Asrock H110TM-ITX R2.0 User Manual

Version 1.0

Published September 2016

Copyright©2016 ASRock INC. All rights reserved.

Copyright Notice:

No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.

Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of prots, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see ww w.dtsc.ca.gov/hazardouswaste/
perchlorate”

ASRock Website: http://www.asrock.com

AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage caused by our goods. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. If you require assistance please call ASRock Tel
: [phone] ext.123 (Standard International call charges apply)

e terms HDMI™ and HDMI High-Denition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.

Contents

Chapter 1 Introduction 1

1.1 Package Contents 1

1.2 Specications 2

1.3 Motherboard Layout 6

1.4 I/O Panel 8

Chapter 2 Installation 9

2.1 Installing the CPU 10

2.2 Installing the CPU Fan and Heatsink 13

2.3 Installing Memory Modules (SO-DIMM) 14

2.4 Jumpers Setup 15

2.5 Onboard Headers and Connectors 16

2.6 M.2 WiFi/BT Module Installation Guide 22

Chapter 3 Software and Utilities Operation 24

3.1 Installing Drivers 24

3.2 ASRock Live Update & APP Shop 25

3.2.1 UI Overview 25

3.2.2 Apps 26

3.2.3 BIOS & Drivers 29

3.2.4 Setting 30

3.3 Enabling USB Ports for Windows® 7 Installation 31

Chapter 4 UEFI SETUP UTILITY 34

4.1 Introduction 34

4.2 EZ Mode 35

4.3 Advanced Mode 36

4.3.1 UEFI Menu Bar 36

4.3.2 Navigation Keys 37

4.4 Main Screen 38

4.5 OC Tweaker Screen 39

4.6 Advanced Screen 46

4.6.1 CPU Conguration 47

4.6.2 Chipset Conguration 49

4.6.3 Storage Conguration 51

4.6.4 Super IO Conguration 52

4.6.5 ACPI Conguration 53

4.6.6 USB Conguration 54

4.7 Tools 55

4.8 Hardware Health Event Monitoring Screen 58

4.9 Security Screen 59

4.10 Boot Screen 60

4.11 Exit Screen 63

H110TM-ITX R2.0

Chapter 1 Introduction

ank you for purchasing ASRock H110TM-ITX R 2.0 motherboard, a reliable

motherboard produced under ASRock’s consistently stringent quality control.

It delivers excellent performance with robust design conforming to ASRock’s

commitment to quality and endurance.

In this documentation, Chapter 1 and 2 contains the introduction of the

motherboard and step-by-step installation guides. Chapter 3 contains the operation

guide of the soware and utilities. Chapter 4 contains the conguration guide of

the BIOS setup.

Becau se the motherboard specications and the BIOS soware might be updated, the
content of this documentation will be subject to change without notice. In case any
modications of this documentation occur, the updated version will be available on
ASRock’s website w ithout f urther notice. If you require technical support relate d to
this motherboard, please vi sit our website for s pecic information about the model
you are using. You may nd the l atest VGA cards and CPU suppor t list on ASRock’s
website a s well. ASRock website ht tp://www.a srock.com.

1.1 Package Contents

ASRock H110TM-ITX R2.0 Motherboard (in Mini-ITX Form Factor)

•

ASRock H110TM-ITX R2.0 Quick Installation Guide

•

ASRock H110TM-ITX R2.0 Support CD

•

2 x Serial ATA (SATA) Data Cables (Optional)

•

1 x SATA 1 to 2 Power Cable (Optional)

•

2 x I/O Panel Shields

•

2 x Screws for M.2 Sockets

•

English

1

1.2 Specications

Platform

CPU

Chipset

Memory

•

•

•

•

•

•

•

•

•

•

•

•

•

•

in Mini-ITX Form Factor (Compatible with Mini-ITX)

Solid Capacitor design

Supports 6th Generation Intel® CoreTM i7/i5/i3/Pentium®/

Celeron® Processors (Socket 1151)

Supports CPU up to 65W

Digi Power design

5 Power Phase design

Supports Intel® Turbo Boost 2.0 Technology

Intel® H110

Dual Channel DDR4 Memory Technology

2 x DDR4 SO-DIMM Slots

Supports DDR4 2133 non-ECC, un-buered memory

Supports ECC SO-DIMM memory modules (operate in non-

ECC mode)

Max. capacity of system memory: 32GB

Supports Intel® Extreme Memory Prole (XMP) 2.0

English

2

Expansion
Slot

Graphics

1 x M.2 Socket (Key E), supports ty pe 2230 WiFi/BT module

Intel® HD Graphics Built-in Visuals and the VGA outputs

•

can be supported only with processors which are GPU

integrated.

