ASRock P4I45PE R3.0 User Manual
P4i45PE
User Manual
Version 3.0
Published October 2003
Copyright©2003 ASRock INC. All rights reserved.
1
Copyright Notice:
No part of this manual may be reproduced, transcribed, transmitted, or translated in
any language, in any form or by any means, except duplication of documentation by
the purchaser for backup purpose, without written consent of ASRock Inc.
Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for
identification or explanation and to the owners’ benefit, without intent to infringe.
Disclaimer:
Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed
as a commitment by ASRock. ASRock assumes no responsibility for any errors or
omissions that may appear in this manual.
With respect to the contents of this manual, ASRock does not provide warranty of
any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose.
In no event shall ASRock, its directors, officers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of profits, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from
any defect or error in the manual or product.
ASRock Website: http://www.asrock.com
2
Contents
1 Introduction ................................................... 4
1.1 Package Contents .......................................................... 4
1.2 Specifications ................................................................ 5
1.3 Motherboard Layout ...................................................... 8
1.4 ASRock I/OTM.................................................................. 9
2 Installation...................................................... 10
2.1 Screw Holes ................................................................. 10
2.2 Pre-installation Precautions ........................................... 10
2.3 CPU Installation .............................................................. 11
2.4 Installation of CPU fan and Heatsink ............................. 11
2.5 Installation of Memory Modules (DIMM)......................... 12
2.6 Expansion Slots (PCI and AGP Slots) ........................... 13
2.7 Jumpers Setup .............................................................. 14
2.8 Connectors .................................................................... 15
3 BIOS Setup ...................................................... 17
3.1 BIOS Setup Utility ........................................................... 17
3.1.1 BIOS Menu Bar ....................................................... 17
3.1.2 Legend Bar ............................................................. 17
3.2 Main Menu...................................................................... 18
3.3 Advanced, Security, Power, Boot, and Exit Menus ..... 20
4 Software Support ........................................... 21
4.1 Installing Operating System ........................................... 21
4.2 Support CD Information ................................................. 21
4.2.1 Running Support CD ............................................... 21
4.2.2 Drivers Menu .......................................................... 21
4.2.3 Utilities Menu ........................................................... 21
4.2.4 ASRock “PC-DIY Live Demo” Program ................... 21
4.2.5 Contact Information ................................................ 21
Appendix ............................................................ 22
1. Advanced BIOS Setup Menu............................................ 22
2. Security Setup Menu ........................................................ 27
3. Power Setup Menu ........................................................... 28
4. Boot Setup Menu .............................................................. 29
5. Exit Menu .......................................................................... 30
3
Chapter 1 Introduction
Thank you for purchasing ASRock P4i45PE motherboard, a reliable motherboard
produced under ASRock’s consistently stringent quality control. It delivers excellent
performance with robust design conforming to ASRock’s commitment to quality and
endurance.
Chapter 1 and 2 of this manual contain introduction of the motherboard and step-bystep installation guide for new DIY system builders. Chapter 3 and 4 contain basic
BIOS setup and Support CD information.
For advanced users’ reference, the Appendix appearing on page 22 offers more
advanced BIOS setup information.
Because the motherboard specifications and the BIOS software
might be updated, the content of this manual will be subject to
change without notice. In case any modifications of this manual
occur, the updated version will be available on ASRock website
without further notice. You may find the latest memory and CPU
support lists on ASRock website as well.
