ASRock H170Pro4S User manual

Version 1.0
Published June 2015
Copyright©2015 ASRock INC. All rights reser ved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.
infringe.
Disclaimer:
Specications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or tness for a particular purpose.
In no event shall ASRock, its directors, ocers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of prots, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see ww w.dtsc.ca.gov/hazardouswaste/ perchlorate”
ASRock Website: http://www.asrock.com
e terms HDMI™ and HDMI High-Denition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
Contents
Chapter 1 Introduction 1
1.1 Package Contents 1
1.2 Specications 2
1.3 Motherboard Layout 6
1.4 I/O Panel 8
Chapter 2 Installation 10
2.1 Installing the CPU 11
2.2 Installing the CPU Fan and Heatsink 14
2.3 Installing Memory Modules (DIMM) 15
2.4 Expansion Slots (PCI Express Slots) 17
2.5 Jumpers Setup 18
2.6 Onboard Headers and Connectors 19
2.7 CrossFireXTM and Quad CrossFireX
TM
Operation Guide 24
2.7.1 Installing Two CrossFireXTM-Ready Graphics Cards 24
2.7.2 Driver Installation and Setup 26
2.8 M.2_SSD (NGFF) Module Installation Guide 27
Chapter 3 Software and Utilities Operation 30
3.1 Installing Drivers 30
3.2 A-Tuning 31
3.3 ASRock Live Update & APP Shop 35
3.3.1 UI Overview 35
3.3.2 Apps 36
3.3.3 BIOS & Drivers 39
3.3.4 Setting 40
3.4 Enabling USB Ports for Windows® 7 Installation 41
Chapter 4 UEFI SETUP UTILITY 44
4.1 Introduction 44
4.1.1 UEFI Menu Bar 44
4.1.2 Navigation Keys 45
4.2 Main Screen 46
4.3 OC Tweaker Screen 47
4.4 Advanced Screen 56
4.4.1 CPU Conguration 57
4.4.2 Chipset Conguration 59
4.4.3 Storage Conguration 61
4.4.4 Super IO Conguration 62
4.4.5 ACPI Conguration 63
4.4.6 USB Conguration 65
4.4.7 Trusted Computing 66
4.5 Tools 67
4.6 Hardware Health Event Monitoring Screen 71
4.7 Security Screen 73
4.8 Boot Screen 74
4.9 Exit Screen 77
Chapter 1 Introduction
ank you for purchasing ASRock H170 Pro4S motherboard, a reliable
motherboard produced under ASRock’s consistently stringent quality control.
It delivers excellent performance with robust design conforming to ASRock’s
commitment to quality and endurance.
In this documentation, Chapter 1 and 2 contains the introduction of the
motherboard and step-by-step installation guides. Chapter 3 contains the operation
guide of the soware and utilities. Chapter 4 contains the conguration guide of
the BIOS setup.
Becau se the motherboard specications and the BIOS soware might be updated, the content of this documentation will be subject to change without notice. In case any modications of this documentation occur, the updated version will be available on ASRock’s website w ithout f urther notice. If you require technical support relate d to this motherboard, please vi sit our website for s pecic information about the model you are using. You may nd the l atest VGA cards and CPU suppor t list on ASRock’s website a s well. ASRock website ht tp://www.a srock.com.
1.1 Package Contents
ASRock H170 Pro4S Motherboard (ATX Form Factor)
•
ASRock H170 Pro4S Quick Installation Guide
•
ASRock H170 Pro4S Support CD
•
2 x Serial ATA (SATA) Data Cables (Optional)
•
1 x I/O Panel Shield
•
1 x Screw for M.2 Socket
•
H170 Pro4S
English
1
1.2 Specications
Platform
CPU
Chipset
Memory
Expansion Slot
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
ATX Form Factor
Solid Capacitor design
High Density Glass Fabric PCB
Supports 6th Generation Intel® CoreTM i7/i5/i3/Pentium®/
Celeron® Processors (Socket 1151)
Digi Power design
10 Power Phase design
Supports Intel® Turbo Boost 2.0 Technology
Intel® H170
Supports Intel® Small Business Advantage 4.0
Dual Channel DDR4 Memory Technology
4 x DDR4 DIMM Slots
Supports DDR4 2133 non-ECC, un-buered memory
Max. capacity of system memory: 64GB
Supports Intel® Extreme Memory Prole (XMP) 2.0
2 x PCI Express 3.0 x16 Slots (PCIE2: x16 mode; PCIE4: x4
mode)
3 x PCI Express 3.0 x1 Slots (Flexible PCIe)
Supports AMD Quad CrossFireXTM and CrossFireXTM
English
2
Graphics
Intel® HD Graphics Built-in Visuals and the VGA outputs
•
can be supported only with processors which are GPU
integrated.