Supports Intel® HD Graphics Built-in Visuals : Intel® Quick

•

Sync Video with AVC, MVC (S3D) and MPEG-2 Full

HW Encode1, Intel® InTruTM 3D, Intel® Clear Video HD

Technology, Intel® InsiderTM, Intel® HD Graphics 510/530

Pixel Shader 5.0, DirectX 12

•

Max. shared memory 1024MB

•

* e size of ma ximum shared memory may vary from dierent

operating systems.

Four graphics output options: D-Sub, HDMI, DisplayPort 1.2

•

and LVDS

* Supports up to 2 displays simultaneously

Audio

H110TM-ITX R2.0

Supports HDMI with max. resolution up to 4K x 2K

•

(4096x2160) @ 24Hz / (3840x2160) @ 30Hz

Supports D-Sub with max. resolution up to 1920x1200 @

•

60Hz

Supports DisplayPort 1.2 with max. resolution up to 4K x 2K

•

(4096x2304) @ 60Hz

Supports LVDS with max. resolution up to 1920x1200 @

•

60Hz

Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and

•

HBR (High Bit Rate Audio) with HDMI Port (Compliant

HDMI monitor is required)

Supports Accelerated Media Codecs: HEVC, VP8, VP9

•

Supports HDCP with HDMI and DisplayPort 1.2 Ports

•

Supports Full HD 1080p Blu-ray (BD) playback with HDMI

•

and DisplayPort 1.2 Ports

7.1 CH HD Audio with Content Protection (Realtek ALC892

•

Audio Codec)

* To congure 7.1 CH HD Audio, it is required to use an HD

front panel audio module and enable the multi-channel audio

feature through the audio driver.

Premium Blu-ray Audio support

•

Supports Surge Protection (ASRock Full Spike Protection)

•

ELNA Audio Caps

•

LAN

Rear Panel
I/O

Gigabit LAN 10/100/1000 Mb/s

•

Giga PHY Intel® I219V

•

Supports Wake-On-LAN

•

Supports Lightning/ESD Protection (ASRock Full Spike

•

Protection)

Supports Energy Ecient Ethernet 802.3az

•

Supports PXE

•

1 x DC Jack (Compatible with the 19V power adapter)

•

1 x D-Sub Port

•

1 x HDMI Port

•

1 x DisplayPort 1.2

•

2 x USB 2.0 Ports (Supports ESD Protection (ASRock Full

•

Spike Protection))

2 x USB 3.0 Ports (Supports ESD Protection (ASRock Full

•

Spike Protection))

English

3

English

Storage

Connector

1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

•

LED)

HD Audio Jacks: Front Speaker / Microphone

•

2 x SATA3 6.0 Gb/s Connectors, support NCQ, AHCI and

•

Hot Plug

1 x M.2 Socket, supports type 2242/2260/2280 M.2 SATA3

•

6.0 Gb/s module*

* M2_ 2: RST utility port0; SATA3_0: RST utility port2;

SATA3_1: RST utility port3

1 x CIR Header

•

1 x COM Port Header

•

1 x SPDIF Out Connector

•

1 x Monitor Switch Header

•

1 x Backlight Power Jumper

•

1 x Panel Power Jumper

•

1 x Backlight Control Header

•

1 x LVDS Connector

•

1 x Home eater PC Header

•

1 x CPU Fan Connector (4-pin)

•

1 x Chassis Fan Connector (4-pin) (Smart Fan Speed Con-

•

trol)

* CHA_FAN1 can auto detect if 3-pin or 4-pin fan is in use.

* e CPU Fan Connector supports the CPU fan of ma ximum

1A (12W) fan power.

1 x Front Panel Audio Connector

•

1 x Analog Surround Audio Header

•

1 x Digital MIC Header

•

1 x 3W Audio AMP Output Wafer Header

•

1 x Internal Power Header

•

1 x SATA Power Connector

•

3 x USB 2.0 Headers (Support 5 USB 2.0 ports) (Supports

•

ESD Protection (ASRock Full Spike Protection))

1 x USB 3.0 Header (Supports 2 USB 3.0 ports) (Supports

•

ESD Protection (ASRock Full Spike Protection))

* USB3_4_5 is shared with USB4_5.

