ASRock NF6G-DVI Service Manual

ALiveNF6G-DVI

ALiveNF6G-VSTA

User Manual

Version 1.3

Published December 2006

No part of this manual may be reproduced, transcribed, transmitted, or translated in

any language, in any form or by any means, except duplication of documentation by

the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this manual may or may not be regis-

tered trademarks or copyrights of their respective companies, and are used only for

identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Disclaimer:Disclaimer:

Specifications and information contained in this manual are furnished for informa-

tional use only and subject to change without notice, and should not be constructed

as a commitment by ASRock. ASRock assumes no responsibility for any errors or

omissions that may appear in this manual.

With respect to the contents of this manual, ASRock does not provide warranty of

any kind, either expressed or implied, including but not limited to the implied warran-

ties or conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of profits, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the manual or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic

substance controlled in Perchlorate Best Management Practices (BMP) regulations

passed by the California Legislature. When you discard the Lithium battery in

California, USA, please follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see

www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

ContentsContents

Contents

ContentsContents

1.1.

IntroductionIntroduction

Introduction

1.1.

IntroductionIntroduction

1.1 Package Contents ..................................................................... 5

1.2 Specifications ........................................................................... 6

1.3 Minimum Hardware Requirement Table for Windows® Vista

Premium and Basic Logo .......................................................... 9

1.4 Motherboard Layout (ALiveNF6G-DVI) .................................... 10

1.5 Motherboard Layout (ALiveNF6G-VSTA) ................................ 11

1.6 HD 8CH I/O (ALiveNF6G-DVI / ALiveNF6G-VSTA) ................... 12

2.2.

InstallationInstallation

Installation

2.2.

InstallationInstallation

Pre-installation Precautions ............................................................... 13

2.1 CPU Installation ......................................................................... 14

2.2 Installation of CPU Fan and Heatsink ....................................... 14

2.3 Installation of Memory Modules (DIMM) .................................... 15

2.4 Expansion Slots (PCI Express, PCI, and HDMR Slots) .................... 17

2.5 Easy Dual Monitor Feature (ALiveNF6G-DVI)........................... 18

2.6 Easy Multi Monitor Feature (ALiveNF6G-DVI /

ALiveNF6G-VSTA) ................................................................... 20

2.7 Jumpers Setup .......................................................................... 21

2.8 Onboard Headers and Connectors.......................................... 22

2.9 HDMI_SPDIF Header Connection Guide .................................... 26

2.10 SATAII Hard Disk Setup Guide .................................................. 27

2.11 Serial ATA (SATA) / Serial ATAII (SATAII) Hard Disks

Installation ................................................................................. 28

2.12 Hot Plug and Hot Swap Functions for SATA / SATAII HDDs .... 28

2.13 Driver Installation Guide ............................................................ 28

2.14 HDMR Card and Driver Installation............................................ 29

2.15 Installing Windows® 2000 / XP / XP 64-bit / VistaTM /

Vista

2.16 Installing Windows® 2000 / XP / XP 64-bit / VistaTM /

Vista

2.16.1 Installing Windows® 2000 / XP / XP 64-bit With RAID

2.16.2 Installing Windows® VistaTM / Vista

2.17 Untied Overclocking Technology .............................................. 31

3.3.

BIOS SBIOS S

BIOS S

3.3.

BIOS SBIOS S

3.1 Introduction ............................................................................... 32

ETUP UTILITYETUP UTILITY

ETUP UTILITY

ETUP UTILITYETUP UTILITY

3.1.1 BIOS Menu Bar ............................................................... 32

3.1.2 Navigation Keys ............................................................. 32

........................................................................................................................

............................................................

........................................................................................................................

............................................................................................................................

..............................................................

............................................................................................................................

64-bit Without RAID Functions ..................................... 29

64-bit With RAID Functions ........................................... 29

Functions ...................................................................... 30

Functions ...................................................................... 31

......................................................................................................

...................................................

......................................................................................................

