ASRock H370M Pro4 Service Manual

Version 1.0

Published March 2018

Copyright©2018 ASRock INC. All rights reserved.

Copyright Notice:

No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.

Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of prots, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see ww w.dtsc.ca.gov/hazardouswaste/
perchlorate”

ASRock Website: http://www.asrock.com

AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage caused by our goods. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. If you require assistance please call ASRock Tel
: [phone] ext.123 (Standard International call charges apply)

e terms HDMI™ and HDMI High-Denition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.

Contents

Chapter 1 Introduction 1

1.1 Package Contents 1

1.2 Specications 2

1.3 Motherboard Layout 7

1.4 I/O Panel 9

Chapter 2 Installation 11

2.1 Installing the CPU 12

2.2 Installing the CPU Fan and Heatsink 15

2.3 Installing Memory Modules (DIMM) 16

2.4 Expansion Slots (PCI Express Slots) 18

2.5 Jumpers Setup 19

2.6 Onboard Headers and Connectors 20

2.7 CrossFireXTM and Quad CrossFireXTM Operation Guide 24

2.7.1 Installing Two CrossFireXTM-Ready Graphics Cards 24

2.7.2 Driver Installation and Setup 26

2.8 M.2 WiFi/BT Module and Intel® CNVi (Integrated WiFi/BT)
Installation Guide 27

2.9 M.2_SSD (NGFF) Module Installation Guide (M2_1 and M2_2) 29

Chapter 3 Software and Utilities Operation 33

3.1 Installing Drivers 33

3.2 A-Tuning 34

3.3 ASRock Live Update & APP Shop 37

3.3.1 UI Overview 37

3.3.2 Apps 38

3.3.3 BIOS & Drivers 41

3.3.4 Setting 42

Chapter 4 UEFI SETUP UTILITY 43

4.1 Introduction 43

4.2 EZ Mode 44

4.3 Advanced Mode 45

4.3.1 UEFI Menu Bar 45

4.3.2 Navigation Keys 46

4.4 Main Screen 47

4.5 OC Tweaker Screen 48

4.6 Advanced Screen 58

4.6.1 CPU Conguration 59

4.6.2 Chipset Conguration 61

4.6.3 Storage Conguration 64

4.6.4 Super IO Conguration 65

4.6.5 ACPI Conguration 66

4.6.6 USB Conguration 68

4.6.7 Trusted Computing 69

4.7 Tools 70

4.8 Hardware Health Event Monitoring Screen 72

4.9 Security Screen 75

4.10 Boot Screen 76

4.11 Exit Screen 79

Chapter 1 Introduction

ank you for purchasing ASRock H370M Pro4 motherboard, a reliable

motherboard produced under ASRock’s consistently stringent quality control.

It delivers excellent performance with robust design conforming to ASRock’s

commitment to quality and endurance.

In this documentation, Chapter 1 and 2 contains the introduction of the

motherboard and step-by-step installation guides. Chapter 3 contains the operation

guide of the soware and utilities. Chapter 4 contains the conguration guide of

the BIOS setup.

Becau se the motherboard specications and the BIOS soware might be updated, the
content of this documentation will be subject to change without notice. In case any
modications of this documentation occur, the updated version will be available on
ASRock’s website w ithout f urther notice. If you require technical support relate d to
this motherboard, please vi sit our website for s pecic information about the model
you are using. You may nd the l atest VGA cards and CPU suppor t list on ASRock’s
website a s well. ASRock website ht tp://www.a srock.com.

1.1 Package Contents

ASRock H370M Pro4 Motherboard (Micro ATX Form Factor)

•

ASRock H370M Pro4 Quick Installation Guide

•

ASRock H370M Pro4 Support CD

•

2 x Serial ATA (SATA) Data Cables (Optional)

•

3 x Screws for M.2 Sockets (Optional)

•

1 x I/O Panel Shield

•

H370M Pro4

English

1

1.2 Specications

Platform

CPU

Chipset

Memory

•

•

•

•

•

•

•

•

•

•

•

•

•

•

Micro ATX Form Factor

Solid Capacitor design

Supports 8th Generation Intel® CoreTM Processors (Socket

1151)

Digi Power design

10 Power Phase design

Supports Intel® Turbo Boost 2.0 Technology

Intel® H370

Dual Channel DDR4 Memory Technology

4 x DDR4 DIMM Slots

Supports DDR4 2666/2400/2133 non-ECC, un-buered

memory

Supports ECC UDIMM memory modules (operate in non-

ECC mode)

Max. capacity of system memory: 64GB

Supports Intel® Extreme Memory Prole (XMP) 2.0

15μ Gold Contact in DIMM Slots

English

2

Expansion
Slot

2 x PCI Express 3.0 x16 Slots (PCIE1/PCIE4: single at x16

•

(PCIE1); dual at x16 (PCIE1) / x4 (PCIE4))

* If PCIE2 is occupied, PCIE4 will downgrade to x2 mode.