ASRock website http://www.asrock.com
1.1 Package Contents
ASRock P4i45PE Motherboard (ATX Form Factor: 12.0-in x 7.0-in, 30.5 cm x 17.8 cm)
ASRock P4i45PE Quick Installation Guide
ASRock P4i45PE Support CD
One 80-conductor Ultra ATA 66/100 IDE Ribbon Cable
One Ribbon Cable for a 3.5-in Floppy Drive
One ASRock I/OTM Shield
4
1.2 Specifications
Platform: ATX Form Factor (12.0-in x 7.0-in, 30.5 cm x 17.8 cm)
CPU: Socket 478 for Intel® Pentium® 4/ Celeron® processor
Chipsets: North Bridge:
Intel® 845PE chipsets, standard FSB @ 533 / 400MHz,
Max. 800+ MHz at overclocking mode (see CAUTION 1),
supports Hyper-Threading Technology (see CAUTION 2);
South Bridge:
Intel® ICH4
Memory: 2 DDR DIMM slots: DDR 1 and DDR2
PC2100 (DDR266) / PC2700 (DDR333), Max. 2GB
PC3200 (DDR400) at overclocking mode, Max. 1GB
IDE: IDE1: ATA 100 / Ultra DMA Mode 5;
IDE2: ATA 100 / Ultra DMA Mode 5;
Supports up to 4 IDE devices
Floppy Port: Supports up to 2 floppy disk drives
Audio: 5.1 channels AC’97 Audio
PCI LAN: Speed: 802.3u (10/100 Ethernet), supports Wake-On-LAN
Hardware Monitor: CPU temperature sensing (ASRock U-COP);
Chassis temperature sensing;
CPU overheat shutdown to protect CPU life
(ASRock U-COP)(see CAUTION 3);
CPU fan tachometer; Chassis fan tachometer;
Voltage monitoring: +12V, +5V, +3V, Vcore
PCI slots: 5 PCI slots with PCI Specification 2.2
AGP slot: 1 AGP slot, supports 1.5V, 4X AGP card (see CAUTION 4)
USB 2.0: 4 default USB 2.0 ports and one extra set of header for two
additional USB 2.0 ports upgrade (see CAUTION 5)
ASRock I/OTM: PS/2: 1 keyboard port / 1 mouse port;
1 RJ 45 port;
4 rear default USB 2.0 ports;
1 serial port: COM1; 1 parallel port: ECP/EPP support;
Audio Jack: Line Out / Line In / Microphone + 1 Game port
BIOS: AMI legal BIOS;Supports “Plug and Play”;
ACPI 1.1 compliance wake up events;
Supports jumperfree; SMBIOS 2.3.1 support;
CPU frequency stepless control
(only for advanced users’ reference, see CAUTION 6);
OS: Microsoft® Windows® 98 SE / ME / 2000 / XP compliant
5
CAUTION!
1. P4i45PE motherboard may be fine tuned to support higher CPU bus
frequencies on certain condition (over-clocking mode). Please refer
to the NOTE on page 7 for the details.
2. About the setting of “Hyper Threading Technology”, please check
page 22.
3. While CPU overheat is detected, the system will automatically shutdown.
Please check if the CPU fan on the motherboard functions properly
before you resume the system. To improve heat dissipation, remember to
spray thermal grease between the CPU and the heatsink when you install
the PC system.
4. Do NOT plug a 3.3V AGP card in the AGP slot on P4i45PE motherboard!
It may cause permanent damage!
5. Power Management for USB 2.0 works fine under Microsoft
XP SP1 / 2000 SP4. It may not work properly under Microsoft® Windows
98 / ME. Please refer to Microsoft® official document at
http://www.microsoft.com/whdc/hwdev/bus/USB/USB2support.mspx
6. Although P4i45PE offers stepless control, it is not recommended to
perform over clocking. When the CPU frequency of P4i45PE is set to
perform over clocking, other clocks, such as PCI clock, AGP clock, and
Memory clock will also be overclocked proportionally. Frequencies other
than the recommended CPU bus frequencies may cause the instability of
the system or damage the CPU and the motherboard.
®
Windows
®
®
6
NOTE
P4i45PE may be fine tuned to support higher CPU front side bus frequencies on certain
condition at over-clocking mode. Please refer to the tables below for the details.
CPU FSB Configuration Note
P4i45PE 800 MHz 1. Set the “FSB” jumper to “800” mode (see page 14).
2. Only support one DDR 400 memory module on DDR1
DIMM. (If it is set to DDR 400 mode, then it does not
support CL3 module.)
3. Update BIOS version to 2.10 or later version.
The Recommended Memory Modules lists for
P4i45PE motherboard.
