Asrock H61 Pro BTC Quick Installation Guide

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or trans­lated in any language, in any form or by any means, except duplication of documentation
by the purchaser for backup purpose, without written consent of ASRock Inc.
Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for identica­tion or explanation and to the owners’ benet, without intent to infringe.

Disclaimer:

Specications and information contained in this guide are furnished for informational use

only and subject to change without notice, and should not be constructed as a commit­ment by ASRock. ASRock assumes no responsibility for any errors or omissions that may
appear in this guide.
With respect to the contents of this guide, ASRock does not provide warranty of any kind,
either expressed or implied, including but not limited to the implied warranties or condi-

tions of merchantability or tness for a particular purpose. In no event shall ASRock, its
directors, ofcers, employees, or agents be liable for any indirect, special, incidental, or
consequential damages (including damages for loss of prots, loss of business, loss of

data, interruption of business and the like), even if ASRock has been advised of the pos­sibility of such damages arising from any defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see
www.dtsc.ca.gov/hazardouswaste/perchlorate”

The terms HDMI™ and HDMI High-Denition Multimedia Interface, and the HDMI logo

are trademarks or registered trademarks of HDMI Licensing LLC in the United States and
other countries.

English

1

Motherboard Layout

ATXP WR1

Intel

H61

CMOS

Batt ery

32Mb
BIOS

DDR3 _A1 (64 bit, 2 40-pi n modu le)

DDR3 _B1 (64 bit, 2 40-pi n modu le)

Super

I/O

LAN
PHY

AUDIO

CODEC

1

HD_AUDIO 1

COM1

1

USB6_7

1

USB8_9

1

1

SPEAKER1

HDLED RESET

PLED PWRBTN

PANEL1

1

CLRCMOS1

1

SATA2_1

SATA2_3

SATA2_0

SATA2_2

PCI E2

PCI E1

PCI E3

PCI E4

PCI E5

PCI E6

RoHS

H6 1 P ro B TC

ATX12V1

IR1

1

PS2

Keybo ard

PS2

Mouse

VGA1

Top:
RJ-45

USB 2.0
T:U SB4
B: USB5

USB 2.0
T:US B0
B: USB1

Top:

LINE IN

Center:

FRONT

Bottom:

MIC IN

USB 2.0
T:US B2
B: USB3

HDMI 1

CPU_FAN1

CHA_FAN1

PWR_FAN1

1

2

3

4

5

6

7

8

9

10

11

12

14

13

15

16

17

18

1920

21

22

23

24

25

26

28

SLI/XFIRE _PWR1

X

Fast USB

X

Fast RAM

X

Fast LAN

SLI/XFIRE _PWR2

27

29

English

1 1155-Pin CPU Socket 15 SATA2 Connector (SATA2_1)
2 CPU Fan Connector (CPU_FAN1) 16 System Panel Header (PANEL1)
3 ATX 12V Power Connector (ATX12V1) 17 USB 2.0 Header (USB8_9)
4 2 x 240-pin DDR3 DIMM Slots 18 USB 2.0 Header (USB6_7)
(Dual Channel: DDR3_A1, DDR3_B1) 19 COM Port Header (COM1)
5 ATX Power Connector (ATXPWR1) 20 Front Panel Audio Header (HD_AUDIO1)
6 Chassis Fan Connector (CHA_FAN1) 21 PCI Express 2.0 x1 Slot (PCIE6)
7 32Mb SPI Flash 22 PCI Express 2.0 x1 Slot (PCIE5)
8 Intel H61 Chipset 23 PCI Express 2.0 x1 Slot (PCIE4)
9 Clear CMOS Jumper (CLRCMOS1) 24 PCI Express 2.0 x1 Slot (PCIE3)
10 Chassis Speaker Header (SPEAKER1) 25 PCI Express 3.0 x16 Slot (PCIE2)
11 SATA2 Connector (SATA2_2) 26 PCI Express 2.0 x1 Slot (PCIE1)
12 SATA2 Connector (SATA2_0) 27 SLI/XFire Power Connector (SLI/XFIRE_PWR2)
13 Infrared Module Header (IR1) 28 Power Fan Connector (PWR_FAN1)
14 SATA2 Connector (SATA2_3) 29 SLI/XFire Power Connector (SLI/XFIRE_PWR1)

2

ASRock H61 Pro BTC Motherboard

I/O Panel

1

2

3

4

5

11

1 PS/2 Mouse Port (Green) 7 USB 2.0 Ports (USB23)
* 2 LAN RJ-45 Port 8 USB 2.0 Ports (USB01)
3 Line In (Light Blue) 9 HDMI Port
** 4 Front Speaker (Lime) 10 D-Sub Port
5 Microphone (Pink) 11 PS/2 Keyboard Port (Purple)
6 USB 2.0 Ports (USB45)

* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED
indications.

Activity/Link LED SPEED LED

Status Description Status Description

10

LAN Port LED Indications

9

8

7

6

ACT/LINK
LED

SPEED
LED

Off No Link Off 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection

LAN Port

To enable Multi-Streaming function, you need to connect a front panel audio cable to the front

panel audio header. After restarting your computer, you will nd “VIA HD Audio Deck” tool on

your system. Please follow below instructions according to the OS you install.
For Windows® XP / XP 64-bit OS:

Please click “VIA HD Audio Deck” icon , and click “Speaker”. Then you are allowed to

select “2 Channel” or “4 Channel”. Click “Power” to save your change.

For Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS:

Please click “VIA HD Audio Deck” icon , and click “Advanced Options” on the left side

on the bottom. In “Advanced Options” screen, select “Independent Headphone”, and click
“OK” to save your change.

ASRock H61 Pro BTC Motherboard

English

3

1. Introduction

Thank you for purchasing ASRock H61 Pro BTC motherboard, a reliable mother-

board produced under ASRock’s consistently stringent quality control. It delivers

excellent performance with robust design conforming to ASRock’s commitment to
quality and endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found

in the user manual presented in the Support CD.

Because the motherboard specications and the BIOS software might be

updated, the content of this manual will be subject to change without no-

tice. In case any modications of this manual occur, the updated version
will be available on ASRock website without further notice. You may nd
the latest VGA cards and CPU support lists on ASRock website as well.

ASRock website http://www.asrock.com

If you require technical support related to this motherboard, please visit
our website for specic information about the model you are using.

www.asrock.com/support/index.asp

1.1 Package Contents

ASRock H61 Pro BTC Motherboard (ATX Form Factor)
ASRock H61 Pro BTC Quick Installation Guide
ASRock H61 Pro BTC Support CD

2 x Serial ATA (SATA) Data Cables (Optional)
1 x I/O Panel Shield

English

4

ASRock Reminds You...

To get better performance in Windows® 8 / 8 64-bit / 7 / 7 64-bit / Vista

VistaTM 64-bit, it is recommended to set the BIOS option in Storage Con­guration to AHCI mode. For the BIOS setup, please refer to the “User
Manual” in our support CD for details.

TM

ASRock H61 Pro BTC Motherboard

/

1.2 Specications

Platform - ATX Form Factor

- All Solid Capacitor design

CPU - Supports 3rd and 2nd generation Intel® CoreTM i7 / i5 / i3 /
Xeon® / Pentium® / Celeron® in LGA1155 package

- Supports Intel® Turbo Boost 2.0 Technology

- Supports K-Series unlocked CPUs
Chipset - Intel® H61

- Supports Intel® Rapid Start Technology and Smart Connect

Technology

Memory - Dual Channel DDR3 Memory Technology

- 2 x DDR3 DIMM Slots

- Supports DDR3 1600/1333/1066 non-ECC, un-buffered
memory (DDR3 1600 with Intel® Ivy Bridge CPU, DDR3
1333 with Intel® Sandy Bridge CPU)

- Max. capacity of system memory: 16GB (see CAUTION 1)

- Supports Intel® Extreme Memory Prole (XMP) 1.3 / 1.2 with
Intel® Ivy Bridge CPU
Expansion Slot - 1 x PCI Express 3.0 x16 Slot (PCIE2 @ x16 mode)

* PCIE 3.0 is only supported with Intel® Ivy Bridge CPU. With
Intel® Sandy Bridge CPU, it only supports PCIE 2.0.

- 5 x PCI Express 2.0 x1 Slots
Graphics * Intel® HD Graphics Built-in Visuals and the VGA outputs
can be supported only with processors which are GPU

integrated.

- Supports Intel® HD Graphics Built-in Visuals: Intel® Quick
Sync Video 2.0, Intel® InTruTM 3D, Intel® Clear Video HD
Technology, Intel® InsiderTM, Intel® HD Graphics 2500/4000
with Intel® Ivy Bridge CPU

- Supports Intel® HD Graphics Built-in Visuals: Intel® Quick
Sync Video, Intel® InTruTM 3D, Intel® Clear Video HD
Technology, Intel® HD Graphics 2000/3000, Intel® Advanced
Vector Extensions (AVX) with Intel® Sandy Bridge CPU

- Pixel Shader 5.0, DirectX 11 with Intel® Ivy Bridge CPU.
Pixel Shader 4.1, DirectX 10.1 with Intel® Sandy Bridge
CPU.

- Max. shared memory 1760MB with Intel® Ivy Bridge CPU.
Max. shared memory 1759MB with Intel® Sandy Bridge
CPU.

English

ASRock H61 Pro BTC Motherboard

5

English

- Dual VGA Output: support HDMI and D-Sub ports by

independent display controllers

- Supports HDMI Technology with max. resolution up to
1920x1200 @ 60Hz

- Supports D-Sub with max. resolution up to 2048x1536 @
75Hz

- Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and
HBR (High Bit Rate Audio) with HDMI Port (Compliant HDMI

monitor is required) (see CAUTION 2)

- Supports HDCP with HDMI Port

- Supports Full HD 1080p Blu-ray (BD) playback with HDMI

Port

Audio - 5.1 CH HD Audio (VIA® VT1705 Audio Codec)
LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Supports Wake-On-LAN

- Supports LAN Cable Detection

- Supports Energy Efcient Ethernet 802.3az

- Supports PXE

Rear Panel I/O - 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x D-Sub Port

- 1 x HDMI Port

- 6 x USB 2.0 Ports

- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

LED)

- HD Audio Jacks: Line in/Front Speaker/Microphone
Storage - 4 x SATA2 3.0 Gb/s Connectors, support NCQ, AHCI and
Hot Plug
Connector - 1 x IR Header

- 1 x COM Port Header

- 1 x CPU Fan Connector (4-pin)

- 1 x Chassis Fan Connector (4-pin)

- 1 x Power Fan Connector (4-pin)

- 1 x 24 pin ATX Power Connector

- 1 x 8 pin 12V Power Connector

- 2 x SLI/XFire Power Connectors

- 1 x Front Panel Audio Connector

- 2 x USB 2.0 Headers (Support 4 USB 2.0 ports)
BIOS Feature - 32Mb AMI UEFI Legal BIOS with GUI support

- Supports “Plug and Play”

6

ASRock H61 Pro BTC Motherboard

- ACPI 1.1 Compliant wake up events

- Supports jumperfree

- SMBIOS 2.3.1 support

- IGPU, DRAM, PCH, CPU PLL, VTT, VCCSA Voltage

multi-adjustment

Support CD - Drivers, Utilities, AntiVirus Software (Trial Version), Google
Chrome Browser and Toolbar

Hardware - CPU temperature sensing
Monitor - Chassis temperature sensing

- CPU/Chassis/Power Fan Tachometer

- CPU/Chassis Quiet Fan (Auto adjust chassis fan speed by
CPU temperature)

- CPU/Chassis Fan multi-speed control

- Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore

OS - Microsoft® Windows® 8 / 8 64-bit / 7 / 7 64-bit / Vista

TM

/

VistaTM 64-bit / XP / XP 64-bit compliant
Certications - FCC, CE, WHQL

- ErP/EuP ready (ErP/EuP ready power supply is required)

* For detailed product information, please visit our website: http://www.asrock.com

WARNING

Please realize that there is a certain risk involved with overclocking,
including adjusting the setting in the BIOS, applying Untied Overclocking

Technology, or using third-party overclocking tools. Overclocking may
affect your system’s stability, or even cause damage to the components

and devices of your system. It should be done at your own risk and

expense. We are not responsible for possible damage caused by
overclocking.

ASRock H61 Pro BTC Motherboard

English

7

CAUTION!

1. Due to the operating system limitation, the actual memory size
may be less than 4GB for the reservation for system usage

under Windows® 8 / 7 / VistaTM / XP. For Windows® OS with 64-

bit CPU, there is no such limitation. You can use ASRock XFast
RAM to utilize the memory that Windows® cannot use.

2. xvYCC and Deep Color are only supported under Windows® 8
64-bit / 8 / 7 64-bit / 7. Deep Color mode will be enabled only
if the display supports 12bpc in EDID. HBR is supported under

Windows® 8 64-bit / 8 / 7 64-bit / 7 / VistaTM 64-bit / VistaTM.

English

8

ASRock H61 Pro BTC Motherboard

1.3 Unique Features

ASRock Extreme Tuning Utility (AXTU)

ASRock Extreme Tuning Utility (AXTU) is an all-in-one tool to

ne-tune different system functions in a user-friendly interface,

which includes Hardware Monitor, Fan Control, Overclocking,
OC DNA, IES and XFast RAM. In Hardware Monitor, it shows
the major readings of your system. In Fan Control, it shows the
fan speed and temperature for you to adjust. In Overclocking,
you are allowed to overclock CPU frequency for optimal system
performance. In OC DNA, you can save your OC settings as
a prole and share it with your friends. Your friends then can
load the OC prole to their own system to get the same OC set­tings. In IES (Intelligent Energy Saver), the voltage regulator
can reduce the number of output phases to improve efciency
when the CPU cores are idle without sacricing computing per­formance. In XFast RAM, it fully utilizes the memory space that

cannot be used under Windows® OS 32-bit CPU.

ASRock Instant Boot

ASRock Instant Boot allows you to turn on your PC in just a few

seconds, provides a much more efcient way to save energy,

time, money, and improves system running speed for your sys-

tem. It leverages the S3 and S4 ACPI features which normally
enable the Sleep/Standby and Hibernation modes in Windows®
to shorten boot up time. By calling S3 and S4 at specic timing
during the shutdown and startup process, Instant Boot allows

you to enter your Windows® desktop in a few seconds.

ASRock Instant Flash

ASRock Instant Flash is a BIOS ash utility embedded in Flash

ROM. This convenient BIOS update tool allows you to update
system BIOS without entering operating systems rst like MS-

DOS or Windows®. With this utility, you can press the <F6> key

during the POST or the <F2> key to enter into the BIOS setup
menu to access ASRock Instant Flash. Just launch this tool and
save the new BIOS le to your USB ash drive, oppy disk or
hard drive, then you can update your BIOS only in a few clicks
without preparing an additional oppy diskette or other compli­cated ash utility. Please be noted that the USB ash drive or
hard drive must use FAT32/16/12 le system.

ASRock H61 Pro BTC Motherboard

English

9

ASRock APP Charger

If you desire a faster, less restricted way of charging your

Apple devices, such as iPhone/iPad/iPod Touch, ASRock has

prepared a wonderful solution for you - ASRock APP Charger.
Simply install the APP Charger driver, it makes your iPhone
charge much quickly from your computer and up to 40% faster
than before. ASRock APP Charger allows you to quickly charge

many Apple devices simultaneously and even supports continu-

ous charging when your PC enters into Standby mode (S1),
Suspend to RAM (S3), hibernation mode (S4) or power off (S5).
With APP Charger driver installed, you can easily enjoy the mar-

velous charging experience.

ASRock XFast USB

ASRock XFast USB can boost USB storage device perfor-

mance. The performance may depend on the properties of the
device.

ASRock XFast LAN

ASRock XFast LAN provides a faster internet access, which

includes the benefits listed below. LAN Application Prioritiza­tion: You can congure your application’s priority ideally and/or

add new programs. Lower Latency in Game: After setting online

game’s priority higher, it can lower the latency in games. Trafc
Shaping: You can watch Youtube HD videos and download si-

multaneously. Real-Time Analysis of Your Data: With the status

window, you can easily recognize which data streams you are

transferring currently.

English

10

ASRock XFast RAM

ASRock XFast RAM is a new function that is included into AS-

Rock Extreme Tuning Utility (AXTU). It fully utilizes the memory

space that cannot be used under Windows® OS 32-bit CPU.
ASRock XFast RAM shortens the loading time of previously
visited websites, making web surfing faster than ever. And it
also boosts the speed of Adobe Photoshop 5 times faster. An­other advantage of ASRock XFast RAM is that it reduces the

frequency of accessing your SSDs or HDDs in order to extend

their lifespan.

ASRock H61 Pro BTC Motherboard

ASRock Crashless BIOS

ASRock Crashless BIOS allows users to update their BIOS

without fear of failing. If power loss occurs during the BIOS up­date process, ASRock Crashless BIOS will automatically nish
the BIOS update procedure after regaining power. Please note
that BIOS les need to be placed in the root directory of your
USB disk. Only USB2.0 ports support this feature.

ASRock OMG (Online Management Guard)

Administrators are able to establish an internet curfew or restrict

internet access at specied times via OMG. You may schedule

the starting and ending hours of internet access granted to other

users. In order to prevent users from bypassing OMG, guest

accounts without permission to modify the system time are re­quired.

ASRock Internet Flash

ASRock Internet Flash searches for available UEFI firmware

updates from our servers. In other words, the system can auto­detect the latest UEFI from our servers and ash them without

entering Windows® OS. Please note that you must be running

on a DHCP congured computer in order to enable this function.

ASRock Dehumidier Function

Users may prevent motherboard damages due to dampness by

enabling “Dehumidier Function”. When enabling Dehumidier

Function, the computer will power on automatically to dehumidi-

fy the system after entering S4/S5 state.

ASRock Fast Boot

With ASRock’s exclusive Fast Boot technology, it takes less

than 1.5 seconds to logon to Windows® 8 from a cold boot. No

more waiting! The speedy boot will completely change your user
experience and behavior.

ASRock H61 Pro BTC Motherboard

English

11

ASRock Restart to UEFI

Windows® 8 brings the ultimate boot up experience. The light-

ning boot up speed makes it hard to access the UEFI setup. AS­Rock Restart to UEFI technology is designed for those requiring
frequent UEFI access. It allows users to easily enter the UEFI
automatically when turning on the PC next time. Just simply
enable this function; the PC will be assured to access the UEFI

directly in the very beginning.

ASRock Combo Cooler Option (C.C.O.)

Combo Cooler Option (C.C.O.) provides the exible option to

adopt three different CPU cooler types, Socket LGA 775, LGA
1155 and LGA 1156. Please be noticed that not all the 775 and
1156 CPU Fan can be used.

ASRock Good Night LED

ASRock Good Night LED technology can offer you a better en-

vironment by extinguishing the unessential LED. By enabling

Good Night LED in BIOS, the Power / HDD / LAN LED will be

switched off when system is on. Not only this, Good night LED

will automatically switch off Power and Keyboard LED when the
system enters into Standby / Hibernation mode as well.

English

12

ASRock H61 Pro BTC Motherboard

2. Installation

This is an ATX form factor motherboard. Before you install the motherboard, study

the conguration of your chassis to ensure that the motherboard ts into it.

motherboard. Failure to do so may cause physical injuries to you and
damages to motherboard components.

Make sure to unplug the power cord before installing or removing the

2.1 Screw Holes

Place screws into the holes indicated by circles to secure the motherboard to the
chassis.

Do not over-tighten the screws! Doing so may damage the motherboard.

2.2 Pre-installation Precautions

Take note of the following precautions before you install motherboard components
or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any component.

2. To avoid damaging the motherboard components due to static electricity,
NEVER place your motherboard directly on the carpet or the like. Also

remember to use a grounded wrist strap or touch a safety grounded object
before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded antistatic pad or

in the bag that comes with the component.

Before you install or remove any component, ensure that the power is

switched off or the power cord is detached from the power supply.
Failure to do so may cause severe damage to the motherboard, peripherals,
and/or components.

ASRock H61 Pro BTC Motherboard

English

13

2.3 CPU Installation

For the installation of Intel 1155-Pin CPU,

please follow the steps below.

Before you insert the 1155-Pin CPU into the socket, please check if the
CPU surface is unclean or if there is any bent pin on the socket. Do not
force to insert the CPU into the socket if above situation is found. Other­wise, the CPU will be seriously damaged.

Step 1. Open the socket:

Step 1-1. Disengaging the lever by depressing

down and out on the hook to clear
retention tab.

Step 1-2. Rotate the load lever to fully open po-

sition at approximately 135 degrees.

Step 1-3. Rotate the load plate to fully open po-

sition at approximately 100 degrees.

1155-Pin Socket Overview

English

14

Step 2. Remove PnP Cap:

Step 2-1. Attach your index nger to the upper

edge of the PnP Cap.

Step 2-2. Use your thumb to remove PnP Cap

(Pick and Place Cap) from the CPU

socket by lifting the cap tab.

1. It is recommended to use the cap tab to handle and avoid kicking

off the PnP cap.

2. This cap must be placed if returning the motherboard for after

service.

ASRock H61 Pro BTC Motherboard

B

A

Step 3. Insert the 1155-Pin CPU:

Step 3-1. Hold the CPU by the edge where is

marked with black line.

Step 3-2. Orient the CPU with IHS (Integrated

Heat Sink) up. Locate Pin1 and the

two orientation key notches.

orientation key notch

Pin1

orientation key notch

1155-Pin CPU

For proper inserting, please ensure to match the two orientation key

notches of the CPU with the two alignment keys of the socket.

Step 3-3. Car efully pla ce the CPU into the

socket by using a purely vertical mo­tion.

Step 3-4. Verify that the CPU is within the sock-

et and properly mated to the orient
keys.

black line

alignment key

Pin1

alignment key

1155-Pin Socket

Step 4. Close the socket:

Step 4-1. Rotate the load plate onto the IHS.
Step 4-2. While pressing down lightly on load

plate, engage the load lever.

Step 4-3. Secure load lever with load plate tab

under retention tab of load lever.

Please be noticed that this motherboard supports Combo Cooler
Option (C.C.O.), which provides the exible option to adopt three dif­ferent CPU cooler types, Socket LGA 775, LGA 1155 and LGA 1156.

The white throughholes are for Socket LGA

1155/1156 CPU fan.

ASRock H61 Pro BTC Motherboard

English

15

2.4 Installation of CPU Fan and Heatsink

This motherboard is equipped with 1155-Pin socket that supports Intel 1155-Pin
CPU. Please adopt the type of heatsink and cooling fan compliant with Intel 1155­Pin CPU to dissipate heat. Before you installed the heatsink, you need to spray
thermal interface material between the CPU and the heatsink to improve heat dis­sipation. Ensure that the CPU and the heatsink are securely fastened and in good
contact with each other. Then connect the CPU fan to the CPU_FAN connector
(CPU_FAN1, see page 2, No. 2).