* Supports NVMe SSD as boot disks

2 x PCI Express 3.0 x1 Slots (Flexible PCIe)

•

Supports AMD Quad CrossFireXTM and CrossFireX

•

1 x M.2 Socket (Key E), supports ty pe 2230 WiFi/BT module

•

and Intel® CNVi (Integrated WiFi/BT)

TM

Graphics

Intel® UHD Graphics Built-in Visuals and the VGA outputs

•

can be supported only with processors which are GPU

integrated.

Supports Intel® UHD Graphics Built-in Visuals : Intel®

•

Quick Sync Video with AVC, MVC (S3D) and MPEG-2 Full

HW Encode1, Intel® InTruTM 3D, Intel® Clear Video HD

Technology, Intel® InsiderTM, Intel® UHD Graphics

DirectX 12

•

HWAEncode/Decode: AVC/H.264, HEVC/H.265 8-bit,

•

HEVC/H.265 10-bit, VP8, VP9 8-bit, VP9 10-bit (Decode

only), MPEG2, MJPEG, VC-1 (Decode only)

ree graphics output options: D-Sub, DVI-D and HDMI

•

Supports Triple Monitor

•

Supports HDMI with max. resolution up to 4K x 2K

•

(4096x2160) @ 30Hz

Supports DVI-D with ma x. resolution up to 1920x1200 @

•

60Hz

Supports D-Sub with max. resolution up to 1920x1200 @

•

60Hz

Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and

•

HBR (High Bit Rate Audio) with HDMI Port (Compliant

HDMI monitor is required)

Supports HDCP with DVI-D and HDMI Ports

•

Supports 4K Ultra HD (UHD) playback with HDMI Port

•

H370M Pro4

Audio

7.1 CH HD Audio with Content Protection (Realtek ALC892

•

Audio Codec)

* To congure 7.1 CH HD Audio, it is required to use an HD

front panel audio module and enable the multi-channel audio

feature through the audio driver.

Premium Blu-ray Audio support

•

Supports Surge Protection

•

ELNA Audio Caps

•

English

3

English

LAN

Rear Panel
I/O

Storage

Gigabit LAN 10/100/1000 Mb/s

•

Giga PHY Intel® I219V

•

Supports Wake-On-LAN

•

Supports Lightning/ESD Protection

•

Supports Energy Ecient Ethernet 802.3az

•

Supports PXE

•

1 x PS/2 Mouse Port

•

1 x PS/2 Keyboard Port

•

1 x D-Sub Port

•

1 x DVI-D Port

•

1 x HDMI Port

•

2 x USB 2.0 Ports (Supports ESD Protection)

•

1 x USB 3.1 Gen2 Type-A Port (10 Gb/s) (Supports ESD

•

Protection)

1 x USB 3.1 Gen2 Type-C Port (10 Gb/s) (Supports ESD

•

Protection)

2 x USB 3.1 Gen1 Ports (Supports ESD Protection)

•

1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

•

LED)

HD Audio Jacks: Line in / Front Speaker / Microphone

•

6 x SATA3 6.0 Gb/s Connectors, support RAID (RAID 0,

•

RAID 1, RAID 5, RAID 10, Intel Rapid Storage Technology

15), NCQ, AHCI and Hot Plug*

* If M2_2 is occupied by a SATA-type M.2 device, SATA3_1 will

be disabled.

1 x Ultra M.2 Socket (M2_1), supports M Key type

•

2230/2242/2260/2280 M.2 PCI Express module up to Gen3

x4 (32 Gb/s)**

1 x M.2 Socket (M2_2), supports M Key type

•

2230/2242/2260/2280 M.2 SATA3 6.0 Gb/s module and M.2

PCI Express module up to Gen3 x1 (8 Gb/s)**

** Supports Intel® OptaneTM Technology (M2 _1 only)

** Supports NVMe SSD as boot disks

** Supports ASRock U.2 Kit

4

Connector

1 x COM Port Header

•

1 x TPM Header

•

1 x Chassis Intrusion and Speaker Header

•

1 x CPU Fan Connector (4-pin)

•

* e CPU Fan Connector supports the CPU fan of ma ximum

1A (12W) fan power.

1 x CPU/Water Pump Fan Connector (4-pin) (Smart Fan

•

Speed Control)

* e CPU/Water Pump Fan supports the water cooler fan of

maximum 2A (24W) fan power.

2 x Chassis/Water Pump Fan Connectors (4-pin) (Smart Fan

•

Speed Control)

* e Chassis/Water Pump Fan supports the water cooler fan of

maximum 2A (24W) fan power.

* CPU_FAN2/WP, CHA_FAN1/WP and CHA_FAN2/WP can

auto detect if 3-pin or 4-pin fan is in use.

1 x 24 pin ATX Power Connector

•

1 x 8 pin 12V Power Connector

•

1 x Front Panel Audio Connector

•

2 x USB 2.0 Headers (Support 3 USB 2.0 ports) (Supports

•

ESD Protection)

2 x USB 3.1 Gen1 Headers (Support 4 USB 3.1 Gen1 ports)

•

(Supports ESD Protection)

H370M Pro4

BIOS
Feature

Hardware
Monitor

AMI UEFI Legal BIOS with multilingual GUI support

•

ACPI 6.0 Compliant wake up events

•

SMBIOS 2.7 Support

•

CPU, DRAM, PCH 1.0V, VCCIO, VCCSA, VCCST Voltage

•

Multi-adjustment

Temperature Sensing: CPU, CPU/Water Pump, Chassis/Wa-

•

ter Pump Fans

Fan Tachometer: CPU, CPU/Water Pump, Chassis/Water

•

Pump Fans

Quiet Fan (Auto adjust chassis fan speed by CPU tempera-

•

ture): CPU, CPU/Water Pump, Chassis/Water Pump Fans

Fan Multi-Speed Control: CPU, CPU/Water Pump, Chassis/

•

Water Pump Fans

English

5

CASE OPEN detection

•

Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, DRAM,

•

PCH 1.0V

Microso® Windows® 10 64-bit

OS

Certica­tions

* For detailed product information, please visit our website: http://ww w.asrock.com

Please realize that the re is a certain r isk involved with overclo cking, including
adjusting the setting in the BIOS, applying Untied Overclocking Technol ogy, or using
third-party overclocking tool s. Overclocking may aect your system’s stability, or
even cause dam age to the components and devices of your system. It should be done
at your own risk and expense. We are not responsible for poss ible damage caused by
overclocking.

•

FCC, CE

•

ErP/EuP Ready (ErP/EuP ready power supply is required)

•

English

6

1.3 Motherboard Layout

Intel

H370

ATXP WR 1

HDLED RE SET

PLED PWRBTN

PANEL1

1

COM1

1

H3 70 M Pro4

RoH S

PCI E1

TPMS1

1

1

SPK_CI1

1

PCI E2

CMO S

Bat ter y

DDR4 _A2 (64 bit, 288- pin modu le)

DDR4 _A1 (64 bit, 288- pin modu le)

DDR4 _B2 (64 bit, 288- pin modu le)

DDR4 _B1 (64 bit, 288- pin modu le)

ATX12V1

SATA3_2

SATA3_3

USB3_5_ 6

SATA3_4

SATA3_5

CLRMOS1

1

1

HD_AUDIO1

M2_1

Top:
RJ-4 5

HDMI 1

Top:

LINE IN

Center:

FRONT

Bottom:

MIC I N

USB 3.1 Gen2
T:USB 3_TA_1
B:U SB3_TC_ 1

PCI E4

USB 3. 1 G en2

SATA3_1

Ultr a M.2

PCIe Gen3 x4

PS2

Keybo ard

PS2

Mouse

DVI 1

VGA 1

USB 3.1 Gen1
T:US B3_3
B: USB3_4

USB3_4

1

M2_2

SATA3_0

PCI E3

1

USB3_7_ 8

USB 2.0
T:U SB1
B: USB2

USB5

1

M2_3

CPU_FAN1

CPU_FAN2/ WP

CHA_FAN2 /WP

CHA_FAN1 /WP

H370M Pro4

English

7

No. Description

1 ATX 12V Power Connector (ATX12V1)

2 CPU Fan Connector (CPU_FAN1)

3 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)

4 2 x 288-pin DDR4 DIMM Slots (DDR4_A2, DDR4_B2)

5 CPU/Water Pump Fan Connector (CPU_FAN2/WP)

6 ATX Power Connector (ATXPWR1)

7 USB 3.1 Gen1 Header (USB3_5_6)

8 SATA3 Connector (SATA3_0)

9 SATA3 Connector (SATA3_1)

10 Chassis/Water Pump Fan Connector (CHA_FAN2/WP)

11 USB 3.1 Gen1 Header (USB3_7_8)

12 SATA3 Connector (SATA3_2)

13 SATA3 Connector (SATA3_3)

14 SATA3 Connector (SATA3_5)

15 SATA3 Connector (SATA3_4)

16 Clear CMOS Jumper (CLRMOS1)

17 Chassis Intrusion and Speaker Header (SPK_CI1)

18 System Panel Header (PANEL1)

19 USB 2.0 Header (USB3_4)

20 USB 2.0 Header (USB5)

21 TPM Header (TPMS1)

22 COM Port Header (COM1)

23 Front Panel Audio Header (HD_AUDIO1)

24 Chassis/Water Pump Fan Connector (CHA_FAN1/WP)

English

8

1.4 I/O Panel

1 3

2

H370M Pro4

4

5

13 6711

12

9

10

8

No. Description No. Description

1 PS/2 Mouse Port 8 USB 3.1 Gen1 Ports (USB3_3_4)

2 D-Sub Port 9 USB 3.1 Gen2 Type-A Port (USB3_TA_1)

3 LAN RJ-45 Port* 10 USB 3.1 Gen2 Type-C Port (USB3_TC_1)

4 Line In (Light Blue)** 11 HDMI Port

5 Front Speaker (Lime)** 12 DVI-D Port

6 Microphone (Pink)** 13 PS/2 Keyboard Port

7 USB 2.0 Ports (USB12)

* ere are two LEDs on the LAN port. Please refer to the table below for the LAN port LED indications.

ACT/LINK L ED

SPEED LE D

LAN Por t

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection

English

9

** To congure 7.1 CH HD Audio, it i s required to use an HD front panel audio module and enable the multi­channel audio feature through the audio driver.

Please set Speaker Conguration to “7.1 Speaker”in the Realtek HD Audio Manager.

Function of the Audio Por ts in 7.1-channel Con guration:

English

10

Port Function

Light Blue (Rear panel) Rear Speaker Out
Lime (Rear panel) Front Speaker Out
Pink (Rear panel) Central /Subwoofer Speaker Out
Lime (Front panel) Side Speaker Out

Chapter 2 Installation

is is a Micro ATX form factor motherboard. Before you install the motherboard,

study the conguration of your chassis to ensure that the motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components

or change any motherboard settings.

Make sure to unplug the power cord before installing or removing the motherboard

•

components. Failure to do so may cause physical injuries and damages to motherboard

components.

In order to avoid damage from static electricity to the motherboard’s components,

•

NEVER place your motherboard directly on a carpet. Also remember to use a grounded

wrist strap or touch a safety grounded object before you handle the components.

Hold components by the edges and do not touch the ICs.

•

Whenever you uninstall any components, place them on a grounded anti-static pad or

•

in the bag that comes with the components.

When placing screws to secure the motherboard to the chassis, please do not over-

•

tighten the screws! Doing so may damage the motherboard.

H370M Pro4

11

English

2.1 Installing the CPU

1. Before you insert the 1151-Pin CPU into the socket , please check if the PnP c ap
is on the socket, if the CPU sur face is unclean, or if th ere are any b ent pins in the
socket. Do not force to insert the CPU into the socket if above situ ation is found.
Other wise, the CPU wil l be seriously d amaged.

2. Unplug all power cables be fore installing the CPU.

1

2

A

B

English

12

H370M Pro4

3

4

5

English

13

Please save and replace the cover if the processor i s removed. e cover must be
placed if you wish to return the motherboard for aer service.

English

14

2.2 Installing the CPU Fan and Heatsink

1 2

H370M Pro4

FAN

CPU_

English

15

2.3 Installing Memory Modules (DIMM)

is motherboard provides four 288-pin DDR4 (Double Data Rate 4) DIMM slots,

and supports Dual Channel Memory Technology.

