ASROCK P4i45GV User Manual

Download

P4i45GL

P4i45GV

User Manual

Version 3.0

Published July 2003

No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:

Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. With respect to the contents of this manual, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the manual or product.

ASRock Website: http://www.asrock.com

Contents

1 Introduction.................................................... 4

1.1 Package Contents ........................................................... 4

1.2 Specifications ................................................................. 5

1.3 Motherboard Layout (P4i45GL) ...................................... 8

1.4 Motherboard Layout (P4i45GV)...................................... 9

1.5 ASRock I/OTM (P4i45GL / P4i45GV) ................................ 10

2 Installation ...................................................... 11

2.1 Screw Holes ................................................................... 11

2.2 Pre-installation Precautions ............................................ 11

2.3 CPU Installation ............................................................... 12

2.4 Installation of Heatsink and CPU fan .............................. 12

2.5 Installation of Memory Modules (DIMM) .......................... 13

2.6 Expansion Slots .............................................................. 13

2.7 Jumpers Setup ................................................................ 14

2.8 Connectors ..................................................................... 15

3 BIOS Setup ...................................................... 17

3.1 BIOS Setup Utility ............................................................ 17

3.1.1 BIOS Menu Bar ..................................................... 17

3.1.2 Legend Bar ........................................................... 17

3.2 Main Menu ....................................................................... 18

3.3 Advanced, Security, Power, Boot, and Exit Menus ...... 20

4 Software Support ........................................... 21

4.1 Installing Operating System ............................................ 21

4.2 Support CD Information ................................................... 21

4.2.1 Running Support CD ............................................. 21

4.2.2 Drivers Menu ........................................................ 21

4.2.3 Utilities Menu ......................................................... 21

4.2.4 ASRock “PC-DIY Live Demo” Program ................. 21

4.2.5 Contact Information ............................................... 21

Appendix ........................................................... 22

1. Advanced Menu ............................................................. 22

2. Security Menu ................................................................. 26

3. Power Menu ................................................................... 27

4. Boot Menu ....................................................................... 28

5. Exit Menu ......................................................................... 29

Chapter 1 Introduction

Thank you for purchasing ASRock P4i45GL / P4i45GV motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance. Chapter 1 and 2 of this manual contain introduction of the motherboard and step-bystep installation guide for new DIY system builders. Chapter 3 and 4 contain basic BIOS setup and Support CD information. For advanced users’ reference, the Appendix appearing on page 22 offers more advanced BIOS setup information.

Because the motherboard specifications and the BIOS software might be updated, the content of this manual will be subject to change without notice. In case any modifications of this manual occur, the updated version will be available on ASRock website without further notice. You may find the latest memory and CPU support lists on ASRock website as well. ASRock website http://www.asrock.com

1.1 Package Contents

ASRock P4i45GL or P4i45GV motherboard (Micro ATX form factor: 9.6" x 7.0", 24.4 x 17.8 cm) ASRock P4i45GL / P4i45GV Quick Installation Guide ASRock Intel-Intel Support CD 1 cable for IDE devices (1 x ATA 66 / 100) 1 cable for floppy drive (1 x ribbon cable) 1 ASRock I/O shield 1 COM port bracket

1.2 Specifications

Platform: Micro ATX form factor (9.6" x 7.0", 24.4 x 17.8 cm) CPU: Socket 478 for Intel® Pentium® 4 / Celeron® processor Chipsets: North Bridge (P4i45GL):

Intel® 845GL chipsets, standard FSB 400MHz (see CAUTION 1), Max. 533 MHz (at overclocking mode, see CAUTION 2);

North Bridge (P4i45GV):

Intel® 845GV chipsets, standard FSB 533 MHz, supports Hyper-Threading Technology (see CAUTION 3);

South Bridge: Intel® ICH4

VGA: Intel® Extreme Graphics, Max. 64MB VRAM Memory: P4i45GL:

2 DDR DIMM slots, DDR DIMM1 and DDR DIMM2 supports PC1600 (DDR200) / PC2100 (DDR266), Max. 2GB;

P4i45GV:

2 DDR DIMM slots, DDR DIMM1 and DDR DIMM2 supports PC2100 (DDR266) / PC2700 (DDR333), Max. 2GB (see CAUTION 4)

IDE: IDE1: ATA 100 / Ultra DMA Mode 5;

IDE2: ATA 100 / Ultra DMA Mode 5; Can connect up to 4 IDE devices

Floppy Port: Supports 2 floppy disk drives Audio: 5.1 channels AC’97 Audio PCI LAN (Optional): Speed: 802.3u (10/100 Ethernet), supports Wake-On-LAN Hardware Monitor:

CPU temperature sensing (ASRock U-COP); Chassis temperature sensing; CPU overheat shutdown to protect CPU life (ASRock U-COP) (see CAUTION 5); Voltage monitoring: +12V, +5V, +3V, Vcore; CPU fan tachometer; Chassis fan tachometer

PCI slots: 2 slots with PCI Specification 2.2 AMR slot: 1 slot, supports ASRock MR card (Optional) USB 2.0: 4 default USB 2.0 ports and 1 extra set of header for 2 additional

USB 2.0 ports upgrade (see CAUTION 6)

ASRock I/OTM: PS/2: 1 keyboard port / 1 mouse port;

1 RJ 45 port; 4 rear default USB 2.0 ports; 1 VGA port; 1 parallel port: ECP/EPP support; Audio Jack: Line Out/ Line In/ Microphone + Game port

BIOS: AMI legal BIOS; Supports “Plug and Play”;

ACPI 1.1 compliance wake up events; Supports jumperfree; SMBIOS 2.3.1 support; CPU frequency stepless control (only for advanced users’ reference, see CAUTION 7)

OS: Microsoft® Windows® 98SE / ME / 2000 / XP compliant

CAUTION!

