Asrock H410M-HDV R2.0 User Manual

Version 1.0
Published November 2020
Copyright©2020 ASRock INC. All rights reserved.

Copyright Notice:

No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.

Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of prots, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”

ASRock Website: http://www.asrock.com

AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage caused by our
goods. You are also entitled to have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not amount to a major failure. If
you require assistance please call ASRock Tel : [phone] ext.123 (Standard
International call charges apply)

e terms HDMI® and HDMI High-Denition Multimedia Interface, and the
HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.

Contents

Chapter 1 Introduction 1

1.1 Package Contents 1

1.2 Specications 2

1.3 Motherboard Layout 6

1.4 I/O Panel 9

Chapter 2 Installation 11

2.1 Installing the CPU 12

2.2 Installing the CPU Fan and Heatsink 15

2.3 Installing Memory Modules (DIMM) 16

2.4 Expansion Slots (PCI Express Slots) 18

2.5 Jumpers Setup 19

2.6 Onboard Headers and Connectors 20

Chapter 3 Software and Utilities Operation 24

3.1 Installing Drivers 24

3.2 ASRock Motherboard Utility (A-Tuning) 25

3.2.1 Installing ASRock Motherboard Utility (A-Tuning) 25

3.2.2 Using ASRock Motherboard Utility (A-Tuning) 25

3.3 ASRock Live Update & APP Shop 28

3.3.1 UI Overview 28

3.3.2 Apps 29

3.3.3 BIOS & Drivers 32

3.3.4 Setting 33

Chapter 4 UEFI SETUP UTILITY 34

4.1 Introduction 34

4.2 EZ Mode 35

4.3 Advanced Mode 36

4.3.1 UEFI Menu Bar 36

4.3.2 Navigation Keys 37

4.4 Main Screen 38

4.5 OC Tweaker Screen 40

4.6 Advanced Screen 48

4.6.1 CPU Conguration 49

4.6.2 Chipset Conguration 51

4.6.3 Storage Conguration 54

4.6.4 Super IO Conguration 55

4.6.5 ACPI Conguration 56

4.6.6 USB Conguration 57

4.6.7 Trusted Computing 58

4.7 Tools 59

4.8 Hardware Health Event Monitoring Screen 61

4.9 Security Screen 63

4.10 Boot Screen 64

4.11 Exit Screen 67

H410M-HDV R2.0
H410M-HVS R2.0

Chapter 1 Introduction

ank you for purchasing ASRock H410M-HDV R2.0 / H410M-HVS R2.0
motherboard, a reliable motherboard produced under ASRock’s consistently
stringent quality control. It delivers excellent performance with robust design
conforming to ASRock’s commitment to quality and endurance.

In this documentation, Chapter 1 and 2 contains the introduction of the
motherboard and step-by-step installation guides. Chapter 3 contains the operation
guide of the soware and utilities. Chapter 4 contains the conguration guide of
the BIOS setup.

Becau se the motherboard specications and the BIOS soware might be updated, the
content of this documentation will be subject to change without notice. In case any
modications of this documentation occur, the updated version will be available on
ASRock’s website w ithout f urther notice. If you require technical support relate d to
this motherboard, please vi sit our website for s pecic information about the model
you are using. You may nd the l atest VGA cards and CPU suppor t list on ASRock’s
website a s well. ASRock website ht tp://www.a srock.com.

1.1 Package Contents

ASRock H410M-HDV R2.0 / H410M-HVS R2.0 Motherboard (Micro ATX Form

•

Factor)
ASRock H410M-HDV R2.0 / H410M-HVS R2.0 Quick Installation Guide

•

ASRock H410M-HDV R2.0 / H410M-HVS R2.0 Support CD

•

2 x Serial ATA (SATA) Data Cables (Optional)

•

1 x I/O Panel Shield

•

English

1

1.2 Specications

Platform

CPU

Chipset

Memory

•

•

•

•

•

•

•

•

•

•

* Please refer to Memory Support List on ASRock's website for
more information. (http://www.asrock.com/)
* CoreTM (i9/i7) support DDR4 up to 2933; CoreTM (i5/i3),
Pentium® and Celeron® support DDR4 up to 2666.