1. For dual channel conguration, you always need to install identica l (the same

brand, speed , size and chip-type) DDR4 DIMM pairs.

2. It is unable to activate Dual Channel Memor y Technology with only one or three

memor y module installed.

3. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4

slot; otherwise, this motherboard and DIMM may be damaged.

Dual Channel Memory Conguration

Priority DDR4_ A1 DDR4_ A2 DDR4_B1 DDR4_B2

1 Populated Populated
2 Populated Populated Populated Populated

e DIMM only ts in one correct orie ntation. It will cause permanent dam age to
the mothe rboard and the DIMM if you force the DIMM into the slot at incor rect
orientation .

English

16

H370M Pro4

1

2

3

English

17

2.4 Expansion Slots (PCI Express Slots)

ere are 4 PCI Express slots on the motherboard.

Before installing an ex pansion card, please make sure that the power supply is
switched o or the power cord is unplugged. Plea se read the documentation of the
expan sion card and mak e necessary hardware settings for the card before you start
the installation.

PCIe slots:

PCIE1 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards.

PCIE2 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.

PCIE3 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.

PCIE4 (PCIe 3.0 x16 slot) is used for PCI Express x4 lane width graphics cards.

* If PCIE2 is occupied, PCIE4 will downgrade to x2 mode.

PCIe Slot Congurations

PCIE1 PCIE4

Single Graphics Card x16 N/A

English

18

Two Graphics Cards in

CrossFireXTM Mode

For a better ther mal environment, ple ase connect a ch assi s fan to the motherboard’s
chassis fan connector (CHA_ FAN1 or CHA_ FAN2) when using multiple graphics
cards.

x16 x4

2.5 Jumpers Setup

e illustration shows how jumpers are setup. When the jumper cap is placed on

the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is

“Open”.

Clear CMOS Jumper

(CLRMOS1)

(see p.7, No. 16)

CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system

parameters to default setup, please turn o the computer and unplug the power

cord from the power supply. Aer waiting for 15 seconds, use a jumper cap to

short the pins on CLR MOS1 for 5 seconds. However, please do not clear the

CMOS right aer you update the BIOS. If you need to clear the CMOS when you

just nish updating the BIOS, you must boot up the system rst, and then shut it

down before you do the clear-CMOS action. Please be noted that the password,

date, time, and user default prole will be cleared only if the CMOS battery is

removed. Please remember toremove the jumper cap aer clearing the CMOS.

2-pin Jumper

H370M Pro4

If you clear the CMOS, the case open may be detec ted. Please adjust the BIOS option
“Clear Status” to clear the record of previou s chassis intrusion status.

English

19

2.6 Onboard Headers and Connectors

SPE AKE R

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over
these header s and connectors. Placing jumper caps over the headers and connectors
will cause permanent damage to the motherboard.

System Panel Header

(9-pin PANEL1)

(see p.7, No. 18)

PWRBTN (Power Switch):

Connec t to the power switch on the chassi s front panel. You may congure the way to
turn o your system using the power switch.

RESET (Reset Switch):

Connec t to the reset switch on the chassi s front panel. P ress the reset sw itch to restart
the computer if the compute r freezes and fails to perform a normal restart.

PLED (Syste m Power LED):

Connec t to the power status indicator on the chassis front panel. e LED i s on when
the system is ope rating. e LED keeps blinking when the system i s in S1/S3 sleep
state. e LED is o when the system is in S4 sleep state or powered o (S5).

HDLED (Ha rd Drive Activity LED):

Connec t to the hard drive ac tivity LED on the chassis front panel. e LED is on
when the hard drive i s reading or writing data.

e front panel de sign may dier by chassis. A front pane l module mainly consists
of power switch , reset switch, power LED, hard dr ive activity LED, speak er and etc.
When connecting your chassis front panel module to this head er, make sure the wire
assig nments and the pin assig nments are matched correctly.

1

PLE D+

PLE D-

HDL ED-

HDL ED+

PWR BTN #

GND

RES ET#

GND

GND

Connect the power

switch, reset switch and

system status indicator on

the chassis to this header

according to the pin

assignments below. Note

the positive and negative

pins before connecting

the cables.

