ASRock J4105M operation manual

Page 1
Page 2
Version 1.0 Published November 2017 Copyright©2017 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.
infringe.
Disclaimer:
Specications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or tness for a particular purpose.
In no event shall ASRock, its directors, ocers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of prots, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/ perchlorate”
ASRock Website: http://www.asrock.com
Page 3
AUSTRALIA ONLY
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage caused by our goods. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. If you require assistance please call ASRock Tel : +886-2-28965588 ext.123 (Standard International call charges apply)
e terms HDMI™ and HDMI High-Denition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
Page 4
Contents
Chapter 1 Introduction 1
1.1 Package Contents 1
1.2 Specications 2
1.3 Motherboard Layout 5
1.4 I/O Panel 7
Chapter 2 Installation 9
2.1 Installing Memory Modules (DIMM) 10
2.2 Expansion Slots (PCI Express Slots) 12
2.3 Jumpers Setup 13
2.4 Onboard Headers and Connectors 14
2.5 Intel® CNVi (Integrated WiFi/BT) Installation Guide 18
Chapter 3 Software and Utilities Operation 20
3.1 Installing Drivers 20
3.2 ASRock Live Update & APP Shop 21
3.2.1 UI Overview 21
3.2.2 Apps 22
3.2.3 BIOS & Drivers 25
3.2.4 Setting 26
Chapter 4 UEFI SETUP UTILITY 27
4.1 Introduction 27
4.1.1 UEFI Menu Bar 27
4.1.2 Navigation Keys 28
Page 5
4.2 Main Screen 29
4.3 Advanced Screen 30
4.3.1 CPU Conguration 31
4.3.2 Chipset Conguration 32
4.3.3 Storage Conguration 34
4.3.4 Super IO Conguration 35
4.3.5 ACPI Conguration 36
4.3.6 USB Conguration 38
4.4 Tools 39
4.5 Hardware Health Event Monitoring Screen 41
4.6 Security Screen 42
4.7 Boot Screen 43
4.8 Exit Screen 45
Page 6
Chapter 1 Introduction
ank you for purchasing ASRock J4105M / J4005M motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance.
In this manual, Chapter 1 and 2 contains the introduction of the motherboard and step-by-step installation guides. Chapter 3 contains the operation guide of the soware and utilities. Chapter 4 contains the conguration guide of the BIOS setup.
Becau se the motherboard specications and the BIOS soware might be updated, the content of this documentation will be subject to change without notice. In case any modications of this documentation occur, the updated version will be available on ASRock’s website w ithout f urther notice. If you require technical support relate d to this motherboard, please vi sit our website for s pecic information about the model you are using. You may nd the l atest VGA cards and CPU suppor t list on ASRock’s website a s well. ASRock website ht tp://www.a srock.com.
1.1 Package Contents
ASRock J4105M / J4005M Motherboard (Micro ATX Form Factor)
•
ASRock J4105M / J4005M Quick Installation Guide
•
ASRock J4105M / J4005M Support CD
•
2 x Serial ATA (SATA) Data Cables (Optional)
•
1 x Screw for M.2 Socket (Optional)
•
1 x I/O Panel Shield
•
J4105M J4005M
English
1
Page 7
1.2 Specications
Platform
CPU
Memory
Expansion Slot
•
•
•
•
•
•
* 2GB DRAM per module is not supported.
•
•
* Intel® Extreme Memory Prole (XMP) is not supported
•
•
•
* M.2 PCI Express module is not supported
Micro ATX Form Factor Solid Capacitor design