1. P4i45GL motherboard may be fine tuned to support higher CPU bus frequencies on certain condition. Please refer to “NOTE” on page 7 for the details.

2. If the installed CPU runs with the FSB frequency at 533MHz on P4i45GL motherboard, it will support PC2100(DDR266) and PC2800(DDR350).

3. About the setting of “Hyper Threading Technology”, please check page 22.

4. P4i45GV motherboard will support PC2700(DDR333) when the installed CPU runs with the FSB frequency at 533MHz.

5. While CPU overheat is detected, the system will automatically shutdown. Please check if the CPU fan on the motherboard functions properly before you resume the system. To improve heat dissipation, remember to spray thermal grease between the CPU and the heatsink when you install the PC system.

6. Power Management for USB 2.0 works fine under Microsoft Windows® XP. It may not work properly under Microsoft Windows® 98/ME/2000. Please refer to Microsoft® official document at

http://www.microsoft.com/whdc/hwdev/bus/USB/USB2support.mspx

7. Although P4i45GL / P4i45GV offers stepless control,it is not recommended to perform over clocking. When the CPU frequency of P4i45GL / P4i45GV is set to perform over clocking, other clocks, such as PCI clock and Memory clock will also be overclocked proportionally. Frequencies other than the recommended CPU bus frequencies may cause the instability of the system or damage the CPU and the motherboard.

NOTE

P4i45GL may be fine tuned to support higher CPU front side bus frequencies on certain condition. Please refer to the table below for the details.

CPU FSB Configuration Note

P4i45GL 533 MHz 1. It supports DDR266 memory module

at both DDR DIMM1 and DIMM2.

2. It supports DDR350 memory module ONLY at DDR DIMM1.

3. To support DDR350, please set DDR350 in BIOS DRAM Frequency.

4. It supports CL=2 and CL=2.5 only.

The Recommended Memory Modules list for

P4i45GL motherboard.

FSB 533MHz / DDR350 Mode

DRAM SIZE TYPE CELL CELL NO. SINGLE SIDE /

VENDOR (MB) VENDOR DOUBLE SIDE

TWINMOS 256 DDR333 TWINMOS TMD7608F8E60B SINGLE SIDE

TWINMOS 256 DDR400 TWINMOS TMD7608F8E50B SINGLE SIDE

TWINMOS 512 DDR400 TWINMOS TMB7608F8E50B DOUBL E SIDE

TWINMOS 512 DDR400 M.TEC T TD7608F8E50B DOUBL E SIDE

ADATA 256 DDR400 WINBOND 424764800 SINGLE SIDE

ADATA 256 DDR400 WINBOND W942508BH-5 SINGLE SIDE

ADATA 256 DDR400 ADATA ADD8608A8A-4.5B SINGLE SIDE

KINGMAX 256 DDR400 KINGMAX KDL388P4EA-50 SINGLE SIDE

KINGMAX 512 DDR400 KINGMAX KDL388P4EA-50 DO UBLE SI DE

KINGSTON 256 DDR333 MOSEL V58C2256804SAT6 SINGLE SIDE

KINGSTON 512 DDR333 INFINEON HYB25D256800BT-6 DOUBLE SIDE

MICRON 256 DDR333 MICRON 46V32M8-6TC SINGLE SIDE

MICRON 256 DDR400 MICRON 46V16M8 DOU BLE SID E

INFINEON 128 DDR400 INFINEON HYB25D256800BT-5 SINGLE SIDE

INFINEON 256 DDR400 INFINEON HYB25D256800BT-5 SINGLE SIDE

TRANSCEND 256 DDR333 SAMSUNG K4H560838D-TCB3 SINGLE SIDE

APACER 256 DDR333 SAMSUNG K4H560838D-TCB3 SINGLE SIDE

Since the memory types are changing rapidly, please visit ASRock website (http://www.asrock.com/support/index.htm) for the latest recommended memory support list.

