AS432
SEMICONDUCTOR 1.24V Precision Adjustable Shunt Reference/Amplifier
Features
¥Temperature-compensated: 50 ppm/¡C
¥0.25% to 2.0% bandgap offered
¥Internal amplifier with 150 mA capability
¥Multiple temperature ranges
¥Low frequency dynamic output impedance: < 150 m½
¥Low output noise
Description
The AS432 is a three terminal adjustable shunt regulator utilizing an accurate 1.24V bandgap reference. The AS432 is functionally similar to an AS431 except for its lower reference voltage, making it usable in a wide variety of low voltage applications.
Because of its robust bipolar technology, the AS432 handles a wide range of current, and holds off more than 18V so its use is not limited to low power, low voltage systems. Significant care has been taken to provide adequate AC bandwidth to allow the AS432 as an amplifier in control systems and power electronics.
Pin Configuration Ñ Top view
TO-92 (LP) |
SOIC (D) |
CATHODE |
1 |
8 |
REFERENCE |
CATHODE |
|
|
|
ANODE |
2 |
7 |
ANODE |
ANODE |
|
|
ANODE |
ANODE |
3 |
6 |
|
REFERENCE |
|
|
N/C |
N/C |
4 |
5 |
SOT-23/5L (DBV) |
SOT-89 (S) |
SOT-23/3L (VS) |
N/C |
ANODE |
|
|
N/C |
|
CATHODE |
REFERENCE |
Ordering Information
CATHODE |
ANODE |
REFERENCE |
AS432 A 2 D 7
Circuit Type:
1.24V Precision Adjustable
Shunt Regulator/Amplifier
Temperature Range:
A= 0°C to 70°C
B= 0°C to 105°C
C= –40°C to +85°C
Bandgap Tolerance: 2 = ±2% 1 = ±1%
R5 = ±0.5%
R25 = ±0.25%
CATHODE
ANODE
REFERENCE
Packaging Option:
A= Ammo Pack
B= Bulk
T = Tube
7 = Tape and Reel (7" Reel Dia)
13 = Tape and Reel (13" Reel Dia)
Package Style:
D = SOIC
DBV = SOT-23/5L
LP = TO-92
S = SOT-89
VS = SOT-23/3L
ASTEC Semiconductor |
1 |
AS432 |
1.24V Precision Adjustable Shunt Reference/Amplifier |
Functional Block Diagram
|
CATHODE (K) |
REFERENCE |
+ |
(R) |
Ð |
|
|
|
+ |
|
1.24 V |
|
Ð |
ANODE (A)
Absolute Maximum Ratings
Parameter |
Symbol |
Rating |
Units |
Cathode-Anode Reverse Breakdown |
VKA |
18 |
V |
Anode-Cathode Forward Current |
IAK |
1 |
A |
Operating Cathode Current |
IKA |
100 |
mA |
Reference Input Current |
IREF |
1 |
mA |
Continuous Power at 25¡C |
PD |
|
|
TO-92 |
|
775 |
mW |
8L SOIC |
|
750 |
mW |
SOT-89 |
|
1000 |
mW |
SOT-23/3L/5L |
|
200 |
mW |
|
|
|
|
Junction Temperature |
TJ |
150 |
¡C |
Storage Temperature |
TSTG |
Ð65 to 150 |
¡C |
Lead Temperature (Soldering 10 sec.) |
TL |
300 |
¡C |
Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
Recommended Conditions
Parameter |
Symbol |
Rating |
Unit |
Cathode Voltage |
VKA |
VREF to 18 |
V |
Cathode Current |
IK |
10 |
mA |
Typical Thermal Resistances
Package |
θJA |
θJC |
Typical Derating |
TO-92 |
160¡C/W |
80¡C/W |
6.3 mW/¡C |
|
|
|
|
SOIC |
175¡C/W |
45¡C/W |
5.7 mW/¡C |
|
|
|
|
SOT-89 |
110¡C/W |
8¡C/W |
9.1 mW/¡C |
|
|
|
|
SOT-23/3L/5L |
575¡C/W |
150¡C/W |
1.7 mW/¡C |
|
|
|
|
ASTEC Semiconductor |
2 |
1.24V Precision Adjustable Shunt Reference/Amplifier |
AS432 |
Electrical Characteristics
Electrical characteristics are guaranteed over the full junction temperature range (0Ð105¡C). Ambient temperature must be derated based upon power dissipation and package thermal characteristics. Unless otherwise stated, test conditions are: VKA = VREF and IK = 10 mA.