4

BIOS
Feature

Hardware
Monitor

OS

H110TM-ITX R2.0

AMI UEFI Legal BIOS with multilingual GUI support

•

ACPI 5.0 Compliant wake up events

•

SMBIOS 2.7 Support

•

DRAM Voltage Multi-adjustment

•

CPU/Chassis temperature sensing

•

CPU/Chassis Fan Tachometer

•

CPU/Chassis Quiet Fan (Auto adjust chassis fan speed by

•

CPU temperature)

CPU/Chassis Fan multi-speed control

•

Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore

•

Microso® Windows® 10 64-bit / 8.1 64-bit / 7 32-bit / 7 64-

•

bit

* To install Windows® 7 OS, a modied installation disk with

xHCI drivers packed into the ISO le is required. Please refer to

page 31 or more detailed instructions.

* For the updated Windows® 10 driver, please visit ASRock ’s

website for details: http://ww w.asrock.com

FCC, CE, WHQL

Certica­tions

* For detailed product information, please visit our website: http://ww w.asrock.com

Please realize that the re is a certain r isk involved with overclo cking, including
adjusting the setting in the BIOS, applying Untied Overclocking Technol ogy, or using
third-party overclocking tool s. Overclocking may aect your system’s stability, or
even cause dam age to the components and devices of your system. It should be done
at your own risk and expense. We are not responsible for poss ible damage caused by
overclocking.

•

ErP/EuP Ready (ErP/EuP ready power supply is required)

•

English

5

1.3 Motherboard Layout

Intel

H110

SATA_PO W1

LVDS 1

DDR4 _B 1

DDR4 _A 1

HDLED R E SET

PLED PWRBTN

PANEL1

1

BKT_ PWR1

1

PNL_ PWR1

1

USB2 _3

1

1

HDMI _SPDI F1

1

HD_A UDIO1

AUDIO
CODEC

LAN

SATA3_0

CPU_ FAN1

BIO S
ROM

DMIC 1

1

CLRM OS1

1

Fro nt

Spe ak er

Mic In

USB 2 . 0
T: U S B0
B: US B1

RJ- 45

USB 3 . 0
T: U S B0
B: US B1

DC Ja ck

VGA 1

DIS PLAY1

CHA_FAN 1

CIR1

H11 0TM-I T X

Ro HS

1

HTPC 1

BLT_VOL 1

1

1

HD_A UDIO2

SATA3_1

1

USB6

1

MONIT OR_S WITCH 1

SPEA KER1

1

ATX19 V_IN 1

USB3_ 4_5

1

COM1

HDM I1

M2 _ 1

M2 _ 2

English

6

No. Description

1 Internal Power Header (ATX19V_IN1)

2 Clear CMOS Jumper (CLRMOS1)

3 USB 2.0 Header (USB6)

4 USB 2.0 Header (USB4_5)

5 USB 3.0 Header (USB3_4_5)

6 Chassis Fan Connector (CHA_FAN1)

7 SATA3 Connector (SATA3_0)

8 SATA3 Connector (SATA3_1)

9 SATA Power Connector (SATA_POW1)

10 Monitor Switch Header (MONITOR _SWITCH1)

11 System Panel Header (PANEL1)

12 Consumer Infrared Module Header (CIR1)

13 Backlight Power Jumper (BKT_PWR1)

14 Panel Power Jumper (PNL_PWR1)

15 LVDS Connector (LVDS1)

16 Backlight Control Header (BLT_VOL1)

17 COM Port Header (COM1)

18 2 x 260-pin DDR4 SO-DIMM Slots (DDR4_A1, DDR4_B1)

19 CPU Fan Connector (CPU_FAN1)

20 USB 2.0 Header (USB2_3)

21 Home eater PC Header (HTPC1)

22 Front Panel Audio Header (HD_AUDIO1)

23 Digital MIC Header (DMIC1)

24 SPDIF Out Connector (HDMI_SPDIF1)

25 3W Audio AMP Output Wafer Header (SPEAKER1)

26 Analog Surround Audio Header (HD_AUDIO2)

H110TM-ITX R2.0

English

7

1.4 I/O Panel

No. Description No. Description

1 DC Jack** 6 LAN RJ-45 Port*

2 USB 3.0 Ports (USB3_01) 7 USB 2.0 Ports (USB01)

3 D-Sub Port (VGA1) 8 Microphone (Pink)

4 DisplayPort 1.2 (DISPLAY1) 9 Front Speaker (Lime)

5 HDMI Port (HDMI1)

* ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications .

ACT/LINK L ED

SPEED LE D

LAN Por t

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection

9872 6531 4

English

8

** Please use a 19V power adapter for the DC jack . is jack accepts dual bar rel plugs with an inner diameter of 5.1
mm and an outer diameter of 7.4 mm, where the inner contact is +19 (±10%) DC and the shell i s (centre positive).