FSB 800 MHz / DDR 400 Mode
DRAM SIZE TYPE CELL CELL NO. SINGLE SIDE /
VENDOR (MB) VENDOR DOUBLE SIDE
ADATA 512 DDR400 ADATA ADD8608A8A-58 DOUBL E SIDE
ADATA 256 DDR450 ADATA ADD8608A8A-4.58 SINGLE SIDE
ADATA 256 DDR400 WINBOND W942508CH-5 SINGLE SIDE
APACER 512 DDR400 PSC A2S56D30ATP DOUB LE SID E
APACER 512 DDR400 SAMSUNG K4H560838D-TCCC DOUBLE SIDE
APACER 256 DDR400 INFINEON HYB25D256800BT-5 SINGLE SIDE
APACER 256 DDR400 SAMSUNG K4H560838D-TCCC SINGLE SIDE
INFINEON 256 DDR400 INFINEON HYB25D256800BT-5 SINGLE SIDE
INFINEON 128 DDR400 INFINEON HYB250256160BT-5 SINGLE SIDE
KINGMAX 512 DDR400 KINGMAX KDL3888P4EA-50 DOUBLE SIDE
KINGMAX 256 DDR400 KINGMAX KDL684T4AA-50 SINGLE SIDE
KINGSTON 256 DDR400 MOSEL V58C2256804SAT 5 SINGLE SIDE
KINGSTON 256 DDR400 HYNIX HY5DU56822BT-D43 SINGLE SIDE
KINGSTON 256 DDR400 WINBOND W942508CH-5 SINGLE SIDE
MICRON 128 DDR400 MICRON 46V16M8 SINGLE SIDE
SAMSUNG 512 DDR400 SAMSUNG K4H560838D-TCCC DOUBLE SIDE
SAMSUNG 256 DDR400 SAMSUNG K4H560838E-TCC C SINGLE SIDE
TWINMOS 512 DDR400 M.tec TTD7608F8E50B DOUB LE SIDE
TWINMOS 256 DDR466 TWINMOS TMD7608F8E43B SINGLE SIDE
TWINMOS 256 DDR400 TWINMOS TMD7608F8E50B SINGLE SIDE
TWINMOS 256 DDR400 M.tec TTD7608F8E50B SINGLE SIDE
Since the memory types are changing rapidly,
please visit ASRock website (http://www.asrock.com/support/index.htm)
for the latest recommended memory support list.
7
1.3 Motherboard Layout
2
FSB
3
5.1CH
USB2.0
4
PGA478
Chipset
P4i45PE
1
PS/2
Mouse
PS2_USB_PWR1
PS/2
1
Keyboard
1
CPU_FAN1
COM1
PARALLEL PORT
27
LAN
USB 2.0
Ports
USB 2.0
Ports
26
Lineout
Line
Line in
In
Mic
GAME AUDIO1
Mic in
GAME AUDIO1
In
CD1
25
24
23
22
21
AUX1
1
JR1 JL1
AUDIO
CODEC
PCI
LAN
AUDIO1
20
Super
I/O
2MB
19
BIOS
17.8cm (7.0 in)
Intel
845PE
1.5V_AGP1
PCI 1
PCI 2
PCI 3
CLRCMOS0
PCI 4
DDR400
FSB800
PCI 5
5
FLOPPY1
1
67
DDR2 (64/72bit, 184-pin module)
DDR1 (64/72bit, 184-pin module)
Intel
ICH4
CMOS
Battery
1
IR1
USB45
1
SPEAKER1
IDE2
PLED PWRBTN
1
HDLED RESET
ATXPWR1
IDE1
CHA_FAN1
PANEL1
8
9
30.5cm (12.0 in)
10
11
12
13
14
15
16
17
18
1 FSB Select Jumper (FSB) 15 Chassis Speaker Connector (SPEAKER 1)
2 PS2_USB_PWR1 Jumper 16 System Panel Connector (PANEL1)
3 CPU Heatsink Retention Module 17 Infrared Module Connector (IR1)
4 CPU Socket 18 USB 2.0 Header (USB45, Blue)
5 North Bridge Controller 19 BIOS FWH Chip
6 184-pin DDR DIMM Slots (DDR1- 2) 20 PCI Slots (PCI1- 5)
7 ATX Power Connector (ATXPWR1) 21 PCI LAN
8 Secondary IDE Connector (IDE2, Black) 22 JL1 Jumper
9 Primary IDE Connector (IDE1, Blue) 23 JR1 Jumper
10 AGP Slot (1.5V_AGP1) 24 Front Panel Audio Connector (AUDIO1)
11 South Bridge Controller 25 Internal Audio Connector: AUX1 (White)
12 Chassis Fan Connector (CHA_FAN1) 26 Internal Audio Connector: CD1 (Black)
13 Clear CMOS Jumper (CLRCMOS0) 27 CPU Fan Connector (CPU_FAN1)
14 Floppy Connector (FLOPPY1)
8
1.4 ASRock I/O
TM
12
910
1 Parallel Port 6 Line Out (Lime)
2 RJ-45 Port 7 USB 2.0 Ports
3 Game Port 8 Serial Port (COM1)
4 Microphone (Pink) 9 PS/2 Keyboard Port (Purple)
5 Line In (Light Blue) 10 PS/2 Mouse Port (Green)
8
3
4567
9
Loading...