Intel® Quad-Core Processor J4105 (up to 2.5 GHz)
(for J4105M)
Intel® Dual-Core Processor J4005 (up to 2.7 GHz)
(for J4005M)
Dual Channel DDR4 Memory Technology 2 x DDR4 DIMM Slots
Supports DDR4 2400/2133 non-ECC, un-buered memory Max. capacity of system memory: 8GB
1 x PCI Express 2.0 x16 Slot (PCIE2: x1 mode) 2 x PCI Express 2.0 x1 Slots 1 x M.2 Socket (Key E), supports type 2230 Intel® CNVi (Integrated WiFi/BT)
English
2
Graphics
• Integrated Intel® UHD Graphics 600: 12 EUs inside (Up to 750MHz) (for J4105M)
• Integrated Intel® UHD Graphics 600: 12 EUs inside (Up to 700MHz) (for J4005M)
• DX12, OpenGL 4.3, OGL ES 3.0, OpenCL 2.0
• HW Acceleration Decode: HEVC (H.265) 8 bit, HEVC
(H.265)10 bit, H.264 @ Lvl5.2 (AVC), JPEG/MJPEG, VP8, VP9 8bit, VP9 10 bit
• HW Acceleration Encode: HEVC (H.265) 8 bit, HEVC (H.265)10 bit, H.264 @ Lvl5.2 (AVC), JPEG/MJPEG, VP8, VP9 8bit
• ree graphics output options: D-Sub, DVI-D and HDMI
• Supports Triple Monitor
• Supports HDMI with max. resolution up to 4K x 2K
(4096x2160) @ 60Hz
• Supports DVI-D with max. resolution up to 1920x1200 @ 60Hz
Page 8
Audio
LAN
• Supports D-Sub with max. resolution up to 2048x1536 @ 60Hz
• Supports Auto Lip Sync, xvYCC and HBR (High Bit Rate Audio) with HDMI Port (Compliant HDMI monitor is required)
• Supports HDCP with DVI-D and HDMI Ports
• Supports Full HD 1080p Blu-ray (BD) playback with DVI-D
and HDMI Ports
7.1 CH HD Audio (Realtek ALC887 Audio Codec)
•
* To congure 7.1 CH HD Audio, it is required to use an HD front panel audio module and enable the multi-channel audio feature through the audio driver.
Supports Surge Protection
•
ELNA Audio Caps
•
PCIE x1 Gigabit LAN 10/100/1000 Mb/s
•
Realtek RTL8111E
•
Supports Wake-On-LAN
•
Supports Lightning/ESD Protection
•
Supports Energy Ecient Ethernet 802.3az
•
Supports PXE
•
J4105M J4005M
Rear Panel I/O
Storage
1 x PS/2 Mouse Port
•
1 x PS/2 Keyboard Port
•
1 x D-Sub Port
•
1 x DVI-D Port
•
1 x HDMI Port
•
2 x USB 2.0 Ports (Supports ESD Protection)
•
2 x USB 3.1 Gen1 Ports (Supports ESD Protection)
•
1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED
•
LED) HD Audio Jacks: Line in / Front Speaker / Microphone
•
2 x SATA3 6.0 Gb/s Connectors, support NCQ, AHCI and
•
Hot Plug
English
3
Page 9
Connector
BIOS Feature
Hardware Monitor
1 x Print Port Header
•
2 x COM Port Headers
•
1 x Chassis Intrusion and Speaker Header
•
1 x CPU Fan Connector (3-pin)
•
1 x Chassis Fan Connector (3-pin)
•
1 x 24 pin ATX Power Connector
•
1 x Front Panel Audio Connector
•
3 x USB 2.0 Headers (Support 5 USB 2.0 ports) (Supports ESD
•
Protection) 1 x USB 3.1 Gen1 Header (Supports 2 USB 3.1 Gen1 ports)
•
(Supports ESD Protection)
AMI UEFI Legal BIOS with GUI support
•
Supports Plug and Play
•
ACPI 5.0 compliant wake up events
•
Supports jumperfree
•
SMBIOS 3.0 support
•
CPU/Chassis temperature sensing
•
CPU/Chassis Fan Tachometer
•
CPU/Chassis Quiet Fan (Auto adjust chassis fan speed by
•
CPU temperature) CPU/Chassis Fan multi-speed control
•
CASE OPEN detection
•
Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore
•
English
4
Microso® Windows® 10 64-bit
OS
Certica­tions
* For detailed product information, please visit our website: http://ww w.asrock.com
•
FCC, CE
•
ErP/EuP ready (ErP/EuP ready power supply is required)
•
Page 10

1.3 Motherboard Layout

PCIE 1
ATXP WR 1
13
12
AUDIO CODEC
1
9
Sup er
I/O
3
PS2
Key boa rd
PS2
Mou se
CPU_FAN 1
1
USB_2_ 3
HDLED RESET
PLED PW RBTN
PANEL1
1
1
COM2
1
SATA3_2
CMO S
Bat te ry
Ro HS
1
HD_AU DIO1
2
4
5
6
7
BIOS ROM
Fr on t US B 3 .0
LAN
CLRMOS1
1
USB3_ 1_2
SATA3_1
Top: RJ-4 5
USB 2.0 T: US B0 B: USB1
Top:
LINE IN
Cente r:
FRONT
Botto m:
MIC IN
USB 3 .1 G en1 T: USB0 B: US B1
HDM I1
PCIE 2
PCIE 3
DVI 1
VGA 1
1
LPT1
DDR 4_A 2 ( 64 bit, 288 -pi n m od u le )
DDR 4_A 1 ( 64 bit, 288 -pi n m od u le )
COM1
1
1
USB_4_ 5
USB_6
SPK_CI1
1
CNV I1
CNVI1_CT 1
J4105M J4005M
English
5
Page 11
No. Description
1 Clear CMOS Jumper (CLRMOS1)
2 CPU Fan Connector (CPU_FAN1)
3 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_A2)
4 ATX Power Connector (ATXPWR1)
5 SATA3 Connector (SATA3_1)
6 SATA3 Connector (SATA3_2)
7 USB 3.1 Gen1 Header (USB3_1_2)
8 System Panel Header (PANEL1)
9 Chassis Fan Connector (CHA_FAN1)
10 Chassis Intrusion and Speaker Header (SPK_CI1)
11 USB 2.0 Header (USB_4_5)
12 USB 2.0 Header (USB_2_3)
13 USB 2.0 Header (USB_6)
14 Print Port Header (LPT1)
15 COM Port Header (COM1)
16 COM Port Header (COM2)
17 Front Panel Audio Header (HD_AUDIO1)
English
6
Page 12

1.4 I/O Panel

1
J4105M J4005M
3
2
4
10
No. Description No. Description
1 PS/2 Mouse Port 7 USB 3.1 Gen1 Ports (USB3_01)
2 LAN RJ-45 Port* 8 HDMI Port
3 Line In (Light Blue)** 9 DVI-D Port
4 Front Speaker (Lime)** 10 D-Sub Port
5 Microphone (Pink)** 11 PS/2 Keyboard Port
6 USB 2.0 Ports (USB01)
* ere are two LEDs on the LAN port. Please refer to the table below for the LAN port LED indications.
ACT/LINK L ED
SPEED LE D
LAN Por t
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 10Mbps connection Blinking Data Activity Orange 100Mbps connection On Link Green 1Gbps connection
8 7
56911
English
7
Page 13
** To congure 7.1 CH HD Audio, it i s required to use an HD front panel audio module and enable the multi­channel audio feature through the audio driver.
Please set Speaker Conguration to “7.1 Speaker”in the Realtek HD Audio Manager.
Function of the Audio Por ts in 7.1-channel Con guration:
English
8
Port Function
Light Blue (Rear panel) Rear Speaker Out Lime (Rear panel) Front Speaker Out Pink (Rear panel) Central /Subwoofer Speaker Out Lime (Front panel) Side Speaker Out
Page 14

Chapter 2 Installation

is is a Micro ATX form factor motherboard. Before you install the motherboard, study the conguration of your chassis to ensure that the motherboard ts into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components or change any motherboard settings.
Make sure to unplug the power cord before installing or removing the motherboard.
•
Failure to do so may cause physical injuries to you and damages to motherboard components. In order to avoid damage from static electricity to the motherboard’s components,
•
NEVER place your motherboard directly on a carpet. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle the components. Hold components by the edges and do not touch the ICs.
•
Whenever you uninstall any components, place them on a grounded anti-static pad or
•
in the bag that comes with the components. When placing screws to secure the motherboard to the chassis, please do not over-
•
tighten the screws! Doing so may damage the motherboard.
J4105M J4005M
English
9
Page 15
2.1 Installing Memory Modules (DIMM)
This motherboard provides two 288-pin DDR4 (Double Data Rate 4) DIMM slots, and supports Dual Channel Memory Technology.
1. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4 slot; otherwise, this motherboard and DIMM may be damaged.
2. e DI MM only ts in one correct orientation. It will cause per manent damage to the mothe rboard and the DIMM if you force the DIMM into the slot at incor rect orientation .
Supported DDR4 Non ECC DIMM
Raw Card
A (1Rx8) B (2Rx8) C (1Rx16)
Dual Channel Memory Conguration
English
10
DDR4_ A1
DDR4_ A2
Populated
Populated
Page 16
J4105M J4005M
1
2
3
English
11
Page 17
2.2 Expansion Slots (PCI Express Slots)
ere are 3 PCI Express slots on the motherboard.
Before installing an ex pansion card, please make sure that the power supply is switched o or the power cord is unplugged. Plea se read the documentation of the expan sion card and mak e necessary hardware settings for the card before you start the installation.
PCIe slot:
PCIE1 (PCIe 2.0 x1 slot) is used for PCI Express x1 lane width cards. PCIE2 (PCIe 2.0 x16 slot) is used for PCI Express x1 lane width cards. PCIE3 (PCIe 2.0 x1 slot) is used for PCI Express x1 lane width cards.
Warning:
To ensure better graphics compability, the BIOS is set to "boot from Onboard VGA" as default even the user install a VGA card on PCIe slot.
English
12
Page 18

2.3 Jumpers Setup

e illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is “Open”. e illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”
when a jumper cap is placed on these 2 pins.
Clear CMOS Jumper (CLRMOS1) (see p.5, No. 1)
CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn o the computer and unplug the power cord from the power supply. Aer waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRMOS1 for 5 seconds. However, please do not clear the CMOS right aer you update the BIOS. If you need to clear the CMOS when you just nish updating the BIOS, you must boot up the system rst, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, and user default prole will be cleared only if the CMOS battery is removed.
Clear CMOSDefault
J4105M J4005M
If you clear the CMOS, the case open may be detec ted. Please adjust the BIOS option “Clear Status” to clear the record of previou s chassis intrusion status.
English
13
Page 19

2.4 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these header s and connectors. Placing jumper caps over the headers and connectors will cause permanent damage to the motherboard.
System Panel Header (9-pin PANEL1) (see p.5, No. 8)
PWRBTN (Power Switch):
Connec t to the power switch on the chassi s front panel. You may congure the way to turn o your system using the power switch.
RESET (Reset Switch):
Connec t to the reset switch on the chassi s front panel. P ress the reset sw itch to restart the computer if the compute r freezes and fails to perform a normal restart.
PLED (Syste m Power LED):
Connec t to the power status indicator on the chassis front panel. e LED i s on when the system is ope rating. e LED keeps blinking when the system i s in S1/S3 sleep state. e LED is o when the system i s in S4 sle ep state or powered o (S5).
HDLED (Ha rd Drive Activity LED):
Connec t to the hard drive ac tivity LED on the chassis front panel. e LED is on when the hard dr ive is reading or w riting data.
e front panel de sign may dier by chassis. A front pane l module mainly consists of power switch , reset switch, power LED, hard dr ive activity LED, speak er and etc. When connecting your chassis front panel module to this head er, make sure the wire assig nments and the pin assig nments are matched correctly.
1
PLE D+
PLE D-
HDL ED-
HDL ED+
PWR BTN #
GND
GND
RES ET#
GND
Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.
English
14
Chassis Intrusion and Speaker Header (7-pin SPK_CI1) (see p.5, No. 10)
DUM MY +5V
1
SIG NAL
SPE AKE R
DUM MY
GND
DUM MY
Please connect the chassis intrusion and the chassis speaker to this header.
Page 20
J4105M
IntA _P_D +
J4005M
Serial ATA3 Connectors (SATA3_1: see p.5, No. 5) (SATA3_2: see p.5, No. 6)
USB 2.0 Headers (9-pin USB_2_3) (see p.5, No. 12) (9-pin USB_4_5) (see p.5, No. 11)
(9-pin USB_6) (see p.5, No. 13)
USB 3.1 Gen1 Header (19-pin USB3_1_2) (see p.5, No. 7)
1
IntA _P_D -
IntA _P_D +
ID
USB _PW R
1
USB _PW R
1
USB _PW R
GND
IntA _P_D -
SATA3_1
SATA3_2
P-
P+
GND
GND
P+
P-
P-
P+
IntA _P_S STX +
IntA _P_S STX -
GND
IntA _P_S SRX +
IntA _P_S STX -
IntA _P_S STX +
GND
DUM MY
GND
IntA _P_ SSRX -
IntA _P_S SRX +
GND
Vbus
Vbus
IntA _P_ SSRX -
ese two SATA3 connectors support SATA data cables for internal storage devices with up to
6.0 Gb/s data transfer rate.
ere are three headers on this motherboard.
ere is one header on this motherboard. is USB 3.1 Gen1 header can support two ports.
Front Panel Audio Header (9-pin HD_AUDIO1) (see p.5, No. 17)
1
GND
PRE SEN CE#
MIC 2_R
MIC 2_L
MIC _RE T
J_S ENS E
OUT 2_R
OUT _RE T
OUT 2_L
is header is for connecting audio devices to the front audio panel.
English
15
Page 21
1. High Denition Audio supports Jack Sensing, but the panel w ire on the chassis must
CPU_ FAN_ SPE ED
suppor t HDA to function correctly. Please follow the instructions in our manual and chassis manual to install your syste m.
2. If you use an AC’97 audio panel, please install it to the f ront panel audio header by the steps below: A. Connect Mic_IN (MIC) to MIC2_ L. B. Conne ct Audio_R (RIN) to OUT2_R and Audio_ L (LIN) to OUT2_ L. C. Connect Ground (GND) to Ground (GND). D. MIC_ RET and OUT_RET are for the HD audio panel only. You don’t need to connec t them for the AC’97 audio panel. E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel and adju st “Recording Volume”.
English
Chassis Fan Connector (3-pin CHA_FAN1) (see p.5, No. 9)
CPU Fan Connector (3-pin CPU_FAN1) (see p.5, No. 2)
ATX Power Connector (24-pin ATXPWR1) (see p.5, No. 4)
Serial Port Headers (9-pin COM1) (see p.5, No. 15) (9-pin COM2) (see p.5, No. 16)
Please connect fan cable to the fan connector and match the black wire to the ground pin.
Please connect the CPU fan cable to the connector and match the black wire to the ground pin.
12
24
is motherboard pro­vides a 24-pin ATX power connector. To use a 20-pin ATX power supply, please plug it along Pin 1 and Pin
1
13
13.
is header supports a serial port module.
16
Page 22
J4105M
STB #
J4005M
Print Port Header (25-pin LPT1) (see p.5, No. 14)
SLCT
SPD 2
SPD 7
GND
SPD 6
SPD 5
SPD 4
SPD 3
SLIN #
PINI T#
ERRO R#
PE
BUS Y
ACK#
for print port cable that allows convenient
1
connection of printer devices.
AFD #
is is an interface
SPD 0
SPD 1
English
17
Page 23
2.5 Intel® CNVi (Integrated WiFi/BT) Installation Guide
e M.2, also known as the Next Generation Form Factor (NGFF), is a small size and versatile card edge connector that aims to replace mPCIe and mSATA. e M.2 Socket (Key E) supports type 2230 Intel® CNVi (Integrated WiFi/BT).
Installing Intel® CNVi (Integrated WiFi/BT)
Step 1
Prepare a type 2230 Intel® CNVi (Integrated WiFi/BT) and the screw.
Step 2
Find the nut location to be used.
PCB Length: 3cm Module Type: Type2230
English
18
A
Step 3
Gently insert the type 2230 Intel® CNVi (Integrated WiFi/BT) into the M.2 slot. Please be aware that the module only ts in one orientation.
A
o
A
20
Page 24
J4105M J4005M
Step 4
Tighten the screw with a screwdriver to secure the module into place. Please do not overtighten the screw as this might damage the module.
A
19
English
Page 25
Chapter 3 Software and Utilities Operation
3.1 Installing Drivers
e Support CD that comes with the motherboard contains necessary drivers and useful utilities that enhance the motherboard’s features.
Running The Support CD
To begin using the support CD, insert the CD into your CD-ROM drive. e CD automatically displays the Main Menu if “AUTORUN” is enabled in your computer. If the Main Menu does not appear automatically, locate and double click on the le “ASRSETUP.EXE” in the Support CD to display the menu.
Drivers Menu
e drivers compatible to your system will be auto-detected and listed on the support CD driver page. Please click Instal l All or follow the order from top to bottom to install those required drivers. erefore, the drivers you install can work properly.
Utilities Menu
e Utilities Menu shows the application soware that the motherboard supports. Click on a specic item then follow the installation wizard to install it.
English
20
Page 26
3.2 ASRock Live Update & APP Shop
e ASRock Live Update & APP Shop is an online store for purchasing and downloading soware applications for your ASRock computer. You can quickly and easily install various apps and support utilities. With ASRock Live Update & APP Shop, you can optimize your system and keep your motherboard up to date simply with a few clicks.
Double-click on your desktop to access ASRock Live Update & APP Shop utility.
*You need to be connected to the Internet to download apps f rom the ASRock Live Update & APP Shop.

3.2.1 UI Overview

J4105M J4005M
Category Panel
Information Panel
Category Panel: e category panel contains several category tabs or buttons that when selected the information panel below displays the relative information.
Information Panel: e information panel in the center displays data about the currently selected category and allows users to perform job-related tasks.
Hot News: e hot news section displays the various latest news. Click on the image to visit the website of the selected news and know more.
Hot News
English
21
Page 27

3.2.2 Apps

When the "Apps" tab is selected, you will see all the available apps on screen for you to download.
Installing an App
Step 1
Find the app you want to install.
e most recommended app appears on the le side of the screen. e other various apps are shown on the right. Please scroll up and down to see more apps listed.
English
22
You can check the price of the app and whether you have already intalled it or not.
- e red icon displays the price or "Free" if the app is free of charge.
- e green "Installed" icon means the app is installed on your computer.
Step 2
Click on the app icon to see more details about the selected app.
Page 28
Step 3
If you want to install the app, click on the red icon to start downloading.
Step 4
When installation completes, you can nd the green "Installed" icon appears on the upper right corner.
J4105M J4005M
To uninstall it, simply click on the trash can icon . *e trash icon may not appear for certain apps.
English
23
Page 29
Upgrading an App
You can only upgrade the apps you have already installed. When there is an available new version for your app, you will nd the mark of "New Version" appears below the installed app icon.
Step 1
Click on the app icon to see more details.
Step 2
Click on the yellow icon to start upgrading.
English
24
Page 30

3.2.3 BIOS & Drivers

Installing BIOS or Drivers
When the "BIOS & Drivers" tab is selected, you will see a list of recommended or critical updates for the BIOS or drivers. Please update them all soon.
J4105M J4005M
Step 1
Please check the item information before update. Click on to see more details.
Step 2
Click to select one or more items you want to update.
Step 3
Click Update to start the update process.
English
25
Page 31

3.2.4 Setting

In the "Setting" page, you can change the language, select the server location, and determine if you want to automatically run the ASRock Live Update & APP Shop on Windows startup.
English
26
Page 32

Chapter 4 UEFI SETUP UTILITY

4.1 Introduction

is section explains how to use the UEFI SETUP UTILITY to congure your system. You may run the UEFI SETUP UTILITY by pressing <F2> or <Del> right aer you power on the computer, otherwise, the Power-On-Self-Test (POST) will continue with its test routines. If you wish to enter the UEFI SETUP UTILITY aer POST, restart the system by pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system chassis. You may also restart by turning the system o and then back on.
Becau se the UEFI soware is constantly being upd ated, the following UEFI setup screens and de scriptions are for reference purpose only, and they may not exactly match what you see on your scre en.

4.1.1 UEFI Menu Bar

e top of the screen has a menu bar with the following selections:
J4105M J4005M
Main
Advanced
Tool
H/W Monitor
Security
Boot
Exit
For setting system time/date information
For advanced system congurations
Useful tools
Displays current hardware status
For security settings
For conguring boot settings and boot priority
Exit the current screen or the UEFI Setup Utility
English
27
Page 33

4.1.2 Navigation Keys

Use < > key or < > key to choose among the selections on the menu bar, and use < > key or < > key to move the cursor up or down to select items, then press <Enter> to get into the sub screen. You can also use the mouse to click your required item.
Please check the following table for the descriptions of each navigation key.
Navigation Key(s) Description
+ / -
<Tab>
<PGUP>
<PGDN>
<HOME>
<END>
<F1>
<F7>
<F9>
<F10>
<F12>
<ESC>
To change option for the selected items
Switch to next function
Go to the previous page
Go to the next page
Go to the top of the screen
Go to the bottom of the screen
To display the General Help Screen
Discard changes and exit the SETUP UTILITY
Load optimal default values for all the settings
Save changes and exit the SETUP UTILITY
Print screen
Jump to the Exit Screen or exit the current screen
English
28
Page 34

4.2 Main Screen

When you enter the UEFI SETUP UTILITY, the Main screen will appear and display the system overview.
J4105M:
J4105M J4005M
J4005M:
English
29
Page 35

4.3 Advanced Screen

In this section, you may set the congurations for the following items: CPU Conguration, Chipset Conguration, Storage Conguration, Super IO Con­guration, ACPI Conguration and USB Conguration.
Setting wrong values in this sec tion may cause the system to malfunction.
English
30
Page 36
4.3.1 CPU Conguration
Intel SpeedStep Technology
Intel SpeedStep technology allows processors to switch between multiple frequencies and voltage points for better power saving and heat dissipation.
J4105M J4005M
CPU C States Support
Enable CPU C States Support for power saving. It is recommended to keep C1 and C6 all enabled for better power saving.
Enhanced Halt State (C1E)
Enable Enhanced Halt State (C1E) for lower power consumption.
Intel Turbo Boost Technology
Intel Turbo Boost Technology enables the processor to run above its base operating frequency when the operating system requests the highest performance state.
VT-d
Intel® Virtualization Technology for Directed I/O helps your virtual machine monitor better utilize hardware by improving application compatibility and reliability, and providing additional levels of manageability, security, isolation, and I/O performance.
English
31
Page 37
4.3.2 Chipset Conguration
DRAM Voltage
Use this to congure DRAM Voltage. e default value is [Auto].
Primary Graphics Adapter
Select a primary VGA.
English
32
Share Memory
Congure the size of memory that is allocated to the integrated graphics processor when the system boots up.
Onboard HD Audio
Enable/disable onboard HD audio. Set to Auto to enable onboard HD audio and automatically disable it when a sound card is installed.
Front Panel
Enable/disable front panel HD audio.
Onboard LAN
Enable or disable the onboard network interface controller.
PCIE1 Link Speed
Select the link speed for PCIE1.
Page 38
ASPM
is option enables/disables the ASPM support.
PCIE2 Link Speed
Select the link speed for PCIE2.
ASPM
is option enables/disables the ASPM support.
PCIE3 Link Speed
Select the link speed for PCIE3.
ASPM
is option enables/disables the ASPM support.
Deep Sleep
Congure deep sleep mode for power saving when the computer is shut down.
Restore on AC/Power Loss
Select the power state aer a power failure. If [Power O] is selected, the power will remain o when the power recovers. If [Power On] is selected, the system will start to boot up when the power recovers.
J4105M J4005M
33
English
Page 39
4.3.3 Storage Conguration
SATA Controller(s)
Enable/disable the SATA controllers.
SATA Mode Selection
AHCI: Supports new features that improve performance.
English
34
AHCI (Advanc ed Host Controll er Interface) supports NCQ and other new feature s that will improve SATA disk per formance.
SATA Aggressive Link Power Management
SATA Aggressive Link Power Management allows SATA devices to enter a low power state during periods of inactivity to save power. It is only supported by AHCI mode.
Hard Disk S.M.A.R.T.
S.M.A.R.T stands for Self-Monitoring, Analysis, and Reporting Technology. It is a monitoring system for computer hard disk drives to detect and report on various indicators of reliability.
Page 40
4.3.4 Super IO Conguration
Serial Port 1
Enable or disable the Serial port 1.
J4105M J4005M
Serial Port Address
Select the address of the Serial port.
Serial Port 2
Enable or disable the Serial port 2.
Serial Port Address
Select the address of the Serial port.
Parallel Port
Enable or disable the Parallel port.
Change Settings
Select the address of the Parallel port.
Device Mode
Select the device mode according to your connected device.
English
35
Page 41
4.3.5 ACPI Conguration
Suspend to RAM
It is recommended to select auto for ACPI S3 power saving.
ACPI HPET Table
Enable the High Precision Event Timer for better performance and to pass WHQL tests.
English
36
PS/2 Keyboard Power On
Allow the system to be waked up by a PS/2 Keyboard.
PCIE Device Power On
Allow the system to be waked up by a PCIE device and enable wake on LAN.
Ring-In Power On
Allow the system to be waked up by onboard COM port modem Ring-In signals.
RTC Alarm Power On
Allow the system to be waked up by the real time clock alarm. Set it to By OS to let it be handled by your operating system.
Page 42
USB Keyboard/Remote Power On
Allow the system to be waked up by an USB keyboard or remote controller.
USB Mouse Power On
Allow the system to be waked up by an USB mouse.
J4105M J4005M
37
English
Page 43
4.3.6 USB Conguration
Legacy USB Support
Enable Legacy USB Support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.
English
38
Page 44

4.4 Tools

Instant Flash
Save UEFI les in your USB storage device and run Instant Flash to update your UEFI.
J4105M J4005M
Internet Flash
ASRock Internet Flash downloads and updates the latest UEFI rmware version from our servers for you. Please setup network conguration before using Internet Flash. *For BIOS backup and recovery purpose, it is recommended to plug in your USB
pen drive before using this function.
English
39
Page 45
Network Conguration
Use this to congure internet connection settings for Internet Flash.
Internet Setting
Enable or disable sound eects in the setup utility.
UEFI Download Server
Select a server to download the UEFI rmware.
English
40
Page 46

4.5 Hardware Health Event Monitoring Screen

is section allows you to monitor the status of the hardware on your system, including the parameters of the CPU temperature, motherboard temperature, fan speed and voltage.
J4105M J4005M
CPU Fan 1 Setting
is allows you to set CPU fan 1’s speed. Conguration options: [Full On] and [Automatic Mode]. e default value is [Full On].
Chassis Fan 1 Setting
is allows you to set chassis fan 1’s speed. Conguration options: [Full On], [Automatic Mode] and [Manual]. e default value is [Full On].
Case Open Feature
Enable or disable Case Open Feature to detect whether the chassis cover has been removed.
English
41
Page 47

4.6 Security Screen

In this section you may set or change the supervisor/user password for the system. You may also clear the user password.
Supervisor Password
Set or change the password for the administrator account. Only the administrator has authority to change the settings in the UEFI Setup Utility. Leave it blank and press enter to remove the password.
English
42
User Password
Set or change the password for the user account. Users are unable to change the settings in the UEFI Setup Utility. Leave it blank and press enter to remove the password.
Secure Boot
Enable to support Secure Boot.
Intel(R) Platform Trust Technology
Enable/disable Intel PTT in ME. Disable this option to use discrete TPM Module.
Page 48

4.7 Boot Screen

is section displays the available devices on your system for you to congure the boot settings and the boot priority.
Fast Boot
Fast Boot minimizes your computer's boot time. In fast mode you may not boot from an USB storage device. e VBIOS must support UEFI GOP if you are using an external graphics card. Please notice that Ultra Fast mode will boot so fast that the only way to enter this UEFI Setup Utility is to Clear CMOS or run the Restart to UEFI utility in Windows.
J4105M J4005M
Boot From Onboard LAN
Allow the system to be waked up by the onboard LAN.
Setup Prompt Timeout
Congure the number of seconds to wait for the setup hot key.
Bootup Num-Lock
Select whether Num Lock should be turned on or o when the system boots up.
Boot Beep
Select whether the Boot Beep should be turned on or o when the system boots up. Please note that a buzzer is needed.
English
43
Page 49
Full Screen Logo
Enable to display the boot logo or disable to show normal POST messages.
Boot Failure Guard Message
If the computer fails to boot for a number of times the system automatically restores the default settings.
English
44
Page 50

4.8 Exit Screen

Save Changes and Exit
When you select this option the following message, “Save conguration changes and exit setup?” will pop out. Select [OK] to save changes and exit the UEFI SETUP UTILITY.
J4105M J4005M
Discard Changes and Exit
When you select this option the following message, “Discard changes and exit setup?” will pop out. Select [OK] to exit the UEFI SETUP UTILITY without saving any changes.
Discard Changes
When you select this option the following message, “Discard changes?” will pop out. Select [OK] to discard all changes.
Load UEFI Defaults
Load UEFI default values for all options. e F9 key can be used for this operation.
Launch EFI Shell from lesystem device
Copy shellx64.e to the root directory to launch EFI Shell.
English
45
Page 51
Contact Information
If you need to contact ASRock or want to know more about ASRock, you’re welcome to visit ASRock’s website at http://www.asrock.com; or you may contact your dealer for further information. For technical questions, please submit a support request form at https://event.asrock.com/tsd.asp
ASRock Incorporation
2F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District,
Taipei City 112, Taiwan (R.O.C.)
ASRock EUROPE B.V.
Bijsterhuizen 11-11
6546 AR Nijmegen
e Netherlands
Phone: +31-24-345-44-33
Fax: +31-24-345-44-38
ASRock America, Inc.
13848 Magnolia Ave, Chino, CA91710
U.S.A.
Phone: +1-909-590-8308
Fax: +1-909-590-1026
Page 52
DECLARATION OF CONFORMITY
Per FCC Part 2 Section 2.1077(a)
Responsible Party Name: ASRock Incorporation
Address:
Phone/Fax No:
hereby declares that the product
Product Name : Motherboard
13848 Magnolia Ave, Chino, CA91710
+1-909-590-8308/+1-909-590-1026
Model Number :
Conforms to the following specications:
FCC Part 15, Subpart B, Unintentional Radiators
Supplementary Information:
J4105M / J4005M
is device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) is device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
James
Representative Person’s Name:
Signature :
Date :
May 12, 2017
Page 53
EU Declaration of Conformity
EMC —Directive 2014/30/EU (from April 20th, 2016)
For the following equipment:
Motherboard
(Product Name)
J4105M / J4005M / ASRock
(Model Designation / Trade Name)
ASRock Incorporation
(Manufacturer Name)
2F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District, Taipei City 112, Taiwan (R.O.C.)
(Manufacturer Address)
ڛ
☐ EN 55022:2010/AC:2011 Class B EN 55024:2010/A1:2015
ڛ EN 55032:2012+AC:2013 Class B ڛڛ EN 61000-3-3:2013 ڛ EN 61000-3-2:2014
LVD —Directive 2014/35/EU (from April 20th, 2016)
EN 60950-1 : 2011+ A2: 2013
ڛ RoHS — Directive 2011/65/EU ڛ CE marking
EN 60950-1 : 2006/A12: 2011
(EU conformity marking)
ASRock EUROPE B.V.
(Company Name)
Bijsterhuizen 1111 6546 AR Nijmegen e Netherlands
(Company Address)
Person responsible for making this declaration:
(Name, Surname)
A.V.P
(Position / Title)
December 29, 2017
(Date) P/N: 15G062068000AK V1.0
Loading...