Supports Intel® HD Graphics Built-in Visuals : Intel® Quick
•
Sync Video with AVC, MVC (S3D) and MPEG-2 Full
HW Encode1, Intel® InTruTM 3D, Intel® Clear Video HD
Technology, Intel® InsiderTM, Intel® HD Graphics 510/530
Pixel Shader 5.0, DirectX 12
•
Max. shared memory 1792MB
•
Dual graphics output: Support DVI-D and HDMI ports by
•
independent display controllers
Supports HDMI with max. resolution up to 4K x 2K
•
(4096x2304) @ 24Hz
Audio
LAN
Supports DVI-D with ma x. resolution up to 1920x1200 @
•
60Hz
Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and
•
HBR (High Bit Rate Audio) with HDMI Port (Compliant
HDMI monitor is required)
Supports Accelerated Media Codecs: HEVC, VP8, VP9
•
Supports HDCP with DVI-D and HDMI Ports
•
Supports Full HD 1080p Blu-ray (BD) playback with DVI-D
•
and HDMI Ports
7.1 CH HD Audio with Content Protection (Realtek ALC892
•
Audio Codec)
* To congure 7.1 CH HD Audio, it is required to use an HD
front panel audio module and enable the multi-channel audio
feature through the audio driver.
Premium Blu-ray Audio support
•
Supports Surge Protection (ASRock Full Spike Protection)
•
ELNA Audio Caps
•
Gigabit LAN 10/100/1000 Mb/s
•
Giga PHY Intel® I219V
•
Supports Wake-On-LAN
•
Supports Lightning/ESD Protection (ASRock Full Spike
•
Protection)
Supports Energy Ecient Ethernet 802.3az
•
Supports PXE
•
H170 Pro4S
Rear Panel I/O
1 x PS/2 Mouse/Keyboard Port
•
1 x DVI-D Port
•
1 x HDMI Port
•
6 x USB 3.0 Ports (Supports ESD Protection (ASRock Full
•
Spike Protection))
1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED
•
LED)
HD Audio Jacks: Line in / Front Speaker / Microphone
•
English
3
Storage
Connector
6 x SATA3 6.0 Gb/s Connectors by Intel® H170, support
•
RAID (RAID 0, RAID 1, RAID 5, RAID 10, Intel Rapid
Storage Technology 14 and Intel Smart Response
Technology), NCQ, AHCI and Hot Plug
1 x SATA Express 10 Gb/s Connector*
•
* Support to be announced
* If M2_1 is occupied by a SATA-type M.2 device, SATA3_0 and
SATA3_1 will be disabled.
1 x Ultra M.2 Socket, supports M.2 SATA3 6.0 Gb/s module
•
and M.2 PCI Express module up to Gen3 x4 (32 Gb/s)
* Supports ASRock U.2 Kit
1 x COM Port Header
•
1 x Chassis Intrusion Header
•
1 x TPM Header
•
1 x Power LED and Speaker Header
•
1 x CPU Fan Connector (4-pin) (Smart Fan Speed Control)
•
3 x Chassis Fan Connectors (2 x 4-pin, 1 x 3-pin) (Smart Fan
•
Speed Control)
1 x 24 pin ATX Power Connector
•
1 x 8 pin 12V Power Connector
•
1 x PCIe Power Connector
•
1 x Front Panel Audio Connector
•
2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports
•
ESD Protection (ASRock Full Spike Protection))
1 x USB 3.0 Header (Supports 2 USB 3.0 ports) (Supports
•
ESD Protection (ASRock Full Spike Protection))
English
4
BIOS Feature
Hardware Monitor
128Mb AMI UEFI Legal BIOS with multilingual GUI sup-
•
port
ACPI 1.1 Compliant wake up events
•
SMBIOS 2.3.1 Support
•
CPU, GT_CPU, DRAM, VPPM, PCH 1.0V, VCCIO, VC-
•
CPLL, VCCSA Voltage Multi-adjustment
CPU/Chassis temperature sensing
•
CPU/Chassis Fan Tachometer
•
CPU/Chassis Quiet Fan (Auto adjust chassis fan speed by
•
CPU temperature)
CPU/Chassis Fan multi-speed control
•
CASE OPEN detection
•
Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, GT_CPU,
•
DRAM, VPPM, PCH 1.0V, VCCIO, VCCSA
Microso® Windows® 10 64-bit / 8.1 64-bit / 7 32-bit / 7 64-
OS
•
bit
* To install Windows® 7 OS, a modied installation disk with
xHCI drivers packed into the ISO le is required. Please refer to
page 41 for more detailed instructions.
* For the updated Windows® 10 driver, please visit ASRock ’s
website for details: http://ww w.asrock.com
FCC, CE, WHQL
Certica­tions
* For detailed product information, please visit our website: http://ww w.asrock.com
Please realize that the re is a certain r isk involved with overclo cking, including adjusting the setting in the BIOS, applying Untied Overclocking Technol ogy, or using third-party overclocking tool s. Overclocking may aect your system’s stability, or even cause dam age to the components and devices of your system. It should be done at your own risk and expense. We are not responsible for poss ible damage caused by overclocking.
•
ErP/EuP Ready (ErP/EuP ready power supply is required)
•
H170 Pro4S
English
5
1.3 Motherboard Layout
Intel
H170
DDR 4_A2 (6 4 bit, 28 8-pin m odule )
DDR 4_A1 (6 4 bit, 28 8-pin m odule )
DDR 4_B2 (6 4 bit, 28 8-pin m odule )
DDR 4_B1 (6 4 bit, 28 8-pin m odule )
ATX12V1
USB 3. 0
T: USB1
B: USB 2
ATXP WR 1
PCIE2
Top: RJ-4 5
USB 3. 0 T: USB5 B: USB 6
PCIE4
HDLED R ESET
PLED PW RBTN
PANEL1
1
USB_1_2
1
1
SPK_PLED 1
COM1
1
1
HD_AUD IO1
H170 Pro4 S
PCIE1
RoH S
8
6
7
11
12
13
14
15
16
17
18
21
HDM I1
DVI 1
USB 3. 0 T: USB3 B: USB 4
1
3
2
19
Ultr a M.2
PCIe G en3 x4
PS2
Keybo ard
/Mous e
CMO S
Bat tery
CLRMOS1
1
PCIE3
M2_ 1
CT2CT3C T4CT5
23
10
4
USB3_ 7_8
1
20
CPU_FAN1
9
USB_3_4
1
22
1
TPMS1
PCIE5
CT1
5
PCI E xpres s 3.0
Fro nt U SB 3 .0
CHA_FAN2
128M b
BIOS
Top:
LINE IN
Cent er:
FRON T
Bott om:
MIC IN
PCIE_ PWR1
CHA_FAN3
SATA3_1
SATA3_0
SATA3_5
SATA3_4
SATA3_3
SATA3_2
CHA_FAN1
CI1
1
24
26
25
SATA_EXP0
English
6
No. Description
1 ATX 12V Power Connector (ATX12V1)
2 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)
3 2 x 288-pin DDR4 DIMM Slots (DDR4_A2, DDR4_B2)
4 ATX Power Connector (ATXPWR1)
5 USB 3.0 Header (USB3_7_8)
6 SATA3 Connector (SATA3_0)
7 SATA3 Connector (SATA3_1)
8 CPU Fan Connector (CPU_FAN1)
9 SATA3 Connector (SATA3_5)
10 SATA3 Connector (SATA3_4)
11 SATA3 Connector (SATA3_2)
12 System Panel Header (PANEL1)
13 SATA3 Connector (SATA3_3)
14 Power LED and Speaker Header (SPK_PLED1)
15 SATA Express Connector (SATA_EXP0)
16 Chassis Fan Connector (CHA_FAN2)
17 Chassis Fan Connector (CHA_FAN1)
18 USB 2.0 Header (USB_3_4)
19 USB 2.0 Header (USB_1_2)
20 Chassis Intrusion Header (CI1)
21 TPM Header (TPMS1)
22 COM Port Header (COM1)
23 Front Panel Audio Header (HD_AUDIO1)
24 Clear CMOS Jumper (CLRMOS1)
25 Chassis Fan Connector (CHA_FAN3)
26 PCIe Power Connector (PCIE_PWR1)
H170 Pro4S
English
7
1.4 I/O Panel
1 2
3
4
10 569
8
7
No. Description No. Description
1 PS/2 Mouse/Keyboard Port 6 USB 3.0 Ports (USB3_5_6)
2 LAN RJ-45 Port* 7 USB 3.0 Ports (USB3_3_4)
3 Line In (Light Blue)** 8 DVI-D Port
4 Front Speaker (Lime)** 9 HDMI Port
5 Microphone (Pink)** 10 USB 3.0 Ports (USB3_1_2)
* ere are two LEDs on the LAN port. Please refer to the table below for the LAN port LED indications.