1.3 Motherboard Layout (P4i45GL)

26 25 24 23 22 21 20

PS/2

Mouse

PS/2

Keyboard

VGA

LAN

(optional)

USB 2.0

Ports

USB 2.0

Ports

Lineout

Line in

GAME AUDIO1

Line In

Mic

Mic in

17.8cm (7.0 in)

PS2_USB_PWR1

CPU_FAN1

PARALLEL PORT

mPGA478B

ATXPWR1

24.4cm (9.6 in)

7 8

Intel

845GL

Chipset

PCI

LAN

PCI 1

PCI 2

COM1

AUDIO1

JR1 JL1

AUDIO CODEC

Super

I/O

FLOPPY1

2MB

BIOS

AMR1

CMOS

Battery

CLRCMOS0

5.1CH

1516

DDR1 (64/72bit, 184-pin module)

USB2.0

Intel ICH4

USB45

DDR2 (64/72bit, 184-pin module)

SPEAKER1

IR1

IDE1 IDE2

CHA_FAN1

PLED PWRBTN

HDLED RST

PANEL1

P4i45GL

10 11

1 CPU Fan Connector (CPU_FAN1) 2 PS2_USB_PWR1 Jumper 3 CPU Heatsink Retention Module 4 CPU Socket 5 184-pin DDR DIMM Slots (DDR DIMM1- 2) 6 ATX Power Connector (ATXPWR1) 7 Primary IDE Connector (IDE1, Blue) 8 Secondary IDE Connector (IDE2, Black) 9 South Bridge Controller 10 Chassis Fan Connector (CHA_FAN1) 11 External Speaker Connector (SPEAKER1) 12 System Panel Connector (PANEL1) 13 Infrared Module Connector (IR1) 14 USB 2.0 Header (USB45, Blue) 15 Clear CMOS (CLRCMOS0, 2-pin jumper) 16 Floppy Connector (FLOPPY1) 17 Serial Port Connector (COM1) 18 AMR Slot (AMR1) 19 BIOS FWH Chip 20 AUDIO CODEC 21 PCI Slots (PCI 1- 2) 22 JL1 Jumper 23 JR1 Jumper 24 Front Panel Audio Connector (AUDIO1) 25 PCI LAN (Optional) 26 Internal Audio Connector: AUX1 (White) 27 Internal Audio Connector: CD1 (Black) 28 North Bridge Controller

1.4 Motherboard Layout (P4i45GV)

26 25 24 23 22 21 20

PS/2

Mouse

PS/2

Keyboard

VGA

LAN

(optional)

USB 2.0

Ports

USB 2.0

Ports

Lineout

Line in

GAME AUDIO1

Mic in

17.8cm (7.0 in)

PS2_USB_PWR1

CPU_FAN1

PARALLEL PORT

mPGA478B

ATXPWR1

24.4cm (9.6 in)

7 8

Line In

Mic In

AUDIO1

JR1 JL1

AUDIO

CODEC

Super

I/O

FLOPPY1

2MB BIOS

AMR1

Intel

845GV

Chipset

PCI

LAN

PCI 1

PCI 2

COM1

CMOS

Battery

CLRCMOS0

USB2.0

5.1CH

1516

DDR1 (64/72bit, 184-pin module)

USB45

Intel

ICH4

DDR2 (64/72bit, 184-pin module)

SPEAKER1

IR1

IDE1 IDE2

CHA_FAN1

PLED PWRBTN

HDLED RST

PANEL1

P4i45GV

10 11

1.5 ASRock I/OTM (P4i45GL / P4i45GV)

1 Parallel Port 2 RJ-45 Port (Optional) 3 Game Port 4 Microphone (Pink) 5 Line In (Light Blue) 6 Line Out (Lime) 7 USB 2.0 Ports 8 VGA Port 9 PS/2 Keyboard Port (Purple) 10 PS/2 Mouse Port (Green)

Chapter 2 Installation

P4i45GL / P4i45GV is a Micro ATX form factor (9.6" x 7.0", 24.4 x 17.8 cm) motherboard. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it.

Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so may cause physical injuries to you and damages to motherboard components.

2.1 Screw Holes

Place screws into the holes indicated by circles to secure the motherboard to the chassis.

Do not over-tighten the screws! Doing so may damage the motherboard.

2.2 Pre-installation Precautions

Take note of the following precautions before you install motherboard components or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any component.

2. To avoid damaging the motherboard components due to static electricity, NEVER place your motherboard directly on the carpet or the like. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that comes with the component.

Before you install or remove any component, ensure that the power is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components.

2.3 CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90o angle. Step 2. Position the CPU directly above the socket such that its marked corner

matches the base of the socket lever.

Step 3. Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the CPU into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push

down the socket lever to secure the CPU. The lever clicks on the side tab to indicate that it is locked.

Step 1 Step 2, 3 Step 4

2.4 Installation of CPU Fan and Heatsink

Intel® Pentium®4 CPU requires larger heatsink and cooling fan. Thermal grease between the CPU and the heatsink is also needed to improve heat dissipation. Make sure that the CPU and the heatsink are securely fastened and in good contact with each other. For proper installation, please kindly refer to the instruction manuals of the CPU fan and heatsink vendors.

2.5 Installation of Memory Modules (DIMM)

P4i45GL / P4i45GV motherboard provides two 184-pin DDR (Double Data Rate) DIMM slots.

Please make sure to disconnect power supply before adding or removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward. Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

Step 3. Firmly insert the DIMM into the slot until the retaining clip snap back in place

and the DIMM is properly seated.

2.6 Expansion Slots (PCI and AMR Slots)

There are 2 PCI slots and 1 AMR slot on P4i45GL / P4i45GV motherboard. PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

AMR slot: AMR slot is used to insert an ASRock MR card (optional) with v.92

Modem functionality.