64-bit With RAID

5 5

13 13

32 32

3.2 Main Screen .............................................................................. 33

3.3 Advanced Screen .................................................................... 34

3.3.1 CPU Configuration .......................................................... 35

3.3.2 Chipset Configuration ..................................................... 38

3.3.3 ACPI Configuration ......................................................... 39

3.3.4 IDE Configuration ............................................................ 40

3.3.5 PCIPnP Configuration ...................................................... 42

3.3.6 Floppy Configuration ...................................................... 43

3.3.7 Super IO Configuration ................................................... 43

3.3.8 USB Configuration .......................................................... 44

3.4 Hardware Health Event Monitoring Screen ............................. 45

3.5 Boot Screen .............................................................................. 46

3.5.1 Boot Settings Configuration ........................................... 46

3.6 Security Screen ........................................................................ 47

3.7 Exit Screen ............................................................................... 48

4.4.

Software SupportSoftware Support

Software Support

4.4.

Software SupportSoftware Support

4.1 Install Operating System ........................................................... 49

4.2 Support CD Information ............................................................. 49

4.2.1 Running Support CD ....................................................... 49

4.2.2 Drivers Menu .................................................................. 49

4.2.3 Utilities Menu ................................................................... 49

4.2.4 Contact Information ........................................................ 49

APPENDIX: AMD’s Cool ‘n’ QuietAPPENDIX: AMD’s Cool ‘n’ Quiet

APPENDIX: AMD’s Cool ‘n’ Quiet

APPENDIX: AMD’s Cool ‘n’ QuietAPPENDIX: AMD’s Cool ‘n’ Quiet

......................................................................................................

...................................................

......................................................................................................

TMTM

T T

echnologyechnology

echnology

T T

echnologyechnology

............

......

............

49 49

50 50

1.1.

IntroductionIntroduction

Introduction

1.1.

IntroductionIntroduction

Thank you for purchasing ASRock ALiveNF6G-D VI / ALiveNF6G-VSTA motherboard,

a reliable motherboard produced under ASRock’s consistently stringent quality control.

It delivers excellent performance with robust design conforming to ASRock’s com-

mitment to quality and endurance.

In this manual, chapter 1 and 2 contain introduction of the motherboard and step-by-

step guide to the hardware installation. Chapter 3 and 4 contain the configuration

guide to BIOS setup and information of the Support CD.

Because the motherboard specifications and the BIOS software might be

updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice. You

may find the latest VGA cards and CPU support lists on ASRock website

as well. ASRock website

1.11.1

Package ContentsPackage Contents

1.1

Package Contents

1.11.1

Package ContentsPackage Contents

1 x ASRock ALiveNF6G-DVI / ALiveNF6G-VSTA Motherboard

(Micro ATX Form Factor: 9.6-in x 9.6-in, 24.4 cm x 24.4 cm)

1 x ASRock ALiveNF6G-DVI / ALiveNF6G-VSTA Quick Installation Guide 1 x ASRock ALiveNF6G-DVI / ALiveNF6G-VSTA Support CD

1 x Ultra ATA 66/100/133 IDE Ribbon Cable (80-conductor)

1 x 3.5-in Floppy Drive Ribbon Cable

1 x Serial ATA (SATA) Data Cable (Optional)

1 x Serial ATA (SATA) HDD Power Cable (Optional)

1 x HDMI_SPDIF Cable (Optional)

1 x HD 8CH I/O Shield

1 x COM Port Bracket

1 x HDMR Card (Optional) 1 x DVI Graphics-SI Card (only for ALiveNF6G-DVI)

http://www.asrock.com

1.21.2

SpecificationsSpecifications

1.2

Specifications

1.21.2

SpecificationsSpecifications

Platform - Micro ATX Form Factor: 9.6-in x 9.6-in, 24.4 cm x 24.4 cm CPU - Socket AM2 for AMD Athlon

Processors

- AMD LIVE!TM Ready

- Supports AMD’s Cool ‘n’ QuietTM Technology (see CAUTION 1)

- FSB 1000 MHz (2.0 GT/s)

- Supports Untied Overclocking Technology (see CAUTION 2)

- Supports Hyper-Transport Technology

Chipset - NVIDIA

GeForce 6150SE / nForce 430 (see CAUTION 3)

Memory - Dual Channel DDRII Memory Technology (see CAUTION 4)

- 4 x DDRII DIMM slots

- Support DDRII800/667/533

- Max. capacity: 8GB (see CAUTION 5)

Hybrid Booster - CPU Frequency Stepless Control (see CAUTION 6)

- ASRock U-COP (see CAUTION 7)

- Boot Failure Guard (B.F.G.)