•

•

•

•

Micro ATX Form Factor
Solid Capacitor design

Supports 10th Gen Intel® CoreTM Processors (Socket 1200)
Digi Power design
5 Power Phase design
Supports Intel® Turbo Boost Max 3.0 Technology

Intel® H410

Dual Channel DDR4 Memory Technology
2 x DDR4 DIMM Slots
Supports DDR4 2933/2800/2666/2400/2133 non-ECC, un­buered memory

Supports ECC UDIMM memory modules (operate in non­ECC mode)
Max. capacity of system memory: 64GB
Supports Intel® Extreme Memory Prole (XMP) 2.0
15μ Gold Contact in DIMM Slots

English

2

Expansion
Slot

Graphics

1 x PCI Express 3.0 x16 Slot

•

* Supports NVMe SSD as boot disks

1 x PCI Express 3.0 x1 Slot

•

Intel® UHD Graphics Built-in Visuals and the VGA outputs

•

can be supported only with processors which are GPU
integrated.
Hardware Accelerated Codecs: AVC/H.264, HEVC/H.265

•

8bit, HEVC/H.265 10bit, VP8, VP9 8bit, VP9 10bit, MPEG 2,

MJPEG, VC-1
* VP9 10bit and VC-1 are for decode only.
* VP8 and VP9 encode are not supported by Windows OS.

Graphics, Media & Compute: Microso DirectX 12, OpenGL

•

4.5, Intel® Built In Visuals, Intel® Quick Sync Video, Hybrid /
Switchable Graphics, OpenCL 2.1
Display & Content Security: Rec. 2020 (Wide Color Gamut),

•

Microso PlayReady 3.0, Intel® SGX Content Protection,
UHD/HDR Blu-ray Disc

H410M-HDV R2.0:

ree graphics output options: D-Sub, DVI-D and HDMI

•

* Supports up to 2 displays simultaneously

Supports HDMI 1.4 with max. resolution up to 4K x 2K

•

(4096x2160) @ 30Hz
Supports DVI-D with max. resolution up to 1920x1200 @

•

60Hz
Supports D-Sub with max. resolution up to 1920x1200 @

•

60Hz
Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and

•

HBR (High Bit Rate Audio) with HDMI 1.4 Port (Compliant
HDMI monitor is required)
Supports HDCP 2.3 with DVI-D and HDMI 1.4 Ports

•

Supports 4K Ultra HD (UHD) playback with HDMI 1.4 Port

•

H410M-HVS R2.0:

Dual graphics output: support HDMI and D-Sub ports by

•

independent display controllers
Supports HDMI 1.4 with max. resolution up to 4K x 2K

•

(4096x2160) @ 30Hz
Supports D-Sub with max. resolution up to 1920x1200 @

•

60Hz
Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and

•

HBR (High Bit Rate Audio) with HDMI 1.4 Port (Compliant
HDMI monitor is required)
Supports HDCP 2.3 with HDMI 1.4 Port

•

Supports 4K Ultra HD (UHD) playback with HDMI 1.4 Port

•

H410M-HDV R2.0
H410M-HVS R2.0

Audio

LAN

7.1 CH HD Audio (Realtek ALC887/897 Audio Codec)

•

Supports Surge Protection

•

Gigabit LAN 10/100/1000 Mb/s

•

Giga PHY Intel® I219V

•

Supports Wake-On-LAN

•

English

3

English

Rear Panel
I/O

Storage

Connector

Supports Lightning/ESD Protection

•

Supports Energy Ecient Ethernet 802.3az

•

Supports PXE

•

1 x PS/2 Mouse/Keyboard Port

•

4 x USB 2.0 Ports (Supports ESD Protection)

•

2 x USB 3.2 Gen1 Ports (Supports ESD Protection)

•

1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

•

LED)

HD Audio Jacks: Line in / Front Speaker / Microphone

•

H410M-HDV R2.0:

1 x D-Sub Port

•

1 x DVI-D Port

•

1 x HDMI Port

•

H410M-HVS R2.0:

1 x D-Sub Port

•

1 x HDMI Port

•

4 x SATA3 6.0 Gb/s Connectors, support NCQ, AHCI and

•

Hot Plug

1 x SPI TPM Header

•

1 x Chassis Intrusion and Speaker Header

•

1 x CPU Fan Connector (4-pin)

•

* e CPU Fan Connector supports the CPU fan of maximum
1A (12W) fan power.

1 x Chassis/Water Pump Fan Connector (4-pin) (Smart Fan

•

Speed Control)
* e Chassis/Water Pump Fan supports the water cooler fan of
maximum 2A (24W) fan power.
* CHA_FAN1/WP can auto detect if 3-pin or 4-pin fan is in use.

1 x 24 pin ATX Power Connector

•

1 x 8 pin 12V Power Connector

•

1 x Front Panel Audio Connector

•

1 x USB 2.0 Header (Supports 2 USB 2.0 ports) (Supports

•

ESD Protection)

1 x USB 3.2 Gen1 Header (Supports 2 USB 3.2 Gen1 ports)

•

(Supports ESD Protection)

4

BIOS
Feature

Hardware
Monitor

OS

Certica­tions

AMI UEFI Legal BIOS with multilingual GUI support

•

ACPI 6.0 Compliant wake up events

•

SMBIOS 2.7 Support

•

CPU Core/Cache, GT, DRAM, PCH +1.0V, VCCST Voltage

•

Multi-adjustment

Temperature Sensing: CPU, Chassis/Water Pump Fans

•

Fan Tachometer: CPU, Chassis/Water Pump Fans

•

Quiet Fan (Auto adjust chassis fan speed by CPU tempera-

•

ture): CPU, Chassis/Water Pump Fans
Fan Multi-Speed Control: CPU, Chassis/Water Pump Fans

•

CASE OPEN detection

•

Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, PCH

•

+1.0V

Microso® Windows® 10 64-bit

•

FCC, CE

•

ErP/EuP ready (ErP/EuP ready power supply is required)

•

H410M-HDV R2.0
H410M-HVS R2.0

* For detailed product information, please visit our website: http://ww w.asrock.com

Please realize that the re is a certain r isk involved with overclo cking, including
adjusting the setting in the BIOS, applying Untied Overclocking Technol ogy, or using
third-party overclocking tool s. Overclocking may aect your system’s stability, or
even cause dam age to the components and devices of your system. It should be done
at your own risk and expense. We are not responsible for poss ible damage caused by
overclocking.

English

5

1.3 Motherboard Layout

H410M-HDV R2.0:

English

6

H410M-HVS R2.0:

H410M-HDV R2.0
H410M-HVS R2.0

English

7

No. Description

1 ATX 12V Power Connector (ATX12V1)

2 Chassis/Water Pump Fan Connector (CHA_FAN1/WP)

3 CPU Fan Connector (CPU_FAN1)

4 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)

5 ATX Power Connector (ATXPWR1)

6 USB 3.2 Gen1 Header (USB3_3_4)

7 Clear CMOS Jumper (CLRMOS1)

8 USB 2.0 Header (USB_5_6)

9 SATA3 Connector (SATA3_0)

10 SATA3 Connector (SATA3_1)

11 SATA3 Connector (SATA3_2)

12 SATA3 Connector (SATA3_3)

13 SPI TPM Header (SPI_TPM_J1)

14 Chassis Intrusion and Speaker Header (SPK_CI1)

15 System Panel Header (PANEL1)

16 Front Panel Audio Header (HD_AUDIO1)

English

8

1.4 I/O Panel

H410M-HDV R2.0:

1

H410M-HDV R2.0
H410M-HVS R2.0

2

3

4

5

11

No. Description No. Description

1 D-Sub Port 7 USB 2.0 Ports (USB_34)

2 USB 2.0 Ports (USB_12) 8 USB 3.2 Gen1 Ports (USB3_12)

3 LAN RJ-45 Port* 9 PS/2 Mouse/Keyboard Port

4 Line In (Light Blue)** 10 HDMI Port

5 Front Speaker (Lime)** 11 DVI-D Port

6 Microphone (Pink)**

10 67

9

8

H410M-HVS R2.0:

1

10 67

No. Description No. Description

1 D-Sub Port 6 Microphone (Pink)**

2 USB 2.0 Ports (USB_12) 7 USB 2.0 Ports (USB_34)

3 LAN RJ-45 Port* 8 USB 3.2 Gen1 Ports (USB3_12)

4 Line In (Light Blue)** 9 PS/2 Mouse/Keyboard Port

5 Front Speaker (Lime)** 10 HDMI Port

2

9

8

3

4

5

English

9

* ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications .

ACT/LINK L ED

SPEED LE D

LAN Por t

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection

** Function of the Au dio Ports in 7.1-channel Con guration:

Port Function

Light Blue (Rear panel) Rear Speaker Out
Lime (Rear panel) Front Speaker Out
Pink (Rear panel) Central /Subwoofer Speaker Out
Lime (Front panel) Side Speaker Out

English

10

H410M-HDV R2.0
H410M-HVS R2.0

Chapter 2 Installation

is is a Micro ATX form factor motherboard. Before you install the motherboard,
study the conguration of your chassis to ensure that the motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components
or change any motherboard settings.

Make sure to unplug the power cord before installing or removing the motherboard

•

components. Failure to do so may cause physical injuries and damages to motherboard
components.
In order to avoid damage from static electricity to the motherboard’s components,

•

NEVER place your motherboard directly on a carpet. Also remember to use a grounded
wrist strap or touch a safety grounded object before you handle the components.
Hold components by the edges and do not touch the ICs.

•

Whenever you uninstall any components, place them on a grounded anti-static pad or

•

in the bag that comes with the components.
When placing screws to secure the motherboard to the chassis, please do not over-

•

tighten the screws! Doing so may damage the motherboard.

11

English

2.1 Installing the CPU

1. Before you insert the 120 0-Pin CPU into the socket, please check if the PnP ca p
is on the socket, if the CPU sur face is unclean, or if th ere are any b ent pins in the
socket. Do not force to insert the CPU into the socket if above situ ation is found.
Other wise, the CPU wil l be seriously d amaged.

2. Unplug all power cables be fore installing the CPU.

1

A

B

English

12

2

H410M-HDV R2.0
H410M-HVS R2.0

3

5

4

13

English

Please save and replace the cover if the processor i s removed. e cover must be
placed if you wish to return the motherboard for aer service.

English

14

2.2 Installing the CPU Fan and Heatsink

1 2

H410M-HDV R2.0
H410M-HVS R2.0

CPU_FAN

English

15

2.3 Installing Memory Modules (DIMM)

is motherboard provides two 288-pin DDR4 (Double Data Rate 4) DIMM slots,
and supports Dual Channel Memory Technology.

1. For dual channel conguration, you always need to install identica l (the same

brand, speed , size and chip-type) DDR4 DIMM pairs.

2. It is unable to activate Dual Channel Memor y Technology with only one memory
module instal led.

3. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4
slot; otherwise, this motherboard and DIMM may be damaged.

e DIMM only ts in one correct orie ntation. It will cause permanent dam age to
the mothe rboard and the DIMM if you force the DIMM into the slot at incor rect
orientation .

English

16

H410M-HDV R2.0
H410M-HVS R2.0

1

2

3

English

17

2.4 Expansion Slots (PCI Express Slots)

ere are 2 PCI Express slots on the motherboard.

Before installing an ex pansion card, please make sure that the power supply is
switched o or the power cord is unplugged. Plea se read the documentation of the
expan sion card and mak e necessary hardware settings for the card before you start
the installation.

PCIe slots:

PCIE1 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIE2 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards.

English

18