Installing an expansion card

Step 1. Before installing the expansion card, read the documentation of the

expansion card and make necessary hardware settings for the card.

Step 2. Remove the system unit cover (if your motherboard is already installed in a

chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep the screws

for later use.

Step 4. Align the card connector with the slot and press firmly until the card is

completely seated on the slot. Step 5. Fasten the card to the chassis with screws. Step 6. Replace the system cover.

2.7 Jumpers Setup

The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “SHORT”. If no jumper cap is placed on pins, the jumper is “OPEN”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “SHORT” when jumper cap is placed on these 2 pins.

Jumper Setting Description

PS2_USB_PWR1 Short pin2, pin3 to enable

(see p.8/p.9 item 2) +5VSB (standby) for PS/2 or

1_2

+5V

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by

power supply.

2_3

+5VSB

USB wake up events.

JR1(see p.8/p.9 item 23) JL1(see p.8/p.9 item 22)

JR1 JL1 JR1 JL1

fig. 1 fig. 2

Note: When you connect speakers in back panel and front panel at the same time,

1. If the jumpers JL1 and JR1 are short (see fig. 1), both front panel and rear panel audio connectors can work.

2. If both jumper caps on JL1 and JR1 are removed (see fig. 2), only front panel audio works.

However, it requires your front panel to support the function.

Clear CMOS

CLRCMOS0

(see p.8/p.9 item 15)

2-pin jumper

Note: CLRCMOS0 allows you to clear the data in CMOS. The data in CMOS includes

system setup information such as system password, date, time, and system setup parameters. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord, then use a jumper cap to short the pins on CLRCMOS0 for 3 seconds. Please remember to remove the jumper cap after clearing the CMOS.

2.8 Connectors

Connectors are NOT jumpers. DO NOT place jumper caps over these connectors.

Connector Figure Description

FDD connector (33-pin FLOPPY1)

(see p.8/p.9 item 16)

Note: Match the red marking on the floppy ribbon cable with Pin1.

Primary IDE connector (Blue) Secondary IDE connector (Black)

(39-pin IDE1, see p.8/p.9 item 7) (39-pin IDE2, see p.8/p.9 item 8)

Pin1

FLOPPY1

Red marking

PIN1

Connect this end

IDE1

to the motherboard

BLUE

PIN1

IDE2

Connect this end to the IDE devices

BLACK

80-Pin ATA 100 cable

Note:To optimize compatibility and performance, please connect your hard disk

drive to the primary IDE connector (IDE1, blue) and CD-ROM to the secondary IDE connector (IDE2, black).

USB_PWR

AUX-L

GND GND

AUX-R

CD-L

GND GND

CD-R

P-5

P-4

IRTX

IRRX

P+5

P+4

+5V

GND

DUMMY

GND

DUMMY

AUX1

CD1

panel are not sufficient, this USB header is available for 2 additional USB 2.0 ports.

tuner card, or MPEG card.

USB 2.0 header ASRock I/OTM provides 4 (9-pin USB45) default USB 2.0 ports. If those

(see p.8/p.9 item 14) USB 2.0 ports on the rear

Infrared module connector This connector supports an (5-pin IR1) optional wireless transmitting

(see p.8/p.9 item 13) and receiving infrared module.

Internal audio connectors These connectors allow you (4-pin CD1, 4-pin AUX1) to receive stereo audio input

(CD1: see p.8/p.9 item 27) from sound sources such as (AUX1: see p.8/p.9 item 26) a CD-ROM, DVD/ROM, TV

GND

+5VA

MIC-POWER

MIC

PLED+

PLED-

HDLED-

HDLED+

BACKOUT-R

GND

AUD-OUT-R

PWRBTN#

GND

DUMMY

RESET#

GND

BACKOUT-L

AUD-OUT-L

control of audio devices.

Front panel audio connector This is an interface for front (9-pin AUDIO1) panel audio cable that allows

(see p.8/p.9 item 24) convenient connection and

System panel connector This connector accommo(9-pin PANEL1) dates several system front

(see p.8/p.9 item 12) panel functions.

External speaker connector This connector allows you (4-pin SPEAKER 1) to attach to an external

(see p.8/p.9 item 11) speaker.

Chassis fan connector Connect the fan cable to the (3-pin CHA_FAN1) connector matching the black

+5V

SPEAKER

DUMMY

GND +12V CHA_FAN_SPEED

(see p.8/p.9 item 10) wire to the ground pin.

CPU fan connector Connect the fan cable to the (3-pin CPU_FAN1) connector matching the black

CPU_FAN_SPEED

+12V

GND

(see p.8/p.9 item 1) wire to the ground pin.

ATX power connector Connect an ATX power (20-pin ATXPWR1) supply to the connector.

(see p.8/p.9 item 6)

RRXD1

DDTR#1

TTXD1

DDCD#1

DDSR#1

CCTS#1

RRTS#1

GND

RRI#1

Serial port connector This COM1 header supports (9-pin COM1) a serial port module.