ACT/LINK L ED
SPEED LE D
LAN Por t
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 10Mbps connection Blinking Data Activity Orange 100Mbps connection On Link Green 1Gbps connection
English
8
** To congure 7.1 CH HD Audio, it i s required to use an HD front panel audio module and enable the multi­channel audio feature through the audio driver.
Please set Speaker Conguration to “7.1 Speaker”in the Realtek HD Audio Manager.
H170 Pro4S
Function of the Audio Por ts in 7.1-channel Con guration:
Port Function
Light Blue (Rear panel) Rear Speaker Out Lime (Rear panel) Front Speaker Out Pink (Rear panel) Central /Subwoofer Speaker Out Lime (Front panel) Side Speaker Out
English
9
Chapter 2 Installation
is is an ATX form factor motherboard. Before you install the motherboard, study
the conguration of your chassis to ensure that the motherboard ts into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
Make sure to unplug the power cord before installing or removing the motherboard
•
components. Failure to do so may cause physical injuries and damages to motherboard
components.
In order to avoid damage from static electricity to the motherboard’s components,
•
NEVER place your motherboard directly on a carpet. Also remember to use a grounded
wrist strap or touch a safety grounded object before you handle the components.
Hold components by the edges and do not touch the ICs.
•
Whenever you uninstall any components, place them on a grounded anti-static pad or
•
in the bag that comes with the components.
When placing screws to secure the motherboard to the chassis, please do not over-
•
tighten the screws! Doing so may damage the motherboard.
English
10
2.1 Installing the CPU
1. Before you insert the 1151-Pin CPU into the socket , please check if the PnP c ap is on the socket, if the CPU sur face is unclean, or if th ere are any b ent pins in the socket. Do not force to insert the CPU into the socket if above situ ation is found. Other wise, the CPU wil l be seriously d amaged.
2. Unplug all power ca bles before installing the CPU.
1
H170 Pro4S
A
B
2
English
11
4
5
3
12
English
Please save and replace the cover if the processor i s removed. e cover must be placed if you wish to return the motherboard for aer service.
H170 Pro4S
13
English
2.2 Installing the CPU Fan and Heatsink
1 2
English
14
FAN
CPU_
2.3 Installing Memory Modules (DIMM)
is motherboard provides four 288-pin DDR4 (Double Data Rate 4) DIMM slots,
and supports Dual Channel Memory Technology.
1. For dual channel conguration, you always need to install identical (the same
brand, speed , size and chip-type) DDR4 DIMM pairs.
2. It is unable to activate Dual Channel Memor y Technolog y with only one or thre e memor y module installed.
3. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4 slot; otherwise, this motherboard and DIMM may be damaged.
Dual Channel Memory Conguration
Priority DDR4_ A1 DDR4_ A2 DDR4_B1 DDR4_B2
1 Populated Populated 2 Populated Populated 3 Populated Populated Populated Populated
e DIMM only ts in one correct orientation. It will cause permanent dam age to the mothe rboard and the DIMM if you force the DIMM into the slot at incor rect orientation .
H170 Pro4S
15
English
1
2
3
16
English
2.4 Expansion Slots (PCI Express Slots)
ere are 5 PCI Express slots on the motherboard.
Before installing an ex pansion card, please make sure that the power supply is switched o or the power cord is unplugged. Plea se read the documentation of the expan sion card and mak e necessary hardware settings for the card before you start the installation.
PCIe slots:
PCIE1 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIE2 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards.
PCIE3 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIE4 (PCIe 3.0 x16 slot) is used for PCI Express x4 lane width graphics cards.
PCIE5 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIe Slot Congurations
PCIE2 PCIE4
Single Graphics Card x16 N/A
H170 Pro4S
Two Graphics Cards in
CrossFireXTM Mode
For a better ther mal environment, ple ase connect a ch assi s fan to the motherboard’s chassis fan connector (CHA_ FAN1, CHA_ FAN2 or CHA_ FAN3) when using mul­tiple graphics cards.
x16 x4
English
17
2.5 Jumpers Setup
e illustration shows how jumpers are setup. When the jumper cap is placed on
the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper
is “Open”. e illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”
when a jumper cap is placed on these 2 pins.
Clear CMOS Jumper
(CLRMOS1)
(see p.6, No. 24)
CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system
parameters to default setup, please turn o the computer and unplug the power
cord from the power supply. Aer waiting for 15 seconds, use a jumper cap to
short pin2 and pin3 on CLRMOS1 for 5 seconds. However, please do not clear the
CMOS right aer you update the BIOS. If you need to clear the CMOS when you
just nish updating the BIOS, you must boot up the system rst, and then shut it
down before you do the clear-CMOS action. Please be noted that the password,
date, time, and user default prole will be cleared only if the CMOS battery is
removed.
Clear CMOSDefault
English
18
If you clear the CMOS, the case open may be detec ted. Please adjust the BIOS option “Clear Status” to clear the record of previou s chassis intrusion status.
2.6 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these header s and connectors. Placing jumper caps over the headers and connectors will cause permanent damage to the motherboard.
H170 Pro4S
System Panel Header
(9-pin PANEL1)
(see p.6, No. 12)
PWRBTN (Power Switch):
Connec t to the power switch on the chassi s front panel. You may congure the way to turn o your system using the power switch.
RESET (Reset Switch):
Connec t to the reset switch on the chassi s front panel. P ress the reset sw itch to restart the computer if the compute r freezes and fails to perform a normal restart.
PLED (Syste m Power LED):
Connec t to the power status indicator on the chassis front panel. e LED i s on when the system is ope rating. e LED keeps blinking when the system i s in S1/S3 sleep state. e LED is o when the system is in S4 sleep state or powered o (S5).
HDLED (Ha rd Drive Activity LED):
Connec t to the hard drive ac tivity LED on the chassis front panel. e LED is on when the hard drive i s reading or writing data.
e front panel de sign may dier by chassis. A front pane l module mainly consists of power switch , reset switch, power LED, hard dr ive activity LED, speak er and etc. When connecting your chassis front panel module to this head er, make sure the wire assig nments and the pin assig nments are matched correctly.
1
PLE D+
PLE D-
HDL ED-
HDL ED+
PWR BTN#
GND
GND
RES ET#
GND
Connect the power
switch, reset switch and
system status indicator on
the chassis to this header
according to the pin
assignments below. Note
the positive and negative
pins before connecting
the cables.
19
English
Power LED and Speaker
PLE D-
SPE AK ER
Header
(7-pin SPK_PLED1)
(see p.6, No. 14)
DUM MY +5V
1
PLE D+
DUM MY
PLE D+
Please connect the
chassis power LED and
the chassis speaker to this
header.
Serial ATA3 Connectors
(SATA3_0:
see p.6, No. 6)
(SATA3_1:
see p.6, No. 7)
(SATA3_2:
see p.6, No. 11)
(SATA3_3:
see p.6, No. 13)
(SATA3_4:
see p.6, No. 10)
(SATA3_5:
see p.6, No. 9)
Serial ATA Express
Connectors
SATA_EXP0
(SATA_EXP0:
see p.6, No. 15)
USB 2.0 Headers
(9-pin USB_1_2)
(see p.6, No. 19)
(9-pin USB_3_4)
(see p.6, No. 18)
SATA3_1
SATA3_5
SATA3_3
1
SATA3_4
SATA3_2
SATA3_3 SATA3_2
USB _PW R
P-
P+
GND
DUM MY
GND
P+
P-
USB _PW R
ese six SATA3
connectors support SATA
data cables for internal
SATA3_0
storage devices with up to
6.0 Gb/s data transfer rate.
If the Ultra M.2 Socket
(M2_1) is occupied by a
SATA-type M.2 device,
SATA3_0 and SATA3_1
will be disabled.
Please connect either
SATA or PCIe storage
devices to these
connectors.
ere are two headers
on this motherboard.
Each USB 2.0 header can
support two ports.
English
20
Loading...
+ 58 hidden pages