- ASRock AM2 Boost: ASRock Patented Technology to boost memory performance up to 12.5% (see CAUTION 8)

Expansion Slot - 2 x PCI slots

- 1 x PCI Express x16 slot

- 1 x PCI Express x1 slot

- 1 x HDMR slot

Graphics - Integrated NVIDIA

- Pixel Shader 3.0

- Max. shared memory 256MB

- Dual VGA Output: support DVI-D and D-Sub ports with DVI

Graphics-SI card by independent display controllers (ALiveNF6G-DVI)

Audio - 7.1 CH Windows

(ALC888 Audio Codec)

LAN - Gigabit LAN 10/100/1000 Mb/s (ALiveNF6G-DVI)

- Giga PHY Realtek RTL8211B (ALiveNF6G-DVI)

- Realtek PHY RTL8201CL (ALiveNF6G-VSTA)

- Speed: 10/100 Ethernet (ALiveNF6G-VSTA )

- Supports Wake-On-LAN

Rear Panel I/O HD 8CH I/O

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

GeForce 6100 / nForce 430 or

VistaTM Premium Level HD Audio

64FX / 64X2 / 64 and Sempron

GeForce6-class graphics DX9.0 VGA

- 1 x VGA Port

- 1 x Parallel Port (ECP/EPP Support)

- 4 x Ready-to-Use USB 2.0 Ports

- 1 x RJ-45 Port

- HD Audio Jack: Side Speaker/Rear Speaker/Central/Bass/ Line in/Front Speaker/Microphone (see CAUTION 9)

Connector - 4 x Serial ATAII 3.0Gb/s connectors, support RAID (RAID 0,

RAID 1, RAID 0+1, RAID 5, JBOD), NCQ, and “Hot Plug” functions (see CAUTION 10)

- 1 x ATA133 IDE connector (supports 2 x IDE devices)

- 1 x Floppy connector

- 1 x IR header

- 1 x Game header

- 1 x COM port header

- 1 x HDMI_SPDIF header

- CPU/Chassis FAN connector

- 20 pin ATX power connector

- 4 pin 12V power connector

- CD in header

- Front panel audio connector

- 3 x USB 2.0 headers (support 6 USB 2.0 ports) (see CAUTION 11)

BIOS Feature - 4Mb AMI BIOS

- AMI Legal BIOS

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

- SMBIOS 2.3.1 Support

Support CD - Drivers, Utilities, AntiVirus Software (Trial Version) Hardware - CPU Internal Temperature Sensing Monitor - CPU Ambient Temperature Sensing

- Chassis Temperature Sensing

- CPU Fan Tachometer

- Chassis Fan Tachometer

- CPU Quiet Fan

- Voltage Monitoring: +12V, +5V, +3.3V, Vcore

OS - Microsoft

Vista

Certifications - FCC, CE, Microsoft

Windows® 2000/XP/XP 64-bit/VistaTM/

64-bit compliant (see CAUTION 12)

WHQL Certificated

WARNING

Please realize that there is a certain risk involved with overclocking, including adjusting

the setting in the BIOS, applying Untied Overclocking Technology, or using the third-

party overclocking tools. Overclocking may affect your system stability, or even

cause damage to the components and devices of your system. It should be done at

your own risk and expense. We are not responsible for possible damage caused by

overclocking.

CAUTION!

1. For power-saving’s sake, it is strongly recommended to enable AMD’s Cool ‘n’

2. This motherboard supports Untied Overclocking Technology. Please read “Un-

3. Both NVIDIA

4. This motherboard supports Dual Channel Memory Technology. Before you

5. Due to the operating system limitation, the actual memory size may be

6. Although this motherboard offers stepless control, it is not recommended to

7. While CPU overheat is detected, the system will automatically shutdown.

8. This motherboard supports ASRock AM2 Boost overclocking technology. If

technology under Windows system. See APPENDIX on page 50 to

Quiet

enable AMD’s Cool ‘n’ Quiet

technology.

tied Overclocking Technology” on page 31 for details.