English

20

Chassis Intrusion and

Speaker Header

(7-pin SPK_CI1)

(see p.7, No. 17)

DUM MY
+5V

1

SIG NAL

DUM MY

GND

DUM MY

Please connect the

chassis intrusion and the

chassis speaker to this

header.

H370M Pro4

Serial ATA3 Connectors

(SATA3_0:

see p.7, No. 8)

(SATA3_1:

see p.7, No. 9)

(SATA3_2:

see p.7, No. 12)

(SATA3_3:

see p.7, No. 13)

(SATA3_4:

see p.7, No. 15)

(SATA3_5:

see p.7, No. 14)

USB 2.0 Headers

(9-pin USB3_4)

(see p.7, No. 19)

(4-pin USB5)

(see p.7, No. 20)

SATA3_2

SATA3_4

USB _PW R

1

USB _PW R

1

USB_ PWR

ese six SATA3

connectors support SATA

SATA3_0

data cables for internal

storage devices with up to

6.0 Gb/s data transfer rate.

SATA3_1

If M2_2 is occupied by a

SATA-type M.2 device,

SATA3_1 will be disabled.

SATA3_3

SATA3_5

ere are two headers on

P-

P+

GND

DUM MY

GND

P+

P-

GND

P+

P-

this motherboard.

USB 3.1 Gen1 Headers

(19-pin USB3_5_6)

(see p.7, No. 7)

(19-pin USB3_7_8)

(see p.7, No. 11)

Front Panel Audio Header

(9-pin HD_AUDIO1)

(see p.7, No. 23)

Vbus

IntA _PA_S SRX-

IntA _PA_S SRX+

GND

IntA _PA_S STX-

IntA _PA_S STX+

GND

IntA _PA_D -

IntA _PA_D +

GND

1

MIC 2_L

1

PRE SEN CE#

MIC _RE T

J_S ENS E

OUT 2_R

MIC 2_R

VbusVbus

IntA _PB_ SSRX -

IntA _PB_ SSRX +

GND

IntA _PB_ SSTX -

IntA _PB_ SSTX +

GND

IntA _PB_ D-

IntA _PB_ D+

Dumm y

OUT _RE T

OUT 2_L

ere are two headers on

this motherboard. Each

USB 3.1 Gen1 header can

support two ports.

is header is for

connecting audio devices

to the front audio panel.

English

21

1. High Denition Audio supports Jack Sensing, but the panel wire on the chassis

GND

FAN_V OLTAGE _CO NTRO L

FAN_S PEE D

FAN_S PEE D_CO NTR OL

GND

FAN_V OLTAGE _CO NTR OL

FAN_S PEE D

FAN_S PEE D_C ONTR OL

GND

FAN_V OLTAGE _CO NTRO L

FAN_S PEE D

FAN_S PEE D_CO NTR OL

must support HDA to function correctly. Please follow the instructions in our
manual and chassis manual to install your system.

2. If you use an AC’97 audio panel, please install it to the front panel audio heade r by
the steps below:
A. Connect Mic_IN (MIC) to MIC2_ L.
B. Conne ct Audio_R (RIN) to OUT2_R and Audio_ L (LIN) to OUT2_ L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_ RET and OUT_RET are for the HD audio panel only. You don’t need to
connec t them for the AC’97 audio panel.
E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel
and adju st “Recording Volume”.

English

Chassis/Water Pump Fan

Connectors

(4-pin CHA_FAN1/WP)

(see p.7, No. 24)

(4-pin CHA_FAN2/WP)

(see p.7, No. 10)

CPU Fan Connector

(4-pin CPU_FAN1)

(see p.7, No. 2)

CPU/Water Pump Fan

Connector

(4-pin CPU_FAN2/WP)

(see p.7, No. 5)

FAN _SP EED _CO NTR OL

CHA _FA N_S PEE D

FAN _VO LTA GE

4 3 2 1

is motherboard

provides two 4-Pin water

cooling

chassis

connectors. If you plan to

GND

connect a 3-Pin

water cooler fan, please

connect it to Pin 1-3.

is motherboard pro-

vides a 4-Pin CPU fan

(Quiet Fan) connector.

If you plan to connect a

3-Pin CPU fan, please

connect it to Pin 1-3.

is motherboard

provides a 4-Pin water

cooling CPU fan

connector. If you plan

to connect a 3-Pin CPU

water cooler fan, please

connect it to Pin 1-3.

fan

chassis

22