No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to
infringe.
Disclaimer:
Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.
In no event shall ASRock, its directors, ocers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of prots, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see ww w.dtsc.ca.gov/hazardouswaste/
perchlorate”
ASRock Website: http://www.asrock.com
AUSTRALIA ONLY
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage caused by our
goods. You are also entitled to have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not amount to a major failure. If
you require assistance please call ASRock Tel : +886-2-28965588 ext.123 (Standard
International call charges apply)
e terms HDMI® and HDMI High-Denition Multimedia Interface, and the
HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.
Contents
Chapter 1 Introduction 1
1.1 Package Contents 1
1.2 Specications 2
1.3 Motherboard Layout 6
1.4 I/O Panel 8
Chapter 2 Installation 10
2.1 Installing the CPU 11
2.2 Installing the CPU Fan and Heatsink 14
2.3 Installing Memory Modules (DIMM) 15
2.4 Expansion Slots (PCI and PCI Express Slots) 17
2.5 Jumpers Setup 18
2.6 Onboard Headers and Connectors 19
2.7 M.2_SSD (NGFF) Module Installation Guide 23
Chapter 3 Software and Utilities Operation 27
3.1 Installing Drivers 27
3.2 A-Tuning 28
3.3 ASRock Live Update & APP Shop 31
3.3.1 UI Overview 31
3.3.2 Apps 32
3.3.3 BIOS & Drivers 35
3.3.4 Setting 36
Chapter 4 UEFI SETUP UTILITY 37
4.1 Introduction 37
4.1.1 UEFI Menu Bar 37
4.1.2 Navigation Keys 38
4.2 Main Screen 39
4.3 Advanced Screen 40
4.3.1 CPU Conguration 41
4.3.2 DRAM Conguration 44
4.3.3 Voltage Conguration 46
4.3.4 Chipset Conguration 47
4.3.5 Storage Conguration 50
4.3.6 Serial Port Console Redirection 51
4.3.7 NVMe Conguration 52
4.3.8 Super IO Conguration 53
4.3.9 ACPI Conguration 54
4.3.10 USB Conguration 55
4.3.11 Trusted Computing 56
4.4 Tools 57
4.5 Hardware Health Event Monitoring Screen 58
4.6 Security Screen 60
4.7 Boot Screen 61
4.8 Exit Screen 64
H310CM-HDVP/DASH
Chapter 1 Introduction
ank you for purchasing ASRock H310CM-HDVP/DASH motherboard, a reliable
motherboard produced under ASRock’s consistently stringent quality control.
It delivers excellent performance with robust design conforming to ASRock’s
commitment to quality and endurance.
In this documentation, Chapter 1 and 2 contains the introduction of the
motherboard and step-by-step installation guides. Chapter 3 contains the operation
guide of the soware and utilities. Chapter 4 contains the conguration guide of
the BIOS setup.
Becau se the motherboard specications and the BIOS soware might be updated, the
content of this documentation will be subject to change without notice. In case any modications of this documentation occur, the updated version will be available on ASRock’s
website w ithout further notice. If you require technical support related to this motherboard, please visit our website for specic information about the model you are using. You
may nd the l atest VGA cards and CPU suppor t list on ASRock’s website a s well. ASRock
website http://www.asrock.com.
1.1 Package Contents
• ASRock H310CM-HDVP/DASH Motherboard (Micro ATX Form Factor)
Please realiz e that the re is a certain r isk involved with o verclocking, including adjusting
the setting in the BIOS, applying Untied Overclocking Technolog y, or using third-party
overclocking to ols. O verclocking may aect your system’s stability, or even c ause damage to
the components and devices of your system. It should be don e at your ow n risk and expense.
We are not responsibl e for possible damage caused by overclo cking.
• Microso® Windows® 10 64-bit
• FCC, CE
• ErP/EuP ready (ErP/EuP ready power supply is required)
English
5
Intel
H310
DDR 4_B1 (6 4 bit, 28 8-pin m odule )
DDR 4_A1 (6 4 bit, 28 8-pin m odule )
ATXP WR1
PCIE1
Top:
RJ-45
USB 3.1 Gen1
T: USB0
B: USB1
HDLED RESET
PLED PWRBTN
PANEL1
1
1
SPK_CI1
COM2
1
1
HD_AUDIO1
H310CM-HDVP/DASH
8
6
7
11
13
14
15
USB 2.0
T: USB0
B: USB1
USB 2.0
T: USB2
B: USB3
1
3
2
CMOS
Battery
CLRMOS1
1
4
CPU_FAN1
9
1
TPMS1
Top:
LINE I N
Cent er:
FRON T
Bott om:
MIC IN
CHA_FAN2
CHA_FAN1/WP
PCIE2
PCIE3
SATA3_1
DVI 1
VGA 1
12
USB_4_5
1
SATA3_0
SATA3_3
SATA3_2
PS2
Keyb oard
PS2
Mous e
HDM I1
PCI1
1
LPT1
BIOS
ROM
16
17
18
19
COM 1
RoHS
ATX12V1
1
USB3_2 _3
5
10
M2_ 1
CT2CT3CT4CT1
1.3 Motherboard Layout
English
6
No. Description
1ATX 12V Power Connector (ATX12V1)
2CPU Fan Connector (CPU_FAN1)
32 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)
4ATX Power Connector (ATXPWR1)
5USB 2.0 Header (USB_8_9) (shared with USB3_2 _3)
6SATA3 Connector (SATA3_3)
7SATA3 Connector (SATA3_2)
8SATA3 Connector (SATA3_1)
9SATA3 Connector (SATA3_0)
10 Clear CMOS Jumper (CLR MOS1)
11 System Panel Header (PANEL1)
12 Chassis Fan Connector (CHA_FAN2)
13 USB 2.0 Header (USB_4 _5)
14 Chassis Intrusion and Speaker Header (SPK_CI1)
15 Print Port Header (LPT1)
16 TPM Header (TPMS1)
17 COM Port Header (COM2)
18 Chassis/Water Pump Fan Connector (CHA_FAN1/WP)
19 Front Panel Audio Header (HD_AUDIO1)
H310CM-HDVP/DASH
English
7
1.4 I/O Panel
14
23
5
6
1278
11
10
9
No. DescriptionNo. Description
1PS/2 Mouse Port7Microphone (Pink)**
2COM Port 8USB 3.1 Gen1 Ports (USB01)
3D-Sub Port9USB 2.0 Ports (USB0123)
4LAN RJ-45 Port* 10HDMI Port
5Line In (Light Blue)**11DVI-D Port
6Front Speaker (Lime)**12PS/2 Keyboard Port
* ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.
** To congure 7.1 CH HD Audio, it i s required to use an HD front panel audio module and enable the multichannel audio feature through the audio driver.
Please set Speaker Conguration to “7.1 Speaker”in the Realtek HD Audio Manager.
Function of the Audio Ports in 7.1-channel Conguration:
PortFunction
Light Blue (Rear panel)Rear Speaker Out
Lime (Rear panel)Front Speaker Out
Pink (Rear panel)Central /Subwoofer Speaker Out
Lime (Front panel)Side Speaker Out
English
9
Chapter 2 Installation
is is a Micro ATX form factor motherboard. Before you install the motherboard,
study the conguration of your chassis to ensure that the motherboard ts into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
• Make sure to unplug the power cord before installing or removing the motherboard
components. Failure to do so may cause physical injuries and damages to motherboard
components.
• In order to avoid damage from static electricity to the motherboard’s components,
NEVER place your motherboard directly on a carpet. Also remember to use a grounded
wrist strap or touch a safety grounded object before you handle the components.
• Hold components by the edges and do not touch the ICs.
• Whenever you uninstall any components, place them on a grounded anti-static pad or
in the bag that comes with the components.
• When placing screws to secure the motherboard to the chassis, please do not over-
tighten the screws! Doing so may damage the motherboard.
English
10
2.1 Installing the CPU
1. Before you insert the 1151-Pin CPU into the socket, please check if the P nP cap is on the
socket, if the CPU surface is unclean, or if there are any bent pins in the sock et. Do not
force to in sert the CPU into the socket if above situation is found . Otherwise, the CPU
will be seriously damaged.
2. Unplug all power c ables before in stalling the CPU.
1
H310CM-HDVP/DASH
A
B
2
English
11
3
4
English
12
5
H310CM-HDVP/DASH
Please save and replace the cover if the processor i s removed. e cover must be placed if
you wish to return the motherboard for aer service.
13
English
2.2 Installing the CPU Fan and Heatsink
12
English
14
FAN
CPU_
H310CM-HDVP/DASH
2.3 Installing Memory Modules (DIMM)
is motherboard provides two 288-pin DDR4 (Double Data Rate 4) DIMM slots,
and supports Dual Channel Memory Technology.
1. For dual channel cong uration , you always need to in stall identical (the same
brand, speed , size and chip-type) DDR4 DIMM pairs.
2. It is unable to activate Du al Channel Memory Technology with only one memory
module installed.
3. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4
slot; otherwise, this motherboard and DIMM may be damaged.
e DIMM only ts in one correct orie ntation. It will cause permanent dam age to
the motherboard and the DIMM if you force the DIMM into the slot at incor rect
orientation.
15
English
1
2
English
16
3
H310CM-HDVP/DASH
2.4 Expansion Slots (PCI and PCI Express Slots)
ere are 1 PCI slot and 3 PCI Express slots on the motherboard.
Before installing an ex pansion card, please make sure that the power supply is
switched o or the power cord is unplugged. Plea se read the documentation of the
expan sion card and mak e necessary h ardware settings for the card before you start
the installation.
PCI slot:
e PCI1 slot is used to install expansion cards that have 32-bit PCI interface.
PCIe slots:
PCIE1 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards.
PCIE2 (PCIe 2.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIE3 (PCIe 2.0 x1 slot) is used for PCI Express x1 lane width cards.
17
English
Loading...
+ 50 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.