For proper installation, please kindly refer to the instruction manuals of your
CPU fan and heatsink.

Below is an example to illustrate the installation of the heatsink for 1155-Pin CPU.

Step 1. Apply thermal interface material onto center of

IHS on the socket surface.

Step 2. Place the heatsink onto the socket. Ensure

fan cables are oriented on side closest to the

CPU fan connector on the motherboard (CPU_
FAN1, see page 2, No. 2).

Step 3. Align fasteners with the motherboard through-

holes.

Step 4. Rotate the fastener clockwise, then press

down on fastener caps with thumb to install
and lock. Repeat with remaining fasteners.

English

16

If you press down the fasteners without rotating them clockwise, the

heatsink cannot be secured on the motherboard.

Step 5. Connect fan header with the CPU fan connector on the motherboard.

Step 6. Secure excess cable with tie-wrap to ensure cable does not interfere with
fan operation or contact other components.

ASRock H61 Pro BTC Motherboard

2.5 Installation of Memory Modules (DIMM)

This motherboard provides two 240-pin DDR3 (Double Data Rate 3) DIMM slots,
and supports Dual Channel Memory Technology. For dual channel configuration,
you always need to install two identical (the same brand, speed, size and chip­type) memory modules in the DDR3 DIMM slots to activate Dual Channel Memory

Technology. Otherwise, it will operate at single channel mode.

1. It is not allowed to install a DDR or DDR2 memory module into

DDR3 slot;otherwise, this motherboard and DIMM may be

damaged.

2. If you install only one memory module or two non-identical
memory modules, it is unable to activate the Dual Channel

Memory Technology.

3. Some DDR3 1GB double-sided DIMMs with 16 chips may not
work on this motherboard. It is not recommended to install them

on this motherboard.

Installing a DIMM

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.
Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the

break on the slot.

The DIMM only ts in one correct orientation. It will cause permanent
damage to the motherboard and the DIMM if you force the DIMM into

the slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends
fully snap back in place and the DIMM is properly seated.

ASRock H61 Pro BTC Motherboard

English

17

2.6 Expansion Slots (PCI Express Slots)

There are 6 PCI Express slots on this motherboard.

PCIE slots:

PCIE1 / PCIE3 / PCIE4 / PCIE5 / PCIE6 (PCIE 2.0 x1 slot) is used for

PCI Express cards with x1 lane width cards.

PCIE2 (PCIE 3.0 x16 slot) is used for PCI Express x16 lane width

graphics cards.

Only PCIE2 slot supports Gen 3 speed. To run the PCI Express in Gen

3 speed, please install an Ivy Bridge CPU. If you install a Sandy Bridge
CPU, the PCI Express will run only at PCI Express Gen 2 speed.

English

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the
documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the system unit cover (if your motherboard is already installed

in a chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep the

screws for later use.

Step 4. Align the card connector with the slot and press rmly until the card is

completely seated on the slot.

Step 5. Fasten the card to the chassis with screws.

Step 6. Replace the system cover.

18

ASRock H61 Pro BTC Motherboard

2.7 Jumpers Setup

The illustratio n shows how jump ers are
setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap
is placed on pins, the jumper is “Open”. The

illustration shows a 3-pin jumper whose

pin1 and pin2 are “Short” when jumper cap
is placed on these 2 pins.

Jumper Setting Description

Clear CMOS Jumper

(CLRCMOS1)
(see p.2, No. 9)

Note: CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the

system parameters to default setup, please turn off the computer and unplug

the power cord from the power supply. After waiting for 15 seconds, use a
jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However,
please do not clear the CMOS right after you update the BIOS. If you need
to clear the CMOS when you just nish updating the BIOS, you must boot
up the system rst, and then shut it down before you do the clear-CMOS ac­tion. Please be noted that the password, date, time, user default prole, 1394
GUID and MAC address will be cleared only if the CMOS battery is removed.

Clear CMOSDefault

ASRock H61 Pro BTC Motherboard

English

19

2.8 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!

Serial ATAII Connectors These four Serial ATAII

(SATA2_0: see p.2, No. 12)

(SATA2_1: see p.2, No. 15)

(SATA2_2: see p.2, No. 11)

(SATA2_3: see p.2, No. 14)

SATA2_0

(SATAII) connectors support

SATA data cables for internal

storage devices. The current

SATA2_1

SATAII interface allows up to

SATA2_2

SATA2_3

3.0 Gb/s data transfer rate.

Serial ATA (SATA) Either end of the SATA data

Data Cable cable can be connected to the

(Optional)

SATA / SATAII hard disk or the

SATAII connector on this

motherboard.

USB 2.0 Headers Besides six default USB 2.0

(9-pin USB6_7)

(see p.2 No. 18)

ports on the I/O panel, there

are two USB 2.0 headers on

this motherboard. Each

USB 2.0 header can support
two USB 2.0 ports.

(9-pin USB8_9)
(see p.2 No. 17)

1

USB _PWR

P-9

P-8

USB _PWR

P+9

P+8

GND

GND

DUM MY

English

20

Infrared Module Header This header supports an

(5-pin IR1)

optional wireless transmitting

(see p.2 No. 13)

and receiving infrared module.

ASRock H61 Pro BTC Motherboard

Front Panel Audio Header This is an interface for front

(9-pin HD_AUDIO1)

(see p.2 No. 20)

panel audio cable that allows

convenient connection and

control of audio devices.

1

GND

PRE SENC E#

MIC 2_R

MIC 2_L

MIC _RET

J_S ENSE

OUT 2_R

OUT _RET

OUT 2_L

1. High Denition Audio supports Jack Sensing, but the panel wire on
the chassis must support HDA to function correctly. Please follow the

instruction in our manual and chassis manual to install your system.

2. If you use AC’97 audio panel, please install it to the front panel audio

header as below:

A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for HD audio panel only. You don’t

need to connect them for AC’97 audio panel.

System Panel Header This header accommodates

(9-pin PANEL1)

(see p.2 No. 16)

several system front panel

functions.

Connect the power switch, reset switch and system status indicator on the

chassis to this header according to the pin assignments below. Note the
positive and negative pins before connecting the cables.

PWRBTN (Power Switch):

Connect to the power switch on the chassis front panel. You may congure

the way to turn off your system using the power switch.

RESET (Reset Switch):

Connect to the reset switch on the chassis front panel. Press the reset

switch to restart the computer if the computer freezes and fails to perform a

normal restart.

PLED (System Power LED):

Connect to the power status indicator on the chassis front panel. The LED

is on when the system is operating. The LED keeps blinking when the sys-

tem is in S1 sleep state. The LED is off when the system is in S3/S4 sleep
state or powered off (S5).

HDLED (Hard Drive Activity LED):

Connect to the hard drive activity LED on the chassis front panel. The LED

is on when the hard drive is reading or writing data.

ASRock H61 Pro BTC Motherboard

English

21

The front panel design may differ by chassis. A front panel module mainly

consists of power switch, reset switch, power LED, hard drive activity LED,
speaker and etc. When connecting your chassis front panel module to this
header, make sure the wire assignments and the pin assign-ments are
matched correctly.

Chassis Speaker Header Please connect the chassis

(4-pin SPEAKER 1)

(see p.2 No. 10)

speaker to this header.

Chassis and Power Fan Connectors Please connect the fan cables

(4-pin CHA_FAN1)

(see p.2 No. 6)

to the fan connectors and

match the black wire to the

ground pin.

(4-pin PWR_FAN1)
(see p.2 No. 28)

English

CPU Fan Connectors Please connect the CPU fan

(4-pin CPU_FAN1)

(see p.2 No. 2)

cable to the connector and

match the black wire to the

ground pin.

FAN_ SPEE D_CO NTRO L

CPU _FAN_ SPEE D

+12 V

GND

1 2 3 4

Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin

CPU fan still can work successfully even without the fan speed control function.
If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this

motherboard, please connect it to Pin 1-3.

Pin 1-3 Connected

3-Pin Fan Installation

ATX Power Connector Please connect an ATX power

(24-pin ATXPWR1)

(see p.2 No. 5)

supply to this connector.

Though this motherboard provides 24-pin ATX power connector,

12 124

13

12

it can still work if you adopt a traditional 20-pin ATX power supply.
To use the 20-pin ATX power supply, please plug your

power supply along with Pin 1 and Pin 13.

20-Pin ATX Power Supply Installation

1

24

13

22

ASRock H61 Pro BTC Motherboard

ATX 12V Power Connector Please connect an ATX 12V

(8-pin ATX12V1)

(see p.2 No. 3)

power supply to this connector.

8 5

4 1

Though this motherboard provides 8-pin ATX 12V power connector, it can still work
if you adopt a traditional 4-pin ATX 12V power supply. To use the 4-pin ATX power
supply, please plug your power supply along with Pin 1 and Pin 5.

8 5

4-Pin ATX 12V Power Supply Installation

4 1

Serial Port Header This COM1 header supports a

(9-pin COM1)

(see p.2 No. 19)

serial port module.

SLI/XFire Power Connectors Please connect these

(4-pin SLI/XFIRE_PWR1)

(see p.2 No. 29)

connectors to the power supply

when three graphics cards are

installed on this motherboard.

(4-pin SLI/XFIRE_PWR2)
(see p.2 No. 27)

ASRock H61 Pro BTC Motherboard

English

23

3. BIOS Information

The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up
the computer, please press <F2> or <Del> during the Power-On-Self-Test (POST)
to enter BIOS Setup utility; otherwise, POST continues with its test routines. If you
wish to enter BIOS Setup after POST, please restart the system by pressing <Ctl>
+ <Alt> + <Delete>, or pressing the reset button on the system chassis. The BIOS
Setup program is designed to be user-friendly. It is a menu-driven program, which

allows you to scroll through its various sub-menus and to select among the prede-

termined choices. For the detailed information about BIOS Setup, please refer to the
User Manual (PDF le) contained in the Support CD.

4. Software Support CD information

®

This motherboard supports various Microsoft

64-bit / 7 / 7 64-bit / VistaTM / Vista

came with the motherboard contains necessary drivers and useful utilities that will

enhance motherboard features. To begin using the Support CD, insert the CD into
your CD-ROM drive. It will display the Main Menu automatically if “AUTORUN” is
enabled in your computer. If the Main Menu does not appear automatically, locate
and double-click on the le “ASSETUP.EXE” from the BIN folder in the Support CD

to display the menus.

TM

64-bit / XP / XP 64-bit. The Support CD that

Windows® operating systems: 8 / 8

English

24

ASRock H61 Pro BTC Motherboard

1. Einführung

Wir danken Ihnen für den Kauf des ASRock H61 Pro BTC Motherboard, ein zuver­lässiges Produkt, welches unter den ständigen, strengen Qualitätskontrollen von

ASRock gefertigt wurde. Es bietet Ihnen exzellente Leistung und robustes Design,
gemäß der Verpflichtung von ASRock zu Qualität und Halbarkeit. Diese Schnel­linstallationsanleitung führt in das Motherboard und die schrittweise Installation
ein. Details über das Motherboard nden Sie in der Bedienungsanleitung auf der
Support-CD.

Da sich Motherboard-Spezikationen und BIOS-Software verändern
können, kann der Inhalt dieses Handbuches ebenfalls jederzeit geändert
werden. Für den Fall, dass sich Änderungen an diesem Handbuch
ergeben, wird eine neue Version auf der ASRock-Website, ohne weitere
Ankündigung, verfügbar sein. Die neuesten Grakkarten und unterstützten
CPUs sind auch auf der ASRock-Website aufgelistet.

ASRock-Website: http://www.asrock.com
Wenn Sie technische Unterstützung zu Ihrem Motherboard oder spezische

Informationen zu Ihrem Modell benötigen, besuchen Sie bitte unsere

Webseite:
www.asrock.com/support/index.asp

1.1 Kartoninhalt

ASRock H61 Pro BTC Motherboard (ATX-Formfaktor)
ASRock H61 Pro BTC Schnellinstallationsanleitung
ASRock H61 Pro BTC Support-CD
Zwei Serial ATA (SATA) -Datenkabel (optional)

Ein I/O Shield

ASRock erinnert...

Zur besseren Leistung unter Windows® 8 / 8 64 Bit / 7 / 7 64 Bit / Vista

VistaTM 64 Bit empfehlen wir, die Speicherkonguration im BIOS auf den
AHCI-Modus einzustellen. Hinweise zu den BIOS-Einstellungen nden
Sie in der Bedienungsanleitung auf der mitgelieferten CD.

TM

ASRock H61 Pro BTC Motherboard

/

Deutsch

25

Deutsch

1.2 Spezikationen

Plattform - ATX-Formfaktor

- Alle Feste Kondensatordesign
CPU - Unterstützt Intel® CoreTM i7- / i5- / i3- / Xeon®- / Pentium®- /
Celeron®-Prozessoren der 3ten und 2ten Generation im
LGA1155-Package

- Unterstützt Intel® Turbo Boost 2.0-Technologie

- Unterstützt freigegebene CPU der K-Serie
Chipsatz - Intel® H61

- Unterstützt Intel® Rapid Start Technology und Smart
Connect Technology
Speicher - Unterstützung von Dual-Kanal-Speichertechnologie

- 2 x Steckplätze für DDR3

- Unterstützt DDR3 1600/1333/1066 non-ECC, ungepufferter
Speicher (DDR3 1600 mit Intel® Ivy Bridge-Prozessor,
DDR3 1333 mit Intel® Sandy Bridge-Prozessor)

- Max. Kapazität des Systemspeichers: 16GB

- Unterstützt Intel® Extreme Memory Prole (XMP)1.3/1.2 mit
Intel® Ivy Bridge-Prozessor
Erweiterungs- - 1 x PCI Express 3.0 x16-Steckplatz (PCIE2 für x16-Modus)
steckplätze * PCIE 3.0 wird nur mit Intel® Ivy Bridge-Prozessor
unterstützt. Mit Intel® Sandy Bridge-Prozessor wird nur
PCIE 2.0 unterstützt.

- 5 x PCI Express 2.0 x1-Steckplätze
Onboard-VGA * Integrierte Intel® HD-Grakdarstellungen und die VGA­ Ausgänge können nur durch GPU-integrierte Prozessoren
unterstützt werden.

- Unterstützt hochauösende integrierte Intel®-Graklösungen:
Intel® Quick-Sync-Video 2.0, Intel® InTruTM 3D, Intel® Clear­ Video-Technik (HD), Intel® InsiderTM, Intel® HD Graphics
2500/4000 mit Intel® Ivy Bridge-Prozessor

- Unterstützt hochauösende integrierte Intel®-Graklösungen:
Intel® Quick-Sync-Video, Intel® InTruTM 3D, Intel® Clear­ Video-Technik (HD), Intel® HD Graphics 2000/3000, Intel®
Advanced Vector Extensions (AVX) mit Intel® Sandy Bridge­ Prozessor

- Pixel Shader 5.0, DirectX 11 mit Intel® Ivy Bridge-Prozessor,
Pixel Shader 4.1, DirectX 10.1 mit Intel® Sandy Bridge­ Prozessor

26

ASRock H61 Pro BTC Motherboard

- Maximal gemeinsam genutzter Speicher 1760MB mit Intel®
Ivy Bridge-Prozessor. Maximal gemeinsam genutzter
Speicher 1759MB mit Intel® Sandy Bridge-Prozessor.

- Doppel-VGA Ausgabe: unterstützt HDMI und D-Sub Ports
durch unabhängige Bildschirmanzeige Kontrolleure

- Unterstützt HDMI mit einer maximalen Auösung von
1920 x 1200 bei 60 Hz

- Unterstützt D-Sub mit einer maximalen Auösung von
2048 x 1536 bei 75 Hz

- Unterstützt Auto Lip Sync, Deep Color (12bpc), xvYCC und
HBR (High Bit Rate-Audio) mit HDMI (kompatibler HDMI-

Bildschirm erforderlich)

- Unterstützt HDCP-Funktion mit HDMI-Port

- Unterstutzt 1080p Blu-ray (BD) / HD-DVD-Wiedergabe mit
HDMI-Port

Audio - 5.1 CH HD Audio (VIA® VT1705 Audio Codec)
LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Unterstützt Wake-On-LAN

- Unterstützt LAN-Kabelerkennung

- Unterstützt energieefzientes Ethernet 802.3az

- Unterstützt PXE

E/A-Anschlüsse - 1 x PS/2-Mausanschluss
an der - 1 x PS/2-Tastaturanschluss
Rückseite - 1 x D-Sub port

- 1 x HDMI port

- 6 x Standard-USB 2.0-Anschlüsse

- 1 x RJ-45 LAN Port mit LED (ACT/LINK LED und SPEED

LED)

- HD Audiobuchse: Audioeingang / Lautsprecher vorne /

Mikrofon

Speichergerät - 4 x SATA2 3,0 GB/s-Anschlüsse, unterstützen NCQ-, AHCI-
und „Hot Plug“ (Hot-Plugging)- Funktionen
Anschlüsse - 1 x Infrarot-Modul-Header

- 1 x COM-Anschluss-Header

- 1 x CPUlüfter-Anschluss (4-pin)

- 1 x Gehäuselüfter-Anschluss (4-pin)

- 1 x Stromlüfter-Anschluss (4-pin)

- 1 x 24-pin ATX-Netz-Header

- 1 x 8-pin anschluss für 12V-ATX-Netzteil

- 2 x SLI/XFire-Netz-Header

Deutsch

ASRock H61 Pro BTC Motherboard

27

- 1 x Anschluss für Audio auf der Gehäusevorderseite

- 2 x USB 2.0-Anschlüsse (Unterstützung 4 zusätzlicher
USB 2.0-Anschlüsse)
BIOS - 32Mb AMIs Legal BIOS UEFI mit GUI-Unterstützung

- Unterstützung für “Plug and Play”

- ACPI 1.1-Weckfunktionen

- JumperFree-Übertaktungstechnologie

- SMBIOS 2.3.1

- IGPU, DRAM, PCH, CPU PLL, VTT, VCCSA

Stromspannung Multianpassung
CD d’assistance - Pilotes, utilitaires, logiciel anti-virus (version d’évaluation),

Google Chrome Browser und Toolbar

Hardware Monitor - Überwachung der CPU-Temperatur

- Motherboardtemperaturerkennung

- Drehzahlmessung für CPU/Gehäuse/Stromlüfter

- Geräuscharmer CPU-/Gehäuselüfter (ermöglicht die au
tomatische Anpassung der Gehäuselüftergeschwindigkeit
durch CPU- Temperatur)

- Mehrstuge Geschwindigkeitsteuerung für CPU-/
Gehäuselüfter

- Spannungsüberwachung: +12V, +5V, +3.3V, Vcore

®

Betriebssysteme - Unterstützt Microsoft
VistaTM / Vista

TM

Windows® 8 / 8 64-Bit / 7 / 7 64-Bit /

64-Bit / XP / XP 64-Bit

Zertizierungen - FCC, CE, WHQL

- Gemäß Ökodesign-Richtlinie (ErP/EuP) (Stromversorgung
gemäß Ökodesign-Richtlinie (ErP/EuP) erforderlich)

* Für die ausführliche Produktinformation, besuchen Sie bitte unsere Website:

http://www.asrock.com

Deutsch

28

ASRock H61 Pro BTC Motherboard

1.3 Einstellung der Jumper

Die Abbildung verdeutlicht, wie Jumper

gesetzt werden. Werden Pins durch

Jumperkappen verdeckt, ist der Jumper

“Gebrückt”. Werden keine Pins durch

Jumperkappen verdeckt, ist der Jumper

“Offen”. Die Abbildung zeigt einen 3-Pin
Jumper dessen Pin1 und Pin2 “Ge­brückt” sind, bzw. es bendet sich eine
Jumper-Kappe auf diesen beiden Pins.

Jumper Einstellun Beschreibung

CMOS löschen

(CLRCMOS1, 3-Pin jumper)
(siehe S.2, No. 9)

Hinweis:

CLRCMOS1 ermöglicht Ihnen die Löschung der Daten im CMOS. Zum
Löschen und Zurücksetzen der Systemparameter auf die Standardeinrichtung
schalten Sie den Computer bitte aus und trennen das Netzkabel von der
Stromversorgung. Warten Sie 15 Sekunden, schließen Sie dann Pin2 und
Pin3 am CLRCMOS1 über einen Jumper fünf Sekunden lang kurz. Sie
sollten das CMOS allerdings nicht direkt nach der BIOS-Aktualisierung
löschen. Wenn Sie das CMOS nach Abschluss der BIOS-Aktualisierung
löschen müssen, fahren Sie zuerst das System hoch. Fahren Sie es dann
vor der CMOS-Löschung herunter. Bitte beachten Sie, dass Kennwort,
Datum, Uhrzeit, benutzerdeniertes Prol, 1394 GUID und MAC-Adresse
nur gelöscht werden, wenn die CMOS-Batterie entfernt wird.

Default­Einstellung

CMOS

löschen

ASRock H61 Pro BTC Motherboard

Deutsch

29

1.4 Integrierte Header und Anschlüsse

Seriell-ATAII-Anschlüsse Diese vier Serial ATAII-

(SATA2_0: siehe S.2 - No. 12)

(SATA2_1: siehe S.2 - No. 15)

(SATA2_2: siehe S.2 - No. 11)

(SATA2_3: siehe S.2 - No. 14)

aktuelle SATAII-Schnittstelle

ermöglicht eine

Datenübertragungsrate bis

3,0 Gb/s.

Serial ATA- (SATA-) SJedes Ende des SATA
Datenkabel Datenkabels kann an die SATA

(Option)

oder das SATAII
Verbindungsstück auf
dieser Hauptplatine

angeschlossen werden.

Integrierte Header und Anschlüsse sind KEINE Jumper. Setzen Sie KE­INE Jumperkappen auf diese Header und Anschlüsse. Wenn Sie Jump­erkappen auf Header und Anschlüsse setzen, wird das Motherboard

unreparierbar beschädigt!

SATA2_0

(SATAII-) Verbínder

SATA2_2

unterstützten SATA-Datenkabel

für interne

SATA2_1

Massenspeichergeräte. Die

SATA2_3

/ SATAII Festplatte

Deutsch

30

USB 2.0-Header Zusätzlich zu den sechs

(9-pol. USB6_7)

(siehe S.2 - No. 18)

üblichen USB 2.0-Ports an den

I/O-Anschlüssen benden sich

zwei USB 2.0-

Anschlussleisten am

Motherboard. Pro USB 2.0-

(9-pol. USB8_9)

(siehe S.2 - No. 17)

Anschlussleiste werden zwei

USB 2.0-Ports unterstützt.

