self-help tools are
available.

Your Advantage

Your Advantage means that Agilent offers a wide range of addi­tional expert test and measurement services, which you can
purchase according to your unique technical and business
needs. Solve problems efficiently and gain a competitive edge
by contracting with us for calibration, extra-cost upgrades, out­of-warranty repairs, and on-site education and training, as well
as design, system integration, project management, and other
professional engineering services. Experienced Agilent engi­neers and technicians worldwide can help you maximize your
productivity, optimize the return on investment of your Agilent
instruments and systems, and obtain dependable measurement
accuracy for the life of those products.

By internet, phone, or fax, get assistance with all your
test and measurement needs

Online assistance:
www.agilent.com/find/assist

Phone or Fax

United States:

(tel) 1 800 452 4844

Canada:

(tel) 1 877 894 4414
(fax) [phone]

China:

(tel) 800-810-0189
(fax) 1-0800-650-0121

Europe:

(tel) (31 20) 547 2323
(fax) (31 20) 547 2390

Japan:

(tel) (81) 426 56 7832
(fax) (81) 426 56 7840

Korea:(tel) (82-2) 2004-5004
(fax) (82-2) 2004-5115

Latin America:

(tel) [phone]
(fax) [phone]

Taiwan:

(tel) 080-004-7866
(fax) (886-2) 2545-6723

Other Asia Pacific
Countries:

(tel) (65) 375-8100
(fax) (65) 836-0252
Email: [e-mail]

Product specifications and descriptions in this
document subject to change without notice.

© Agilent Technologies, Inc. 2001
Printed in USA, October 29, 2001

5968-3662E