(see p.8/p.9 item 17)

Chapter 3 BIOS Setup

3.1 BIOS Setup Utility

This section explains how to configure your system using the BIOS Setup Utility. The BIOS FWH chip on the motherboard stores the BIOS Setup Utility. When you start up the computer, there is a chance for you to run the BIOS Setup. Press <F2> during the Power-On-Self-Test (POST) to enter the BIOS Setup Utility, otherwise, POST continues with its test routines. If you wish to enter the BIOS Setup after POST, restart the system by pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system chassis. You can also restart by turning the system off and then back on. The BIOS Setup Utility is designed to be user-friendly. It is a menu-driven program, which allows you to scroll through its various sub-menus and select among the predetermined choices.

Because the BIOS software is constantly being updated, the following BIOS setup screens and descriptions are for reference purpose only, and may not exactly match what you see on your screen.

3.1.1 BIOS Menu Bar

The top of the screen has a menu bar with the following selections:

MAIN Sets up the basic system configuration ADVANCED Sets up the advanced features SECURITY Sets up the security features POWER Configures Power Management features BOOT Configures the default system device that is used

to locate and load the Operating System

EXIT Exits the current menu or the BIOS Setup

To access the menu bar items, press the right or left arrow key on the keyboard until the desired item is highlighted.

3.1.2 Legend Bar

At the bottom of the Setup Screen is a legend bar. The following table lists the keys in the legend bar with their corresponding functions.

Navigation Key(s) Function Description <F1> Displays the General Help Screen <ESC> Jumps to the Exit menu or returns to the upper menu

from the current menu

/ Moves cursor up or down between fields / Selects menu to the left or right + / - Increases or decreases values <Enter> Brings up a selected menu for a highlighted field <F9> Loads all the setup items to default value <F10> Saves changes and exits Setup

3.2 Main Menu

When you enter the BIOS Setup Utility, the following screen appears.

Advanced

Main

System Date System Time

Floppy Drives IDE Devices

BIOS Version Processor Type Processor Speed Cache Size Microcode Update TotalMemory

DDR1 DDR2

F1:Help

Esc:Exit

AMIBIOS SETUPUTILITY -VERSION 3.31a

Security

Jun

20:07:40

P4I45GL BIOS P2.00 Pentium (R) 4 CPU

2400 MHz 512 KB

F24/18 127MB+1MBShareMemory

128 MB / 133 MHz (DDR 266)

None

:Select Item :Select Menu

Power

27 2003 Fri

+/-:Change Values

Enter:Select

Boot

Exit

Sub-Menu

[ Setup Help ]

Month: Jan - Dec

Day: 01 -31

Year:1980-2099

F9:Setup Defaults F10:Save &Exit

System Date [Month/Day/Year]

Set the system date that you specify. Valid values for month, day, and year are Month: (Jan to Dec), Day: (1 to 31), Year: (up to 2099). Use keys to move between the Month, Day and Year fields.

System Time [Hour:Minute:Second]

Set the system to the time that you specify. Use keys to move between the Hour, Minute and Second fields.

Floppy Drives

Use this to set the type of floppy drives installed.

IDE Devices

Use this to configure IDE devices.

TYPE

To set the type of the IDE device, first, please select “IDE Devices” on Main menu and press <Enter> to get into the sub-menu. Then, select among “Primary IDE Master”, “Primary IDE Slave”, “Secondary IDE Master”, and “Secondary IDE Slave” to make configuration of its type. Below are the configuration options.

Main

Primary IDE Master:

Type Cylinders Heads Write Precompensation Sectors Maximum Capacity LBA Mode Block Mode Fast Programmed I/O Modes 32 Bit Transfer Mode Ultra DMA Mode

F1:Help

Esc:Previous Menu

AMIBIOS SETUPUTILITY -VERSION 3.31a

Auto

On On Auto On Auto

:Select Item

+/-:Change Values

Enter:Select

Sub-Menu

[ Setup Help ]

Select how to set the parameters of drive,

Or Select [AUTO] to set all HDD parameters automatically.

F9:Setup Defaults F10:Save &Exit

[USER]: It allows user to manually enter the number of cylinders, heads,

and sectors per track for the drive.

Before attempting to configure a hard disk drive, make sure you have the correct configuration information supplied by the drive manufacturer. Incorrect settings may cause the system to fail to recognize the installed hard disk.

[Auto]: Select [Auto] to automatically detect hard disk drive. If auto-

detection is successful, the BIOS Setup automatically fills in the correct values for the remaining fields on this sub-menu. If the autodetection fails, it may due to that the hard disk is too old or too new. If the hard disk was already formatted on an older system, the BIOS Setup may detect incorrect parameters. In these cases, select [User] to manually enter the IDE hard disk drive parameters.

After entering the hard disk information into BIOS, use a disk utility, such as FDISK, to partition and format new IDE hard disk drives. This is necessary so that you can write or read data from the hard disk. Make sure to set the partition of the Primary IDE hard disk drives to active.

[CD/DVD]: This is used for IDE CD/DVD drives. [ARMD]: This is used for IDE ARMD (ATAPI Removable Media Device),

such as MO.

Cylinders

This is used to configure the number of cylinders. Refer to the drive documentation to determine the correct value.

Heads

This is used to configure the number of read/write heads. Refer to the drive documentation to determine the correct values.

Write Pre-compensation

Enter Write Pre-compensation sector. Refer to the drive documentation to determine the correct value.