1

USB _PWR

P-9

P-8

USB _PWR

P+9

P+8

GND

GND

DUM MY

Infrarot-Modul-Header Dieser Header unterstützt ein

(5-pin IR1)

optionales, drahtloses Sende-

(siehe S.2 - No. 13)

und Empfangs-Infrarotmodul.

ASRock H61 Pro BTC Motherboard

Anschluss für Audio auf Dieses Interface zu einem
der Gehäusevorderseite Audio-Panel auf der Vorder

(9-Pin HD_AUDIO1)

(siehe S.2 - No. 20)

seite Ihres Gehäuses,

ermöglicht Ihnen eine bequeme

Anschlussmöglichkeit und

Kontrolle über Audio-Geräte.

1

GND

PRE SENC E#

MIC 2_R

MIC 2_L

MIC _RET

J_S ENSE

OUT 2_R

OUT _RET

OUT 2_L

1. High Denition Audio unterstützt Jack Sensing (automatische Erkennung

falsch angeschlossener Geräte), wobei jedoch die Bildschirmverdrahtung

am Gehäuse HDA unterstützen muss, um richtig zu funktionieren.
Beachten Sie bei der Installation im System die Anweisungen in unserem
Handbuch und im Gehäusehandbuch.

2. Wenn Sie die AC’97-Audioleiste verwenden, installieren Sie diese wie

nachstehend beschrieben an der Front-Audioanschlussleiste:

A. Schließen Sie Mic_IN (MIC) an MIC2_L an.
B. Schließen Sie Audio_R (RIN) an OUT2_R und Audio_L (LIN) an OUT2_L an.
C. Schließen Sie Ground (GND) an Ground (GND) an.

D. MIC_RET und OUT_RET sind nur für den HD-Audioanschluss gedacht. Diese

Anschlüsse müssen nicht an die AC’97-Audioleiste angeschlossen werden.

System Panel-Header Dieser Header unterstützt

(9-pin PANEL1)

(siehe S.2 - No. 16)

mehrere Funktion der

Systemvorderseite.

Schließen Sie die Ein-/Austaste, die Reset-Taste und die

Systemstatusanzeige am Gehäuse an diesen Header an; befolgen Sie
dabei die nachstehenden Hinweise zur Pinbelegung. Beachten Sie die
positiven und negativen Pins, bevor Sie die Kabel anschließen.

PWRBTN (Ein-/Ausschalter):

Zum Anschließen des Ein-/Ausschalters an der Frontblende des Gehäu

ses. Sie können kongurieren, wie das System mit Hilfe des

Ein-/Ausschalters ausgeschaltet werden können soll.

RESET (Reset-Taste):

Zum Anschließen der Reset-Taste an der Frontblende des Gehäuses.

Mit der Reset-Taste können Sie den Computer im Falle eines Absturzes

neu starten.

PLED (Systembetriebs-LED):

Zum Anschließen der Betriebsstatusanzeige an der Frontblende des

Gehäuses. Die LED leuchtet, wenn das System in Betrieb ist. Die LED

blinkt, wenn sich das System im Ruhezustand S1 bendet. Die LED
schaltet sich aus, wenn sich das System in den Modi S3/S4 bendet
oder ausgeschaltet ist (S5).

ASRock H61 Pro BTC Motherboard

Deutsch

31

HDLED (Festplattenaktivitäts-LED):

Zum Anschließen der Festplattenaktivitäts-LED an der Frontblende des
Gehäuses. Die LED leuchtet, wenn die Festplatte Daten liest oder
schreibt.

Das Design der Frontblende kann je nach Gehäuse variiere. Ein
Frontblendenmodul besteht hauptsächlich aus einer Ein-/Austaste, einer
Reset-Taste, einer Betriebs-LED, einer Festplattenaktivitäts-LED,
Lautsprechern, etc. Stellen Sie beim Anschließen des

Frontblendenmoduls Ihres Gehäuses an diesem Header sicher, dass die
Kabel- und Pinbelegung korrekt übereinstimmen.

Gehäuselautsprecher-Header Schließen Sie den

(4-pin SPEAKER1)

(siehe S.2 - No. 10)

Gehäuselautsprecher an

diesen Header an.

Deutsch

Gehäuse- und Stromlüfteranschlüsse

(4-pin CHA_FAN1)

(siehe S.2 - No. 6)

Verbinden Sie die Lüfterkabel mit
den Lüfteranschlüssen, wobei
der schwarze Draht an den
Schutzleiterstift angeschlossen

(4-pin PWR_FAN1)

(siehe S.2 - No. 28)

CPU-Lüfteranschluss Verbinden Sie das CPU -

(4-pin CPU_FAN1)

(siehe S.2 - No. 2)

Lüfterkabel mit diesem

Anschluss und passen Sie den

FAN_ SPEE D_CO NTRO L

CPU _FAN_ SPEE D

+12 V

GND

wird.

schwarzen Draht dem

Erdungsstift an.

Obwohl dieses Motherboard einen vierpoligen CPU-Lüfteranschluss
(Quiet Fan) bietet, können auch CPU-Lüfter mit dreipoligem Anschluss

angeschlossen werden; auch ohne Geschwindigkeitsregulierung. Wenn

Sie einen dreipoligen CPU-Lüfter an den CPU-Lüferanschluss dieses

Motherboards anschließen möchten, verbinden Sie ihn bitte mit den
Pins 1 – 3.

ATX-Netz-Header Verbinden Sie die ATX-

(24-pin ATXPWR1)

(siehe S.2 - No. 5)

Stromversorgung mit diesem

Header.

1 2 3 4

Pins 1–3 anschließen

Lüfter mit dreipoligem Anschluss installieren

12 124

32

13

ASRock H61 Pro BTC Motherboard

Obwohl dieses Motherboard einen 24-pol. ATX-

Stromanschluss bietet, kann es auch mit einem

modizierten traditionellen 20-pol. ATX-Netzteil
verwendet werden. Um ein 20-pol. ATX-Netzteil zu

verwenden, stecken Sie den Stecker mit Pin 1 und
Pin 13 ein.

Installation eines 20-pol. ATX-Netzteils

12

1

24

13

ATX 12V Anschluss Bitte schließen Sie an diesen

(8-pin ATX12V1)

(siehe S.2 - No. 3)

Anschluss die ATX 12V

Stromversorgung an.

8 5

4 1

Obwohl diese Hauptplatine 8-Pin ATX 12V Stromanschluss zur
Verfügung stellt, kann sie noch arbeiten, wenn Sie einen
traditionellen 4-Pin ATX 12V Energieversorgung adoptieren. Um die
4-Pin ATX Energieversorgung zu verwenden, stecken Sie bitte Ihre
Energieversorgung zusammen mit dem Pin 1 und Pin 5 ein.

8 5

Installation der 4-Pin ATX 12V Energieversorgung

4 1

COM-Anschluss-Header Dieser COM-Anschluss-

(9-pin COM1)

(siehe S.2 - No. 19)

Header wird verwendet, um

ein COM-Anschlussmodul zu

unterstützen.

SLI/XFire-Stromanschluss

(4-pin SLI/XFIRE_PWR1)

(siehe S.2 - No. 29)

Bitte verbinden Sie diese

Anschluss mit einem Netzteils,
wenn drei Grakkarten an

diesem Motherboard installiert

(4-pin SLI/XFIRE_PWR2)

(siehe S.2 - No. 27)

sind.

ASRock H61 Pro BTC Motherboard

Deutsch

33

2. BIOS-Information

Das Flash Memory dieses Motherboards speichert das Setup-Utility. Drücken Sie
<F2> oder <Del> während des POST (Power-On-Self-Test) um ins Setup zu gelan-

gen, ansonsten werden die Testroutinen weiter abgearbeitet. Wenn Sie ins Setup

gelangen wollen, nachdem der POST durchgeführt wurde, müssen Sie das System
über die Tastenkombination <Ctrl> + <Alt> + <Delete> oder den Reset-Knopf auf
der Gehäusevorderseite, neu starten. Natürlich können Sie einen Neustart auch
durchführen, indem Sie das System kurz ab- und danach wieder anschalten.
Das Setup-Programm ist für eine bequeme Bedienung entwickelt worden. Es ist
ein menügesteuertes Programm, in dem Sie durch unterschiedliche Untermenüs
scrollen und die vorab festgelegten Optionen auswählen können. Für detaillierte
Informationen zum BIOS-Setup, siehe bitte das Benutzerhandbuch (PDF Datei) auf
der Support CD.

3. Software Support CD information

Dieses Motherboard unterstützt eine Reiche von Microsoft® Windows® Betriebs­systemen: 8 / 8 64-Bit / 7 / 7 64-Bit / VistaTM / Vista
Ihrem Motherboard beigefügte Support-CD enthält hilfreiche Software, Treiber und
Hilfsprogramme, mit denen Sie die Funktionen Ihres Motherboards verbessern kön­nen Legen Sie die Support-CD zunächst in Ihr CD-ROM-Laufwerk ein. Der Willkom­mensbildschirm mit den Installationsmenüs der CD wird automatisch aufgerufen,
wenn Sie die “Autorun”-Funktion Ihres Systems aktiviert haben.
Erscheint der Wilkommensbildschirm nicht, so “doppelklicken” Sie bitte auf das File
ASSETUP.EXE im BIN-Verzeichnis der Support-CD, um die Menüs aufzurufen.
Das Setup-Programm soll es Ihnen so leicht wie möglich machen. Es ist menüges­teuert, d.h. Sie können in den verschiedenen Untermenüs Ihre Auswahl treffen und

die Programme werden dann automatisch installiert.

TM

64-Bit / XP / XP 64-Bit. Die

Deutsch

34

ASRock H61 Pro BTC Motherboard

1. Introduction

Merci pour votre achat d’une carte mère ASRock H61 Pro BTC, une carte mère

très able produite selon les critères de qualité rigoureux de ASRock. Elle offre des

performances excellentes et une conception robuste conformément à l’engagement

d’ASRock sur la qualité et la abilité au long terme.
Ce Guide d’installation rapide présente la carte mère et constitue un guide

d’installation pas à pas. Des informations plus détaillées concernant la carte

mère pourront être trouvées dans le manuel l’utilisateur qui se trouve sur le CD

d’assistance.

Les spécications de la carte mère et le BIOS ayant pu être mis à

jour, le contenu de ce manuel est sujet à des changements sans

notication. Au cas où n’importe qu’elle modication intervenait sur ce

manuel, la version mise à jour serait disponible sur le site web

ASRock sans nouvel avis. Vous trouverez les listes de prise en
charge des cartes VGA et CPU également sur le site Web ASRock.

Site web ASRock, http://www.asrock.com
Si vous avez besoin de support technique en relation avec cette carte

mère, veuillez consulter notre site Web pour de plus amples
informations particulières au modèle que vous utilisez.

www.asrock.com/support/index.asp

1.1 Contenu du paquet

Carte mère ASRock H61 Pro BTC (Facteur de forme ATX)
Guide d’installation rapide ASRock H61 Pro BTC

CD de soutien ASRock H61 Pro BTC

Deux câbles de données de série ATA (SATA) (en option)

Un I/O Panel Shield

ASRock vous rappelle...

Pour bénécier des meilleures performances sous Windows® 8 / 8 64 bits
/ 7 / 7 64 bits / Vista
l'option BIOS dans Conguration de stockage en mode AHCI. Pour plus
de détails sur l'installation BIOS, référez-vous au "Mode d'emploi" sur
votre CD de support.

TM

/ VistaTM 64 bits, il est recommandé de paramétrer

ASRock H61 Pro BTC Motherboard

Français

35

Français

1.2 Spécications

Format - Facteur de forme ATX



- Conception à condensateur robuste
CPU - Prend en charge les processeurs Intel® CoreTM i7 / i5 / i3 /

Xeon® / Pentium® / Celeron® 2ème et 3ème génération sur

socket LGA1155

- Prend en charge la technologie Intel® Turbo Boost 2.0

- Prise en charge des unités centrales non verrouillées de

série K
Chipsets - Intel® H61

- Prend en charge les technologies Intel® Rapid Start et Smart
Connect
Mémoire - Compatible avec la Technologie de Mémoire à Canal

Double

- 2 x slots DIMM DDR3

- Supporter DDR3 1600/1333/1066 non-ECC, sans
amortissement mémoire (DDR3 1600 avec CPU Intel® Ivy
Bridge, DDR3 1333 avec CPU Intel® Sandy Bridge)

- Capacité maxi de mémoire système: 16GB

- Prend en charge le prol de mémoire extrême Intel® (XMP)

1.3/1.2 avec processeur Intel® Ivy Bridge CPU
Slot d’extension - 1 x slot PCI Express 3.0 x16 (PCIE2 @ mode x16)
* PCIE 3.0 n’est pris en charge qu’avec le processeur Intel®
Ivy Bridge. Avec le processeur Intel® Sandy Bridge, seul
PCIE 2.0 est pris en charge.

- 5 x slot PCI Express 2.0 x1
VGA sur carte * Intel® HD Graphics avec visuels intégrés (Built-in Visuals) et
les sorties VGA sont uniquement pris en charge par les
processeurs à GPU intégré.

- Supporte Intel® HD Graphics Built-in Visuals: Intel® Quick
Sync Video 2.0, Intel® InTruTM 3D, Intel® Clear Video HD
Technology, Intel® InsiderTM, Intel® HD Graphics 2500/4000
avec processeur Intel® Ivy Bridge CPU

- Supporte Intel® HD Graphics Built-in Visuals: Intel® Quick
Sync Video, Intel® InTruTM 3D, Intel® Clear Video HD
Technology, Intel® HD Graphics 2000/3000, Intel® Advanced
Vector Extensions (AVX) avec processeur Intel® Sandy
Bridge CPU

- Pixel Shader 5.0, DirectX 11 avec CPU Intel® Ivy Bridge,
Pixel Shader 4.1, DirectX 10.1 avec CPU Intel® Sandy

36

ASRock H61 Pro BTC Motherboard

Bridge

- Mémoire partagée max 1760MB avec processeur Intel® Ivy
Bridge CPU. Mémoire partagée max 1759MB avec
processeur Intel® Sandy Bridge CPU.

- Output de VGA Duel: supporter HDMI et D-Sub ports par

les controleurs de display independents

- Prend en charge le HDMI avec une résolution
maximale jusqu’à 1920x1200 @ 60Hz

- Prend en charge le D-Sub avec une résolution maximale

jusqu’à 2048x1536 @ 75Hz

- Prend en charge Lip Sync, Deep Color (12bpc), xvYCC et
HBR (High Bit Rate Audio : Audio à haut débit binaire) avec
HDMI (Moniteur compatible HDMI requis)

- Prise en charge de la fonction HDCP avec port HDMI

- Supporter 1080p Blu-ray(BD)/ lecteur de HD-DVD avec
port HDMI

Audio - 5.1 Son haute dénition de CH (codec audio VIA® VT1705)
LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Support du Wake-On-LAN

- Prise en charge de la détection de câble LAN

- Prend en charge la norme Energy Efcient Ethernet
(Ethernet à efcacité énergétique) 802.3az

- Supporte PXE

Panneau arrière - 1 x port souris PS/2

- 1 x port clavier PS/2

- 1 x port D-Sub

- 1 x port HDMI

- 6 x ports USB 2.0 par défaut

- 1 x port LAN RJ-45 avec LED (ACT/LED CLIGNOTANTE et
LED VITESSE)

- Prise HD Audio: Entrée Ligne / Haut-parleur frontal /

Microphone

Stockage - 4 x connecteurs SATA2, prennent en charge un taux de

transfert de données pouvant aller jusqu’à 3.0Go/s,

supporte NCQ, AHCI et « Hot Plug » (Branche ment à

chaud)
Connecteurs - 1 x En-tête du module infrarouge

- 1 x En-tête de port COM

- 1 x Connecteur pour ventilateur de CPU (br. 4)

- 1 x Connecteur pour ventilateur de Châssis (br. 4)

Français

ASRock H61 Pro BTC Motherboard

37

- 1 x Connecteur pour ventilateur de pouvoir (br. 4)

- 1 x br. 24 connecteur d’alimentation ATX

- 1 x br. 8 connecteur d’alimentation 12V ATX

- 2 x Connecteur d’alimentation SLI/XFire

- 1 x Connecteur audio panneau avant

- 2 x En-tête USB 2.0 (prendre en charge 4 ports USB 2.0

supplémentaires)

BIOS - 32Mb AMI UEFI Legal BIOS avec support GUI

- Support du “Plug and Play”

- Compatible pour événements de réveil ACPI 1.1

- Gestion jumperless

- Support SMBIOS 2.3.1

- IGPU, DRAM, PCH, CPU PLL, VTT, VCCSA Tension

Multi-ajustement
CD d’assistance - Pilotes, utilitaires, logiciel anti-virus (version d’évaluation),

Google Chrome Browser et Toolbar
Surveillance - Contrôle de la température CPU

système - Mesure de température de la carte mère

- Tachéomètre ventilateur processeur/châssis/ventilateur

- Ventilateur silencieux pour unité centrale/châssis (permet le

réglage automatique de la vitesse du ventilateur pour châs­sis, selon la température de l’unité centrale)

- Commande de ventilateur CPU/châssis à plusieurs vitesses

- Monitoring de la tension: +12V, +5V, +3.3V, Vcore

OS - Microsoft® Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM /

Vista

TM

64-bit / XP / XP 64-bit

Certications - FCC, CE, WHQL

- Prêt pour ErP/EuP (alimentation Prêt pour ErP/EuP requise)

* Pour de plus amples informations sur les produits, s’il vous plaît visitez notre site web:

http://www.asrock.com

Français

38

ASRock H61 Pro BTC Motherboard

1.3 Réglage des cavaliers

L’illustration explique le réglage des cava­liers. Quand un capuchon est placé sur les
broches, le cavalier est « FERME ». Si au­cun capuchon ne relie les broches,le cava-

lier est « OUVERT ». L’illustration montre un
cavalier à 3 broches dont les broches 1 et 2
sont « FERMEES » quand le capuchon est
placé sur ces 2 broches.

Le cavalier Description

Effacer la CMOS

(CLRCMOS1)
(voir p.2 g. 9)

Remarque :

Paramètres
par défaut

CLRCMOS1 vous permet d’effacer les données du CMOS. Pour effacer
et réinitialiser les paramètres du système à la conguration originale,
veuillez éteindre l’ordinateur et débrancher le cordon d’alimentation de
la prise de courant. Après 15 secondes, utilisez un couvercle de jumper
pour court-circuiter les broches pin2 et pin3 de CLRCMOS1 pendant
secondes. Veuillez cependant ne pas effacer le CMOS immédiatement

a

près avoir mis à jour le BIOS. Si vous avez besoin d’effacer le CMOS

après avoir mis à jour le BIOS, vous devez allumer en premier le

système, puis l’éteindre avant de continuer avec l’opération d’effacement

du CMOS. Veuillez noter que le mot de passe, la date, l’heure, le prol
par défaut de l’utilisateur, 1394 GUID et l’adresse MAC seront effacés
seulement si la batterie du CMOS est enlevée.

Effacer la

CMOS

5

ASRock H61 Pro BTC Motherboard

Français

39

1.4 En-têtes et Connecteurs sur Carte

Connecteurs Série ATAII Ces quatre connecteurs Série

(SATA2_0: voir p.2 No. 12)

(SATA2_1: voir p.2 No. 15)

(SATA2_2: voir p.2 No. 11)

(SATA2_3: voir p.2 No. 14)

actuelle permet des taux
transferts de données pouvant

aller jusqu’à 3,0 Gb/s.

Câble de données Toute cote du cable de data

Série ATA (SATA) SATA peut etre connecte au

(en option)

ou au connecteur SATAII sur la

carte mere.

Les en-têtes et connecteurs sur carte NE SONT PAS des cavaliers.
NE PAS placer les capuchons de cavalier sur ces en-têtes et con­necteurs. Le fait de placer les capuchons de cavalier sur les en-têtes
et connecteurs causera à la carte mère des dommages irréversibles!

ATAII (SATAII) prennent en

SATA2_0

SATA2_2

charge les câbles SATA pour
les périphériques de stockage

internes. L’interface SATAII

SATA2_1

SATA2_3

disque dur SATA / SATAII /

Français

40

1

1

USB _PWR

P-9

P-8

USB _PWR

USB _PWR

P-11

P-10

USB _PWR

P+9

P+8

P+1 1

P+1 0

GND

GND

GND

GND

DUM MY

DUM MY

En-tête USB 2.0 A côté des six ports

(USB6_7 br.9)

(voir p.2 No. 18)

USB 2.0 par défaut sur le

panneau E/S, il y a deux

embases USB 2.0 sur cette
carte mère. Chaque embase
USB 2.0 peut prendre en

(USB8_9 br.9)

(voir p.2 No. 17)

charge 2 ports USB 2.0.

En-tête du module infrarouge Cet en-tête supporte un module

(IR1 br.5)

infrarouge optionnel de

(voir p.2 No. 13)

transfert et de réception sans

l.

ASRock H61 Pro BTC Motherboard

Connecteur audio panneau C’est une interface pour

(HD_AUDIO1 br. 9)

(voir p.2 No. 20)

un câble avant audio en façade

qui permet le branchement et

le contrôle commodes de

périphériques audio.

1

GND

PRE SENC E#

MIC 2_R

MIC 2_L

MIC _RET

J_S ENSE

OUT 2_R

OUT _RET

OUT 2_L

1. L’audio à haute dénition (HDA) prend en charge la détection de che,
mais le l de panneau sur le châssis doit prendre en charge le HDA pour
fonctionner correctement. Veuillez suivre les instructions dans notre
manuel et le manuel de châssis an installer votre système.

2. Si vous utilisez le panneau audio AC’97, installez-le sur l’adaptateur audio

du panneau avant conformément à la procédure ci-dessous :

A. Connectez Mic_IN (MIC) à MIC2_L.
B. Connectez Audio_R (RIN) à OUT2_R et Audio_L (LIN) à OUT2_L.
C. Connectez Ground (GND) à Ground (GND).
D. MIC_RET et OUT_RET sont réservés au panneau audio HD. Vous
n’avez pas besoin de les connecter pour le panneau audio AC’97.

En-tête du panneau système Cet en-tête permet d’utiliser

(PANEL1 br.9)

(voir p.2 No. 16)

Connectez l’interrupteur d’alimentation, l’interrupteur de réinitialisation et

l’indicateur d’état du système du châssis sur cette barrette en respectant
l’affectation des broches décrite ci-dessous. Faites attention aux broches
positives et négatives avant de connecter les câbles.

plusieurs fonctions du

panneau système frontal.

PWRBTN (Interrupteur d’alimentation):

Connectez ici le connecteur d’alimentation sur le panneau avant du
châssis. Vous pouvez congurer la façon de mettre votre système hors

tension avec l’interrupteur d’alimentation.