|
|
Test |
AS432 (0.25%) |
AS432 (0.5%) |
|
||||
Parameter |
Symbol |
Condition |
Min. |
Typ. |
Max. |
Min. |
Typ. |
Max. |
Unit |
|
|
|
|
|
|
|
|
|
|
Output Voltage |
VREF |
IK = 10 mA |
1.237 |
1.240 |
1.243 |
1.234 |
1.240 |
1.246 |
V |
|
|
TJ = 25¡C |
|
|
|
|
|
|
|
|
|
VK = VREF |
|
|
|
|
|
|
|
Line Regulation |
ÆVREF |
VKA = 1.25 to 15 V |
|
28 |
50 |
|
28 |
50 |
mV |
Load Regulation |
ÆVREF |
IK = 1 to 100 mA |
|
3.9 |
6 |
|
3.9 |
6 |
mV |
Temperature Deviation |
ÆVREF |
0 < TJ < 105¡C |
|
5 |
10 |
|
5 |
10 |
mV |
Reference Input Current |
IREF |
|
|
2.3 |
6 |
|
2.3 |
6 |
µA |
Reference Input Current |
ÆIREF |
0 < TJ < 105¡C |
|
0.14 |
0.6 |
|
0.14 |
0.6 |
µA |
Temperature Coefficient |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Minimum Cathode |
IK(min) |
|
|
0.2 |
1 |
|
0.2 |
1 |
mA |
Current for Regulation |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Off State Leakage |
IK(min) |
VREF = 0 V, |
|
0.04 |
500 |
|
0.04 |
500 |
nA |
|
|
VKA = 15 V |
|
|
|
|
|
|
|
|
|
Test |
AS432 (1.0%) |
AS432 (2.0%) |
|
||||
Parameter |
Symbol |
Condition |
Min. |
Typ. |
Max. |
Min. |
Typ. |
Max. |
Unit |
|
|
|
|
|
|
|
|
|
|
Output Voltage |
VREF |
IK = 10 mA |
1.228 |
1.240 |
1.252 |
1.215 |
1.240 |
1.256 |
V |
|
|
TJ = 25¡C |
|
|
|
|
|
|
|
|
|
VK = VREF |
|
|
|
|
|
|
|
Line Regulation |
ÆVREF |
VKA = 1.25 to 15 V |
|
28 |
50 |
|
28 |
50 |
mV |
Load Regulation |
ÆVREF |
IK = 1 to 100 mA |
|
3.9 |
6 |
|
3.9 |
6 |
mV |
Temperature Deviation |
ÆVREF |
0 < TJ < 105¡C |
|
5 |
12 |
|
5 |
12 |
mV |
Reference Input Current |
IREF |
|
|
2.3 |
6 |
|
2.3 |
6 |
µA |
Reference Input Current |
ÆIREF |
0 < TJ < 105¡C |
|
0.14 |
0.6 |
|
0.14 |
0.6 |
µA |
Temperature Coefficient |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Minimum Cathode |
IK(min) |
|
|
0.2 |
1 |
|
0.2 |
1 |
mA |
Current for Regulation |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Off State Leakage |
IK(min) |
VREF = 0 V, |
|
0.04 |
500 |
|
0.04 |
500 |
nA |
|
|
VKA = 15 V |
|
|
|
|
|
|
|
*Temperature deviation is defined as the maximum deviation of the reference over the given temperature range and does not imply an incremental deviation at any given temperature.
ASTEC Semiconductor |
3 |