Sectors

This is used to configure the number of sectors per track. Refer to the drive documentation to determine the correct value.

Maximum Capacity

This field shows the drive’s maximum capacity as calculated by the BIOS based on the drive information you entered.

LBA Mode

This allows user to select the LBA mode for a hard disk > 512 MB under DOS and Windows; for Netware and UNIX user, select [Off] to disable the LBA mode.

Block Mode

Set the block mode to [On] will enhance hard disk performance by reading or writing more data during each transfer.

Fast Programmed I/O Modes

This allows user to set the PIO mode to enhance hard disk performance by optimizing the hard disk timing.

32 Bit Transfer Mode

It allows user to enable 32-bit access to maximize the IDE hard disk data transfer rate.

Ultra DMA Mode

Ultra DMA capability allows improved transfer speeds and data integrity for compatible IDE devices. Set to [Disabled] to suppress Ultra DMA capability.

3.3 Advanced, Security, Power, Boot, and Exit Menus

Detailed descriptions of these menus are listed in the Appendix. See page 22.

Chapter 4 Software Support

4.1 Install Operating System

This motherboard supports various Microsoft® Windows® operating systems: 98 SE / ME / 2000 / XP. Because motherboard settings and hardware options vary, use the setup procedures in this chapter for general reference only. Refer to your OS documentation for more information.

4.2 Support CD Information

The Support CD that came with the motherboard contains necessary drivers and useful utilities that enhance the motherboard features.

4.2.1 Running The Support CD

To begin using the support CD, insert the CD into your CD-ROM drive. The CD automatically displays the Main Menu if “AUTORUN” is enabled in your computer. If the Main Menu did not appear automatically, locate and double click on the file ASSETUP.EXE from the BIN folder in the Support CD to display the menus.

4.2.2 Drivers Menu

The Drivers Menu shows the available devices drivers if the system detects installed devices. Please install the necessary drivers to activate the devices.

4.2.3 Utilities Menu

The Utilities Menu shows the applications software that the motherboard supports. Click on a specific item then follow the installation wizard to install it.

4.2.4 ASRock PC-DIY Live Demo Program

ASRock presents you a multimedia PC-DIY live demo, which shows you how to install your own PC system step by step. You can find the file through the following path:

..\ MPEGAV \ AVSEQ01.DAT

To see this demo program, you can run Microsoft® Media Player® to play the file.

4.2.5 Contact Information

If you need to contact ASRock or want to know more about ASRock, welcome to visit ASRock’s website at http://www.asrock.com; or you may contact your dealer for further information.

Appendix: Advanced BIOS Setup

This section will introduce you the following BIOS Setup menus: “Advanced,” “Security,” “Power,” “Boot,” and “Exit.”

1. Advanced BIOS Setup Menu

Advanced

Main

Spread Spectrum CPU Host Frequency

Actual Frequency CPU Ratio Selection SDRAM Frequency Hyper Threading Technology

Chipset Configuration Resource

Configuration Peripheral System Hardware Monitor

Configuration

AMIBIOS SETUPUTILITY -VERSION 3.31a

Security

Power

Disabled

Auto 133MHz Locked Auto Auto

Boot

Exit

[ Setup Help ]

<Enter> to enable or disable the feature of spread spectrum.

F1:Help

Esc:Exit

:Select Item :Select Menu

+/-:Change Values

Enter:Select

Sub-Menu

F9:Setup Defaults F10:Save &Exit

Spread Spectrum:

This field should always be [Disabled] for better system stability.

CPU Host Frequency:

This shows current CPU host frequency of the installed motherboard.

CPU Ratio Selection:

CPU Ratio is the multiple that times the frontside bus frequency will equal the core speed of the installed processor. Whether the option is open or locked is determined by the installed processor.

SDRAM Frequency:

If [Auto] is selected, the motherboard will detect the memory module(s) inserted and assigns appropriate frequency automatically.

Hyper-Threading Technology (for P4i45GV only):

To enable this feature, it requires a computer system with an Intel Pentium®4 processor that supports Hyper-Threading technology and an operating system that includes optimization for this technology, such as Microsoft® Windows XP. Set to [Auto] if using Microsoft® Windows® XP, or Linux kernel version

2.4.18 or higher. This option will be hidden if the current CPU does not support Hyper-Threading technology.

Chipset Configuration:

Advanced

Chipset Configuration

AGP Aperture Size Onboard VGA Share Memory ICH Delayed Transaction

USB Controller USB Device Legacy Support

CPU Thermal Throttling DRAM Write Throttling

SDRAM CAS Latency

F1:Help

Esc:Previous Menu

AMIBIOS SETUPUTILITY -VERSION 3.31a

64MB

1MB Disabled

Enabled Disabled

Enabled Enabled

Auto

:Select Item

+/-:Change Values

Enter:Select

Sub-Menu

[ Setup Help ]

<Enter> to select the size of mapped memory for graphics data.

F9:Setup Defaults F10:Save &Exit

AGP Aperture Size: It refers to a section of the PCI memory address range

used for graphics memory. We recommend that you leave this field at the default value unless your AGP card requires other sizes.

OnBoard VGA Share Memory: This allows you to select the size of share

memory for onboard VGA. Onboard VGA will get better resolution if larger size of share memory is selected. Please do not select [Disabled] if PCI graphics card is not inserted.

