Astro 7600 User Manual
7600
WARNING
Study, understand and follow all instructions provided with this product.
Read these instructions carefully before installing, operating, servicing
or repairing this tool. Keep these instructions in a safe accessible place.
HOT STAPLE GUN KIT
FOR PLASTIC REPAIR
INTENDED USE OF THE TOOL
This Hot Staple Gun is designed to repair torn/damaged plastic
by heating and embedding special designed staples. Only use
staples which have been specially designed for this unit. Do not
use this tool outside of the designed intent. Never modify the tool
for any other purpose or use.
WARNING
• Normal use of this product is likely to expose the user to
dust and/or microscopic particles containing chemicals
known to the State of California to cause cancer, birth
defects or other reproductive harm. Always wear
appropriate safety equipment and clothing when using this
product. Study, understand and follow all instructions
provided with this product. Failure to read and follow all
warnings and operating instructions may result in damages
and serious injury or death.
• Always wear ANSI approved goggles when using this
product. (Users and Bystanders).
• Never use this tool for any application other than for
which it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
• Improper operation and/or maintenance of the tool,
modification of the tool, or use of the tool with accessories
not designed for it could result in serious injury or death.
• Always select the correct accessories of the correct size
and design for the job that you are attempting to perform.
• Always work in a clean, safe, well-lit, organized and
adequately equipped area.
• Do not begin repairs without assurance that vehicle is in
secure position, and will not move during repair.
HOT STAPLE GUN KIT FOR PLASTIC REPAIR
www.astrotools.com
1 YEAR LIMITED WARRANTY
• Astro Pneumatic Tool Co. warrants our products to the original user against defective
material or workmanship for a period of 1 year (except where noted on our price
schedule) from the date of 1st use. Astro reserves the right to determine whether the
product failed because of defective material, workmanship or other causes and to charge
back for missing parts. Astro Pneumatic Tool Co., at its discretion, will repair products
covered under this warranty free of charge. The distributor should direct the original user
to return the product (with the exceptions listed below) with the distributor’s name,
address, adequate proof of date of purchase or a copy of warranty card, and a short note
explaining the problem. Failures caused by accident, alteration, or misuse are not
covered by this warranty.
• If one part of this product fails, please do not return the entire product. Astro will
replace free of charge component parts of this product that fail within 1 year of first
use by the original user. Items included in this category include but are not limited
to kits, hand tool kits and any other product where there are multiple items or
components that make up the unit. Please contact the phone number below in
order to obtain the replacement components covered under warranty.
• Astro Pneumatic Tool Co. or its authorized service representatives must perform all
warranty repairs. Any repair to the product by unauthorized service representatives
voids this warranty. The rights under this warranty are limited to the original user and may
not be transferred to subsequent owners.
• This warranty is in lieu of all other warranties, expressed or implied, including warranties
of merchantability and fitness for a particular purpose. Some states do not allow the
exclusion of limitations of incidental or consequential damages so the
above limitations may not apply to you.
PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING
1-800-221-9705 FOR INSTRUCTIONS
Unpacking
When unpacking, check the parts diagram and part number
listing on page 3 to make sure all parts are included. If any
parts are missing or damaged, please call your distributor.
PRODUCT INFORMATION:
• Hot Staple Gun designed for quick repair and reinforcing
broken/ripped/damaged/split plastic on autos, motorcycles,
ATVs, boats, etc.
• Produces a strong durable repair while still leaving plastic
flexible enough for correct fit
• Unique Staple Gun heats special designed staples and
sets staples into plastic
• Repairs plastic components such as bumpers, headlight
fittings and assemblies, panel clips, tabs, plastic pins,
spoilers, etc.
• Easy to use, saves time and money
• Kit includes: Hot Staple Gun, Wire Cutter, Flip Screwdriver,
50pc each of “M”, “S”, “V” and “Z” Style Staples
• CSA Approved
• Patent pending
MADE IN CHINA
Page 1
DO NOT DISCARD – GIVE TO USER
7600
HOT STAPLE GUN KIT
FOR PLASTIC REPAIR
PRODUCT DESCRIPTION:
Generally when plastic products are broken and damaged
by impact, pressure or improper disassembly, they are
repaired by using resin glue or a plastic heat welder.
However, the sealing of the resin is unable to bear heavy
weight, while the heat welders easily deform the surface.
Therefore, most of the time when plastic products are
broken or damaged, people just throw them away and buy
new replacements. In fact, if you could repair the plastic
products efficiently you would increase your profits and
reduce the plastic waste which will make great contribution towards the overall environmental protection. Now the
Astro 7600 allows you to efficiently make those repairs.
FUNCTIONAL ADVANTAGES:
The Hot Staple Gun is suitable for repairing all kinds of
broken and damaged plastic products. It may restore the
broken or damaged part back to its original shape look
and strength.
The Hot Staple Gun inserts a staple into the plastic after it
has heated it in one easy step. The staple creates a
stronger reinforcement than the original part and it makes
it flexible so the part can be used again.
The Hot Staple Gun may adapt to the broken and damaged part to adjust for a proper fit of parts.
Step 5: Allow staple to cool and plastic to harden
around staple
Step 6: Clip excess staple ends
Step 7: Grind down excess cut staple ends (optional)
ALSO AVAILABLE SEPARATELY
Additional Staples Available:
Shape Image DescriptionModel #
50pc of “M” Style
7600M
7600S
Staples for repairing
outside corners
50pc of “S” Style
Staples for repairing
flat plastic areas
There are different shapes of staples for all kind of repairs,
and the nailing location are not limited to even surface; it
may also function on uneven surface or corners and even
round parts.
OPERATION INSTRUCTION:
Step 1: Align broken plastic part
Step 2: Heat staple by inserting into end of Hot Stapler
( - ) Low temperature position ( + ) High temperature position
Step 3: Once staple is heated press against plastic
Step 4: Set staple into plastic
7600V
7600Z
50pc of “V” Style
Staples for plastic
inside corners
50pc of “Z” Style
Staples for repairing
flat plastic areas that
need extra reinforcement
Page 2
Loading...