ASRock H61M-DPS User Manual [en, ru, fr, de, es]

No part of this installation guide may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this guide may or may not be registered trademarks or copyrights of their respective companies, and are used only for identiﬁ ca- tion or explanation and to the owners’ beneﬁ t, without intent to infringe.

Disclaimer:

Speciﬁ cations and information contained in this guide are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this guide. With respect to the contents of this guide, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or ﬁ tness for a particular purpose. In no event shall ASRock, its directors, ofﬁ cers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of proﬁ ts, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

Published December 2012

ASRock H61M-DPS Motherboard

English

Motherboard Layout

CPU_FAN1

RoHS

Keyboard

PS2

VGA1

Mouse

PS2

ATX12V1

Fast LAN

DVI1

USB2.0 T:USB0 B:USB1

LAN PHY

USB 2.0 T: U SB 2 B: USB3

Bottom:

MIC IN

FRONT

25 24

HD_AUDIO1

Center:

Top: RJ-45

Top:

LINE IN

Super

AUDIO CODEC

Fast USB

PWR_FAN1

H61M-DPS

Fast RAM

PCIE1

I/O

PCIE2

CMOS

Battery

CLRCMOS1

CI1

PCI1

LPT1

USB4_5

COM1

USB6_7

CIR1

Intel

H61

SATA_3

SATA_2

DDR3_B1 (64bit, 240-pin module)

DDR3_A1 (64bit, 240-pin module)

SATA_1

SATA_0

PLED PWRBTN

SPEAKER1

32Mb BIOS

CHA_FAN1

PANEL1

ATXPWR1

HDLED RESET

11 12

English

1 Power Fan Connector (PWR_FAN1) 14 SATA2 Connector (SATA_0) 2 ATX 12V Power Connector (ATX12V1) 15 SATA2 Connector (SATA_2) 3 1155-Pin CPU Socket 16 USB 2.0 Header (USB6_7) 4 CPU Fan Connector (CPU_FAN1) 17 USB 2.0 Header (USB4_5) 5 2 x 240-pin DDR3 DIMM Slots 18 Consumer Infrared Module Header (CIR1) (Dual Channel: DDR3_A1, DDR3_B1) 19 COM Port Header (COM1) 6 ATX Power Connector (ATXPWR1) 20 Print Port Header (LPT1) 7 System Panel Header (PANEL1) 21 Front Panel Audio Header (HD_AUDIO1) 8 Intel H61 Chipset 22 PCI Slot (PCI1) 9 Chassis Speaker Header (SPEAKER1) 23 Chassis Intrusion Header (CI1) 10 32Mb SPI Flash 24 Clear CMOS Jumper (CLRCMOS1) 11 SATA2 Connector (SATA_3) 25 PCI Express 2.0 x1 Slot (PCIE2) 12 SATA2 Connector (SATA_1) 26 PCI Express 3.0 x16 Slot (PCIE1) 13 Chassis Fan Connector (CHA_FAN1)

ASRock H61M-DPS Motherboard

I/O Panel

1 PS/2 Mouse Port (Green) 6 USB 2.0 Ports (USB23) * 2 LAN RJ-45 Port 7 USB 2.0 Ports (USB01) 3 Line In (Light Blue) 8 DVI-D Port ** 4 Front Speaker (Lime) 9 D-Sub Port 5 Microphone (Pink) 10 PS/2 Keyboard Port (Purple)

* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED indications.

Activity/Link LED SPEED LED

Status Description Status Description

LAN Port LED Indications

Off No Link Off 10Mbps connection Blinking Data Activity Orange 100Mbps connection On Link Green 1Gbps connection

ACT/LINK LED

LAN Port

SPEED LED

** To enable Multi-Streaming function, you need to connect a front panel audio cable to the front panel audio header. Please refer to below steps for the software setting of Multi-Streaming. For Windows After restarting your computer, you will ﬁ nd “Mixer” tool on your system. Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click “ok”. Choose “2CH” or

“4CH” and then you are allowed to select “Realtek HDA Primary output” to use Rear Speaker and Front Speaker, or select “Realtek HDA Audio 2nd output” to use front panel audio. Then reboot your system. For Windows After restarting your computer, please double-click “Realtek HD Audio Manager” on the system tray. Set “Speaker Conﬁ guration” to “Quadraphonic” or “Stereo”. Click “Device advanced settings”, choose “Make front and rear output devices playbacks two different audio streams simultaneously”, and click “ok”. Then reboot your system.

XP:

8 / 7 / VistaTM:

ASRock H61M-DPS Motherboard

English

1. Introduction

Thank you for purchasing ASRock H61M-DPS motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance. This Quick Installation Guide contains introduction of the motherboard and step-bystep installation guide. More detailed information of the motherboard can be found in the user manual presented in the Support CD.

Because the motherboard speciﬁ cations and the BIOS software might be updated, the content of this manual will be subject to change without notice. In case any modiﬁ cations of this manual occur, the updated version will be available on ASRock website without further notice. You may ﬁ nd the latest VGA cards and CPU support lists on ASRock website as well. ASRock website http://www.asrock.com If you require technical support related to this motherboard, please visit our website for speciﬁ c information about the model you are using. www.asrock.com/support/index.asp

1.1 Package Contents

ASRock H61M-DPS Motherboard (Micro ATX Form Factor) ASRock H61M-DPS Quick Installation Guide ASRock H61M-DPS Support CD 2 x Serial ATA (SATA) Data Cables (Optional) 1 x I/O Panel Shield

English

ASRock Reminds You...

To get better performance in Windows® 8 / 8 64-bit / 7 / 7 64-bit / Vista VistaTM 64-bit, it is recommended to set the BIOS option in Storage Conﬁ guration to AHCI mode. For the BIOS setup, please refer to the “User Manual” in our support CD for details.

ASRock H61M-DPS Motherboard

1.2 Speciﬁ cations

Platform - Micro ATX Form Factor

- Solid Capacitor for CPU power

CPU - Supports 3 LGA1155 Package

- Supports Intel

- Supports K-Series CPU Chipset - Intel® H61

- Supports Intel® Rapid Start Technology and Smart Connect Technology Memory - Dual Channel DDR3 Memory Technology

- 2 x DDR3 DIMM slots

- Supports DDR3 1600/1333/1066 non-ECC, un-buffered memory (DDR3 1600 with Intel 1333 with Intel® Sandy Bridge CPU)

- Max. capacity of system memory: 16GB (see CAUTION 1)

- Supports Intel Intel® Ivy Bridge CPU Expansion Slot - 1 x PCI Express 3.0 x16 slot (PCIE1 @ x16 mode)

* PCIE 3.0 is only supported with Intel® Ivy Bridge CPU. With Intel® Sandy Bridge CPU, it only supports PCIE 2.0.

- 1 x PCI Express 2.0 x1 slot

- 1 x PCI slot

Graphics * Intel be supported only with processors which are GPU integrated.

- Supports Intel Sync Video 2.0, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel® InsiderTM, Intel® HD Graphics 2500/4000 with Intel

- Supports Intel® HD Graphics Built-in Visuals: Intel® Quick Sync Video, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel® HD Graphics 2000/3000, Intel® Advanced Vector Extensions (AVX) with Intel® Sandy Bridge CPU

- Pixel Shader 5.0, DirectX 11 with Intel Pixel Shader 4.1, DirectX 10.1 with Intel® Sandy Bridge CPU.

- Max. shared memory 1760MB with Intel Max. shared memory 1759MB with Intel® Sandy Bridge CPU.

and 2nd Generation Intel® CoreTM i7 / i5 / i3 in

Turbo Boost 2.0 Technology

Ivy Bridge CPU, DDR3

Extreme Memory Proﬁ le (XMP) 1.3 / 1.2 with

HD Graphics Built-in Visuals and the VGA outputs can

HD Graphics Built-in Visuals: Intel® Quick

Ivy Bridge CPU

Ivy Bridge CPU.

English

ASRock H61M-DPS Motherboard

English

- Dual VGA Output: support DVI and D-Sub ports by independent display controllers

- Supports DVI with max. resolution up to 1920x1200 @ 60Hz

- Supports D-Sub with max. resolution up to 2048x1536 @ 75Hz

- Supports HDCP function with DVI port

- Supports Full HD 1080p Blu-ray (BD) / HD-DVD playback with DVI port

Audio - 5.1 CH HD Audio (Realtek ALC662 Audio Codec) LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Supports LAN Cable Detection

- Supports Energy Efﬁ cient Ethernet 802.3az

- Supports PXE Rear Panel I/O I/O Panel

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x D-Sub Port

- 1 x DVI-D Port

- 4 x Ready-to-Use USB 2.0 Ports

- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED LED)

- HD Audio Jack: Line in / Front Speaker / Microphone Connector - 4 x SATA2 3.0 Gb/s connectors, support NCQ, AHCI and Hot Plug functions

- 1 x CIR header

- 1 x Print Port header

- 1 x COM port header

- 1 x Chassis Intrusion header

- 1 x CPU Fan connectors (4-pin)

- 1 x Chassis Fan connector (4-pin)

- 1 x Power Fan connector (3-pin)

- 24 pin ATX power connector

- 4 pin 12V power connector

- Front panel audio connector

- 2 x USB 2.0 headers (support 4 USB 2.0 ports) BIOS Feature - 32Mb AMI UEFI Legal BIOS with GUI support

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

ASRock H61M-DPS Motherboard

- SMBIOS 2.3.1 Support Support CD - Drivers, Utilities, AntiVirus Software (Trial Version), CyberLink MediaEspresso 6.5 Trial, Google Chrome Browser and Toolbar Hardware - CPU Temperature Sensing Monitor - Chassis Temperature Sensing

- CPU Fan Tachometer

- Chassis Fan Tachometer

- CPU Quiet Fan (Allow Chassis Fan Speed Auto-Adjust by CPU Temperature)

- CPU/Chassis Fan Multi-Speed Control

- CASE OPEN detection

- Voltage Monitoring: +12V, +5V, +3.3V, CPU Vcore OS - Microsoft® Windows® 8 / 8 64-bit / 7 / 7 64-bit / Vista

VistaTM 64-bit / XP / XP 64-bit compliant Certiﬁ cations - FCC, CE, WHQL

- ErP/EuP Ready (ErP/EuP ready power supply is required)

* For detailed product information, please visit our website: http://www.asrock.com

WARNING

Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using third-party overclocking tools. Overclocking may affect your system’s stability, or even cause damage to the components and devices of your system. It should be done at your own risk and expense. We are not responsible for possible damage caused by overclocking.

CAUTION!

1. Due to the operating system limitation, the actual memory size may be less than 4GB for the reservation for system usage under Windows bit CPU, there is no such limitation. You can use ASRock XFast

RAM to utilize the memory that Windows® cannot use.

8 / 7 / VistaTM / XP. For Windows® OS with 64-

ASRock H61M-DPS Motherboard

English

1.3 Pin Header Easy Installation Guide

ASRock motherboard is equipped with pin headers with obvious colors which indicate you to recognize the crucial headers more easily. Please refer to below illustrations for the pin deﬁ nition of onboard headers. If you want to have more information about the usage of these headers, please refer to “Jumpers Setup“ and “Onboard Headers and Connectors“ for details.

DUMMY

REST#

GND

PWRBTN#

PLED-

PLED+

System Panel Header

GND

HDLED-

HDLED+

English

GND

PRESENCE#

MIC_RET

OUT_RET

OUT2_L

J_SENSE

OUT2_R

MIC2_R

MIC2_L

Front Panel Audio Header

ASRock H61M-DPS Motherboard

USB_PWR

P-

P+

GND

DUMMY

GND

P+

P-

USB_PWR

USB 2.0 Header

SPEAKER

DUMMY

+5V

Chassis Speaker Header

1.4 Jumpers Setup

The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when jumper cap is placed on these 2 pins.

Jumper Setting Description

Clear CMOS Jumper

(CLRCMOS1) (see p.2, No. 23)

Note: CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug

the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just ﬁ nish updating the BIOS, you must boot up the system ﬁ rst, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time and user default proﬁ le will be cleared only if the CMOS battery is removed.

Clear CMOSDefault

If you clear the CMOS, the case open may be detected. Please adjust

the BIOS option “Clear Status” to clear the record of previous chassis intrusion status.

ASRock H61M-DPS Motherboard

English

1.5 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!

Serial ATA2 Connectors These four Serial ATA2

(SATA_0: see p.2, No. 13)

(SATA_1: see p.2, No. 11)

(SATA_2: see p.2, No. 14)

(SATA_3: see p.2, No. 10)

3.0 Gb/s data transfer rate.

Serial ATA (SATA) Either end of the SATA data Data Cable cable can be connected to the

(Optional)

SATA2 hard disk or the SATA2

connector on this motherboard.

USB 2.0 Headers Besides four default USB 2.0

(9-pin USB4_5)

(see p.2 No. 16)

ports on the I/O panel, there

this motherboard. Each USB 2.0 header can support two USB 2.0 ports.

(9-pin USB6_7) (see p.2 No. 15)

(SATA2) connectors support

SATA_3 SATA_1

SATA data cables for internal storage devices. The current

SATA_2 SATA_0

SATA2 interface allows up to

are two USB 2.0 headers on

English

Consumer Infrared Module Header This header can be used to

(4-pin CIR1)

(see p.2 No. 17)

connect the remote

controller receiver.

ASRock H61M-DPS Motherboard

Front Panel Audio Header This is an interface for front

(9-pin HD_AUDIO1)

(see p.2 No. 20)

panel audio cable that allows

convenient connection and

control of audio devices.

GND

PRESENCE#

MIC2_R

MIC2_L

MIC_RET

J_SENSE

OUT2_R

OUT_RET

OUT2_L

1. High Deﬁ nition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system.

2. If you use AC’97 audio panel, please install it to the front panel audio header as below:

A. Connect Mic_IN (MIC) to MIC2_L. B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L. C. Connect Ground (GND) to Ground (GND). D. MIC_RET and OUT_RET are for HD audio panel only. You don’t

need to connect them for AC’97 audio panel.

E. To activate the front mic. For Windows

XP / XP 64-bit OS:

Select “Mixer”. Select “Recorder”. Then click “FrontMic”.

For Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS: Go to the "FrontMic" Tab in the Realtek Control panel. Adjust

“Recording Volume”.

System Panel Header This header accommodates

(9-pin PANEL1)

(see p.2 No. 7)

several system front panel functions.

Connect the power switch, reset switch and system status indicator on the

chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

PWRBTN (Power Switch): Connect to the power switch on the chassis front panel. You may conﬁ gure

the way to turn off your system using the power switch.

RESET (Reset Switch):

Connect to the reset switch on the chassis front panel. Press the reset

switch to restart the computer if the computer freezes and fails to perform a normal restart.

ASRock H61M-DPS Motherboard

English

PLED (System Power LED): Connect to the power status indicator on the chassis front panel. The LED

is on when the system is operating. The LED keeps blinking when the system is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered off (S5).

HDLED (Hard Drive Activity LED): Connect to the hard drive activity LED on the chassis front panel. The LED

is on when the hard drive is reading or writing data.

The front panel design may differ by chassis. A front panel module mainly

consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assign-ments are matched correctly.

Chassis Speaker Header Please connect the chassis

(4-pin SPEAKER 1)

(see p.2 No. 8)

speaker to this header.

English

Chassis and Power Fan Connectors Please connect the fan cables

(4-pin CHA_FAN1)

(see p.2 No. 12)

to the fan connectors and

match the black wire to the

CHA_FAN_SPEED

+12V

FAN_SPEED_CONTROL

GND

ground pin.

(3-pin PWR_FAN1) (see p.2 No. 1)

CPU Fan Connector Please connect the CPU fan

(4-pin CPU_FAN1)

(see p.2 No. 4)

cable to the connector and

match the black wire to the

ground pin.

Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin

CPU fan still can work successfully even without the fan speed control function. If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this motherboard, please connect it to Pin 1-3.

GND +12V PWR_FAN_SPEED

4 3 2 1

+12V

FAN_SPEED_CONTROL

CPU_FAN_SPEED

GND

Pin 1-3 Connected

3-Pin Fan Installation

ASRock H61M-DPS Motherboard

ATX Power Connector Please connect an ATX power

(24-pin ATXPWR1)

supply to this connector.

12 124

(see p.2 No. 6)

Though this motherboard provides 24-pin ATX power connector,

it can still work if you adopt a traditional 20-pin ATX power supply. To use the 20-pin ATX power supply, please plug your power supply along with Pin 1 and Pin 13.

20-Pin ATX Power Supply Installation

ATX 12V Power Connector Please connect an ATX 12V

(4-pin ATX12V1)

(see p.2 No. 2)

power supply to this connector.

Chassis Intrusion Header This motherboard supports

(2-pin CI1)

CASE OPEN detection feature

(see p.2, No. 22)

that detects if the chassis cover

Signal

GND

has been removed. This feature requires a chassis with chassis intrusion detection design.

Print Port Header This is an interface for print

(25-pin LPT1)

(see p.2 No. 19)

port cable that allows

convenient connection of printer

devices.

AFD#

STB#

ERROR#

PINIT#

SPD1

SPD0

SLIN#

SPD2

SPD3

SPD4

SPD5

SPD6

GND

SPD7

ACK#

BUSY

SLCT

Serial port Header This COM1 header supports a

(9-pin COM1)

(see p.2 No. 18)

serial port module.

ASRock H61M-DPS Motherboard

English

2. BIOS Information

The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up the computer, please press <F2> or <Del> during the Power-On-Self-Test (POST) to enter BIOS Setup utility; otherwise, POST continues with its test routines. If you wish to enter BIOS Setup after POST, please restart the system by pressing <Ctl> + <Alt> + <Delete>, or pressing the reset button on the system chassis. The BIOS Setup program is designed to be user-friendly. It is a menu-driven program, which allows you to scroll through its various sub-menus and to select among the predetermined choices. For the detailed information about BIOS Setup, please refer to the User Manual (PDF ﬁ le) contained in the Support CD.

3. Software Support CD information

This motherboard supports various Microsoft 64-bit / 7 / 7 64-bit / VistaTM / Vista came with the motherboard contains necessary drivers and useful utilities that will enhance motherboard features. To begin using the Support CD, insert the CD into your CD-ROM drive. It will display the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main Menu does not appear automatically, locate and double-click on the ﬁ le “ASSETUP.EXE” from the BIN folder in the Support CD to display the menus.

64-bit / XP / XP 64-bit. The Support CD that

Windows® operating systems: 8 / 8

English

ASRock H61M-DPS Motherboard

Speziﬁ kationen

Plattform - Micro ATX-Formfaktor

- Festkondensator für CPU-Leistung CPU - Unterstützt Intel und 2ten Generation im LGA1155-Package

- Unterstützt Intel

- Unterstützt CPU der K-Serie Chipsatz - Intel® H61

- Unterstützt Intel® Rapid Start Technology und Smart Connect Technology Speicher - Unterstützung von Dual-Kanal-Speichertechnologie

- 2 x Steckplätze für DDR3

- Unterstützt DDR3 1600/1333/1066 non-ECC, ungepufferter Speicher (DDR3 1600 mit Intel DDR3 1333 mit Intel® Sandy Bridge-Prozessor)

- Max. Kapazität des Systemspeichers: 16GB

- Unterstützt Intel Intel® Ivy Bridge-Prozessor Erweiterungs- - 1 x PCI Express 3.0 x16-Steckplatz (PCIE1 für x16-Modus) steckplätze * PCIE 3.0 wird nur mit Intel® Ivy Bridge-Prozessor unterstützt. Mit Intel® Sandy Bridge-Prozessor wird nur PCIE 2.0 unterstützt.

- 1 x PCI Express 2.0 x1-Steckplätze

- 1 x PCI-Steckplätze Onboard-VGA * Integrierte Intel Ausgänge können nur durch GPU-integrierte Prozessoren unterstützt werden.

- Unterstützt hochauﬂ ösende integrierte Intel Intel® Quick-Sync-Video 2.0, Intel® InTruTM 3D, Intel® Clear Video-Technik (HD), Intel 2500/4000 mit Intel® Ivy Bridge-Prozessor

- Unterstützt hochauﬂ ösende integrierte Intel®-Graﬁ klösungen: Intel® Quick-Sync-Video, Intel® InTruTM 3D, Intel® Clear Video-Technik (HD), Intel® HD Graphics 2000/3000, Intel® Advanced Vector Extensions (AVX) mit Intel Prozessor

- Pixel Shader 5.0, DirectX 11 mit Intel Pixel Shader 4.1, DirectX 10.1 mit Intel® Sandy Bridge Prozessor

- Maximal gemeinsam genutzter Speicher 1760MB mit Intel®

CoreTM i7- / i5- / i3-Prozessoren der 3ten

Turbo Boost 2.0-Technologie

Ivy Bridge-Prozessor,

Extreme Memory Proﬁ le (XMP)1.3/1.2 mit

HD-Graﬁ kdarstellungen und die VGA-

-Graﬁ klösungen:

InsiderTM, Intel® HD Graphics

Sandy Bridge-

Ivy Bridge-Prozessor,

Deutsch

ASRock H61M-DPS Motherboard

Deutsch

Ivy Bridge-Prozessor. Maximal gemeinsam genutzter Speicher 1759MB mit Intel® Sandy Bridge-Prozessor.

- Doppel-VGA Ausgabe: unterstützt DVI und D-Sub Ports durch unabhängige Bildschirmanzeige Kontrolleure

- Unterstützt DVI mit einer maximalen Auﬂ ösung von 1920 x 1200 bei 60 Hz

- Unterstützt D-Sub mit einer maximalen Auﬂ ösung von 2048 x 1536 bei 75 Hz

- Unterstützt HDCP-Funktion mit DVI-Port

- Unterstutzt 1080p Blu-ray (BD) / HD-DVD-Wiedergabe mit DVI-Port

Audio - 5.1 CH HD Audio (Realtek ALC662 Audio Codec) LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Unterstützt LAN-Kabelerkennung

- Unterstützt energieefﬁ zientes Ethernet 802.3az

- Unterstützt PXE E/A-Anschlüsse I/O Panel an der - 1 x PS/2-Mausanschluss Rückseite - 1 x PS/2-Tastaturanschluss

- 1 x D-Sub port

- 1 x DVI-D port

- 4 x Standard-USB 2.0-Anschlüsse

- 1 x RJ-45 LAN Port mit LED (ACT/LINK LED und SPEED LED)

- HD Audiobuchse: Audioeingang / Lautsprecher vorne / Mikrofon Anschlüsse - 4 x SATA2 3,0 GB/s-Anschlüsse, unterstützen NCQ-, AHCI- und „Hot Plug“ (Hot-Plugging)- Funktionen

- 1 x

- 1 x Druckerport-Anschlussleiste

- 1 x COM-Anschluss-Header

- 1 x Verteiler für Gehäuseeindringversuche

- 1 x CPUlüfter-Anschluss (4-pin)

- 1 x Gehäuselüfter-Anschluss (4-pin)

- 1 x Stromlüfter-Anschluss (3-pin)

- 24-pin ATX-Netz-Header

- 4-pin anschluss für 12V-ATX-Netzteil

- Anschluss für Audio auf der Gehäusevorderseite

- 2 x USB 2.0-Anschlüsse (Unterstützung 4 zusätzlicher USB 2.0-Anschlüsse)

Consumer Infrared-Modul-Header

ASRock H61M-DPS Motherboard

+ 35 hidden pages