ICH Delayed Transaction: Select [Enabled] will enable delayed transactions

for internal register, FWH, and LPC interface accesses.

USB Controller: Use this to enable or disable the use of USB controller. USB Device Legacy Support: Use this to enable or disable support to emulate

legacy I/O devices such as mouse, keyboard,... etc.

CPU Thermal Throttling: Select [Enabled] will enable P4 thermal control

circuit to keep CPU from overheated.

DRAM Write Throttling: Select [Enabled] will enable north bridge thermal

management to keep it from overheated.

SDRAM CAS Latency:

This parameter controls the latency between the read command and the time the data available.

Resource Configuration:

Advanced

Resource Configuration

AMIBIOS SETUPUTILITY -VERSION 3.31a

[ Setup Help ]

PCI Latency Timer (PCI Clocks) Primary Graphics Adapter

F1:Help

Esc:Previous Menu

:Select Item

PCI/Int-VGA

+/-:Change Values

Enter:Select

Sub-Menu

<Enter> to select PCI clocks. Leave on default setting for the best PCI performance.

F9:Setup Defaults F10:Save &Exit

PCI Latency Timer (PCI Clocks): The default is 32. We recommend you to

keep the default value unless your PCI expansion cards’ specifications require other settings.

Primary Graphics Adapter: This allows you to select [PCI / Int-VGA], or

[Internal VGA] as the primary graphics adapter.

Peripheral Configuration:

Advanced

Peripheral Configuration

OnBoard FDC OnBoard Serial Port OnBoard Infrared Port OnBoard Parallel Port

Parallel Port Mode EPP Version Parallel Port IRQ Parallel Port DMA Channel

OnBoard Midi Port

Midi IRQ Select OnBoard Game Port OnBoard IDE OnBoard LAN OnBoard AC' 97 Audio OnBoard MC' 97 Modem

AMIBIOS SETUPUTILITY -VERSION 3.31a

Auto

Auto Disabled Auto ECP + EPP

1.9 Auto Auto Disabled 5 200H Both Enabled Auto Auto

[ Setup Help ]

<Enter> to enable or disable the floppy drive controller.

F1:Help

Esc:Previous Menu

:Select Item

+/-:Change Values

Enter:Select

Sub-Menu

F9:Setup Defaults F10:Save &Exit

OnBoard FDC: Use this to enable or disable floppy drive controller. OnBoard Serial Port: Use this to set addresses for the onboard serial ports or

disable serial ports. Configuration options: [Auto], [Disabled], [3F8 / IRQ4 / COM1], [2F8 / IRQ3 / COM2], [3E8 / IRQ4 / COM3], [2E8 / IRQ3 / COM4].

OnBoard Infrared Port: You may select [Auto] or [Disabled] for this onboard

infrared port feature.

OnBoard Parallel Port: Select Parallel Port address or disable Parallel Port.

Configuration options: [Auto], [Disabled], [378], [278]. Parallel Port Mode: Set the operation mode of the parallel port. The

default value is [ECP+EPP]. If this option is set to [ECP+EPP], it will show the EPP version in the following item, “EPP Version”.

OnBoard Midi Port: Select address for Midi Port or disable Midi Port.

Configuration options: [Disabled], [330], [300], [310], [320]. Midi IRQ Select: Use this to select Midi IRQ. Configuration options: [3], [4],

[5], [7], [10], [11].

OnBoard Game Port: Select address for Game Port or disable Game Port.

Configuration options: [Disabled], [200H], [208H], .

OnBoard IDE: You may enable either the primary IDE channel or the secondary

IDE channel. Or you may enable both the primary and the secondary IDE channels by selecting [Both]. Set to [Disabled] will disable the both. Configuration options: [Disabled], [Primary], [Secondary], [Both].

OnBoard LAN (Optional): This allows you to enable or disable the

“OnBoard LAN” feature.

OnBoard AC’97 Audio: Select [Disabled], [Auto] or [Enabled] for the onboard

AC’97 Audio feature.

OnBoard MC’97 Modem: Select [Auto] or [Disabled] for the onboard MC’97

Modem feature.

System Hardware Monitor: You can check the status of the hardware on your

system. It allows you to monitor the parameters for CPU temperature, Motherboard temperature, CPU fan speed, and critical voltage.

Advanced

System Hardware Monitor

CPU Temperature M/B

Temperature CPU FanSpeed Chassis FanSpeed Vcore

+ 3.30V + 5.00V +12.00V

F1:Help

Esc:Previous Menu

AMIBIOS SETUPUTILITY -VERSION 3.31a

35C/ 95F 27C/ 82F 3110 RPM

0RPM

1.728 V

3.312 V

4.975 V

12.167 V

:Select Item

+/-:Change Values

Enter:Select

Sub-Menu

[ Setup Help ]

F9:Setup Defaults F10:Save &Exit

2. Security Setup Menu

Advanced

Main

Supervisor Password User Password

Set Supervisor Password Set User Password

Password Check

F1:Help

Esc:Exit

AMIBIOS SETUPUTILITY -VERSION 3.31a

Security

Clear Clear

[ Enter ]

Setup

:Select Item :Select Menu

Power

+/-:Change Values

Enter:Select

Boot

Exit

Sub-Menu

[ Setup Help ]

<Enter> to set the supervisor password.

