No part of this manual, including the products and software described in it, may be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except
documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK
Computer Inc. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless such
repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the product is
defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE
LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR
LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF
ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS
MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE
ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A
COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES
THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights
of their respective companies, and are used only for identication or explanation and to the owners’ benet,
without intent to infringe.
Other Eects10-band Equalier/27 Environment Eects
ASIO 2.0 Driver SupportSupports 44.1K/48K/96K/192KHz @16/24bit with
very low latency
Specications are subject to change without notice.
8Chapter 1: Product introduction
ENGLISH
Essence STX II card layout
I/O ports
Front right RCA output. Connect to the right input of the 2/2.1-channel speakers of
your system.
Front left RCA output. Connect to the left input of the 2/2.1-channel spearkers of your
system.
Amplied 6.3mm (1/4") headphone output. Connect to your headphones/headsets.
ENGLISH
• To prevent possible damage, please set up the compatible gain in audio center or mute the
volume before powering up.
• DO NOT connect your speakers to the headphone output port. The possible high driving
power may cause damage to your speakers.
6.3mm analog input (Line-in/Mic-in). Connect to your microphone with builtin microphone amplier or audio devices with line output such as MP3 player or
synthesizer.
S/PDIF coaxial output: Connect to the external digital decoder, digital speaker
system, and home theater system, outputting digital audio including PCM, Dolby
Digital, DTS and WMA-pro.
PCI Express nger: Connect to a PCI Express slot on your motherboard.
ASUS Essence STX II9
ENGLISH
ENGLISH
Multi-channel expansion board bridge connector: Connect to the multi-channel
expansion board of Essence STX II 7.1 edition or Xonar H6.
4-pin Molex power connector: Connect to the power cable of your power supply
unit.
STX requires a 4-pin Molex connection to power the card.
Front panel audio header: Connect to the chassis-mounted audio module.
10Chapter 1: Product introduction
ENGLISH
Op-amps sockets
There are three swappable op-amp sockets in Essence STX II. Changing the op-amps aects the
tonal characteristics of the RCA outputs, while changing A and B aects the tonal characteristics of
the 6.3mm (1/4") headphone output.
A. Right channel I/V converters
B.. Left channel I/V converters
C. Low pass lter
To swap op-amps:
1. Use an IC clamp to clasp an op-amp and remove it vertically upwards.
2. Replace it with a new op-amp from the op-amp kit.
ENGLISH
To avoid reversion, ensure that the half-moon opening on the op-amp points the same way as
that on the socket.
ASUS Essence STX II11
ENGLISH
12Chapter 1: Product introduction
Chapter 2
2
Getting started
Before you proceed
Read the following notes and precautions before you install the audio card.
• Disable the onboard audio device in the BIOS settings or uninstall any sound cards on your
computer.
• For BIOS setting or uninstallation of other sound cards, refer to the user guides of your
motherboard and sound cards.
• Turn o your computer and disconnect all peripherals connected to it.
• Unplug the computer’s power cord from the power outlet.
• To avoid static electricity, use a grounded wrist strap or touch a safely grounded object such as
the metal part of the rear panel of your computer.
Installing the audio card
To install the audio card:
1. Unplug your computer's power cord and
disconnect all peripherals or cables.
2. Touch a metal object, such as the metal
side of your computer, to avoid damaging
components due to static electricity.
3. Remove the chassis cover.
4. Remove the expansion slot cover of an
available PCI Express slot.
5. Insert the card into the PCI Express slot until the card is seated rmly in place.
6. Secure the card into the slot with a screw.
7. Replace the chassis cover and reconnect all the cables.
8. Power on the computer.
ENGLISH
ASUS Essence STX II13
ENGLISH
Installing the audio card driver
After installing the ASUS Essence STX II to your computer, install the card driver from the bundled
CD or download from ASUS support site (http://support.asus.com).
• Essence STX II requires a 4-pin Molex connection to power the card. Connect it to your power
supply unit before installation.
• Driver version and the contents of the support CD are subject to change without notice.
To install the audio card driver:
1. Insert the driver CD into your optical drive. Proceed to step 5 if Autorun is enabled on your
computer and the driver setup screen appears. If Autorun is not enabled on your computer,
perform step 2.
2. On your Windows desktop, launch File Explorer.
• Windows® 7 SP1 Click Start then Computer.
• Windows® 8 Click + E
3. In File Explorer, double-click the optical drive icon.
4. Double-click Setup.exe.
5. Read through the End User License Agreement and click Accept when prompted. Follow
the onscreen instructions to complete the driver installation.
6. When driver installation is complete, you will be prompted to restart your computer.
14Chapter 2: Getting started
Chapter 3
Connecting speakers and peripherals
Connecting digital speaker systems (Home Theater)
Essence STX II supports DTS Interactive technologies, which transcode any audio, including games
and music, into industry-standard DTS surround bit-streams. This makes playback through your
home theater system possible, creating an immersive and impressive cinema surround sound
experience. A single digital cable connection can carry high-quality DTS digital audio from any of
your PC audio sources to any digital speakers or AV Receivers with DTS 5.1 decoding capabilities.
ENGLISH
Optical adapter. Plug the optical TOSLINK adapter into the S/PDIF-Out combo
connector.
Optical cable. Connect your decoder’s S/PDIF-In port to the optical adapter with the
TOSLINK optical cable.
You can also use a coaxial cable for a S/PDIF connection. Just plug the coaxial RCA male
connector to the S/PDIF-Out combo jack and connect the other end into the coaxial S/PDIF
input on your decoder.
ASUS Essence STX II15
Loading...
+ 33 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.