RESET (Interrupteur de réinitialisation):

Connectez ici le connecteur de réinitialisation sur le panneau avant du
châssis. Appuyez sur l’interrupteur de réinitialisation pour redémarrer

l’ordinateur s’il se bloque ou s’il n’arrive pas à redémarrer normalement.

PLED (DEL alimentation système):

Connectez ici l’indicateur d’état de l’alimentation sur le panneau avant
du châssis. Ce voyant DEL est allumé lorsque le système est en

marche. Le voyant DEL clignote lorsque le système est en mode veille
S1. Le voyant DEL est éteint lorsque le système est en mode veille S3/

S4 ou lorsqu’il est éteint (S5).

ASRock H61 Pro BTC Motherboard

Français

41

HDLED (DEL activité du disque dur):

Connectez ici le voyant DEL d’activité du disque dur sur le panneau
avant du châssis. Ce voyant DEL est allumé lorsque le disque dur est en

train de lire ou d’écrire des données.

Le design du panneau avant peut varier en fonction du châssis. Un

module de panneau avant consiste principalement en : interrupteur
d’alimentation, interrupteur de réinitialisation, voyant DEL d’alimentation,
voyant DEL d’activité du disque dur, haut-parleur, etc. Lorsque vous

connectez le panneau avant de votre châssis sur cette barrette, vériez
bien à faire correspondre les ls et les broches.

En-tête du haut-parleur Veuillez connecter le

de châssis haut-parleur de châssis sur

(SPEAKER1 br. 4)

(voir p.2 No. 10)

cet en-tête.

Français

Connecteur pour châssis et ventilateur

(CHA_FAN1 br. 4)

(voir p.2 No. 6)

Branchez les câbles du

ventilateur aux connecteurs pour
ventilateur et faites correspondre

le l noir à la broche de terre.

(PWR_FAN1 br. 4)

(voir p.2 No. 28)

Connecteur du ventilateur Veuillez connecter le câble de
de l’UC ventilateur d’UC sur ce

(CPU_FAN1 br. 4)

(voir p.2 No. 2)

Bien que cette carte mère offre un support de (Ventilateur silencieux
ventilateur de CPU à 4 broches , le ventilateur de CPU à 3 broches peut

bien fonctionner même sans la fonction de commande de vitesse du

ventilateur. Si vous prévoyez de connecter le ventilateur de CPU à 3
broches au connecteur du ventilateur de CPU sur cette carte mère,
veuillez le connecter aux broches 1-3.

FAN_ SPEE D_CO NTRO L

CPU _FAN_ SPEE D

+12 V

connecteur et brancher le l

noir sur la broche de terre.

GND

1 2 3 4

Installation de ventilateur à 3 broches

Broches 1-3 connectées

42

ASRock H61 Pro BTC Motherboard

En-tête d’alimentation ATX Veuillez connecter l’unité

(ATXPWR1 br. 24)

(voir p.2 No. 5)

d’alimentation ATX sur cet en-

tête.

12 124

13

Bien que cette carte mère fournisse un connecteur de

courant ATX 24 broches, elle peut encore fonctionner

12

24

si vous adopter une alimentation traditionnelle ATX 20
broches. Pour utiliser une alimentation ATX 20 broches,
branchez à l’alimentation électrique ainsi qu’aux

broches 1 et 13.

20-Installation de l’alimentation électrique ATX

Connecteur ATX 12V Veuillez connecter une unité

(ATX12V1 br.8)

(voir p.2 No. 3)

d’alimentation électrique ATX

12V sur ce connecteur.

8 5

4 1

1

13

Bien que cette carte mère possède 8 broches connecteur d’alimentation

ATX 12V, il peut toujours travailler si vous adoptez une approche
traditionnelle à 4 broches ATX 12V alimentation. Pour utiliser
l’alimentation des 4 broches ATX, branchez votre alimentation
avec la broche 1 et la broche 5.

4-Installation d’alimentation à 4 broches ATX 12V

8 5

4 1

En-tête de port COM Cette en-tête de port COM est

(COM1 br.9)

(voir p.2 No. 19)

utilisée pour prendre en charge

un module de port COM.

Connecteur d’alimentation SLI/XFire

(SLI/XFIRE_PWR1 br. 4)

(voir p.2 No. 29)

(SLI/XFIRE_PWR2 br. 4)

(voir p.2 No. 27)

ASRock H61 Pro BTC Motherboard

Veuillez brancher ce connecteur

avec un connecteur d’alimen­tation de alimentation lorsque
trois cartes graphiques sont
installées sur la carte mère.

Français

43

2. Informations sur le BIOS

La puce Flash Memory sur la carte mère stocke le Setup du BIOS. Lorsque vous
démarrez l’ordinateur, veuillez presser <F2> ou <Del> pendant le POST (Power-On-
Self-Test) pour entrer dans le BIOS; sinon, le POST continue ses tests de routine. Si
vous désirez entrer dans le BIOS après le POST, veuillez redémarrer le système en
pressant <Ctl> + <Alt> + <Suppr>, ou en pressant le bouton de reset sur le boîtier
du système. Vous pouvez également redémarrer en éteignant le système et en le
rallumant. L’utilitaire d’installation du BIOS est conçu pour être convivial. C’est un
programme piloté par menu, qui vous permet de faire déler par ses divers sous-

menus et de choisir parmi les choix prédéterminés. Pour des informations détaillées

sur le BIOS, veuillez consulter le Guide de l’utilisateur (chier PDF) dans le CD

technique.

3. Informations sur le CD de support

Cette carte mère supporte divers systèmes d’exploitation Microsoft® Windows®:
8 / 8 64 bits / 7 / 7 64 bits / VistaTM / Vista

nique livré avec cette carte mère contient les pilotes et les utilitaires nécessaires

pour améliorer les fonctions de la carte mère. Pour utiliser le CD technique, insérez­le dans le lecteur de CD-ROM. Le Menu principal s’afche automatiquement si
“AUTORUN” est activé dans votre ordinateur. Si le Menu principal n’apparaît pas
automatiquement, localisez dans le CD technique le chier “ASSETUP.EXE” dans le
dossier BIN et double-cliquez dessus pour afcher les menus.

TM

64 bits / XP / XP 64 bits. Le CD tech-

Français

44

ASRock H61 Pro BTC Motherboard

1. Introduzione

Grazie per aver scelto una scheda madre ASRock H61 Pro BTC, una scheda
madre afdabile prodotta secondo i severi criteri di qualità ASRock. Le prestazioni

eccellenti e il design robusto si conformano all’impegno di ASRock nella ricerca

della qualità e della resistenza.
Questa Guida Rapida all’Installazione contiene l’introduzione alla motherboard e la
guida passo-passo all’installazione. Informazioni più dettagliate sulla motherboard si
possono trovare nel manuale per l’utente presente nel CD di supporto.

Le speciche della scheda madre e il software del BIOS possono

essere aggiornati, pertanto il contenuto di questo manuale può subire

variazioni senza preavviso. Nel caso in cui questo manuale sia
modicato, la versione aggiornata sarà disponibile sul sito di ASRock
senza altro avviso. Sul sito ASRock si possono anche trovare le più
recenti schede VGA e gli elenchi di CPU supportate.

ASRock website http://www.asrock.com
Se si necessita dell’assistenza tecnica per questa scheda madre,

visitare il nostro sito per informazioni speciche sul modello che si

sta usando.
www.asrock.com/support/index.asp

1.1 Contenuto della confezione

Scheda madre ASRock H61 Pro BTC (ATX Form Factor)

Guida di installazione rapida ASRock H61 Pro BTC
CD di supporto ASRock H61 Pro BTC
Due cavi dati Serial ATA (SATA) (opzionali)
Un I/O Shield

ASRock vi ricorda...

Per ottenere migliori prestazioni in Windows® 8 / 8 64-bit / 7 / 7 64-bit /

TM

Vista

/ VistaTM 64-bit, si consiglia di impostare l'opzione BIOS in Storage
Conguration (Congurazione di archiviazione) sulla modalità AHCI. Per
l'impostazione BIOS, fare riferimento a “User Manual” (Manuale dell'uten­te) nel CD di supporto per dettagli.

ASRock H61 Pro BTC Motherboard

Italiano

45

Italiano

1.2 Speciche

Piattaforma - ATX Form Factor

- Design condensatore robusto

Processore - Supporta Intel® CoreTM i7 / i5 / i3 / Xeon® / Pentium® / Celeron®
di 3a e 2a generazione in un pacchetto LGA1155

- Supporto della tecnologia Intel® Turbo Boost 2.0

- Supporta CPU unlocked serie K
Chipset - Intel® H61

- Supporta tecnologia Intel® Rapid Start Technology e Smart
Connect Technology
Memoria - Supporto tecnologia Dual Channel Memory

- 2 x slot DDR3 DIMM

- Supporto DDR3 1600/1333/1066 non-ECC, momoria senza
buffer (DDR3 1600 con CPU Intel® Ivy Bridge, DDR3 1333 con
CPU Intel® Sandy Bridge)

- Capacità massima della memoria di sistema: 16GB

- Supporto di Intel® XMP (Extreme Memory Prole)1.3/1.2 con
CPU Intel® Ivy Bridge

Slot di - 1 x Alloggi PCI Express 3.0 x16 (PCIE2 a modalità x16)
espansione * PCIE 3.0 è supportato soltanto con la CPU Intel® Ivy Bridge.

Con la CPU Intel® Sandy Bridge, supporta solamente PCIE

2.0.

- 5 x Alloggi PCI Express 2.0 x1
VGA su scheda * Le uscite Intel® HD Graphics Built-in Visuals e VGA possono
essere supportate solo con processori dotati di GPU

integrata.

- Supporta Intel® HD Graphics Built-in Visuals: Intel® Quick Sync

Video 2.0, Intel® InTruTM 3D, Intel® Clear Video HD Technology,
Intel® InsiderTM, Intel® HD Graphics 2500/4000 con CPU Intel®
Ivy Bridge

- Supporta Intel® HD Graphics Built-in Visuals: Intel® Quick Sync
Video, Intel® InTruTM 3D, Intel® Clear Video HD Technology,
Intel® HD Graphics 2000/3000, Intel® Advanced Vector
Extensions (AVX) con CPU Intel® Sandy Bridge

- Pixel Shader 5.0, DirectX 11 con CPU Intel® Ivy Bridge, Pixel
Shader 4.1, DirectX 10.1 con CPU Intel® Sandy Bridge

- Memoria massima condivisa 1760MB con CPU Intel®
Ivy Bridge. Memoria massima condivisa 1759MB con CPU
Intel® Sandy Bridge.

- Uscita VGA Doppia: supporto porte HDMI e D-Sub tramite

46

ASRock H61 Pro BTC Motherboard

vericatore display indipendente

- Supporta HDMI con risoluzione massima no a 1920x1200 @
60Hz

- Supporta D-Sub con risoluzione massima no a 2048x1536 @
75Hz

- Supporto delle funzioni Auto Lip Sync, Deep Color (12bpc),
xvYCC e HBR (High Bit Rate Audio) con HDMI (è necessario
un monitor compatibile HDMI)

- Supporto della funzione HDCP con le porte HDMI

- Supporto 1080p Blu-ray (BD) / HD-DVD riproduzione con le
porte HDMI
Audio - 5.1 Audio HD CH (VIA® VT1705 Audio Codec)

LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Supporta Wake-On-LAN

- Supporta il rilevamento cavo LAN

- Supporto di Energy Efcient Ethernet 802.3az

- Supporta PXE
Pannello - 1 x porta PS/2 per mouse
posteriore I/O - 1 x porta PS/2 per tastiera

- 1 x porta D-Sub

- 1 x porta HDMI

- 6 x porte USB 2.0 già integrate

- 1 x porte LAN RJ-45 con LED (LED azione/collegamento e

LED velocità)

- Connettore HD Audio: ingresso linea / cassa frontale /

microfono
Interfaccia di - 4 x connettori SATA2 3.0Go/s, sopporta delle funzioni NCQ,
storage AHCI e “Hot Plug”
Connettori - 1 x Collettore modulo infrarossi

- 1 x collettore porta COM

- 1 x Connettore CPU ventola (4-pin)

- 1 x Connettore Chassis ventola (4-pin)

- 1 x Connettore Alimentazione ventola (4-pin)

- 1 x 24-pin collettore alimentazione ATX

- 1 x 8-pin connettore ATX 12V

- 2 x Collettore alimentazione SLI/XFire

- 1 x Connettore audio sul pannello frontale

- 2 x Collettore USB 2.0 (supporta 4 porte USB 2.0)
BIOS - 32Mb AMI UEFI Legal BIOS con interfaccia di supporto

- Supporta “Plug and Play”

Italiano

ASRock H61 Pro BTC Motherboard

47

- Compatibile con ACPI 1.1 wake up events

- Supporta jumperfree

- Supporta SMBIOS 2.3.1

- Regolazione multi-voltaggio IGPU, DRAM, PCH, CPU PLL,
VTT, VCCSA

CD di - Driver, Utilità, Software AntiVirus (versione di prova),
supporto CyberLink MediaEspresso 6.5 Trial, Google Chrome Browser

e Toolbar
Monitoraggio - Sensore per la temperatura del processore
Hardware - Sensore temperatura scheda madre

- Indicatore di velocità per la ventola del CPU/Chassis/
Alimentazione

- Ventola CPU/Chassis silenziosa (permette la regolazione
automatica della ventola dello chassis in base alla temperatura

della CPU madre)

- Ventola CPU/Chassis con controllo di varie velocità

- Voltaggio: +12V, +5V, +3.3V, Vcore

Compatibi- - Microsoft® Windows® 8 / 8 64 bit / 7 / 7 64 bit / VistaTM / Vista

TM

lità SO 64 bit / XP / XP 64 bit

Certicazioni - FCC, CE, WHQL

- Predisposto ErP/EuP (è necessaria l’alimentazione

predisposta per il sistema ErP/EuP)

* Per ulteriori informazioni, prego visitare il nostro sito internet: http://www.asrock.com

Italiano

48

ASRock H61 Pro BTC Motherboard

1.3 Setup dei Jumpers

L’illustrazione mostra come sono settati i jump­er. Quando il ponticello è posizionato sui pin,
il jumper è “CORTOCIRCUITATO”. Se sui pin
non ci sono ponticelli, il jumper è “APERTO”.
L’illustrazione mostra un jumper a 3 pin in cui il
pin1 e il pin2 sono “CORTOCIRCUITATI” quan­do il ponticello è posizionato su questi pin.

Jumper Settaggio del Jumper

Resettare la CMOS

(CLRCMOS1)
(vedi p.2 item 9)

Nota:

CLRCMOS1 permette si azzerare i dati nella CMOS. Per cancellare e ripristinare

i

parametri del sistema sulla congurazione iniziale, spegnere il computer e

Impostazione

predenita

scollegare il cavo d’alimentazione dalla presa di corrente. Attendere 15 secondi,
poi usare un cappuccio jumper per cortocircuitare il pin 2 ed il pin 3 su
CLRCMOS1 per 5 secondi. Tuttavia, si consiglia di non cancellare la CMOS
subito dopo avere aggiornato il BIOS. Se si deve azzerare la CMOS quando si
è completato l’aggiornamento del BIOS, è necessario per prima cosa avviare
il sistema e poi spegnerlo prima di eseguire l’azzeramento della CMOS. No­tare che password, data, ore, prolo utente predenito, 1394 GUID e indirizzo
MAC saranno cancellati solo se è rimossa la batteria della CMOS.

Azzeramen-

to CMOS

ASRock H61 Pro BTC Motherboard

Italiano

49

Italiano

1.4 Collettori e Connettori su Scheda

Connettori Serial ATAII Questi quattro connettori Serial

(SATA2_0: vedi p.2 Nr. 12)

(SATA2_1: vedi p.2 Nr. 15)

(SATA2_2: vedi p.2 Nr. 11)

(SATA2_3: vedi p.2 Nr. 14)

SATA per dispositivi di memoria

interni. L’interfaccia SATAII

attuale permette velocità di

trasferimento dati no a

3.0 Gb/s.

Cavi dati Serial ATA (SATA) Una o altra estremità del cavo

(Opzionale)

collegata al disco rigido SATA /

SATAII o al connettore
di SATAII su questa

cartolina base.

Collettore USB 2.0 Oltre alle sei porte USB 2.0

(9-pin USB6_7)

(vedi p.2 Nr. 18)

due intestazioni USB 2.0.
Ciascuna intestazione USB 2.0
supporta due porte USB 2.0.

(9-pin USB8_9)
(vedi p.2 Nr. 17)

Collettore modulo infrarossi Questo collettore supporta

(5-pin IR1)

(vedi p.2 Nr. 13)

ricezione senza li.

I collettori ed i connettori su scheda NON sono dei jumper. NON instal­lare cappucci per jumper su questi collettori e connettori. L’installazione

di cappucci per jumper su questi collettori e connettori provocherà
danni permanenti alla scheda madre!

ATAII (SATAII) supportano cavi

SATA2_0

SATA2_2

dati SATA per dispositivi di

immagazzinamento interni.

SATA2_1

ATAII (SATAII) supportano cavi

SATA2_3

di dati SATA può essere

predenite nel pannello I/O, la

scheda madre dispone di

USB _PWR

P-9

P+9

GND

DUM MY

1

GND

P+8

P-8

USB _PWR

moduli ad infrarossi optional

per la trasmissione e la

50

ASRock H61 Pro BTC Motherboard

1

GND

PRE SENC E#

MIC 2_R

MIC 2_L

MIC _RET

J_S ENSE

OUT 2_R

OUT _RET

OUT 2_L

Connettore audio sul È un’interfaccia per il cavo del
pannello frontale pannello audio. Che consente

(9-pin HD_AUDIO1)

(vedi p.2 Nr. 20)

connessione facile e controllo

dei dispositivi audio.

1. La caratteristica HDA (High Denition Audio) supporta il rilevamento dei
connettori, però il pannello dei cavi sul telaio deve supportare la funzione
HDA (High Denition Audio) per far sì che questa operi in modo corretto.
Attenersi alle istruzioni del nostro manuale e del manuale del telaio per

installare il sistema.

2. Se si utilizza un pannello audio AC’97, installarlo nell’intestazione audio

del pannello anteriore, come indicato di seguito:

A. Collegare Mic_IN (MIC) a MIC2_L.
B. Collegare Audio_R (RIN) a OUT2_R e Audio_L (LIN) ad OUT2_L.
C. Collegare Ground (GND) a Ground (GND).

D. MIC_RET e OUT_RET sono solo per il pannello audio HD. Non è

necessario collegarli per il pannello audio AC’97.

Collettore pannello di sistema Questo collettore accomoda

(9-pin PANEL1)

(vedi p.2 Nr. 16)

diverse funzioni di sistema

pannello frontale.

Collegare l’interruttore d’alimentazione, l’interruttore di ripristino,

l’indicatore di stato del sistema del pannello frontale del telaio a questo

header in base all’assegnazione dei pin denita di seguito. Determinare i

pin positivi e negativi prima di collegare i cavi.

PWRBTN (interruttore d’alimentazione):

Va collegato all’interruttore d’alimentazione del pannello frontale del
telaio. Usando l’interruttore d’alimentazione si può congurare il modo in

cui si spegne il sistema.

RESET (interruttore di ripristino):

Va collegato all’interruttore di ripristino del pannello frontale del telaio.

Premere l’interruttore di ripristino per riavviare il sistema se il computer si
blocca e non riesce ad eseguire un normale riavvio.

PLED (LED alimentazione del sistema):

Va collegato all’indicatore di stato d’alimentazione del pannello frontale
del telaio. Il LED è acceso quando il sistema è operativo. Il LED continua
a lampeggiare quando il sistema è in stato di standby S1. Il LED è
spento quando il sistema è in stato di sospensione /ibernazione S3/S4
oppure spento (S5).

ASRock H61 Pro BTC Motherboard

Italiano

51

HDLED (LED attività disco rigido):

Va collegato al LED attività disco rigido del pannello frontale del telaio. Il

LED è acceso quando disco rigido legge e scrive i dati.

Il design del pannello frontale può variare in base ai telai. Il modulo di
un pannello frontale può consistere di: interruttore d’alimentazione,
interruttore di ripristino, LED d’alimentazione, LED attività disco rigido,

casse, eccetera. Quando si collega il modulo del pannello frontale a

questo header, assicurarsi che l’assegnazione dei li e dei pin sia fatta

corrispondere in modo appropriato.

Collettore casse telaio Collegare le casse del telaio a

(4-pin SPEAKER1)

(vedi p.2 Nr. 10)

questo collettore.

Collettori Chassis ed alimentazione ventola Collegare i cavi della ventola ai

(4-pin CHA_FAN1)

(vedi p.2 Nr. 6)

corrispondenti connettori

facendo combaciare il cavo

nero col pin di terra.

(4-pin PWR_FAN1)

(vedi p.2 Nr. 28)

Italiano

52

Connettore ventolina CPU Collegare il cavo della ventolina

(4-pin CPU_FAN1)

(vedi p.2 Nr. 2)

CPU a questo connettore e far

combaciare il lo nero al pin

terra.

FAN_ SPEE D_CO NTRO L

CPU _FAN_ SPEE D

+12 V

GND

1 2 3 4

Sebbene la presente scheda madre disponga di un supporto per ventola

CPU a 4 piedini (ventola silenziosa), la ventola CPU a 3 piedini è in
grado di funzionare anche senza la funzione di controllo della velocità
della ventola. Se si intende collegare la ventola CPU a 3 piedini al
connettore della ventola CPU su questa scheda madre, collegarla ai

piedini 1-3.

Piedini 1-3 collegati

Installazione della ventola a 3 piedini

Connettore alimentazione ATX Collegare la sorgente

(24-pin ATXPWR1)

(vedi p.2 Nr. 5)

d’alimentazione ATX a questo

connettore.

12 124

13

ASRock H61 Pro BTC Motherboard

Con questa scheda madre, c’è in dotazione un
connettore elettrico ATX a 24 pin, ma può funzionare lo
stesso se si adotta un alimentatore ATX a 20 pin. Per
usare l’alimentatore ATX a 20 pin, collegare l’alimentatore

con il Pin 1 e il Pin 13.

12

24

Installazione dell’alimentatore ATX a 20 pin

Connettore ATX 12 V Collegare un alimentatore ATX

(8-pin ATX12V1)

(vedi p.2 Nr. 3)

12 V a questo connettore.

8 5

4 1

1

13

Sebbene questa schedamadre fornisca un connettore elettrico 8-pin ATX

12V, l‘unita‘ puo‘ ancora essere funzionante se viene utilizzata una
fornitura elettrica tradizionale a 4-pin ATX 12V. Per usare tale fornitura
elettrica 4-pin ATX 12V, prego collegare la presa elettrica
al Pin 1 e Pin 5.

Installazione elettrica 4-Pin ATX 12V

8 5

4 1

Collettore porta COM Questo collettore porta COM è

(9-pin COM1)

(vedi p.2 Nr. 19)

Connettore alimentazione SLI/XFire

(4-pin SLI/XFIRE_PWR1)

(vedi p.2 Nr. 29)

utilizzato per supportare il

modulo porta COM.

Collegare questo connettore al
connettore di alimentazione di
un’alimentazione quando le tre
schede grache sono installate

(4-pin SLI/XFIRE_PWR2)

(vedi p.2 Nr. 27)

su questa scheda madre.

ASRock H61 Pro BTC Motherboard

Italiano

53

2. Informazioni sul BIOS

La Flash Memory sulla scheda madre contiene le Setup Utility. Quando si avvia il
computer, premi <F2> o <Del> durante il Power-On-Self-Test (POST) della Setup
utility del BIOS; altrimenti, POST continua con i suoi test di routine. Per entrare il
BIOS Setup dopo il POST, riavvia il sistema premendo <Ctl> + <Alt> + <Delete>, o
premi il tasto di reset sullo chassis del sistema. Per informazioni più dettagliate circa
il Setup del BIOS, fare riferimento al Manuale dell’Utente (PDF le) contenuto nel cd

di supporto.

3. Software di supporto e informazioni su

CD

Questa scheda madre supporta vari sistemi operativi Microsoft® Windows®: 8 /

8 64-bit / 7 / 7 64-bit / VistaTM / Vista
redo della scheda madre contiene i driver e utilità necessari a potenziare le caratter-

istiche della scheda.

Inserire il CD di supporto nel lettore CD-ROM. Se la funzione “AUTORUN” è attivata
nel computer, apparirà automaticamente il Menù principale. Se il Menù principale
non appare automaticamente, posizionarsi sul le “ASSETUP.EXE” nel CESTINO
del CD di supporto e cliccare due volte per visualizzare i menù.

TM

64-bit / XP / XP 64-bit. Il CD di supporto a cor-

Italiano

54

ASRock H61 Pro BTC Motherboard

1. Introducción

Gracias por su compra de ASRock H61 Pro BTC placa madre, una placa de con-

anza producida bajo el control de calidad estricto y persistente. La placa madre
provee realización excelente con un diseño robusto conforme al compromiso de

calidad y resistencia de ASRock.

Esta Guía rápida de instalación contiene una introducción a la placa base y una
guía de instalación paso a paso. Puede encontrar una información más detallada
sobre la placa base en el manual de usuario incluido en el CD de soporte.

Porque las especicaciones de la placa madre y el software de BIOS
podrían ser actualizados, el contenido de este manual puede ser cambiado
sin aviso. En caso de cualquier modicación de este manual, la versión
actualizada estará disponible en el website de ASRock sin previo aviso.
También encontrará las listas de las últimas tarjetas VGA y CPU soportadas
en la página web de ASRock.

Website de ASRock http://www.asrock.com
Si necesita asistencia técnica en relación con esta placa base, visite

nuestra página web con el número de modelo especíco de su placa.

www.asrock.com/support/index.asp

1.1 Contenido de la caja

Placa base ASRock H61 Pro BTC (Factor forma ATX)

Guía de instalación rápida de ASRock H61 Pro BTC
CD de soporte de ASRock H61 Pro BTC

Dos cables de datos Serial ATA (SATA) (Opcional)

Una protección I/O

ASRock le recuerda...

Para mejorar el rendimiento en Windows® 8 / 8 64 bits / 7 / 7 64 bits / Vis-

TM

ta

/ VistaTM 64 bits, es recomendable establecer la opción del BIOS de
la conguración de almacenamiento en el modo AHCI. Para obtener de­talles sobre la conguración del BIOS, consulte el “Manual del usuario”
que se encuentra en nuestro CD de soporte.

ASRock H61 Pro BTC Motherboard

Español

55

Español

1.2 Especicación

Plataforma - Factor forma ATX

- Todo diseño de Capacitor Sólido
Procesador - Admite procesadores Intel® CoreTM i7 / i5 / i3 / Xeon® /

Pentium® / Celeron® de la 3ª y 2ª generación en el paquete

LGA1155

- Admite la tecnología Intel® Turbo Boost 2.0 Technology

- Admite procesador desbloqueado de la serie K
Chipset - Intel® H61

- Admite las tecnologías Intel® Rapid Start y Smart Connect
Memoria - Soporte de Tecnología de Memoria de Doble Canal

- 2 x DDR3 DIMM slots

- Apoya DDR3 1600/1333/1066 non-ECC, memoria de
un-buffered (DDR3 1600 con CPU Intel® Ivy Bridge,
DDR3 1333 con CPU Intel® Sandy Bridge)

- Máxima capacidad de la memoria del sistema: 16GB

- Compatible con Intel® Extreme Memory Prole (XMP)1.3/1.2

con la CPU Intel® Ivy Bridge
Ranuras de - 1 x ranura PCI Express 3.0 x16 (PCIE2 @ modo x16)

Expansión * PCIE 3.0 solamente se admite con una CPU Intel® Ivy
Bridge. Con una CPU Intel® Sandy Bridge, solamente
admite PCIE 2.0.

- 5 x ranura PCI Express 2.0 x1
VGA OnBoard * Los efectos visuales incorporados con grácos de alta
denición Intel® y las salidas VGA sólo se soportan con
procesadores con GPU integrada.

- Admite Intel® HD Graphics Built-in Visuals: Intel® Quick Sync
Video 2.0, Intel® InTruTM 3D, Intel® Clear Video HD

Technology, Intel® InsiderTM, Intel® HD Graphics 2500/4000
con la CPU Intel® Ivy Bridge

- Admite Intel® HD Graphics Built-in Visuals: Intel® Quick Sync
Video, Intel® InTruTM 3D, Intel® Clear Video HD Technology,
Intel® HD Graphics 2000/3000 e Intel® Advanced Vector
Extensions (AVX) con la CPU Intel® Sandy Bridge

- Pixel Shader 5.0, DirectX 11 con CPU Intel® Ivy Bridge, Pixel
Shader 4.1, DirectX 10.1 con CPU Intel® Sandy Bridge

- 1760MB de Memoria máxima compartida con la CPU
Intel® Ivy Bridge. 1759MB de Memoria máxima compartida
con la CPU Intel® Sandy Bridge.

- Salida de VGA dual: apoya los puertos de HDMI y de D-Sub

56

ASRock H61 Pro BTC Motherboard

por los reguladores independientes de la exhibición

- Admite HDMI con una resolución máxima de 1920x1200 a
60 Hz

- Admite D-Sub con una resolución máxima de 2048x1536 a
75 Hz

- Admite Sincronización automática entre audio y vídeo, Deep
Color (12 bpc), xvYCC y HBR (audio de alta tasa de bits)
con HDMI (se necesita un monitor compatible con HDMI)

- Admite la función HDCP con puertos HDMI

- Apoya la reproducción de Blu-rayo de 1080p (BD) / HD-DVD
con puertos HDMI

Audio - Sonido HD de 5.1 Canales (Códec de sonido VIA® VT1705)
LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Soporta Wake-On-LAN

- Admite detección de conexión de cable LAN

- Compatible con Ethernet 802.3az de bajo consumo

energético

- Compatible con PXE

Entrada/Salida - 1 x puerto de ratón PS/2
de Panel - 1 x puerto de teclado PS/2
Trasero - 1 x puerto D-Sub

- 1 x puerto HDMI

- 6 x puertos USB 2.0 predeterminados

- 1 x Puerto LAN RJ-45 con LED (LED de ACCIÓN/ENLACE y
LED de VELOCIDAD)

- Conexión de audio: Entrada de línea / Altavoz frontal /
Micrófono

Interfaz de - 4 x conexiones SATA2, admiten una velocidad de
almacenamiento transferencia de datos de hasta 3,0Gb/s, soporta NCQ, AHCI

y “Conexión en caliente”
Conectores - 1 x Cabezal de Módulo Infrarrojos

- 1x En-tête de port COM

- 1 x Conector de ventilador de CPU (4-pin)

- 1 x Conector de ventilador de chasis (4-pin)

- 1 x Conector de ventilador de alimentacion (4-pin)

- 1 x 24-pin cabezal de alimentación ATX

- 1 x 8-pin conector de ATX 12V power

- 2 x Cabezal de alimentación SLI/XFire

- 1 x Conector de audio de panel frontal

- 2 x Cabezal USB 2.0 (admite 4 puertos USB 2.0 adicionales)

Español

ASRock H61 Pro BTC Motherboard

57

BIOS - 32Mb AMI BIOS legal UEFI AMI compatible con GUI

- Soporta “Plug and Play”

- ACPI 1.1 compliance wake up events

- Soporta “jumper free”

- Soporta SMBIOS 2.3.1

- Múltiple ajuste de IGPU, DRAM, PCH, CPU PLL, VTT,

VCCSA Voltage
CD de soport - Controladores, utilidades, software de antivirus (versión de
prueba), Google Chrome Browser y Toolbar

Monitor - Sensibilidad a la temperatura del procesador
Hardware - Sensibilidad a la temperatura de la placa madre

- Taquímetros de los ventiladores del procesador y del CPU /
chasis / alimentación

- Ventilador silencioso del procesador y el chasis (ajuste
automático de la velocidad del ventilador del chasis en
función de la temperatura del procesador)

- Control de ajuste de la velocidad del ventilador de la CPU /

chasis

- Monitor de Voltaje: +12V, +5V, +3.3V, Vcore

OS - En conformidad con Microsoft® Windows® 8 / 8 64 bits / 7 / 7

64 bits / VistaTM / VistaTM 64 bits / XP / XP 64 bits
Certicaciones - FCC, CE, WHQL

- Cumple con la directiva ErP/EuP (se requiere una fuente de
alimentación que cumpla con la directiva ErP/EuP)

* Para más información sobre los productos, por favor visite nuestro sitio web:

http://www.asrock.com

Español

58

ASRock H61 Pro BTC Motherboard

1.3 Setup de Jumpers

La ilustración muestra como los jumpers
son congurados. Cuando haya un jumper-

cap sobre los pins, se dice gue el jumper

está “Short”. No habiendo jumper cap sobre
los pins, el jumper está “Open”. La ilus­tración muesta un jumper de 3 pins cuyo
pin 1 y pin 2 están “Short”.

Jumper Setting

Limpiar CMOS

(CLRCMOS1, jumper de 3 pins)
(ver p.2, No. 9)

Nota:

CLRCMOS1 permite borrar los datos de la memoria CMOS. Para borrar los
parámetros del sistema y restablecer la conguración predeterminada de los mismos,
apague el equipo y desenchufe el cable de alimentación de la toma de corriente
eléctrica. Deje que transcurran 15 segundos y, después, utilice un puente
cortocircuitar los contactos 2 y 3 de CLRCMOS1 durante 5 segundos. No borre
la memoria CMOS justamente después de actualizar el BIOS. Si necesita borrar
la memoria CMOS justamente después de actualizar el BIOS, debe iniciar primero
el sistema y, a continuación, cerrarlo antes de llevar a cabo el borrado de
dicha memoria. Tenga en cuenta que la contraseña, la fecha, la hora, el perl
predeterminado del usuario, el GUID 1394 y la dirección MAC solamente se
borrará si la batería CMOS se quita.

Valor predetermi-

nado

Restablecimiento de

la CMOS

para

ASRock H61 Pro BTC Motherboard

Español

59

Español

1.4 Cabezales y Conectores en Placas

Los conectores y cabezales en placa NO son puentes. NO coloque
las cubiertas de los puentes sobre estos cabezales y conectores. El
colocar cubiertas de puentes sobre los conectores y cabezales provo­cará un daño permanente en la placa base.

Conexiones de serie ATAII Estas cuatro conexiones de

(SATA2_0: vea p.2, N. 12)

(SATA2_1: vea p.2, N. 15)

(SATA2_2: vea p.2, N. 11)

(SATA2_3: vea p.2, N. 14)

permite una velocidad de
transferencia de 3.0 Gb/s.

Cable de datos de Cualquier extremo del cable de

serie ATA (SATA) los datos de SATA puede ser

(Opcional)

conectado con el disco duro

de SATA / SATAII o el
conectador de SATAII en esta

placa base.

Cabezal USB 2.0 Además de seises puertos

(9-pin USB6_7)

(vea p.2, N. 18)

USB 2.0 predeterminados en el

panel de E/S, hay dos bases

de conexiones USB 2.0 en
esta placa base. Cada una de

estas bases de conexiones

(9-pin USB8_9)

(vea p.2, N. 17)

admite dos puertos USB 2.0.

Cabezal de Módulo Infrarrojos Este cabezal soporta un

(5-pin IR1)

módulo infrarrojos de

(vea p.2, N. 13)

transmisión y recepción

wireless opcional.

serie ATAII (SATAII) admiten

SATA2_0

SATA2_2

cables SATA para dispositivos
de almacenamiento internos.

La interfaz SATAII actual

SATA2_1

1

USB _PWR

P-9

P-8

USB _PWR

P+9

P+8

SATA2_3

GND

DUM MY

GND

1

GND

PRE SENC E#

MIC 2_R

MIC 2_L

MIC _RET

J_S ENSE

OUT 2_R

OUT _RET

OUT 2_L

Conector de audio de Este es una interface para
panel frontal cable de audio de panel frontal

(9-pin HD_AUDIO1)

(vea p.2, N. 20)

que permite conexión y control

conveniente de apparatos de

Audio.

60

ASRock H61 Pro BTC Motherboard

1. El Audio de Alta Denición soporta la detección de conector, pero
el cable de panel en el chasis debe soportar HDA para operar

correctamente. Por favor, siga las instrucciones en nuestro manual y
en el manual de chasis para instalar su sistema.

2. Si utiliza el panel de sonido AC’97, instálelo en la cabecera de sonido

del panel frontal de la siguiente manera:

A. Conecte Mic_IN (MIC) a MIC2_L.
B. Conecte Audio_R (RIN) a OUT2_R y Audio_L (LIN) en OUT2_L.
C. Conecte Ground (GND) a Ground (GND).

D. MIC_RET y OUT_RET son sólo para el panel de sonido HD. No
necesitará conectarlos al panel de sonido AC’97.

Cabezal de panel de sistema Este cabezar acomoda varias

(9-pin PANEL1)

(vea p.2, N. 16)

Conecte el interruptor de alimentación, el interruptor de restablecimiento

y el indicador de estado del sistema situados en el chasis con esta

cabecera en función de las siguientes asignaciones de contacto. Preste
atención a los contactos positivos y negativos antes de conectar los

cables.

PWRBTN (interruptor de alimentación):

RESTABLECER (interruptor de restablecimiento):

PLED (LED de alimentación del sistema):

HDLED (LED de actividad del disco duro):

dunciones de panel frontal de

sistema.

Conecte el interruptor de encendido situado en el panel frontal del
chasis. Puede congurar la forma de apagar su sistema mediante el
interruptor de alimentación.

Conecte el interruptor de restablecimiento situado en el panel frontal del

chasis. Pulse el interruptor de restablecimiento para restablecer el
equipo si se bloquea y no se reinicia con normalidad.

Conecte el indicador de estado de alimentación situado en el panel

frontal del chasis. El LED se enciende cuando el sistema esté en
funcionamiento. El LED parpadea cuando el sistema se encuentre en

estado de suspensión S1. El LED se apaga cuando el sistema se
encuentre en estado de suspensión S3/S4 o se apaga (S5).

Conecte el LED de actividad de disco duro situado en el panel frontal

del chasis. El LED se enciende cuando el disco duro esté leyendo o
escribiendo datos.

Español

Es posible que el diseño del panel frontal varíe en función del chasis. Un
módulo del panel frontal consiste principalmente de interruptor de
alimentación, interruptor de restablecimiento, LED de alimentación, LED

ASRock H61 Pro BTC Motherboard

61

de actividad del disco duro, altavoz, etc. Al conectar el módulo del panel
frontal del chasis a esta cabecera, asegúrese de que las asignaciones

de cables y las asignaciones de contactos coincidan correctamente.

Cabezal del altavoz del chasis Conecte el altavoz del chasis a

(4-pin SPEAKER1)

(vea p.2, N. 10)

su cabezal.

Conectores de ventilador de chasis
y alimentación

(4-pin CHA_FAN1)

(vea p.2, N. 6)

(4-pin PWR_FAN1)

(vea p.2, N. 28)

Conector del ventilador Conecte el cable del ventilador
de la CPU de la CPU a este conector y

(4-pin CPU_FAN1)

(vea p.2, N. 2)

FAN_ SPEE D_CO NTRO L

CPU _FAN_ SPEE D

+12 V

haga coincidir el cable negro

con el conector de tierra.

GND

1 2 3 4

Por favor, conecte los cables del
ventilador a los conectores de
ventilador, haciendo coincidir el
cable negro con la patilla de
masa.

Aunque esta placa base proporciona compatibilidad para un ventilador

(silencioso) de procesador de 4 contactos, el ventilador de procesador
de 3 contactos seguirá funcionando correctamente incluso sin la función

de control de velocidad del ventilador. Si pretende enchufar el ventilador
de procesador de 3 contactos en el conector del ventilador de
procesador de esta placa base, conéctelo al contacto 1-3.

Contacto 1-3 conectado

Instalación del ventilador de 3 contactos

Cabezal de alimentación ATX Conecte la fuente de

(24-pin ATXPWR1)

(vea p.2, N. 5)

alimentación ATX a su cabezal.

12 124

Español

62

13

A pesar de que esta placa base incluye in conector

de alimentación ATX de 24 pins, ésta puede funcionar
incluso si utiliza una fuente de alimentación ATX de
20 pins tradicional. Para usar una fuente de
alimentación ATX de 20 pins, por favor, conecte su
fuente de alimentación usando los Pins 1 y 13.

Instalación de una Fuente de Alimentación ATX de 20 Pins

ASRock H61 Pro BTC Motherboard

12

1

24

13

Conector de ATX 12V power Tenga en cuenta que es

(8-pin ATX12V1)

(vea p.2, N. 3)

necesario conectar este

conector a una toma de

8 5

4 1

corriente con el enchufe ATX

12V, de modo que proporcione
suciente electricidad. De lo
contrario no se podrá encender.

Aunque esta placa base proporciona un conector de energía de 8-pin ATX 12V,
puede todavía trabajar si usted adopta un fuente tradicional de energía de 4-pin
ATX 12V. Para usar el fuente de energía de 4-pin ATX 12V, por favor conecte
su fuente de energía junto con Pin 1 y Pin 5.

8 5

Instalación de Fuente de Energía de 4-Pin ATX 12V

4 1

Cabezal del puerto COM Este cabezal del puerto COM

(9-pin COM1)

(vea p.2, N. 19)

Conector de alimentación SLI/XFire

(4-pin SLI/XFIRE_PWR1)
(vea p.2, N. 29)

se utiliza para admitir un

módulo de puerto COM.

Conecte este conector con un
conector de alimentación de
alimentación cuando haya tres
tarjetas grácas instaladas en

(4-pin SLI/XFIRE_PWR2)
(vea p.2, N. 27)

esta placa base.

ASRock H61 Pro BTC Motherboard

Español

63

2. BIOS Información

El Flash Memory de la placa madre deposita SETUP Utility. Durante el Power-Up
(POST) apriete <F2> o <Del> para entrar en la BIOS. Sí usted no oprime ninguna
tecla, el POST continúa con sus rutinas de prueba. Si usted desea entrar en la
BIOS después del POST, por favor reinicie el sistema apretando <Ctl> + <Alt> +
<Borrar>, o apretando el botón Reset en el panel del ordenador. Para información
detallada sobre como congurar la BIOS, por favor reérase al Manual del Usuario
(archivo PDF) contenido en el CD.

3. Información de Software Support CD

Esta placa-base soporta diversos tipos de sistema operativo Windows®: 8 / 8 64 bits

/ 7 / 7 64 bits / VistaTM / Vista
acompaña la placa-base trae todos los drivers y programas utilitarios para instalar y
congurar la placa-base. Para iniciar la instalación, ponga el CD en el lector de CD
y se desplegará el Menú Principal automáticamente si «AUTORUN» está habilitado

en su computadora.

Si el Menú Principal no aparece automáticamente, localice y doble-pulse en el ar­chivo “ASSETUP.EXE” para iniciar la instalación.

TM

64 bits / XP / XP 64 bits. El CD de instalación que

Español

64

ASRock H61 Pro BTC Motherboard

1. Введение

Благодарим вас за покупку материнской платы ASRock H61 Pro BTC надежной
материнской платы, изготовленной в соответствии с постоянно предъявляемыми ASRock
жесткими требованиями к качеству. Она обеспечивает превосходную производительность
и отличается отличной конструкцией, которые отражают приверженность ASRock качеству
и долговечности.
Данное руководство по быстрой установке включает вводную информацию о материнской
плате и пошаговые инструкции по ее установке. Более подробные сведения о плате
можно найти в руководстве пользователя на компакт-диске поддержки.

Спецификации материнской платы и программное обеспечение
BIOS иногда изменяются, поэтому содержание этого руководства
может обновляться без уведомления. В случае любых
модификаций руководства его новая версия будет размещена на
веб-сайте ASRock без специального уведомления. Кроме того,
самые свежие списки поддерживаемых модулей памяти и
процессоров можно найти на сайте ASRock.
Адрес веб-сайта ASRock http://www.asrock.com
При необходимости технической поддержки по вопросам данной
материнской платы посетите наш веб-сайт для получения
информации об используемой модели.

www.asrock.com/support/index.asp

1.1 Комплектность

Материнская плата ASRock H61 Pro BTC (форм-фактор ATX)
Руководство по быстрой установке ASRock H61 Pro BTC
Компакт-диск поддержки ASRock H61 Pro BTC
2 x кабель данных Serial ATA (SATA) (дополнительно)
1 x I/O Щит Группы ввода / вывода

ASRock напоминает...

Для обеспечения максимальной производительности ОС Windows®
8 / 8 64-bit / 7 / 7 64-bit / Vista
BIOS выбрать для параметра Storage Conguration (Конфигурация
запоминающего устройства) режим AHCI. Подробные сведения о
настройке BIOS см. в руководстве пользователя на прилагаемом
компакт-диске.

TM

/ VistaTM 64-bit рекомендуется в

ASRock H61 Pro BTC Motherboard

Русский

65

Русский

1.2 Спецификации

Платформа - форм-фактор ATX



- Весь Твердый Конденсаторный проект
Процессор - Поддержка процессора Intel® CoreTM i7 / i5 / i3 / Xeon® / Pentium® /
Celeron® 3-го и 2-го поколения с помощью разъема для процессоров
LGA 1155

- Поддержка технологии Intel® Turbo Boost 2.0

- Поддержка разблокированного ЦП серии K
Набор микросхем - Intel® H61

- Поддержка технологии Intel® Rapid Start Technology и Smart Connect

Technology
Память - Поддержка технологии Dual Channel DDR3 Memory Technology

- 2 x гнезда DDR3 DIMM

- Поддержите DDR3 1600/1333/1066 не- ECC, безбуферная память
(DDR3 1600 с процессором Intel® Ivy Bridge, DDR3 1333 с
процессором Intel® Sandy Bridge)

- Максимальный объем системной памяти: 16 ГБ

- поддержка профиля Intel® Extreme Memory Prole (XMP)1.3/1.2 с
помощью процессора Intel® Ivy Bridge

Гнезда - 1 x PCI Express 3.0 x16 (PCIE2 в режиме x16)
расширения * PCIE 3.0 поставляется только в комплекте с ЦП Intel® Ivy Bridge. В

комплекте с ЦП Intel® Sandy Bridge поставляется только модель
PCIE 2.0.

- 5 x PCI Express 2.0 x1
Графика * Встроенный видеоадаптер Intel® HD Graphics и выходы VGA
поддерживаются только с процессорами, оснащенными
интегрированным графическим процессором.

- Поддержка функций встроенных видеоадаптеров Intel® HD: Intel®
Quick Sync Video 2.0, Intel® InTruTM 3D, технологии Intel® Clear Video
HD, Intel® InsiderTM, Intel® HD Graphics 2500/4000 с помощью
процессора Intel® Ivy Bridge

- Поддержка функций встроенных видеоадаптеров Intel® HD: Intel®
Quick Sync Video, Intel® InTruTM 3D, технологии Intel® Clear Video HD,
Intel® HD Graphics 2000/3000, Intel® Advanced Vector Extensions (AVX)
с помощью процессора Intel® Sandy Bridge

- Pixel Shader 5.0, DirectX 11 с процессором Intel® Ivy Bridge, Pixel
Shader 4.1, DirectX 10.1 с процессором Intel® Sandy Bridge

- Макс. объем разделяемой памяти 1760Мб с помощью процессора
Intel® Ivy Bridge. Макс. объем разделяемой памяти 1759Мб с
помощью процессора Intel® Sandy Bridge.

- Двойственное VGA выходное устройство: поддерживает HDMI и
D-Sub порты через независимый контроллер дисплея

- Поддержка HDMI с максимальным разрешением до 1920х1200 @
60 Гц

- Поддержка D-Sub с максимальным разрешением до 2048х1536 @
75 Гц

66

ASRock H61 Pro BTC Motherboard

- Поддержка Auto Lip Sync, Deep Color (12 бит на цветовой канал),
xvYCC и HBR (High Bit Rate Audio) через HDMI (необходим
монитор с разъемом HDMI)

- Поддержка функции HDCP через разъемы HDMI

- Подержат Blu-луч 1080p (КОММУТАЦИОННАЯ ДОСКА) /
воспроизведение HD-DVD через разъемы HDMI

ЛВС - PCIE x 1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- поддержка Wake-On-LAN

- Поддержка определения кабеля ЛВС

- Поддержка энергосберегающего интерфейса Ethernet 802.3az

- Поддержка PXE

Разъемы ввода- - 1 x порт мыши PS/2
вывода на задней - 1 x порт клавиатуры PS/2
панели - 1 x D-Sub порт

- 1 x HDMI порт

- 6 x порта USB 2.0 на задней панели в стандартной конфигурации

- Разъем 1 x RJ-45 LAN с светодиодным индикатором (индикатор
ACT/LINK и индикатор SPEED)

- Соединитель звуковой подсистемы: линейный вход / передняя
колонка / микрофон
Интерфейсы - 4 x разъема SATA2 3,0 Гбит/с, поддержка функций NCQ, AHCI и

накопителей «горячего подключения»
Колодки и плате - 1 x Разъем порта печати

- 1 x Колодка COM

- 1 x соединитель CPU FAN (4-контактный)

- 1 x соединитель Chassis FAN (4-контактный)

- 1 x соединитель Power FAN (4-контактный)

- 1 x 24-контактный Колодка питания ATX

- 1 x 8-контактный Разъем ATX 12 В

- 2 x Разъем питания SLI/XFire

- 1 x Аудиоразъем передней панели

- 2 x Колодка USB 2.0 (одна колодка для поддержки 4
дополнительных портов USB 2.0
BIOS - 32Mb AMI UEFI Legal BIOS с поддержкой rpaфичеckoro интеpфeйca
поль зователя

- поддержка “Plug and Play”

- ACPI 1.1, включение по событиям

- поддержка режима настройки без перемычек

- поддержка SMBIOS 2.3.1

- центральный IGPU, DRAM, Мультирегулирование Напряжения
PCH, CPU PLL, VTT, VCCSA
Компактдиск - Драйверы, служебные программы, антивирусное программное

поддержки обеспечение (пробная версия), Google Chrome Browser и Toolbar

Русский

ASRock H61 Pro BTC Motherboard

67

Контроль - Датчики температуры процессора
оборудования - Датчики температуры корпуса

- Тахометры вентиляторов CPU/Chassis/Power FAN

- Бесшумный вентилятор ЦП/системного блока (возможность авто
матической настройки скорости вентилятора системного блока в
соответствии с температурой центрального процессора)

- Мультиконтроль скорости вентилятора ЦП/системного

- Контроль напряжения: +12V, +5V, +3.3V, Vcore
Операцион - Совместимость с Microsoft® Windows® 8 / 8 64-bit / 7 / 7 64-bit /
Vista
ные системы - FCC, CE, WHQL
Сертификаты - Совместимость с ErP/EuP Ready (требуется блок питания
совместимый с ErP/EuP)
* Для детальной информации продукта, пожалуйста посетите наш вебсайт:

http://www.asrock.com

TM

/ Поддержка 64-разрядной версии VistaTM / XP / XP 64-bit

Русский

68

ASRock H61 Pro BTC Motherboard

1.3 Установка перемычек

Конфигурация перемычек иллюстрируется
на рисунке. Когда перемычка надета на
контакты, они называются “замкнутыми”
(short). Если на контактах перемычки нет,
то они называются “разомкнутыми” (open).
На иллюстрации показана 3-контактная
перемычка, у которой контакты 1 и 2
замкнуты.

Перемычка Установка Описание

Очистка CMOS

(CLRCMOS1,
3-контактная перемычка)
(см. стр. 2, п. 9)

Стандартные Очистка CMOS

Примечание.

Контактная колодк а CLRCMOS1 позволяет очистить данн ые CMOS . Для
очистки данных и восстановления заводских системных параметров сначала
вы кл ючите компьютер и отсоедините сетевую вилку кабел я пи та ни я от
электророзетки. Выждите не менее 15 секунд и колпачковой перемычкой на 5
секунд перемкните штырьки 2 и 3 контактной колодки CLRCMOS1. Однако не
производите очистку CMOS непосредственно после обновления BIOS. Если
необходимо очистить CMOS сразу же после окончания обновления BIOS, то,
перед очисткой CMOS, необходимо сначала выполнить загрузку системы, а
затем завершить ее работу. Примите во внимание, что пароль, дата, время,
профиль пользователя по умолчанию, идентификатор 1394 GUID и MAC-адрес
будут очищены только тогда, когда будет извлечена из своего гнезда батарейка
CMOS.

Русский

ASRock H61 Pro BTC Motherboard

69

Русский

1.4 Колодки и разъемы на плате

Имеющиеся на плате колодки и разъемы НЕ ЯВЛЯЮТСЯ
контактами для перемычек. НЕ УСТАНАВЛИВАЙТЕ перемычки
на эти колодки и разъемы – это приведет к необратимому
повреждению материнской платы!

Разъемы Serial ATAII Четыре соединителя Serial ATAII

(SATA2_0, см. стр. 2, п. 12)
(SATA2_1, см. стр. 2, п. 15)
(SATA2_2, см. стр. 2, п. 11)
(SATA2_3, см. стр. 2, п. 14)

кабелей SATAII. В настоящее
время интерфейс SATA
допускает скорость передачи
данных до \ 3,0 Гбит/с.

Информационный Информационный кабель
кабель Serial ATA (SATA) интерфейса SATA / SATAII

(дополнительно)

не является направленным.
Любой из его соединителей может
быть подключен либо к жесткому
диску интерфейса SATAII
либо к материнской плате.

Колодка USB 2.0 Помимо шесть стандартных

(9-контактный USB6_7)
(см. стр. 2, п. 18)

вывода, на данной материнской
плате предусмотрено два
разъема USB 2.0. Каждый разъем
USB 2.0 поддерживает два порта
USB 2.0.

(9-контактный USB8_9)
(см. стр. 2, п. 17)

Колодка инфракрасного модуля Данная колодка позволяет

(5-контактный IR1)
(см. стр. 2, п. 13)

модуль беспроводного
инфракрасного
приемопередатчика.

предназначаются для

SATA2_0

SATA2_2

подключения внутренних
устройств хранения с

использованием интерфейсных

SATA2_1

SATA2_3

портов USB 2.0 на панели ввода-

USB _PWR

P-9

P+9

GND

DUM MY

1

P-8

USB _PWR

P+8

GND

подключить дополнительный

70

ASRock H61 Pro BTC Motherboard

Аудиоразъем передней Этот интерфейс предназначен
панели для присоединения

(9-контактный HD_AUDIO1)
(см. cтр. 2, п. 20)

обеспечивающего удобное

аудиокабеля передней панели,

подключение аудиоустройств и
управление ими.

1

GND

PRE SENC E#

MIC 2_R

MIC 2_L

MIC _RET

J_S ENSE

OUT 2_R

OUT _RET

OUT 2_L

1. Система High Denition Audio поддерживает функцию
автоматического обнаружения разъемов (Jack Sensing), однако
для ее правильной pаботы кабель панели в корпусе должен
поддерживать HDA. При сборке системы следуйте инструкциям,
приведенным в нашем руководстве и руководстве пользователя
для корпуса.

2. Если вы используете аудиопанель AC’97, подключите ее к колодке
аудиоинтерфейса передней панели следующим образом:
A. Подключите выводы Mic_IN (MIC) к контактам MIC2_L.
B. Подключите выводы Audio_R (RIN) к контактам OUT2_R, а
выводы Audio_L (LIN) к контактам OUT2_L.
C. Подключите выводы Ground (GND) к контактам Ground (GND).

D. Контакты MIC_RET и OUT_RET предназначены только для
аудиопанели HD. При использовании аудиопанели AC’97

подключать их не нужно.

Колодка системной панели Данная колодка обеспечивает

(9-контактный PANEL1)
(см. стр. 2, п. 16)

работу нескольких функций

передней панели системы.

Подключите к этому разъему кнопку питания, кнопку сброса
и индикатор состояния системы на корпусе в соответствии с
указанным ниже назначением контактов. При подключении кабелей
необходимо соблюдать полярность положительных и отрицательных
контактов.

PWRBTN (кнопка питания):

Подключите к этим контактам кнопку питания на передней панели
корпуса. Способ выключения системы с помощью кнопки питания
можно настроить.

RESET (кнопка сброса):

Подключите к этим контактам кнопку сброса на передней панели
корпуса. Нажмите кнопку сброса для перезагрузки компьютера, если
компьютер «завис» и нормальную перезагрузку выполнить не
удается.

ASRock H61 Pro BTC Motherboard

Русский

71

PLED (индикатор питания системы):

Подключите к этим контактам индикатор состояния питания на
передней панели корпуса. Этот индикатор светится, когда система
работает. Индикатор мигает, когда система находится в режиме
ожидания S1. Этот индикатор не светится, когда система находится
в режиме ожидания S3 или S4, либо выключена (S5).

HDLED (индикатор активности жесткого диска):

Подключите к этим контактам индикатор активности жесткого диска
на передней панели корпуса. Этот индикатор светится, когда
осуществляется считывание или запись данных на жестком диске.

Конструкция передней панели может различаться в зависимости от
корпуса. Модуль передней панели в основном состоит из кнопки
питания, кнопки сброса, индикатора питания, индикатора активности
жесткого диска, динамика и т.п. При подключении к этому разъему
модуля передней панели корпуса удостоверьтесь, что провода
подключаются к соответствующим контактам.

Колодка динамика корпуса Подключите к этой колодке

(4-контактный SPEAKER1)
(см. стр. 2, п. 10)

кабель от динамика на корпусе

компьютера.

Русский

Chassis и Power Fan-соединители

(4-контактный CHA_FAN1)
(см. стр. 2, п. 6)

Подключите кабели вентилятора
к соединителям и присоедините
черный шнур к штырю
заземления.

(4-контактный PWR_FAN1)
(см. стр. 2, п. 28)

Разъем вентилятора Подключите к этому разъему
процессора кабель вентилятора процессора

(4-контактный CPU_FAN1)
(см. стр. 2, п. 2)

соответствовал контакту земли.

FAN_ SPEE D_CO NTRO L

CPU _FAN_ SPEE D

так, чтобы черный провод

+12 V

GND

1 2 3 4

Данная материнская плата поддерживает вентиляторы процессора
с 4-контактным разъемом (функция тихого режима вентилятора),
однако вентиляторы с 3-контактным разъемом также будут успешно
работать, хотя функция управления скоростью вращения
вентилятора окажется недоступной. Если вы хотите подключить
вентилятор процессора с 3-контактным разъемом к разъему
вентилятора процессора на данной материнской плате, для этого
следует использовать контакты 1-3.

Контакты 1-3 подключены

Установка вентилятора с 3-контактным разъемом

72

ASRock H61 Pro BTC Motherboard

Колодка питания ATX Подключите к этой колодке

(24-контактный ATXPWR1)
(см. стр. 2, п. 5)

кабель питания ATX.

Несмотря на то, что эта материнская плата предусматр­ ивает 24-штыревой разъем питания ATX, работа будет

12 124

13

12

продолжаться, даже если адаптируется традиционный
20-штыревой разъем питания ATX. Для использования
20-штыревого разъема питания ATX вставьте источник
питания вместе со штекером 1 и штекером 13.

Установка 20-штыревого разъема питания ATX

1

24

13

Колодка питания 12V-ATX Обратите внимание, что к этому

(8-контактный ATX12V1)
(см. стр. 2, п. 3)

разъему необходимо

подключить вилку блока питания

ATX 12 В, чтобы обеспечить

8 5

4 1

достаточную мощность
электропитания. В противном
случае включение системы будет
невозможно.

Хотя эта объединительная плата обеспечивает ATX с 8 булавками 12V

соединитель власти, это может все еще работать, если Вы принимаете
традиционный ATX с 4-Pin 12V электропитание. Чтобы использовать
электропитание ATX с 4-Pin, пожалуйста включите ваше электропитание
наряду с Булавкой 1 и Прикрепите 5.

ATX С 4-Pin 12V Установка Электропитания

8 5

4 1

Колодка COM-порта Данная колодка COM-порта

(9-контактный COM1)
(см. стр. 2, п. 19)

Разъем питания SLI/XFire

(4-контактный SLI/XFIRE_PWR1)
(см. стр. 2, п. 29)

(4-контактный SLI/XFIRE_PWR2)
(см. стр. 2, п. 27)

позволяет подключить модуль

порта COM.

Этот разъем предназначен для
подключения разъема питания
разъем питания при установке на
материнскую плату три видеокарт.

Русский

ASRock H61 Pro BTC Motherboard

73

2. Информация о BIOS

Утилита настройки BIOS (BIOS Setup) хранится во флэш-памяти на материнской плате.
Чтобы войти в программу настройки BIOS Setup, при запуске компьютера нажмите <F2>
или <Del> во время самопроверки при включении питания (Power-On-Self-Test – POST).
Если этого не сделать, то процедуры тестирования POST будут продолжаться обычным
образом. Если вы захотите вызвать BIOS Setup уже после POST, перезапустите систему
с помощью клавиш <Ctrl> + <Alt> + <Delete> или нажатия кнопки сброса на корпусе
системы. Подробную информацию о программе BIOS Setup вы найдете в Руководстве
пользователя (в формате PDF) на компакт-диске поддержки.

3. Информация о компакт-диске
поддержки с программным
обеспечением

Данная материнская плата поддерживает различные операционные системы Microsoft®

Windows®: 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit. Поставляемый

вместе с ней компакт-диск поддержки содержит необходимые драйверы и полезные
утилиты, которые расширяют возможности материнской платы.
Чтобы начать работу с компакт-диском поддержки, вставьте его в дисковод CD-ROM.
Если в вашем компьютере включена функция автозапуска (AUTORUN), то на экране
автоматически появится главное меню компакт-диска (Main Menu). Если этого не
произошло, найдите в папке BIN на компакт-диске поддержки файл ASSETUP.EXE и
дважды щелкните на нем, чтобы открыть меню.

Русский

74

ASRock H61 Pro BTC Motherboard

1. Introdução

Gratos por comprar nossa placa–mãe H61 Pro BTC um produto conável feito com
ASRock um estrito controle de qualidade consistente. Com um excelente desem-

penho, essa placa é dotada de um projeto robusto que atende a ASRock de com­promisso com a qualidade e durabilidade.
Este Guia de Instalação Rápida apresenta a placa-mãe e o guia de instalação pas­so a passo. Mais informações detalhadas sobre a placa-mãe podem ser encontra-

das no manual do usuário do CD de suporte.

poderiam ser atualizados, o conteúdo deste manual pode ser
cambiado sem aviso. Em caso de qualquer modicação deste
manual, a versão atualizada estará disponível no website de ASRock

sem prévio aviso. Pode também encontrar as listas das mais recentes

placas VGA e das CPUs suportadas no site da web da ASRock.

Website de ASRock http://www.asrock.com
Se precisar de apoio técnico em relação a este placa-mãe, por favor

visite o nosso sítio da internet para informação especíca acerca do
modelo que está a utilizar.

www.asrock.com/support/index.asp

Porque as especicações da placa mãe e o software de BIOS

1.1 Este pacote contém

Placa-mãe ASRock H61 Pro BTC (Formato ATX)

Guia de instalação rápida da ASRock H61 Pro BTC
CD de suporte da placa ASRock H61 Pro BTC

Dois cabo de dados ATA Serial (SATA) (Opcional)

Uma proteção I/O

A ASRock recorda-lhe...

Para obter melhor desempenho em Windows® 8 / 8 64-bit / 7 / 7 64-bit /

VistaTM / VistaTM 64-bit, recomendamos que dena a opção Conguração
de Ar-mazenamento na BIOS para o modo AHCI. Para mais detalhes
acerca da conguração da BIOS consulte o “Manual de utilizador” no
nosso CD de suporte.

ASRock H61 Pro BTC Motherboard

Português

75

Português

1.2 Especicações

Plataforma - Formato ATX

- Design de condensadores banhados a ouro de alta qualidade
CPU - Suporta Intel® CoreTM i7 / i5 / i3 / Xeon® / Pentium® / Celeron®

de 3ª e 2ª geração no pacote LGA1155

- Suporta a tecnologia Intel® Turbo Boost 2.0

- Suporta K-Series desbloqueado CPU
Chipsets - Intel® H61

- Suporta a tecnologia Rapid Start da Intel® e a tecnologia
Smart Connect
Memória - Suporte à tecnologia de memória de duplo canal

- 2 x slots de DDR3 DIMM

- Suporte para memória não intermédia DDR3 1600/1333/1066,
não ECC (DDR3 1600 com Intel® Ivy Bridge CPU, DDR3 1333
com processadores Intel® Sandy Bridge CPU)

- Capacidade máxima de memória do sistema: 16GB

- Suporta Extreme Memory Prole (XMP)1.3/1.2 da Intel® com

CPU Ivy Bridge da Intel

Slots de - 1 x slot de PCI Express 3.0 x16 (modo PCIE2 @ x16)
Expansão * O modo PCIE 3.0 apenas é suportado com a CPU Ivy Bridge

da Intel® A CPU Sandy Bridge da Intel® apenas suporta o
modo PCIE 2.0.

- 5 x slot de PCI Express 2.0 x1
VGA integrado * As saídas Intel® HD Graphics Built-in Visuals e VGA são
suportadas apenas por processadores com GPU integrada.

- Suporta Intel® HD Graphics Embutido Visuals: Intel® Quick
Sync Video 2.0, Intel® Clear Video HD Technology, Intel®
InsiderTM, Intel® HD Graphics 2500/4000 com CPU Ivy Bridge
da Intel®

- Suporta Intel® HD Graphics Embutido Visuals: Intel® Quick
Sync Video, Intel® Clear Video HD Technology, Intel® HD
Graphics 2000/3000, Intel® Advanced Vector Extensions (AVX)
com CPU Sandy Bridge da Intel

- Pixel Shader 5.0, DirectX 11 com Intel® Ivy Bridge CPU, Pixel
Shader 4.1, DirectX 10.1 com processadores Intel® Sandy
Bridge CPU

- Memória partilhada máxima 1760MB com CPU Ivy Bridge da
Intel®. Memória partilhada máxima 1759MB com CPU Sandy
Bridge da Intel®.

- Porta de saída VGA dupla: suporta portas HDMI e D-Sub

®

®

76

ASRock H61 Pro BTC Motherboard

através de controladores de visualização independentes

- Suporta HDMI Tecnologia com resolução máxima até
1920x1200 @ 60Hz

- Suporta D-Sub com resolução máxima até 2048x1536 @
75Hz

- Suporta as funções Auto Lip Sync (Sincronização automática
do som), Deep Color (Profundidade da cor) (12bpc), xvYCC e
HBR (áudio de taxa de bits elevada) com HDMI (é necessário
um monitor compatível com a norma HDMI)

- Suportar HDCP função com HDMI porta

- Suportar 1080p Blu-ray (BD) / HD-DVD playback com HDMI

porta
Áudio - Áudio de alta denição de canal 5.1

(Codec de áudio VIA® VT1705)

LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Suporta Wake-On-LAN

- Suporta Detecção de cabo LAN

- Suporta Ethernet com Eciência Energética 802.3az

- Suporta PXE
Entrada/Saída - 1 x porta para mouse PS/2
pelo painel - 1 x porta para teclado PS/2
traseiro - 1 x porta D-Sub

- 1 x porta HDMI

- 6 x portas USB 2.0 padrão

- 1 x porta LAN RJ-45 com LED (LED ACT/LIG e LED
VELOCIDADE)

- Áudio Jack: saída / entrada de linha / microfone + porta

de jogos

Interface de - 4 x conectores SATA2, suporte a taxa de transferência
Armazenamento de dados de até 3,0 Gb/s, suporte NCQ, AHCI e “conexão

a quente”
Conectores - 1 x Conector do módulo de infravermelho

- 1 x conector da porta COM

- 1 x Conector do ventilador da CPU (4 pinos)

- 1 x Conector do ventilador da chassis (4 pinos)

- 1 x Conector do ventilador da energia (4 pinos)

- 1 x Conector de força do ATX de 24 pinos

- 1 x Conector ATX 12 V de 8 pinos

- 2 x Conector de alimentação SLI/XFire

- 1 x Conector Áudio do painel frontal

- 2 x cabezal USB 2.0 (suporta 4 portas USB 2.0)

ASRock H61 Pro BTC Motherboard

Português

77

BIOS - 32Mb BIOS UEFI ocial da AMI com suporte para GUI

- Suporta dispositivos “Plug and Play”

- ACPI 1.1 atendendo a eventos de “wake up”

- Suporta dispositivos sem jumper

- Suporte para SMBIOS 2.3.1

- IGPU, DRAM, PCH, CPU PLL, VTT, VCCSA Voltage

Multi-adjustment

CD de suporte - Controladores, utilitários, software antivírus (Experimentacao
Versao), Navegador Google Chrome e Barra de Ferramentas

Monitor do HW - Sensores de temperature do procesador

- Medição de temperatura da placa-mãe

- Tacômetros de ventilador do Processador/chassis/energia

- Ventoinha silenciosa para a CPU/chassis (Permitir velocidade
Chassis Auto-Ajuste de temperatura da CPU)

- CPU/Chassis Fan Controle Multi-Velocidade

- Monitoramento de voltagem : +12 V, +5 V, +3.3 V, Vcore

Sistema - Microsoft® Windows® 8 / 8 de 64 bits / 7 / 7 de 64 bits / Vista
Operacional

/ Vista

TM

de 64 bits / XP / XP de 64 bits

Certicações - FCC, CE, WHQL

- “ErP/EuP Ready” (é necessária alimentação eléctrica “ErP/
EuP Ready”)

* Para informações mais detalhadas por favor visite o nosso sítio Web:

http://www.asrock.com

TM

Português

78

ASRock H61 Pro BTC Motherboard

1.3 Conguração dos Jumpers

A ilustração mostra como os jumpers são

congurados. Quando há uma capa de
jumpers sobre os pinos, diz–se que o jump­er está “curto”. Não havendo capa sobre os
pinos, o jumper está “aberto”. A ilustração

mostra um jumper de 3 pinos em que os

pinos 1 e 2 están “curtos” quando a capa
de jumper estiver colocada sobre esses 2

pinos.

Jumper Conguração

Restaurar CMOS

(CLRCMOS1, jumper de 3 pinos)
(veja a folha 2, No. 9)

Nota: CLRCMOS1 permite você limpar os dados em CMOS. Os dados em CMOS

incluem informações da conguração do sistema como: por exemplo a senha
do sistema, data, tempo, e os parámetros da conguração do sistema. Para
limpar e recongurar os parámetros do sistema a conguração inicial da fá­brica, por favor desligue o cabo de força, ponha em curto–circuito os pin 2 e
pin 3 de CLRCMOS1 por mais de 5 segundos para limpar o CMOS usando

um jumper. Por favor lembrese de remover o jumper depois de limpar o

COMS. Se precisar limpar o CMOS ao concluir a atualização do BIOS, de­verá reiniciar o sistema primeiro e, em seguida, desligá-lo antes de executar
a ação de limpeza o CMOS.

Conguração-padrão Limpar o CMOS

ASRock H61 Pro BTC Motherboard

Português

79

Português

1.4 Conectores

Os conectores NÃO SÃO jumpers. NÃO coloque capas de jumper
sobre estes conectores. A colocação de pontos de jumper sobre os

conectores causará danos irreversíveis à placa-mãe.

Conector Figura Descrição

Conectores ATAII Serial Estes quatro conectores Serial

(SATA2_0: veja a folha 2, No. 12)

(SATA2_1: veja a folha 2, No. 15)

(SATA2_2: veja a folha 2, No. 11)

(SATA2_3: veja a folha 2, No. 14)

SATA2_0

ATA (SATAII) suportam
unidades de disco rígido SATA
ou SATAII como dispositivos de

SATA2_1

armazenamento internos. A

atual interface SATAII permite

uma taxa de transferência de
dados de até 3.0 Gb/s.

Cabo de dados Tanto a saída do cabo de Serial

ATA (SATA) dados SATA pode ser

(opcional)

conectado ao disco rígido
SATA / SATAII quanto o
conector SATAII na placa mãe.

Cabezal USB 2.0 Além das seis portas USB

(USB6_7 de 9 pinos)

(veja a folha 2, No. 18)

2.0 por defeito no painel de
entrada/saída, há dois

ligações USB 2.0 nesta placa­ mãe. Cada ligação USB 2.0
pode suportar dois portas USB

1

USB _PWR

P-9

P-8

USB _PWR

(USB4_5 de 9 pinos)

(veja a folha 2, No. 17)

2.0.

Conector do módulo Este conector suporta um
de infravermelho módulo de infravermelho para

(IR1 de 5 pinos)

(veja a folha 2, No. 13)

transmissão e recepção sem

o, opcional.

P+9

P+8

GND

GND

SATA2_2

SATA2_3

DUM MY

80

ASRock H61 Pro BTC Motherboard

Conector Áudio do painel Esta é uma interface para o
frontal cabo de áudio no painel frontal,

(HD_AUDIO1 de 9 pinos)

(veja a folha 2, No. 20)

que permite uma conexão e

controle convenientes dos

dispositivos de áudio.

1

GND

PRE SENC E#

MIC 2_R

MIC 2_L

MIC _RET

J_S ENSE

OUT 2_R

OUT _RET

OUT 2_L

1. Áudio de elevada denição que suporta a sensibilidade da tomada,
mas o o do painel existente no chassis tem de suportar HDA para

funcionar correctamente. Siga s instruções que aparecem no manual
e no manual do chassis para instalar o sistema.

2. Se utilizar o painel de áudio AC’97, instale-o no cabeçalho de áudio
do painel frontal, como a gura abaixo mostra:
A. Ligue o Mic_IN (MIC) ao MIC2_L.
B. Ligue o Audio_R (RIN) ao OUT2_R e o Audio_L (LIN) ao OUT2_L.
C. Ligue o Ground (GND) ao Ground (GND).
D. MIC_RET e OUT_RET são apenas para o painel de áudio HD. Não
necessita de os ligar para o painel de áudio AC’97.

Conector do painel do sistema Este conector acomoda várias

(PANEL1 de 9 pinos)

(veja a folha 2, No. 16)

funções do painel frontal do

sistema.

Ligue o botão de alimentação, o botão de reposição e o indicador do

estado do sistema no chassis a este conector de acordo com a descrição
abaixo. Tenha em atenção os pinos positivos e negativos antes de ligar os
cabos.

PWRBTN (Botão de alimentação):
Ligue ao botão de alimentação no painel frontal do chassis. Pode congu-

rar a forma para desligar o seu sistema através do botão de alimentação.

RESET (Botão de reposição):

Ligue ao botão de reposição no painel frontal do chassis. Prima o botão

de reposição para reiniciar o computador caso este bloqueie e não seja

possível reiniciar normalmente.

PLED (LED de alimentação do sistema):
Ligue ao indicador do estado da alimentação no painel frontal do chassis.

O LED cará acesso quando o sistema estiver em funcionamento. O LED
cará intermitente quando o sistema estiver no estado de suspensão S1.
O LED cará desligado quando o sistema estiver nos estados de suspen­são S3/S4 ou desligado (S5).

ASRock H61 Pro BTC Motherboard

Português

81

HDLED (LED de actividade do disco rígido):

Ligue ao LED de actividade do disco rígido no painel frontal do chassis. O

LED cará acesso quando o disco rígido estiver a ler ou a escrever dados.

O design do painel frontal poderá variar dependendo do chassis. Um

módulo de painel frontal consiste principalmente em um botão de alimen-

tação, um botão de reposição, um LED de alimentação, um LED de acti-

vidade do disco rígido, um altifalante, etc. Ao ligar o seu módulo de painel
frontal do chassis a este conector, certique-se que os os e os pinos têm

uma correspondência exacta.

Conector do alto-falante do chassi Ligue o alto-falante do chassi

(SPEAKER1 de 4 pinos)

(veja a folha 2, No. 10)

neste conector.

Conector do ventilador do chassis/energia Ligue o cabo do ventilador

(CHA_FAN1 de 4 pinos)

(veja a folha 2, No. 6)

neste conector, coincidindo o o

preto com o pino de aterramen

to.

(PWR_FAN1 de 4 pinos)
(veja a folha 2, No. 28)

Português

82

Conector do ventilador da Ligue o cabo do ventilador da
CPU CPU, coincidindo o o preto

(CPU_FAN1 de 4 pinos)

(veja a folha 2, No. 2)

com o pino de aterramento.

FAN_ SPEE D_CO NTRO L

CPU _FAN_ SPEE D

+12 V

GND

1 2 3 4

Apesar de esta placa-mãe possuir 4 apoios para uma ventoinha de
CPU (Ventoinha silenciosa), uma ventoinha de 3 pinos para CPU poderá

funcionar mesmo sem a função de controlo de velocidade da ventoinha.

Se pretender ligar uma ventoinha de 3 pinos para CPU ao conector de
ventoinha do CPU nesta placa-mãe, por favor, ligue-a aos pinos 1-3.

Pinos 1-3 ligados

Instalação de Ventoinha de 3 pinos

ASRock H61 Pro BTC Motherboard

Conector de força do ATX Ligue a fonte de alimentação

(ATXPWR1 de 24 pinos)

(veja a folha 2, No. 5)

Embora esta placa-mãe providencie um conector de

energia ATX de 24 pinos, pode apesar disso funcionar

ATX neste conector.

12 124

13

12

24

com a adapta-ção de uma fonte de energia tradicional

de 20 pinos. Para usar a fonte de alimentação de 29

pinos, por favor ligue a sua fonte de alimentação com
o Pino 1 e o Pino 13.

Instalação da Fonte de alimentação ATX de 20 Pinos

1

13

Conector de força do ATX 12V Ligue a fonte de alimentação

(ATX12V1 de 8 pinos)

(veja a folha 2, No. 3)

ATX 12V neste conector.

8 5

4 1

Embora esta placa-mãe providencie um conector de energia ATX 12V

de 8 pinos, pode apesar disso funcionar com a adapta-ção de uma fonte

de energia tradicional de 4 pinos. Para usar a fonte de alimentação de 4
pinos, por favor ligue a sua fonte de alimentação com o Pino 1 e o Pino 5.

8 5

Conector da porta COM

(COM1 de 9 pinos)

(veja a folha 2, No. 19)

suportar um módulo de porta

COM.

Instalação da Fonte de alimentação ATX 12V de 4 Pinos

Este conector é usado para

4 1

Conector de alimentação SLI/XFire Ligue este conector a um

(SLI/XFIRE_PWR1 de 4 pinos)

(veja a folha 2, No. 29)

conector de alimentação do

alimentação quando existirem

três placas grácas instaladas

(SLI/XFIRE_PWR2 de 4 pinos)

(veja a folha 2, No. 27)

nesta placa principal.

Português

ASRock H61 Pro BTC Motherboard

83

2. Informações da BIOS

O Utilitário de Conguração do BIOS está armazenado no chip FWH do BIOS. Ao
iniciar o computador, pressione <F2> ou <Del> durante o Autoteste de iniciação
(POST) para acessar o Utilitário de Conguração do BIOS; caso contrário, o POST
continuará com as rotinas de teste. Se desejar acessar o Utilitário de Conguração
do BIOS depois do POST, reinicie o sistema pressionando <Ctl> + <Alt> + <Del>,
ou pressionando o botão de reinício no chassi do sistema. Para as informações de­talhadas sobre o Utilitário de Conguração do BIOS, consulte o Manual do Usuário
(arquivo PDF) no CD de suporte.

3. Informações do CD de Suporte

Esta placa Mãe suporta vários sistemas operacionais: Microsoft® Windows®: 8 / 8
de 64 bits / 7 / 7 de 64 bits / VistaTM / VistaTM de 64 bits / XP / XP de 64 bits. O CD
de instalação que acompanha a placa Mãe contem: drivers e utilitários necessários
para um melhor desempenho da placa Mãe. Para começar a usar o CD de insta­lação, introduza o CD na leitora de CD-ROM do computador. Automaticamente
iniciará o menu principal, casa o AUTORUN esteja ativado. Se o menu principal não
aparecer automaticamente, explore o CD e execute o “ASSETUP.EXE” localizado
na pasta BIN.

Português

84

ASRock H61 Pro BTC Motherboard

1. Giriş

ASRock’ın kesintisiz titiz kalite denetimi altında üretilen güvenilir bir anakart olan
ASRock H61 Pro BTC anakartını satın aldığınız için teşekkür ederiz. ASRock’ın
kalite ve dayanıklılık konusundaki kararlılığına uygun güçlü tasarımıyla mükemmel

bir performans sunar.

Bu Hızlı Takma Kılavuzu anakarta giriş ve adım adım takma kılavuzu içerir. Anakart
hakkında daha ayrıntılı bilgiyi Destek CD’sinde sunulan kullanıcı kılavuzunda bula­bilirsiniz.

Anakart özellikleri ve BIOS yazılımı güncelleştirilebileceğinden bu kılavuzun içeriği
önceden haber verilmeksizin değişebilir. Bu belgede değişiklik yapılması durumun

-da, güncelleştirilmiş sürüm ayrıca haber verilmeksizin ASRock web sitesinde
sunulur. En son VGA kartlarını ve CPU destek listelerini de ASRock web sitesinde
bulabilirsiniz. ASRock web sitesi http://www.asrock.com

Bu anakartla ilgili teknik desteğe ihtiyacınız olursa, kullandığınız modele özel bilgiler
için lütfen web sitemizi ziyaret edin.

www.asrock.com/support/index.asp

1.1 Paket İçindekiler

ASRock H61 Pro BTC Anakart (ATX Form Faktörü)
ASRock H61 Pro BTC Hızlı Takma Kılavuzu
ASRock H61 Pro BTC Destek CD’si

2 x Seri ATA (SATA) Veri Kablosu (İsteğe Bağlı)
1 x G/Ç Panel Kalkanı

ASRock Size Şunu Hatırlatır...

Windows® 8 / 8 64-bit / 7 / 7 64-bit / Vista

performans elde etmek için, Depolama Konfigürasyonundaki BIOS
se çe ne ği ni AH CI mod un a ayarlamanız tavsiye edilir. BIOS ayarı
için, ayrıntıları öğrenmek üzere lütfen destek CD'mizdeki "Kullanıcı
Kılavuzu"na bakın.

ASRock H61 Pro BTC Motherboard

TM

/ VistaTM 64-bit ile daha iyi

Türkçe

85

Türkçe

1.2 Özellikler



Platform - ATX Form Faktörü

- Tüm Katı Kapasitör tasarımı

CPU - LGA1155 Paketi’deki 3. ve 2. Nesil Intel® CoreTM i7 / i5 / i3 /
Xeon® / Pentium® / Celeron®’yi destekler

- Intel® Turbo Boost 2.0 Teknolojisini destekler

- K-Serisi kilidi kaldırılmış işlemciyi destekler
Yonga seti - Intel® H61

- Intel® Rapid Start Teknolojisini ve Smart Connect Teknolojisi’ni

destekler
Bellek - Çift Kanallı DDR3 Belleği Teknolojisi

- 2 x DDR3 DIMM yuva

- DDR3 1600/1333/1066 ECC olmayan, ara belleksiz bellek
(Intel® Ivy Bridge işlemciye sahip DDR3 1600, Intel® Sandy
Bridge işlemciye sahip DDR3 1333)

- Sistem belleğinin maks. kapasitesi: 16 GB

- Intel® Ivy Bridge İşlemci ile Intel® Extreme Bellek Prolini
(XMP)1.3/1.2 destekler
Genişletme - 1 x PCI Express 3.0 x16 yuva (PCIE2 @ x16 modu)
Yuvası * PCIE 3.0, sadece Intel® Ivy Köprü İşlemcisiyle desteklenir.
Intel® Sandy Köprü İşlemciyle, sadece PCIE 2.0'ı

destekler.

- 5 x PCI Express 2.0 x1 yuva
Grakler * Intel® HD Grak Yerleşik Görselleri ve VGA çıkışları, yalnızca
GPU entegre işlemciler tarafından desteklenmektedir.

- Intel® Ivy Bridge İşlemci ile Intel® HD Graphics Dahili
Görselleri: Intel® Hızlı Eşitleme Videosu 2.0, Intel® InTruTM 3D,
Intel® Clear Video HD Teknolojisi, Intel® InsiderTM, Intel® HD
Graphics 2500/4000

- Intel® Sandy Bridge İşlemci ile Intel® HD Graphics Dahili
Görselleri: Intel® Hızlı Eşitleme Videosu, Intel® InTruTM 3D,
Intel® Clear Video HD Teknolojisi, Intel® HD Graphics
2000/3000, Intel® Gelişmiş Vektör Uzantıları (AVX)

- Pixel Shader 5.0, Intel® Ivy Bridge işlemciye sahip DirectX 11.
Pixel Shader 4.1,Intel® Sandy Bridge işlemciye sahip DirectX

10.1

- Intel® Ivy Bridge İşlemci ile Maks. paylaюэlan bellek 1760 MB.
Intel® Sandy Bridge İşlemci ile Maks. paylaюэlan bellek 1759

MB.

- Çift VGA Çıkış: desteği HDMI ve bağımsız görüntü

86

ASRock H61 Pro BTC Motherboard

denetleyiciler tarafından D-Sub bağlantı noktaları

- 60Hz’de 1920x1200’e kadar maks. зцzьnьrlьkle HDMI

Teknolojisini destekler

- 75Hz’de 2048x1536’ya kadar maks. зцzьnьrlьkle D-Sub’э

destekler

- Auto Lip Sync, Deep Color (12bpc), HDMI ile xvYCC ve
HBR’yi (Yьksek Bit Hэzlэ Ses) destekler (Uyumlu HDMI

monitцr gerekir)

- HDMI portlarэyla HDCP iюlevini destekler

- HDMI portlarэyla Tam HD 1080p Blu-ray (BD) /
HD-DVD oynatэmэnэ destekler

Ses - (VIA® VT1705 Ses Codec’i) 5,1 Kanal HD Ses
LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/sn

- Realtek RTL8111E

- LAN’da Uyan özelliğini destekler

- LAN Kablo Algılama’yı destekler

- Enerji Verimli Ethernet 802.3az desteği

- PXE’yi destekler
Arka Panel - 1 x PS/2 Fare Portu
G/З - 1 x PS/2 Klavye Portu

- 1 x D-Sub Portu

- 1 x HDMI Portu

- 6 x Kullanэma Hazэr USB 2.0 Portu

- 1 x RJ-45 LAN Portu, LED’li (AKT/LЭNK LED’i ve HIZ LED’i)

- HD Ses Jakı: Hat Girişi/Ön Hoparlör/Mikrofon

Depolama Ara - 4 x SATA2 3,0Gb/sn, donanım NCQ, AHCI ve “Sistem Açıkken
yüzü Bileşen Takma” işlevlerini
Konektör - 1 x KÖ şi

- 1 x COM portu şi

- 1 x Conector do ventilador da CPU (4 pinos)

- 1 x Conector do ventilador da chassis (4 pinos)

- 1 x Conector do ventilador da energia (4 pinos)

- 1 x 24 pin ATX güç konektörü

- 1 x 8 pin 12V güç konektörü

- 2 x SLI/XFire güç konektörü

- 1 x Ön panel ses konektörü

- 2 x USB 2.0 ş (4 USB 2.0 portu destekler)
BIOS Özelliği - 32 Mb GUI destekli AMI UEFI Geçerli BIOS

- “Tak Çalıştır”ı destekler

- ACPI 1.1 Uyumlu Uyandırma Olayları

- Jumpersız ayarlamayı destekler

Türkçe

ASRock H61 Pro BTC Motherboard

87

- AMBIOS 2.3.1 Desteği

- IGPU, DRAM, PCH, CPU PLL, VTT, VCCSA Voltaj Çoklu ayarı
Destek CD’si - Sürücüler, Yardımcı Programlar, AntiVirüs Yazılımı (Deneme
Sürümü), Google Chrome Browser ve Toolbar

Donanım - CPU Sıcaklık Duyarlılığı
Monitör - Kasa Sıcaklık Duyarlılığı

- CPU/Kasa/Güç Fan Takometresi

- İşlemci/Kasa Sessiz Fanı (Kasa Fan Hızı’nın İşlemci sıcaklığı
ile Otomatik Ayar’ına izin verir)

- CPU/Kasa Fan Çoklu-Hız Kontrolü

- Voltaj İzleme: +12V, +5V, +3,3V, CPU Vcore

İS - Microsoft® Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM

64-bit / XP / XP 64-bit uyumlu
Sertikalar - FCC, CE, WHQL

- ErP/EuP Hazır (ErP/EuP hazır güç kaynağı gerekli)

* Ayrıntılı ürün bilgileri için lütfen web sitemizi ziyaret edin: http://www.asrock.com

Türkçe

88

ASRock H61 Pro BTC Motherboard

1.3 Jumper'ların Ayarı

Şekilde jumper'ların nasıl ayarlandıkları
gösterilmektedir. Jumper kapağı pinler üzerine
yerleştirildiğinde jumper "Kapalı" dır. Jumper
kapağı pinler üzerindeyken jumper "Açık" tır.
Şekilde pin1 ve pin2'si "Kapalı" olan jumper
kapağı bu 2 pine yerleştirilmiş 3-pinli jumper

gösterilmektedir.

Jumper Ayar

CMOS’u temizleme

(CLRCMOS1, 3-pinli jumper)
(bkz. s.2 No. 9)

Not:

CLRCMOS1, CMOS’daki verilerinizi temizlemenize olanak sağlar. Sistem
parametrelerini temizlemek ve varsayılan ayara sıfırlamak için lütfen bilgisayarı
kapatın ve güç kablosunun şini güç kaynağından çekin. 15 saniye bekledikten
sonra, pin2 ve pin3‘ü CLRCMOS1’de 5 saniye kısaltmak için bir atlatıcı şapkası
kullanın. Ancak, BIOS’u güncelledikten hemen sonra lütfen CMOS’u temizlemeyin.
BIOS’u güncellemeyi tamamladığınızda CMOS’u temizlemeniz gerekirse,
ilk ol arak siste mi başl atma nız ve a rdın dan CMOS te miz l eme işl e min i
gerçekleştirmeden önce kapatmanız gereklidir. Parola, tarih, saat, kullanıcı
varsayılan proli, 1394 GUID ve MAC adresinin yalnızca CMOS pili çıkarıldığında
temizleneceğini lütfen aklınızda bulundurunuz.

Clear CMOSDefault

ASRock H61 Pro BTC Motherboard

Türkçe

89

1.4 Yerleşik Fişler ve Konektörler

Yerleşik şler ve konektörler jumper DEĞİLDİR. Bu şlerin ve konektörlerin üzerine
jumper kapakları YERLEŞTİRMEYİN. Fişlerin ve konektörlerin üzerine jumper
kapakları yerleştirmek anakartın kalıcı olarak zarar görmesine neden olabilir!

Seri ATAII Konektörler Bu dört Seri ATAII (SATAII)

(SATA2_0: bkz. s.2, No. 12)

(SATA2_1: bkz. s.2, No. 15)

(SATA2_2: bkz. s.2, No. 11)

(SATA2_3: bkz. s.2, No. 14)

SATA2_0

konektör, dahili depolama

cihazları için SATA veri

kablolarını destekler. Geçerli

SATA2_1

SATAII arayüzü 3,0 Gb/sn veri

SATA2_2

SATA2_3

aktarım hızına izin verir.

Seri ATA (SATA) SATA veri kablosunu her iki ucu

Veri Kablosu da SATA / SATAII sabit

(İsteğe bağlı)

diskine veya anakarttaki

SATAII konektörüne
bağlanabilir.

USB 2.0 Fişleri G/Ç panelindeki varsayılan

(9-pinli USB6_7)

(bkz. s.2 No. 18)

altı USB 2.0 portundan başka,

bu anakartta iki USB 2.0 şi
bulunur. Her USB 2.0 şi iki
USB 2.0 portunu destekler.

1

USB _PWR

P-9

P-8

USB _PWR

P+9

P+8

GND

GND

DUM MY

(9-pinli USB8_9)
(bkz. s.2 No. 17)

Türkçe

Kızılötesi Modülü Fişi Bu ş, isteğe bağlı bir kablosuz

(5-pinli IR1)

(bkz. s.2 No. 13)

aktarma ve alma kızılötesi

modülünü destekler.

90

ASRock H61 Pro BTC Motherboard

Ön Panel Ses Fişi Bu, panel ses kablosu için

(9-pinli HD_SES1)

(bkz. s.2 No. 20)

uygun bağlantı sağlayan ve

ses cihazlarını kontrol

etmeyi sağlayan bir arayüzdür.

1

GND

PRE SENC E#

MIC 2_R

MIC 2_L

MIC _RET

J_S ENSE

OUT 2_R

OUT _RET

OUT 2_L

1. Yükse Tanımlı Ses Jak Duyarlılığını destekler, ancak kasadaki panel
kablosunun HDA'nın düzgün çalışmasını desteklemesi gerekir. Lütfen
sisteminizi yüklemek için kılavuzumuzdaki ve kasa kılavuzundaki
talimatları izleyin.

2. AC'97 ses paneli kullanıyorsanız, lütfen ön panel ses şine aşağıdaki gibi
takın:

A. Mic_IN'i (MIC) MIC2_L'ye bağlayın.
B. Audio_R'yi (RIN) OUT2_R'ye ve Audio_L'yi (LIN) OUT2_L'ye bağlayın.
C. Ground'u (GND) Ground'a (GND) bağlayın.
D. MIC_RET ve OUT_RET yalnızca HD ses paneli içindir. Bunları AC’97 ses

paneli için bağlamanız gerekmez.

Sistem Paneli Fişi Bu ş, birçok sistem ön paneli

(9-pinli PANEL1)

(bkz. s.2 No. 16)

işlevini barındırır.

Kasa üzerindeki güç anahtarını, sıfırlama anahtarını ve sistem durumu
göstergesini aşağıdaki pin atamalarına göre bu bağlantıya bağlayın.
Kabloları bağlamadan önce pozitif ve negatif pinlere dikkat edin.

PWRBTN (Güç Anahtarı):

Kasa üzerindeki güç anahtarını ön panele bağlayın. Güç anahtarını
kullanarak sisteminizi kapatma şeklinizi yapılandırabilirsiniz.

RESET (Sıfırlama Anahtarı):

Kasa üzerindeki sıfırlama anahtarını ön panele bağlayın. Bilgisayar
donarsa veya normal bir yeniden başlatma gerçekleştirilemezse,
bilgisayarı yeniden başlatmak için sıfırlama anahtarına basın.

PLED (Sistem Gücü LED’i):

Kasa üzerindeki güç durumu göstergesini ön panele bağlayın. Sistem
çalışırken LED yanar. Sistem S1 uyku modunda iken LED yanıp sön
meye devam eder. Sistem S3/S4 uyku modunda veya kapalı (S5) iken

LED söner.
HDLED (Sabit Disk Çalışma LED’i):

Kasa üzerindeki sabit disk çalışma LED’ini ön panele bağlayın. Sabit
disk veri okurken veya yazarken LED yanar.

ASRock H61 Pro BTC Motherboard

Türkçe

91

Ön panel tasarımı kasaya göre değişiklik gösterebilir. Ön panel
modülünde temel olarak güç anahtarı, sıfırlama anahtarı, güç LED’i,
sabit disk çalışma LED’i, hoparlör vb. bulunur. Kasa ön panel
modülünüzü bu bağlantıya bağlarken, kablo atamalarının ve pin
atamalarının doğru biçimde eşleştirildiğinden emin olun.

Kasa Hoparlörü Fişi Lütfen kasa hoparlörünü bu şe

(4-pinli SPEAKER1)

(bkz. s.2 No. 10)

bağlayın.

Kasa/güç Fan Konektörü Lütfen kasa fan kablolarını

(4-pinli CHA_FAN1)

(bkz. s.2 No. 6)

fanına bu konektöre bağlayın

ve siyah kabloyu toprak pinine

bağlayın.

(4-pinli PWR_FAN1)
(bkz. s.2 No. 28)

Türkçe

CPU Fan Konektörü Lütfen fan kablolarını CPU

(4-pinli CPU_FAN1)

(bkz. s.2 No. 2)

fanına bu konektöre bağlayın

ve siyah kabloyu toprak pinine

bağlayın.

FAN_ SPEE D_CO NTRO L

CPU _FAN_ SPEE D

+12 V

GND

1 2 3 4

Bu anakart 4-Pinli CPU fan (Sessiz Fan) desteği sağlasa da, 3-Pinli CPU
fan hızı kontrol işlevi olmadan bile hala başarılı bir şekilde çalışabilir.
3-Pinli CPU fanı bu konektördeki CPU fan konektörüne bağlamayı
planlıyorsanız, lütfen Pin 1-3'e bağlayın.

Pin 1-3 Bağlı

3-Pinli Fanı Takma

ATX Güç Konektörü Lütfen bir ATX güç kaynağını

(24-pinli ATXPWR1)

(bkz. s.2 No. 5)

Bu anakart 24-pinli ATX güç konektörü sağlasa da

bu konektöre bağlayın.

12 124

13

12

24

geleneksel bir 20-pinli ATX güç kaynağı bağlarsanız da
çalışabilir. 20-pinli ATX güç kaynağını kullanmak için,
lütfen güç kaynağınızı Pin 1 ve Pin 13'le birlikte takın.

20-Pinli ATX Güç Kaynağını Takma

1

13

92

ASRock H61 Pro BTC Motherboard

ATX 12V Güç Konektörü Lütfen bir ATX 12V güç

(8-pinli ATX12V1)

(bkz. s.2 No. 3)

kaynağını bu konektöre

bağlayın.

8 5

4 1

Bu anakart 8-pinli ATX 12V güç konektörü sağlasa da geleneksel bir
4-pinli ATX 12V güç kaynağı bağlarsanız da çalışabilir. 4-pinli ATX güç
kaynağını kullanmak için, lütfen güç kaynağınızı Pin 1 ve Pin 5'le birlikte
takın.

8 5

4-Pinli ATX 12V Güç Kaynağını Takma

4 1

Seri port Fişi Bu COM1 şi bir seri port

(9-pinli COM1)

(bkz. s.2 No. 19)

modülünü destekler.

SLI/XFire Güç Konektörü üç grak kartı bu anakarta

(4-pinli SLI/XFIRE_PWR1)

(bkz. s.2 No. 29)

takılıyken lütfen bu bağlayıcıyı

güç beslemesi güç

bağlayıcısına bağlayın.

(4-pinli SLI/XFIRE_PWR2)
(bkz. s.2 No. 27)

ASRock H61 Pro BTC Motherboard

Türkçe

93

2. BIOS Bilgileri

Anakarttaki Flash Bellek BIOS Ayarları Yardımcı Programını içerir. Bilgisayarı
başlattığınızda, lütfen Otomatik Güç Sınaması (POST) sırasında BIOS Ayarları
yardımcı programına girmek için <F2> veya <Del> tuşuna basın; aksi halde, POST
test rutinlerine devam eder. BIOS Ayarlarına POST'tan sonra girmek istiyorsanız,
lütfen <Ctl> + <Alt> + <Delete> tuşlarına basarak veya sistem kasasındaki sıfırlama
düğmesine basarak sistemi yeniden başlatın. BIOS Ayarları programı kullanıcı
dostu olacak şekilde tasarlanmıştır. Çeşitli alt menüler arasında dolaşmanıza ve
önceden belirlenen seçenekler arasından seçim yapmanıza izin veren menü tabanlı
bir programdır. BIOS Ayarları hakkında ayrıntılı bilgi için, lütfen Destek CD'sinde
bulunan Kullanıcı Kılavuzu'na (PDF dosyası) başvurun.

3. Yazılım Destek CD’si bilgileri

Bu anakart çeşitli Microsoft® Windows® işletim sistemleri destekler: 8 / 8 64-bit / 7 / 7
64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit. Anakartla birlikte gelen Destek CD'si
anakart özelliklerini genişleten gerekli sürücüleri ve kullanışlı yardımcı programları
içerir. Destek CD'sini kullanmaya başlamak için, CD'yi CDROM sürücünüze takın.
Bilgisayarınızda "OTOMATİK KULLAN" özelliği etkinleştirilmişse, Ana Menüyü
otomatik olarak görüntüler. Ana Menü otomatik olarak görüntülenmezse, menüleri
görüntülemek için Destek CD'sinin “BIN” klasöründeki "ASSETUP.EXE" dosyasını
bulun ve çift tıklatın.

Türkçe

94

ASRock H61 Pro BTC Motherboard

1. 제품소개

ASRock 의
메인보드는 엄격한 품질관리 하에 생산되어진 신뢰성 있는 메인보드 입니다 . 이 제품
은 고 품격 디자인과 함께 ASRock 의 우수한 품질과 최고의 안정성을 자랑하고 있습
니다 . 이 빠른 설치 안내서에는 마더보드에 대한 설명과 단계별 설치 방법이 실려 있
습니다 . 마더보드에 대한 보다 자세한 내용은 지원 CD 의 사용 설명서에서 확인할 수
있습니다 .

메인보드의 사양이나 바이오스가 업 데이트 되기 때문에 이 사용자
설명서의 내용은 예고 없이 변경되거나 바뀔 수가 있습니다 . 만일을
생각해서 이 사용자 설명서의 어떤 변경이 있으면 ASRock 의 웹
사이트에서 언제든지 업 데이트를 하실 수 있습니다 . 웹사
이트에서 최신 VGA 카드와 CPU 지원 목록을 확인할 수 있습니다 .
ASRock 의 웹사이트 주소는 http://www.asrock.com 입니다 .
본 머더보드와 관련하여 기술 지원이 필요한 경우 당사 웹 사이트를 방문하
여 사용 중인 모델에 대한 특정 정보를 얻으십시오 .

1.1 패키지 내용

ASRock
ASRock
ASRock

시리얼 ATA (SATA) 데이터 케이블 2 개 ( 선택 사양 )
I/O 차폐 1 개

H61 Pro BTC

www.asrock.com/support/index.asp

H61 Pro BTC

H61 Pro BTC

H61 Pro BTC

메인 보드를 구매하여 주신것에 대하여 감사 드립니다 . 이

마더보드 (ATX 폼 팩터 )
퀵 설치 가이드
지원 CD

ASRock은사용자에게 알립니다

Windows® 8 / 8 64-비트 / 7 / 7 64-비트 / Vista

성능을 향상시키기 위해서 Storage C onf iguration(스토리지 구성)에서
BIOS 옵션을 AHCI 모드로 설정하는 것이 좋습니다. BIOS 설정과 관련하
여 자세한 내용은 지원 CD에 포함된 “사용 설명서”를 참조하십시오.

...

TM

/ VistaTM 64-비트의

ASRock H61 Pro BTC Motherboard

한 국 어

95

한 국 어

1.2 설명서

플랫폼 - ATX 폼 팩터

- 완전 고체 축전지 디자인
CPU - LGA1155 패키지에서 3 세대 및 2 세대 Intel® CoreTM i7 / i5 /
i3 / Xeon® / Pentium® / Celeron®을 지원합니다

- Intel® Turbo Boost 2.0 기술 지원

- K- 시리즈 잠금 해제 CPU 지원

- 하이퍼 - 스레딩 기술 지원
칩셋 - Intel® H61

- Intel® Rapid Start 기술과 Smart Connect 기술을 지원합니다
메모리 - 듀얼 채널 메모리 기술 지원

- DDR3 DIMM 슬롯 2 개

- DDR3 1600/1333/1066 비 -ECC, 언버퍼드 메모리를 지원
(Intel® Ivy Bridge CPU 를 탑재한 DDR3 1600, Intel® Sandy
Bridge CPU 를 탑재한 DDR3 1333)

- 최대 시스템 메모리 용량 : 16GB

- Intel® Ivy Bridge CPU 에서 Intel® 익스트림 메모리 프로파일
(XMP)1.3/1.2 지원
확장 슬롯 - PCI Express 3.0 x16 슬롯 (x16 모드의 경우 PCIE2) 1 개
* PCIE 3.0 은 Intel® Ivy Bridge CPU 에서만 지원됩니다 .
Intel® Sandy Bridge CPU 는 PCIE 2.0 만 지원합니다 .

- PCI Express 2.0 x1 슬롯 5 개
온보드 VGA * Intel® HD Graphics 내장 비주얼 및 VGA 출력은 GPU 통합된
프로세서의 경우에만 지원됩니다 .

- Intel® Ivy Bridge CPU 에서 Intel® HD 그래픽 내장 비주얼 프
로그램 : Intel® Quick Sync Video 2.0, Intel® InTruTM 3D,
Intel® Clear Video HD Technology, Intel® InsiderTM, Intel®
HD Graphics 2500/4000

- Intel® Sandy Bridge CPU 에서 Intel® HD 그래픽 내장 비주
얼 프로그램 : Intel® Quick Sync Video, Intel® InTruTM 3D,
Intel® Clear Video HD Technology, Intel® HD Graphics
2000/3000, Intel® Advanced Vector Extensions (AVX)

- Intel® Ivy Bridge CPU 를 탑재한 DirectX 11, Pixel Shader 5.0.
Intel® Sandy Bridge CPU 를 탑재한 DirectX 10.1, Pixel

Shader 4.1

- Intel® Ivy Bridge CPU 에서 최대 공유 메모리 1760MB. Intel®
Sandy Bridge CPU 에서 최대 공유 메모리 1759MB.

- 더블 VGA 수출 : HDMI 와 D-Sub 포트 독립 디스플레이 컨
트롤러를 지원

- 최대 해상도 1920x1200 @ 60Hz 까지 HDMI 지원

96

ASRock H61 Pro BTC Motherboard

- 최대 해상도 2048x1536 @ 75Hz 까지 D-Sub 지원

- 자동 립 싱크 (Auto Lip Sync), 딥 컬러 (Deep Color)(12bpc),
xvYCC, HBR( 고비트율 오디오 ), HDMI 지원
(HDMI 호환 모니터 필요 )

- HDMI 포트를 이용한 HDCP 기능 지원

- HDMI 포트를 이용한 1080p Blu-ray (BD) /
HD-DVD 재생을 지원
오디오 - 5.1 CH HD Audio (VIA® VT1705 Audio Codec)
랜 - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- 웨이크 - 온 - 랜 지원

- LAN 케이블 감지 지원

- 절전형 이더넷 802.3az 지원

- PXE 지원
후면판 I/O - 1 개 PS/2 마우스 포트

- 1 개 PS/2 키보드 포트

- 1 개의 D-Sub 포트

- 1 개의 HDMI 포트

- 6 개디폴트 USB 2.0 포트

- 1 개 LED(ACT/LINK LED 및 SPEED LED) 가 있는 RJ-45
LAN 포트

- 오디오 잭 : 라인 인 / 전방 스피커 / 마이크
스토리지 - 4 개 의 SATA2 3.0Gb/s 커넥터 , NCQ, AHCI 및“핫 플러그”
인터페이스 기 능 지원
온보드 헤더 - 적외선 모듈 헤더 1 개
및 커넥터 - COM 포트 헤더 1 개

- CPU 팬 커넥터 1 개 (4 핀 )

- 섀시 팬 커넥터 1 개 (4 핀 )

- 전원 팬 커넥터 1 개 (4 핀 )

- 24 핀 ATX 전원 헤더 1 개

- 8 핀 ATX 12V 파워 콘넥터 1 개

- SLI/XFire 전원 헤더 2 개

- 전면부 오디오 콘넥터 1 개

- USB 2.0 헤더 2 개 (4 개의 추가 USB 2.0 포트를 지원하는 헤더
2 개 )
BIOS - 32Mb AMI BIOS

- GUI 지원을 제공하는 AMI UEFI 적합형 BIOS

- “플러그 앤 플레이” 지원

- ACPI 1.1 웨이크 - 업 이벤트와의 호환

- 점퍼 프리 지원

- SMBIOS 2.3.1 지원

한 국 어

ASRock H61 Pro BTC Motherboard

97

- IGPU, DRAM, PCH, CPU PLL, VTT, VCCSA 전압 멀티
조절
지원 CD - 드라이버 , 유틸리티 , 백신 소프트웨어 ( 시험판 ), Google
Chrome Browser 및 Toolbar
하드웨어 모니터 - CPU 온도 감지

- 마더보드 온도 감지

- CPU/ 섀시 / 전원 팬 회전 속도계 : 샤시 ( 케이스 ) 팬 회전 속
도계

- CPU/ 섀시 저소음 팬 (CPU 온도에 의한 섀시 팬속도 자동 조정
가능 )

- CPU/ 섀시팬 멀티스피드 컨트롤

- 전압 감시 기능 : +12V,+5V,+3.3V,Vcore
OS - 마이크로 소프트 Windows® 8/8 64 비트 /7/7 64 비트 /VistaTM/
Vista
인증서 - FCC, CE, WHQL

- ErP/EuP 지원 (ErP/EuP 지원 전원 공급기가 요구됨 )

* 상세한 제품정보는 당사의 웹사이트를 방문할수있습니다 . http://www.asrock.com

TM

64 비트 / XP/XP 64 비트 와 호환

한 국 어

98

ASRock H61 Pro BTC Motherboard

1.3 점퍼 셋팅

그림은 점퍼를 어떻게 셋업 하는지를 보여줍니다 .
점퍼 캡이 핀 위에 있을 때 , 점퍼는 “쇼트”입니다 .
점퍼 캡이 핀 위에 없을 때 점퍼는 “오픈” 입니다 .
그림은 3 개의 핀 중 1-2 번 핀이 “쇼트”임을
보여주는 것이며 , 점퍼 캡이 이 두 핀 위에 있음을
보여주는 것입니다 .

점퍼 세팅

CMOS 초기화

(CLRCMOS1, 3 핀 점퍼 )
(2 페이지 , 9 번 항목 참조 )

참고 :

CLRCMOS1 을 사용하여 CMOS 에 들어 있는 데이터를 삭제할 수 있습니다 .
시스템 매개변수를 삭제하고 기본 설정으로 복원하려면 , 컴퓨터를 끄고 전원
공급장치에서 플러그를 뽑으십시오 . 15 초를 기다린 다음 점퍼 캡을 사용하여
CLRCMOS1 의 핀 2 와 핀 3 을 5 초 동안 단락하십시오 . 그러나 BIOS 업데이트
직후에는 CMOS 를 삭제하지 마십시오 . BIOS 를 업데이트하자마자 CMOS 를
삭제해야 하는 경우 먼저 시스템을 부팅하고 CMOS 를 종료하고 삭제 작업을 해
야 합니다 . CMOS 배터리를 제거할 경우에만 암호 , 날짜 , 시간 , 사용자 기본 프
로파일 , 1394 GUID, MAC 주소가 삭제됩니다 .

CMOS 삭제기본 설정

ASRock H61 Pro BTC Motherboard

한 국 어

99

1.4 온보드 헤더 및 커넥터

주의 !

세요 . 커넥터에 점퍼 캡을 설치하면 마더보드가 영구적으로 손상됩니다 !

콘넥터 그림 설명

시리얼 ATAII 커넥터 4 개의 시리얼 ATAII

(SATA2_0: 2 페이지 , 12 번 항목 참조 )

(SATA2_1: 2 페이지 , 15 번 항목 참조 )

(SATA2_2: 2 페이지 , 11 번 항목 참조 )

(SATA2_3: 2 페이지 , 14 번 항목 참조 )

지원합니다 . 현재의 SATAII
인터페이스는 최고 3.0 Gb/s 의
데이터 전송 속도를
지원합니다 .

이 콘넥터는 점퍼가 아닙니다 . 이 콘넥터 위에 점퍼 캡을 사용하지마

(SATA) 커넥터는 내부 저장 장

SATA2_0

SATA2_2

치용 SATA 데이터 케이블을

지원합니다 . 커넥터가 내부

SATA2_1

기억 장치용 SATA 케이블을

SATA2_3

한 국 어

시리얼 ATA(SATA)
데이터 케이블

( 선택 사양 )

SATA 데이터 케이블의 임의
적인 측을 마더보드의 SATA /
SATAII 하드 디스크
혹은 SATAII 커넥터
에 연결합니다 .

USB 2.0 헤더

(9 핀 USB6_7)

(2 페이지 , 18 번 항목 참조 )

본 머더보드에는 I/O 패널에 있

는 6 개의 기본 USB 2.0 포트

외에도 USB 2.0 헤더가 2 개 있
습니다 . 각각의 USB 2.0 헤더
는 2 개의 USB 2.0 포트를 지원
할 수 있습니다 .

(9 핀 USB8_9)
(2 페이지 , 17 번 항목 참조 )

1

USB _PWR

P-9

P-8

USB _PWR

P+9

P+8

GND

GND

DUM MY

적외선 모듈 헤더 이 헤더는 선택품목인 무선

(5 핀 IR1)

적외선 송수신 모듈을

(2 페이지 , 13 번 항목 참조 )

지원합니다 .

100

ASRock H61 Pro BTC Motherboard