F9:Setup Defaults F10:Save &Exit

Supervisor Password: This field shows the status of the Supervisor Password.

[Clear]: No password has been set. [Set]: Supervisor password has been set.

User Password: This field shows the status of the User Password.

[Clear]: No password has been set. [Set]: User password has been set.

Set Supervisor Password: Press <Enter> to set Supervisor Password. Valid

password can be a 1 to 6 alphanumeric characters combination. If you already have a password, you must enter your current password first in order to create a new password.

Set User Password: Press <Enter> to set User Password. Valid password can

be a 1 to 6 alphanumeric characters combination. If you already have a password, you must enter your current password first in order to create a new password.

Password Check: Select the check point for “Password Check”. Configuration

options: [Setup], [Always]. If [Setup] option is selected, the “Password Check” is performed before BIOS setup. If [Always] option is selected, the “Password Check” is performed before both boot-up and BIOS setup.

3. Power Setup Menu

Advanced

Main

Suspend To RAM Repost Video on STR Resume Restore on AC / Power Loss Ring-In Power On PCI Devices Power On PS /2 keyboard Power On RTC Alarm Power On

RTC Alarm Date RTC Alarm Hour RTC Alarm Minute RTC Alarm Second

F1:Help

Esc:Exit

Security

:Select Item :Select Menu

AMIBIOS SETUPUTILITY -VERSION 3.31a

Power

Disabled

Disabled Power Off Disabled Disabled Disabled Disabled 15 12 30 30

+/-:Change Values

Enter:Select

Boot

Exit

Sub-Menu

[ Setup Help ]

<Enter> to select auto-detect or disable the ACPI STR feature.

F9:Setup Defaults F10:Save &Exit

Suspend to RAM: This field allows you to select whether to auto-detect or disable

the Suspend-to-RAM feature. Select [Auto] will enable this feature if the system supports it.

Repost Video on STR Resume: This feature allows you to repost video on STR

resume. It is recommended to enable this feature under Microsoft® Windows

98 / ME.

Restore on AC/Power Loss: This allows you to set the power state after an

unexpected AC/power loss. If [Power Off] is selected, the AC/power remains off when the power recovers. If [Power On] is selected, the AC/power resumes and the system starts to boot up when the power recovers.

Ring-In Power On: Use this to enable or disable Ring-in signals to turn on the

system from the power-soft-off mode.

PCI Devices Power On: Use this to enable or disable PCI devices to turn on the

system from the power-soft-off mode.

PS/2 Keyboard Power On: Use this to enable or disable PS/2 keyboard to turn on

the system from the power-soft-off mode.

RTC Alarm Power On: Use this to enable or disable RTC (Real Time Clock) to

power on the system. If [Enable] is selected, you must fill the RTC Alarm Date / Hour / Minute / Second sub-fields with the actual wake up time you desire.

4. Boot Setup Menu

Advanced

Main

Quick Boot Mode Boot Up Num-Lock Boot To OS/2 Boot From Network

Boot Device Priority

F1:Help

Esc:Exit

AMIBIOS SETUPUTILITY -VERSION 3.31a

Security

Enabled

On No Disabled

:Select Item :Select Menu

Power

+/-:Change Values

Enter:Select

Boot

Exit

Sub-Menu

[ Setup Help ]

<Enter> to enable or disable the quick boot mode.

F9:Setup Defaults F10:Save &Exit

Quick Boot Mode: Enable this mode will speed up the boot-up routine by skipping

memory retestings.

Boot Up Num-Lock: If this is enabled, it will automatically activate the Numeric Lock

function after boot-up.

Boot To OS/2: Select [Yes] will enable boot-up to OS/2 operating system. Boot From Network: Use this to enable or disable “boot from network” feature. Boot Device Priority: This allows you to set the boot device priority.

5. Exit Menu

Advanced

Main

Exit Saving Changes Exit Discarding Changes Load Default Settings Discard Changes

F1:Help

Esc:Exit

AMIBIOS SETUPUTILITY -VERSION 3.31a

Security

[ Enter ]

[ Enter ] [ Enter ] [ Enter ]

:Select Item :Select Menu

Power

+/-:Change Values

Enter:Select

Boot

Exit

Sub-Menu

[ Setup Help ]

Exits and saves the changesinCMOSRAM.

F9:Setup Defaults F10:Save &Exit

Exit Saving Changes: After you enter the sub-menu, the message “Save current

settings and exit” will appear. If you press <ENTER>, it will save the current settings and exit the BIOS SETUP Utility.

Exit Discarding Changes: After you enter the submenu, the message “Quit

without saving changes” will appear. If you press <ENTER>, you will exit the BIOS Setup Utility without making any changes to the settings.

Load Default Settings: After you enter the submenu, the message “Load default

settings” will appear. If you press <Enter>, it will load the default values for all the setup configuration.

Discard Changes: After you enter the sub-menu, the message “Load setup

original values” will appear. If you press <ENTER>, original values will be restored and all changes are discarded.

ASROCK P4i45GV User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual