Asrock H470 Phantom Gaming 4 Quick Installation Guide

Version 1.0
Published May 2020
Copyright©2020 ASRock INC. All rights reserved.

Copyright Notice:

No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.

Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of prots, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”

ASRock Website: http://www.asrock.com

AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage caused by our goods. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. If you require assistance please call ASRock Tel

: [phone] ext.123 (Standard International call charges apply)

e terms HDMI® and HDMI High-Denition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United

States and other countries.

Motherboard Layout

Intel

H470

DDR 4_A2 (6 4 bit, 28 8-pin m odule )

DDR 4_A1 (6 4 bit, 28 8-pin m odule )

DDR 4_B2 (6 4 bit, 28 8-pin m odule )

DDR 4_B1 (6 4 bit, 28 8-pin m odule )

ATX12V1

ATXP WR 1

PCIE2

PCIE4

HDLED RESET

PLED PWRBTN

PANEL1

1

USB_5_6

1

1

SPK_PLED1

1

HD_AUDIO1

PCIE1

RoHS

13

16

19

20

1

Ultra M.2

PCIe Gen3 x4

CMOS

Battery

PCIE3

31

15

10

USB3_ 3_4

1

11

SATA3_4

SATA3_5

SATA3_0

SATA3_1

SATA3_2

SATA3_3

CLRMOS1

1

M2_ WIFI1

M2_WIFI_CT1

M2_ 2

C 6

C 5

C 4

T B1

1

2

PCIE5

T

T

T

AUDIO
CODEC

SUPER

I/O

USB3_5_6

1

14

21

23

24

25

29

22

4

3

CHA_FAN 1/WP

CHA_FAN2/WP

CHA_FAN3/WP

CPU_FAN2/WP

ATX12V2

CPU_FAN1

5

6

12

CHA_FAN 4/WP

17

1

SPI_TPM_J1

18

27

ADDR_LED1

1

RGB_LED1

1

26

30

ADDR_LED2

1

RGB_LED2

1

7

8

32

CPU

DRAM

VGA

BOOT

9

USB 2. 0

T: USB_1

B: USB _2

Top:
RJ-45

USB 3.2 Gen1
T: USB3_1
B: USB3_2

PS2

Keybo ard

/Mous e

Top:

LINE I N

Cent er:

FRON T

Bott om:

MIC IN

USB 3.2 Gen2
T:USB31_TA_1
B: USB31_TC_1

HDM I1

Dis play1

USB_3_4

1

28

C 7

T

M2_ 1

C 2

C 1

T

T

H470 Phantom Gaming 4

English

1

English

No. Description

1 ATX 12V Power Connector (ATX12V1)

2 ATX 12V Power Connector (ATX12V2)

3 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)

4 2 x 288-pin DDR4 DIMM Slots (DDR4_A2, DDR4_B2)

5 CPU Fan Connector (CPU_FAN1)

6 CPU/Water Pump Fan Connector (CPU_FAN2/WP)

7 RGB LED Header (RGB_LED2)

8 Addressable LED Header (ADDR_LED2)

9 Post Status Checker (PSC)

10 ATX Power Connector (ATXPWR1)

11 USB 3.2 Gen1 Header (USB3_3_4)

12 Chassis/Water Pump Fan Connector (CHA_FAN1/WP)

13 SATA3 Connector (SATA3_1)

14 SATA3 Connector (SATA3_0)

15 SATA3 Connector (SATA3_3)

16 SATA3 Connector (SATA3_2)

17 Chassis/Water Pump Fan Connector (CHA_FAN4/WP)

18 SPI TPM Header (SPI_TPM_J1)

19 Power LED and Speaker Header (SPK_PLED1)

20 SATA3 Connector (SATA3_5)

21 SATA3 Connector (SATA3_4)

22 System Panel Header (PANEL1)

23 Chassis/Water Pump Fan Connector (CHA_FAN3/WP)

24 USB 3.2 Gen1 Header (USB3_5_6)

25 USB 2.0 Header (USB_5_6)

26 USB 2.0 Header (USB_3_4)

27 Addressable LED Header (ADDR_LED1)

28 RGB LED Header (RGB_LED1)

29 Front Panel Audio Header (HD_AUDIO1)

30 Clear CMOS Jumper (CLRMOS1)

31 underbolt AIC Connector (TB1)

32 Chassis/Water Pump Fan Connector (CHA_FAN2/WP)

2

I/O Panel

1

H470 Phantom Gaming 4

4

2

3

5

12

10

9

811

7

6

No. Description No. Description

1 USB 2.0 Ports (USB_1_2) 7 USB 3.2 Gen1 Ports (USB3_1_2)

2 USB 3.2 Gen2 Type-A Port (USB31_TA_1) 8 USB 3.2 Gen2 Type-C Port (USB31_TC_1)

3 LAN RJ-45 Port* 9 Antenna Bracket

4 Line In (Light Blue)** 10 DisplayPort 1.4

5 Front Speaker (Lime)** 11 HDMI Port

6 Microphone (Pink)** 12 PS/2 Mouse/Keyboard Port

* ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.

ACT/LINK LED

SPEED LED

LAN Por t

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection

** Function of the Audio Ports in 7.1-channel Conguration:

Port Function

Light Blue (Rear panel) Rear Speaker Out
Lime (Rear panel) Front Speaker Out
Pink (Rear panel) Central /Subwoofer Speaker Out
Lime (Front panel) Side Speaker Out

English

3

Chapter 1 Introduction

ank you for purchasing ASRock H470 Phantom Gaming 4 motherboard, a
reliable motherboard produced under ASRock’s consistently stringent quality
control. It delivers excellent performance with robust design conforming to
ASRock’s commitment to quality and endurance.

Becau se the motherboard specications and the BIOS soware might be updated, the
content of this documentation will be subject to change without notice. In case any
modications of this documentation occur, the updated version will be available on
ASRock’s website without further notice. If you require technical support related to
this motherboard, please vi sit our website for s pecic information about the model
you are using. You may nd the l atest VGA cards and CPU suppor t list on ASRock’s
website a s well. ASRock website http://www.asrock.com.

1.1 Package Contents

ASRock H470 Phantom Gaming 4 Motherboard (ATX Form Factor)

•

ASRock H470 Phantom Gaming 4 Quick Installation Guide

•

ASRock H470 Phantom Gaming 4 Support CD

•

2 x Serial ATA (SATA) Data Cables (Optional)

•

3 x Screws for M.2 Sockets (Optional)

•

1 x I/O Panel Shield

•

English

4

1.2 Specications

Platform

CPU

Chipset

Memory

* Please refer to Memory Support List on ASRock's website for
more information. (http://www.asrock.com/)
* CoreTM (i9/i7) support DDR4 up to 2933; CoreTM (i5/i3),
Pentium® and Celeron® support DDR4 up to 2666.

H470 Phantom Gaming 4

ATX Form Factor

•

Solid Capacitor design

•

Suppor ts 10th Gen Intel® CoreTM Processors (Socket 1200)

•

Digi Power design

•

10 Power Phase design

•

Supports Intel® Turbo Boost Max 3.0 Technology

•

Intel® H470

•

Dual Channel DDR4 Memory Technology

•

4 x DDR4 DIMM Slots

•

Supports DDR4 2933/2800/2666/2400/2133 non-ECC, un-

•

buered memory

Supports ECC UDIMM memory modules (operate in non-

•

ECC mode)
Max. capacity of system memory: 128GB

•

Supports Intel® Extreme Memory Prole (XMP) 2.0

•

15μ Gold Contact in DIMM Slots

•

Expansion
Slot

2 x PCI Express 3.0 x16 Slots (PCIE2/PCIE4: single at x16

•

(PCIE2); dual at x16 (PCIE2) / x4 (PCIE4)*

* Supports NVMe SSD as boot disks

3 x PCI Express 3.0 x1 Slots

•

Supports AMD Quad CrossFireXTM and CrossFireX

•

1 x M.2 Socket (Key E), supports type 2230 WiFi/BT module

•

and Intel® CNVi (Integrated WiFi/BT)

TM

English

5

Graphics

* Intel® UHD Graphics Built-in Visuals and the VGA outputs can
be supported only with processors which are GPU integrated.

Hardware Accelerated Codecs: AVC/H.264, HEVC/H.265

•

8bit, HEVC/H.265 10bit, VP8, VP9 8bit, VP9 10bit, MPEG 2,

MJPEG, VC-1
* VP9 10bit and VC-1 are for decode only.
* VP8 and VP9 encode are not supported by Windows OS.

Graphics, Media & Compute: Microso DirectX 12, OpenGL

•

4.5, Intel® Built In Visuals, Intel® Quick Sync Video, Hybrid /

Switchable Graphics, OpenCL 2.1

Display & Content Security: Rec. 2020 (Wide Color Gamut),

•

Microso PlayReady 3.0, Intel® SGX Content Protection,

UHD/HDR Blu-ray Disc

Dual graphics output: support HDMI and DisplayPort 1.4

•

ports by independent display controllers

Supports HDMI 1.4 with max. resolution up to 4K x 2K

•

(4096x2160) @ 30Hz

Supports DisplayPort 1.4 with max. resolution up to 4K x 2K

•

(4096x2304) @ 60Hz

Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and

•

HBR (High Bit Rate Audio) with HDMI 1.4 Port
(Compliant HDMI monitor is required)

Supports HDCP 2.3 with HDMI 1.4 and DisplayPort 1.4

•

Ports

Supports 4K Ultra HD (UHD) playback with HDMI 1.4 and

•

DisplayPort 1.4 Ports

English

6

Audio

7.1 CH HD Audio with Content Protection (Realtek ALC1200

•

Audio Codec)

Premium Blu-ray Audio support

•

Supports Surge Protection

•

PCB Isolate Shielding

•

Individual PCB Layers for R/L Audio Channel

•

Nahimic Audio

•

LAN

Rear Panel
I/O

H470 Phantom Gaming 4

Gigabit LAN 10/100/1000 Mb/s

•

Giga PHY Intel® I219V

•

Supports Wake-On-LAN

•

Supports Lightning/ESD Protection

•

Supports Energy Ecient Ethernet 802.3az

•

Supports PXE

•

1 x Antenna Bracket

•

1 x PS/2 Mouse/Keyboard Port

•

1 x HDMI Port

•

1 x DisplayPort 1.4

•

1 x USB 3.2 Gen2 Type-A Port (10 Gb/s) (ReDriver) (Supports

•

ESD Protection)
1 x USB 3.2 Gen2 Type-C Port (10 Gb/s) (ReDriver) (Supports

•

ESD Protection)
2 x USB 3.2 Gen1 Ports (Supports ESD Protection)

•

2 x USB 2.0 Ports (Supports ESD Protection)

•

1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

•

LED)
HD Audio Jacks: Line in / Front Speaker / Microphone

•

Storage

6 x SATA3 6.0 Gb/s Connectors, support RAID (RAID 0,

•

RAID 1, RAID 5, RAID 10, Intel Rapid Storage Technology

17), NCQ, AHCI and Hot Plug*
* If M2_1 is occupied by a SATA-type M.2 device, SATA3_5 will
be disabled.
* If M2_2 is occupied by a SATA-type M.2 device, SATA3_1 will
be disabled.
* If M2_2 is occupied by a PCIe-type M.2 device, SATA3_0 will
be disabled.

1 x Ultra M.2 Socket (M2_1), supports M Key type 2260/2280

•

M.2 SATA3 6.0 Gb/s module and M.2 PCI Express module
up to Gen3 x4 (32 Gb/s)**
1 x Ultra M.2 Socket (M2_2), supports M Key type

•

2260/2280/22110 M.2 SATA3 6.0 Gb/s module and M.2 PCI

Express module up to Gen3 x4 (32 Gb/s)**
** Supports Intel® OptaneTM Tech nolo gy
** Supports NVMe SSD as boot disks
** Supports ASRock U.2 Kit

English

7

Connector

1 x SPI TPM Header

•

1 x Power LED and Speaker Header

•

2 x RGB LED Headers

•

* Support in total up to 12V/3A, 36W LED Strip

2 x Addressable LED Headers

•

* Support in total up to 5V/3A, 15W LED Strip

1 x CPU Fan Connector (4-pin)

•

* e CPU Fan Connector supports the CPU fan of maximum
1A (12W) fan power.

1 x CPU/Water Pump Fan Connector (4-pin) (Smart Fan

•

Speed Control)
* e CPU/Water Pump Fan supports the water cooler fan of
maximum 2A (24W) fan power.

4 x Chassis/Water Pump Fan Connectors (4-pin) (Smart Fan

•

Speed Control)
* e Chassis/Water Pump Fan supports the water cooler fan of
maximum 2A (24W) fan power.
* CPU_FAN2/WP, CHA_FAN1/WP, CHA_FAN2/WP, CHA_
FAN3/WP and CHA_FAN4/WP can auto detect if 3-pin or 4-pin
fan is in use.

1 x 24 pin ATX Power Connector

•

1 x 8 pin 12V Power Connector

•

1 x 4 pin 12V Power Connector

•

1 x Front Panel Audio Connector

•

1 x underbolt AIC Connector (5-pin) (Supports ASRock

•

underbolt 3 AIC R2.0 Card only)

2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports

•

ESD Protection)

2 x USB 3.2 Gen1 Headers (Support 4 USB 3.2 Gen1 ports)

•

(Supports ESD Protection)

English

8

BIOS
Feature

AMI UEFI Legal BIOS with multilingual GUI support

•

ACPI 6.0 Compliant wake up events

•

SMBIOS 2.7 Support

•

CPU Core/Cache, GT, DRAM, PCH, VCCIO, VCCST,

•

VCCSA Voltage Multi-adjustment

Temperature Sensing: CPU, CPU/Water Pump, Chassis/Wa-

Hardware
Monitor

•

ter Pump Fans
Fan Tachometer: CPU, CPU/Water Pump, Chassis/Water

•

Pump Fans
Quiet Fan (Auto adjust chassis fan speed by CPU tempera-

•

ture): CPU, CPU/Water Pump, Chassis/Water Pump Fans
Fan Multi-Speed Control: CPU, CPU/Water Pump, Chassis/

•

Water Pump Fans
Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, DRAM,

•

VPPM, PCH, VCCSA, VCCST, VCCIO

Microso® Windows® 10 64-bit

OS

Certica­tions

* For detailed product information, please visit our website: http://www.asrock .com

Please realize that the re is a certain risk involved with overclocking, including
adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using
third-party overclocking tool s. Overclocking may aect your system’s stability, or
even cause damage to the components and devices of your system. It should be done
at your own risk and expense. We are not responsible for possible damage caused by
overclocking.

•

FCC, CE

•

ErP/EuP ready (ErP/EuP ready power supply is required)

•

H470 Phantom Gaming 4

English

9

Chapter 2 Installation

is is an ATX form factor motherboard. Before you install the motherboard, study
the conguration of your chassis to ensure that the motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components
or change any motherboard settings.

Make sure to unplug the power cord before installing or removing the motherboard

•

components. Failure to do so may cause physical injuries and damages to motherboard
components.
In order to avoid damage from static electricity to the motherboard’s components,

•

NEVER place your motherboard directly on a carpet. Also remember to use a grounded
wrist strap or touch a safety grounded object before you handle the components.
Hold components by the edges and do not touch the ICs.

•

Whenever you uninstall any components, place them on a grounded anti-static pad or

•

in the bag that comes with the components.
When placing screws to secure the motherboard to the chassis, please do not over-

•

tighten the screws! Doing so may damage the motherboard.

English

10

2.1 Installing the CPU

1

1. Before you insert the 1200-Pin CPU into the socket, please check if the PnP cap is on the
socket, if the CPU surface is unclean, or if there are any bent pins in the socket. Do not
force to in sert the CPU into the socket if above situation is found. Otherwise, the CPU
will be seriously damaged.

2. Unplug all power cables before installing the CPU.

H470 Phantom Gaming 4

A

B

2

11

English

3

5

4

English

12

H470 Phantom Gaming 4

Please save and replace the cover if the processor i s removed. e cover must be placed if
you wish to return the motherboard for aer service.

13

English

2.2 Installing the CPU Fan and Heatsink

1 2

English

14

CPU_FAN

H470 Phantom Gaming 4

2.3 Installing Memory Modules (DIMM)

is motherboard provides four 288-pin DDR4 (Double Data Rate 4) DIMM slots,
and supports Dual Channel Memory Technology.

1. For dual channel conguration, you always need to install identical (the same

brand, speed , size and chip-type) DDR4 DIMM pairs.

2. It is unable to activate Dual Channel Me mory Technology w ith only one or three

memory module installed.

3. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4

slot; otherwise, this motherboard and DIMM may be damaged.

Dual Channel Memory Conguration

Priority DDR4_A1 DDR4_A2 DDR4_B1 DDR4_B2

1 Populated Populated
2 Populated Populated Populated Populated

e DIMM only ts in one correct orientation. It will cause permanent damage to
the mothe rboard and the DIMM if you force the DIMM into the slot at incor rect
orientation.

15

English

1

2

English

16

3

H470 Phantom Gaming 4

2.4 Expansion Slots (PCI Express Slots)

ere are 5 PCI Express slots on the motherboard.

Before installing an ex pansion card, please make sure that the power supply is
switched o or the power cord is unplugged. Plea se read the documentation of the
expan sion card and make necessary hardware settings for the card before you start
the installation.

PCIe slots:

PCIE1 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIE2 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards.
PCIE3 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIE4 (PCIe 3.0 x16 slot) is used for PCI Express x4 lane width graphics cards.
PCIE5 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.

PCIe Slot Congurations

PCIE2 PCIE4

Single Graphics Card x16 N/A

Two Graphics Cards in

CrossFireXTM Mode

For a better ther mal environment, please connect a chassi s fan to the motherboard’s
chassis fan connector (CHA_ FAN1/WP, CHA_ FA N2/WP, CHA_FAN3/WP or
CHA_ FAN4/WP) when using multiple graphics cards.

x16 x4

English

17

2.5 Jumpers Setup

e illustration shows how jumpers are setup. When the jumper cap is placed on
the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is

“Open”.

Clear CMOS Jumper
(CLRMO S1)
(see p.1, No. 30)

CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system
parameters to default setup, please turn o the computer and unplug the power
cord from the power supply. Aer waiting for 15 seconds, use a jumper cap to
short the pins on CLRMOS1 for 5 seconds. However, please do not clear the
CMOS right aer you update the BIOS. If you need to clear the CMOS when you
just nish updating the BIOS, you must boot up the system rst, and then shut it
down before you do the clear-CMOS action. Please be noted that the password,
date, time, and user default prole will be cleared only if the CMOS battery is
removed. Please remember toremove the jumper cap aer clearing the CMOS.

2-pin Jumper

English

18

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over
these headers and connectors. Placing jumper caps over the headers and connectors
will cause permanent damage to the motherboard.

H470 Phantom Gaming 4

System Panel Header
(9-pi n PANEL1)
(see p.1, No. 22)

PWRBTN (Power Button):

Connec t to the power button on the chassis front panel. You may congure the way to
turn o your system using the power button.