GeForce 6100 / nForce 430 and GeForce 6150SE / nForce 430

refer to the same chipset. If you install NVIDIA

above under Windows

2000 / XP / XP 64-bit, or install NVIDIA® driver with

97.19 version or above under Windows

driver with 91.63 version or

VistaTM / VistaTM 64-bit, the chipset

name will be GeForce 6150SE / nForce 430 instead of GeForce 6100 / nForce

430. However, the difference in device name under Windows® does not affect

any specification and feature of this motherboard.

implement Dual Channel Memory Technology, make sure to read the

installation guide of memory modules on page 15 for proper installation.

less than 4GB for the reservation for system usage under Windows® XP

and Windows

VistaTM. For Windows® XP 64-bit and Windows® VistaTM 64-

bit with 64-bit CPU, there is no such limitation.

perform over-clocking. Frequencies other than the recommended CPU bus

frequencies may cause the instability of the system or damage the CPU.

Before you resume the system, please check if the CPU fan on the motherboard

functions properly and unplug the power cord, then plug it back again. To

improve heat dissipation, remember to spray thermal grease between the

CPU and the heatsink when you install the PC system.

you enable this function in the BIOS setup, the memory performance will

improve up to 12.5%, but the effect still depends on the AM2 CPU you adopt.

Enabling this function will overclock the chipset/CPU reference clock. However,

we can not guarantee the system stability for all CPU/DRAM configurations.

If your system is unstable after AM2 Boost function is enabled, it may not be

applicative to your system. You may choose to disable this function for

keeping the stability of your system.

9. For microphone input, this motherboard supports both stereo and mono modes.

For audio output, this motherboard supports 2-channel, 4-channel, 6-channel,

and 8-channel modes. Please check the table on page 12 for proper connection.

10. Before installing SATAII hard disk to SATAII connector, please read the “SATAII

Hard Disk Setup Guide” on page 27 to adjust your SATAII hard disk drive to

SATAII mode. You can also connect SATA hard disk to SATAII connector

directly.

11. Power Management for USB 2.0 works fine under Microsoft

VistaTM 64-bit / VistaTM / XP 64-bit / XP SP1 or SP2 / 2000 SP4.

12. Microsoft

1.31.3

Minimum Hardware RMinimum Hardware R

1.3

Minimum Hardware R

1.31.3

Minimum Hardware RMinimum Hardware R

VistaVista

Vista

VistaVista

Windows® VistaTM / VistaTM 64-bit driver keeps on updating now. As

long as we have the latest driver, we will update it to our website in the future.

Please visit our website for Microsoft® Windows® VistaTM / VistaTM 64-bit driver

and related information.

ASRock website http://www.asrock.com

equirement Tequirement T

equirement T

equirement Tequirement T

TMTM

Premium and Basic Logo Premium and Basic Logo

Premium and Basic Logo

Premium and Basic Logo Premium and Basic Logo

able for Wable for W

able for W

able for Wable for W

For system integrators and users who purchase this motherboard and

plan to submit Windows® VistaTM Premium and Basic logo, please follow the

below table for minimum hardware requirement.

CPU Sempron 2800+

Memory 512MB x 2 Dual Channel (Premium)

512MB Single Channel (Basic)

256MB x 2 Dual Channel (Basic)

Windows

indowsindows

indows

indowsindows

®®

* If you use onboard VGA with total system memory size 512MB and plan to

submit Windows® VistaTM Basic logo, please adjust the shared memory size of onboard

VGA to 64MB. If you use onboard VGA with total system memory size above 512MB

and plan to submit Windows® VistaTM Premium or Basic logo, please adjust the shared

memory size of onboard VGA to 128MB or above.

* If you plan to use external graphics card on this motherboard, please refer to Premium

Discrete requirement at

http://www.asrock.com

1.4 Motherboard Layout (ALiveNF6G-DVI)1.4 Motherboard Layout (ALiveNF6G-DVI)

1.4 Motherboard Layout (ALiveNF6G-DVI)

1.4 Motherboard Layout (ALiveNF6G-DVI)1.4 Motherboard Layout (ALiveNF6G-DVI)

243

24.4cm (9.6-in)

PS2

29 28

Mouse

Keyboard

VGA1

USB2.0 T: US B2 B:USB3

USB2.0 T: US B0 B:USB1

Bottom:

CTR BASS

MIC IN

PS2_USB_PW1

PARALLEL PORT

SIDE SPK

FRONT

Center:

AUDIO CODEC

Top: RJ-45

REAR SPK

LINE IN

HD_AUDIO1

Top:

LAN PHY

HDMI_SPDIF1

ATX12V1

COM1

ATXPWR1

PCIE1

ALiveNF6G-DVI

PCI1

PCIE2

7.1CH HD

HDMR1

PCI2

BATTERY

CMOS

CD1

PS2

Bottom:

CLRCMOS1

CPU_FAN1

PCI

EXPRESS

SOCKET AM2

FSB1GHz

RAID

NVIDIA

GeForce 6100/

nForce 430

GeForce 6150SE/

nForce 430

Chipset

RoHS

Dual CoreCPU

Dual Channel

FSB800

DDRII_1(64/72 bit, 240-pinmodule)

DDRII800

DDRII_2(64/72 bit, 240-pinmodule)

SATAII

FSB800

DDRII_3(64/72 bit, 240-pinmodule)

SATAII_4

SATAII_2

SPEAKER1

DDRII_4(64/72 bit, 240-pinmodule)

USB4_5

SATAII_3

SATAII_1

IR1

I/O

Super

IDE1

ATA133

FLOPPY1

4Mb

BIOS

CHA_FAN1

USB8_9

USB6_7

PLEDPWRBTN

HDLED RESET

GAME1

PANEL1

USB2.0

24.4cm (9.6-in)

11 12 13 14 15

1 PS2_USB_PW1 Jumper 17 USB 2.0 Header (USB6_7, Blue) 2 A TX 12V Power Connector (A TX12V1) 18 System Panel Header (PANEL1) 3 CPU Heatsink Retention Module 19 USB 2.0 Header (USB8_9, Blue) 4 AM2 940-Pin CPU Socket 20 USB 2.0 Header (USB4_5, Blue) 5 CPU Fan Connector (CPU_FAN1) 21 Chassis Speaker Header (SPEAKER 1) 6 2 x 240-pin DDRII DIMM Slots 22 Secondary SA TAII Connector (SA TAII_2, Red)

(Dual Channel A: DDRII_1, DDRII_2; Yellow) 23 NVI DIA Single Chip

7 2 x 240-pin DDRII DIMM Slots 24 Clear CMOS Jumper (CLRCMOS1)

(Dual Channel B: DDRII_3, DDRII_4; Orange) 25 HDMR Slot (HDMR1) 8 Infrared Module Header (IR1) 26 Front Panel Audio Header (HD_AUDIO1) 9 Game Port Header (GAME1) 27 HDMI_SPDIF Header (HDMI_SPDIF1) 10 Floppy Connector (FLOPPY1) 28 PCI Express x1 Slot (PCIE2) 11 Primary IDE Connector (IDE1, Blue) 29 Internal Audio Connector: CD1 (Black) 12 Flash Memory 30 PCI Slots (PCI1- 2) 13 Fourth SAT AII Connector (SATAII_4, Red) 31 PCI Express x16 Slot (PCIE1) 14 Third SAT AII Connector (SA TAII_3, Red) 32 ATX Power Connector (A TXPWR1) 15 Chassis Fan Connector (CHA_FAN1) 33 Serial Port Connector (COM1) 16 Primary SATAII Conne ctor (SA T AII_1, Red)

1010

1.5 Motherboard L1.5 Motherboard L

1.5 Motherboard L

1.5 Motherboard L1.5 Motherboard L

243

PS2

PS2_USB_PW1

Mouse

Keyboard

PARALLEL PORT

ATX12V1

COM1

Top: RJ-45

Top:

REAR SPK

Center:

SIDE SPK

Top:

LINE IN

Center:

FRONT

VGA1

USB2.0 T: US B2 B:USB3

USB2.0 T: US B0 B:USB1

Bottom:

CTR BASS

MIC IN

PS2

Bottom:

29 28

AUDIO CODEC

LAN PHY

CD1

HDMI_SPDIF1

HD_AUDIO1

PCIE2

7.1CH HD

HDMR1

ayout (ALiveNF6Gayout (ALiveNF6G

ayout (ALiveNF6G

ayout (ALiveNF6Gayout (ALiveNF6G

24.4cm (9.6-in)

CPU_FAN1

SOCKET AM2

ATXPWR1

PCIE1

ALiveNF6G-VSTA

PCI1

PCI2

CMOS

BATTERY

CLRCMOS1

PCI

EXPRESS

GeForce 6150SE/

Dual CoreCPU

FSB1GHz

RAID

NVIDIA

GeForce 6100/

nForce 430

Chipset

RoHS

VSTVST

VST

VSTVST

Dual Channel

FSB800

DDRII_2(64/72 bit, 240-pinmodule)

DDRII_1(64/72 bit, 240-pinmodule)

DDRII800

SATAII

A)A)

FSB800

DDRII_3(64/72 bit, 240-pinmodule)

SATAII_4

SATAII_2

SPEAKER1

DDRII_4(64/72 bit, 240-pinmodule)

USB4_5

SATAII_3

SATAII_1

IR1

I/O

Super

GAME1

IDE1

ATA133

FLOPPY1

4Mb

BIOS

CHA_FAN1

USB8_9

USB6_7

PLEDPWRBTN

PANEL1

HDLED RESET

USB2.0

24.4cm (9.6-in)

11 12 13 14 15

1 PS2_USB_PW1 Jumper 17 USB 2.0 Header (USB6_7, Blue) 2 A TX 12V Power Connector (A TX12V1) 18 System Panel Header (P ANEL1) 3 CPU Heatsink Retention Module 19 USB 2.0 Header (USB8_9, Blue) 4 AM2 940-Pin CPU Socket 20 USB 2.0 Header (USB4_5, Blue) 5 CPU Fan Connector (CPU_FAN1) 21 Chassis Speaker Header (SPEAKER 1) 6 2 x 240-pin DDRII DIMM Slots 22 Secondary SA TAII Connector (SA TAII_2, Red)

(Dual Channel A: DDRII_1, DDRII_2; Yellow) 23 NVI DIA Single Chip

7 2 x 240-pin DDRII DIMM Slots 24 Clear CMOS Jumper (CLRCMOS1)

(Dual Channel B: DDRII_3, DDRII_4; Orange) 25 HDMR Slot (HDMR1) 8 Infrared Module Header (IR1) 26 Front Panel Audio Header (HD_AUDIO1) 9 Game Port Header (GAME1) 27 HDMI_SPDIF Header (HDMI_SPDIF1) 10 Floppy Connector (FLOPPY1) 28 PCI Express x1 Slot (PCIE2) 11 Primary IDE Connector (IDE1, Blue) 29 Internal Audio Connector: CD1 (Black) 12 Flash Memory 30 PCI Slots (PCI1- 2) 13 Fourth SAT AII Connector (SATAII_4, Red) 31 PCI Express x16 Slot (PCIE1) 14 Third SAT AII Connector (SA TAII_3, Red) 32 ATX Power Connector (A TXPW R1) 15 Chassis Fan Connector (CHA_FAN1) 33 Serial Port Connector (COM1) 16 Primary SAT AII Connector (SA T AII_1, Red)

1111

1.61.6

HD 8CH I/O (ALiveNF6GHD 8CH I/O (ALiveNF6G

1.6

HD 8CH I/O (ALiveNF6G

1.61.6

HD 8CH I/O (ALiveNF6GHD 8CH I/O (ALiveNF6G

-D-D

VI / ALiveNF6GVI / ALiveNF6G

-D

VI / ALiveNF6G

-D-D

VI / ALiveNF6GVI / ALiveNF6G

VSTVST

VST

VSTVST

A)A)

1213

1 Parallel Port 8 Microphone (Pink) 2 RJ-45 Port 9 USB 2.0 Ports (USB01) 3 Side Speaker (Gray) 10 USB 2.0 Ports (USB23) 4 Rear Speaker (Black) 11 VG A Port 5 Central / Bass (Orange) 12 PS/2 Keyboard Port (Purple) 6 Line In (Light Blue) 13 PS/2 Mouse Port (Green)

*7 Front Speaker (Lime)

* If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”. See

the table below for connection details in accordance with the type of speaker you use.

Audio Output Channels Front Speaker Rear Speaker Central / Bass Side Speaker

2 V -- -- --

4VV----

6VVV--

8VVVV

TABLE for Audio Output Connection

(No. 7) (No. 4) (No. 5) (No. 3)

* To enable Multi-Streaming function, you need to connect a front panel audio cable to the front

panel audio header. After restarting your computer, you will find “Mixer” tool on your system.

Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click

“ok”. Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA

Primary output” to use Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek HDA

Audio 2nd output” to use front panel audio.

1212

2.2.