RESET (Reset Button):
Connec t to the reset button on the chassi s front panel. Press the reset button to
restar t the computer if the computer freezes and fails to perform a nor mal restart.

PLED (Syste m Power LED):
Connec t to the power status indicator on the chassis front panel. e LED i s on when
the system is ope rating. e LED keeps blinking when the system i s in S1/S3 sleep
state. e LED is o when the system is in S4 sleep state or powered o (S5).

HDLED (Ha rd Drive Activity LED):
Connec t to the hard drive activity LED on the chassis front panel. e LED is on
when the hard drive i s reading or writing data.

e front panel design may dier by chassis. A front panel module mainly consists
of power button, reset button, power LED, hard drive activity LED, speaker and etc.
When connecting your chassis front panel module to this head er, make sure the wire
assig nments and the pin assig nments are matched correctly.

1

PLED+

PLED-

HDLED-

HDLED+

PWRBTN#

GND

RESET#

GND

GND

Connect the power button,
reset button and system
status indicator on the
chassis to this header
according to the pin
assignments below. Note
the positive and negative
pins before connecting the
cables.

19

English

Power LED and Speaker

PLED-

Header
(7-pin SPK_PLED1)
(see p.1, No. 19)

DUMMY
+5V

1

PLED+

SPEAKER

DUMMY

PLED+

Please connect the
chassis power LED and
the chassis speaker to this
header.

Serial ATA3 Connectors
(SATA3_0:
see p.1, No. 14)
(SATA3_1:
see p.1, No. 13)
(SATA3_2:
see p.1, No. 16)
(SATA3_3:
see p.1, No. 15)
(SATA3_4:
see p.1, No. 21)
(SATA3_5:
see p.1, No. 20)

USB 2.0 Headers
(9-pin USB_3_4)
(see p.1, No. 26)
(9-pin USB_5_6)
(see p.1, No. 25)

SATA3_0

SATA3_2

SATA3_4

USB_PWR

P-

1

P-

USB_PWR

SATA3_5

P+

GND

GND

P+

DUMMY

ese six SATA3
connectors support SATA
data cables for internal
storage devices with up to

SATA3_1

6.0 Gb/s data transfer rate.

* If M2_1 is occupied by
a SATA-type M.2 device,

SATA3_3

SATA3_5 will be disabled.
* If M2_2 is occupied by
a SATA-type M.2 device,
SATA3_1 will be disabled.
* If M2_2 is occupied by
a PCIe-type M.2 device,
SATA3_0 will be disabled.

ere are two USB

2.0 headers on this
motherboard. Each USB

2.0 header can support two
ports.

English

20

H470 Phantom Gaming 4

USB 3.2 Gen1 Headers
(19-pin USB3_3_4)
(see p.1, No. 11)
(19-pin USB3_5_6)
(see p.1, No. 24)

Front Panel Audio Header
(9-pin HD_ AUDIO1)
(see p.1, No. 29)

1. High Denition Audio support s Jack Sensing, but the panel wire on the chassis

must support HDA to function correctly. Please follow the instructions in our
manual and chassis manual to install your system.

2. If you use an AC’97 audio panel, please install it to the front panel audio header by

the steps below:
A. Connect Mic_IN (MIC) to MIC2_ L.
B. Conne ct Audio_R (RIN) to OUT2_R and Audio_ L (LIN) to OUT2_ L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_ RET and OUT_RET are for the HD audio panel only. You don’t need to
connect them for the AC’97 audio panel.
E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel
and adjust “Recording Volume”.

Vbus

IntA_PA_SSRX-

IntA_PA_SSRX+

GND

IntA_PA_SSTX-

IntA_PA_SSTX+

GND

IntA_PA_D-

IntA_PA_D+

IntA_PA_D+

IntA_PA_D-

GND

1

Dummy

IntA_PB_D+

IntA_PB_D-

GND

1

MIC2_L

1

IntA_PA_SSTX+

IntA_PA_SSTX-

GND

GND

IntA_PB_SSTX+

IntA_PB_SSTX-

PRESENCE#

MIC_RET

J_SENSE

OUT2_R

MIC2_R

VbusVbus

IntA_PB_SSRX-

IntA_PB_SSRX+

GND

IntA_PB_SSTX-

IntA_PB_SSTX+

GND

IntA_PB_D-

IntA_PB_D+

Dummy

IntA_PA_SSRX+

IntA_PA_SSRX-

Vbus

GND

IntA_PB_SSRX+

IntA_PB_SSRX-

VbusVbus

OUT_RET

OUT2_L

ere are two headers on
this motherboard. Each
USB 3.2 Gen1 header can
support two ports.

is header is for
connecting audio devices
to the front audio panel.

21

English

Chassis/Water Pump Fan

GND

FAN _SPEED_CONTROL

4 3 2 1

GND

FAN_VOLTAGE

Connectors
(4-pin CHA_FAN1/WP)
(see p.1, No. 12)

(4-pin CHA_FAN2/WP)
(see p.1, No. 32)

(4-pin CHA_FAN3/WP)
(see p.1, No. 23)

(4-pin CHA_FAN4/WP)
(see p.1, No. 17)

1

2

FAN_VOLTAGE
CHA_FAN_SPEED

3

4

FAN_SPEED_CONTROL

CHA_FAN_SPEED

FAN_VOLTAGE

FAN_SPEED_CONTROL

CHA_FAN_SPEED

FAN_VOLTAGE

1

2

FAN_VOLTAGE
CHA_FAN_SPEED

3

4

FAN_SPEED_CONTROL

GND

is motherboard provides
four 4-Pin water cooling
chassis fan connectors. If
you plan to connect a 3-Pin
chassis water cooler fan,

4
3

please connect it to Pin 1-3.

2
1

GND

English

CPU Fan Connector
(4-pin CPU_FAN1)
(see p.1, No. 5)

CPU/Water Pump Fan
Connector
(4-pin CPU_FAN2/WP)
(see p.1, No. 6)

ATX Power Connector
(24-pin ATXPWR1)
(see p.1, No. 10)

CPU_FAN_SPEED

GND

1 2 3 4

FAN_VOLTAGE

CPU_FAN_SPEED

GND

1 2 3 4

12

1

FAN_SPEED_CONTROL

FAN_SPEED_CONTROL

24

13

is motherboard provides
a 4-Pin CPU fan (Quiet
Fan) connector. If you plan
to connect a 3-Pin CPU
fan, please connect it to Pin
1-3.

is motherboard provides
a 4-Pin water cooling CPU
fan connector. If you plan
to connect a 3-Pin CPU
water cooler fan, please
connect it to Pin 1-3.

is motherboard provides
a 24-pin ATX power con­nector. To use a 20-pin
ATX power supply, please
plug it along Pin 1 and Pin

13.

22

H470 Phantom Gaming 4

1

ATX 12V Power
Connector
(8-pin ATX12V1)
(see p.1, No. 1)

ATX 12V Power
Connector
(4-pin ATX12V2)
(see p.1, No. 2)

SPI TPM Header
(13 -pi n SPI_TPM _J1)
(see p.1, No. 18)

8 5

4

SPI_DQ3

+3.3V

TPM_Present

CLK

1

RSMRST#

SPI_MISO

SPI_CS0

SPI_DQ2

SPI_MOSI

RST#

TPM_PIRQ

SPI_TPM_CS#

GND

is motherboard provides
an 8-pin ATX 12V power
connector. To use a 4-pin
ATX power supply, please
plug it along Pin 1 and Pin

5.

Please connect

an ATX 12V
power supply to this con­nector.

*Connecting an ATX 12V

4-pin cable here is optional.

*The power supply plug fits
into this connec-tor in only
one orientation.

is connector supports SPI
Trusted Platform Module (TPM)
system, which can securely
store keys, digital certicates,
passwords, and data. A TPM
system also helps enhance
network security, protects digital
identities, and ensures platform
integrity.

underbolt AIC
Connector
(5-pin TB1)
(see p.1, No. 31)

1

Please connect a
underbolt™ add-in card
(AIC) to this connector
via the GPIO cable.
*Please install the underbolt™
AIC card to PCIE4 (default slot).

English

23

RGB LED Headers
(4-pin RGB_LED1)
(see p.1, No. 28)

(4-pi n RGB _LED2)
(see p.1, No. 7)

1

12V GR B

B

R

G

12V

1

RGB headers are used to connect
RGB LED extension cables which
allow users to choose from
various LED lighting eects.

Caution: Never install the

RGB LED cable in the wrong

orientation; otherwise, the cable

may be damaged.

*Please refer to page 36 for further
instructions on this header.

English

Addressable LED Headers
(3-pin A DDR_LED1)
(see p.1, No. 27)

(3-pin A DDR_LED2)
(see p.1, No. 8)

1

VOUT

DO_ADDR

GND

ese headers are used to connect
Addressable

LED extension cables
which allow users to choose from
various LED lighting
eects.

Caution: Never install the Ad-

dressable LED cable in the wrong

orientation; otherwise, the cable

may be damaged.

*Please refer to page 37 for
further instructions on this
header.

24

H470 Phantom Gaming 4

2.7 Post Status Checker

Post Status Checker (PSC) diagnoses the computer when users power on the
machine. It emits a red light to indicate whether the CPU, memory, VGA or stor­age is dysfunctional. e lights go o if the four mentioned above are functioning
normally.

25

English

2.8 M.2 WiFi/BT Module and Intel® CNVi (Integrated WiFi/BT)
Installation Guide

e M.2, also known as the Next Generation Form Factor (NGFF), is a small size and
versatile card edge connector that aims to replace mPCIe and mSATA. e M.2 Socket (Key
E) supports type 2230 WiFi/BT module and Intel® CNVi (Integrated WiFi/BT).
* e M.2 socket does not support SATA M.2 SSDs.

Before you install Intel® Integrated Connectivity (CNVi) module, be sure to turn o the AC
power.

Installing the WiFi/BT module

Step 1

Prepare a type 2230 WiFi/BT module
or Intel® CNVi (Integrated WiFi/BT)
and the screw.

Step 2

Find the nut location to be used.

English

26

PCB Length: 3cm
Module Type: Type2230

A

H470 Phantom Gaming 4

Step 3

Gently insert the WiFi/BT module
or Intel® CNVi (Integrated WiFi/
BT) into the M.2 slot. Please be
aware that the module only ts in one

A

o

A

20

A

orientation.

Step 4

Tighten the screw with a screwdriver
to secure the module into place.
Please do not overtighten the screw as
this might damage the module.

27

English

2.9 M.2_SSD (NGFF) Module Installation Guide (M2_1)

e M.2, also known as the Next Generation Form Factor (NGFF), is a small size and
versatile card edge connector that aims to replace mPCIe and mSATA. e Ultra M.2
Socket (M2_1) supports M Key type 2260/2280 M.2 SATA3 6.0 Gb/s module and M.2 PCI
Express module up to Gen3 x4 (32 Gb/s).

* If M2_1 is occupied by a SATA-type M.2 device, SATA3_5 will be disabled.

Installing the M.2_SSD (NGFF) Module

Step 1

Prepare a M.2_SSD (NGFF) module
and the screw.

English

2

1

AB

No. 1 2

Nut Location A B

PCB Length 6cm 8cm

Module Type Typ e2260 Type 228 0

Step 2

Depending on the PCB type and
length of your M.2_SSD (NGFF)
module, nd the corresponding nut
location to be used.

28