InstallationInstallation

Installation

2.2.

InstallationInstallation

This is a Micro ATX form factor (9.6-in x 9.6-in, 24.4 cm x 24.4 cm) motherboard.

Before you install the motherboard, study the configuration of your chassis to en-

sure that the motherboard fits into it.

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Pre-installation PrecautionsPre-installation Precautions

Take note of the following precautions before you install motherboard

components or change any motherboard settings.

Before you install or remove any component, ensure that the

power is switched off or the power cord is detached from the

power supply. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

1. Unplug the power cord from the wall socket before touching any

component.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the carpet or

the like. Also remember to use a grounded wrist strap or touch a

safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded anti-

static pad or in the bag that comes with the component.

5. When placing screws into the screw holes to secure the motherboard

to the chassis, please do not over-tighten the screws! Doing so may

damage the motherboard.

1313

2.12.1

CPU InstallationCPU Installation

2.1

CPU Installation

2.12.1

CPU InstallationCPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90

angle.

Step 2. Position the CPU directly above the socket such that the CPU corner with

the golden triangle matches the socket corner with a small triangle.

Step 3. Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the CPU

into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push

down the socket lever to secure the CPU. The lever clicks on the side tab

to indicate that it is locked.

Lever 90° Up

STEP 1: Lift Up The Socket Lever

2.22.2

Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink

2.2

Installation of CPU Fan and Heatsink

2.22.2

Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink

CPU Golden Triangle

Socket Corner

STEP 2 / STEP 3: Match The CPU Golden Triangle To The Socket Corner

STEP 4: Push Down And Lock The Socket Lever

After you install the CPU into this motherboard, it is necessary to install a

larger heatsink and cooling fan to dissipate heat. You also need to spray

thermal grease between the CPU and the heatsink to improve heat

dissipation. Make sure that the CPU and the heatsink are securely fas-

tened and in good contact with each other. Then connect the CPU fan to

the CPU FAN connector (CPU_FAN1, see Page 10 / 11, No. 5). For proper

installation, please kindly refer to the instruction manuals of the CPU fan

and the heatsink.

1414

2.3 Installation of Memory Modules (DIMM)2.3 Installation of Memory Modules (DIMM)

2.3 Installation of Memory Modules (DIMM)

2.3 Installation of Memory Modules (DIMM)2.3 Installation of Memory Modules (DIMM)

This motherboard provides four 240-pin DDRII (Double Data Rate II) DIMM slots,

and supports Dual Channel Memory Technology. For dual channel configuration, you always need to install identical (the same brand, speed, size and chip-

type) DDRII DIMM pair in the slots of the same color. In other words, you have to install identical DDRII DIMM pair in Dual Channel A (DDRII_1 and DDRII_2; Yellow slots; see p.10/p.11 No.6) or identical DDRII DIMM pair in Dual Channel B (DDRII_3 and DDRII_4; Orange slots; see p.10/p.11 No.7), so that Dual Channel

Memory Technology can be activated. This motherboard also allows you to install four DDRII DIMMs for dual channel configuration, and please install iden- tical DDRII DIMMs in all four slots. You may refer to the Dual Channel Memory

Configuration Table below.

Dual Channel Memory Configurations

DDRII_1 DDRII_2 DDRII_3 DDRII_4

(Yellow Slot) (Yellow Slot) (Orange Slot) (Orange Slot)

(1) Populated Populated - -

(2) - - Populated Populated

(3)* Populated Populated Populated Populated

* For the configuration (3), please install identical DDRII DIMMs in all four slots.

1. If you want to install two memory modules, for optimal compatibility

and reliability, it is recommended to install them in the slots of the

same color. In other words, install them either in the set of yellow

slots (DDRII_1 and DDRII_2), or in the set of orange slots (DDRII_3

and DDRII_4).

2. If only one memory module or three memory modules are installed

in the DDRII DIMM slots on this motherboard, it is unable to activate

the Dual Channel Memory Technology.

3. If a pair of memory modules is NOT installed in the same Dual

Channel, for example, installing a pair of memory modules in DDRII_1

and DDRII_3, it is unable to activate the Dual Channel Memory

Technology .

4. It is not allowed to install a DDR memory module into DDRII slot;

otherwise, this motherboard and DIMM may be damaged.

1515

+ 35 hidden pages