DELTA DELTA-ADP-150TB-150W/19V

HP HP-TBC-BA52-150W/19V

FSP FSP-FSP150-A BAN1-150W/19V

DELL FA130PE1-00-130W/19.5V

DELL LA90PE0-01-90W/19.5V

is motherboard is available with support for either 2-pin ATX 19V power or DC-in power supplies. Pl ease do
not use two kinds of power supplie s at the same time! Doing so may damage the motherboard component s and
devices. When you u se the DC-in power adapter, please use the onboard SATA power connector to ge t the powe r
for HDDs.

H110TM-ITX R2.0

Chapter 2 Installation

is is a in Mini-ITX form factor motherboard. Before you install the

motherboard, study the conguration of your chassis to ensure that the

motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components

or change any motherboard settings.

Make sure to unplug the power cord before installing or removing the motherboard

•

components. Failure to do so may cause physical injuries and damages to motherboard

components.

In order to avoid damage from static electricity to the motherboard’s components,

•

NEVER place your motherboard directly on a carpet. Also remember to use a grounded

wrist strap or touch a safety grounded object before you handle the components.

Hold components by the edges and do not touch the ICs.

•

Whenever you uninstall any components, place them on a grounded anti-static pad or

•

in the bag that comes with the components.

When placing screws to secure the motherboard to the chassis, please do not over-

•

tighten the screws! Doing so may damage the motherboard.

English

9

2.1 Installing the CPU

1. Before you insert the 1151-Pin CPU into th e socket, please check if the PnP cap is on
the socket, if the CPU surfa ce is unclean, or if there are any bent pins in the socket.
Do not force to insert the CPU into the socket if above situation is found. Otherwise,
the CPU will be seriously damaged .

2. Unplug all power c ables before in stalling the CPU.

1

2

A

B

English

10

H110TM-ITX R2.0

3

4

5

English

11

Please save and replace the cover if the processor i s removed. e cover must be placed
if you wish to retur n the motherboard for aer service.

English

12

2.2 Installing the CPU Fan and Heatsink

1 2

H110TM-ITX R2.0

FAN

CPU_

English

13

2.3 Installing Memory Modules (SO-DIMM)

is motherboard provides two 260-pin DDR4 (Double Data Rate 4) SO-DIMM

slots.

It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4 slot;
otherwise , this motherboard and SO-DIMM may be damaged.

e SO-DIMM only ts in one cor rect orientation. It w ill cau se permanent damage
to the motherboard and the SO -DIMM if you force the SO-DIM M into the slot at
incorrect orientation.

1

English

14

2

2.4 Jumpers Setup

e illustration shows how jumpers are setup. When the jumper cap is placed on

the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper

is “Open”. e illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”

when a jumper cap is placed on these 2 pins.

Clear CMOS Jumper

(CLRMOS1)

(see p.6, No. 2)

CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system

parameters to default setup, please turn o the computer and unplug the power

cord from the power supply. Aer waiting for 15 seconds, use a jumper cap to

short pin2 and pin3 on CLRMOS1 for 5 seconds. However, please do not clear the

CMOS right aer you update the BIOS. If you need to clear the CMOS when you

just nish updating the BIOS, you must boot up the system rst, and then shut it

down before you do the clear-CMOS action. Please be noted that the password,

date, time, and user default prole will be cleared only if the CMOS battery is

removed.

Clear CMOSDefault

H110TM-ITX R2.0

Backlight Power Jumper

(3-pin BKT_PWR1)

(see p.6, No. 13)

Panel Power Jumper

(3-pin PNL_PWR1)

(see p.6, No. 14)

Warning:

If selected Backlight Power or Panel Power is higher than panel's spec, it may damage the

panel.

1-2 : +19V

2-3 : +12V [Default]

1-2 : +3V

2-3 : +5V [Default]

English

15

2.5 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over
these header s and connectors. Placing jumper caps over the headers and connectors
will cause permanent damage to the motherboard.

System Panel Header

(9-pin PANEL1)

(see p.6, No. 11)

PWRBTN (Power Switch):

Connec t to the power switch on the chassi s front panel. You may congure the way to
turn o your system using the power switch.

RESET (Reset Switch):

Connec t to the reset switch on the chassi s front panel. P ress the reset sw itch to restart
the computer if the compute r freezes and fails to perform a normal restart.

PLED (Syste m Power LED):

Connec t to the power status indicator on the chassis front panel. e LED i s on when
the system is ope rating. e LED keeps blinking when the system i s in S1/S3 sleep state.
e LED is o when the system i s in S4 sle ep state or powered o (S5).

HDLED (Ha rd Drive Activity LED):

Connec t to the hard drive ac tivity LED on the chassis front panel. e LED is on when
the hard dr ive is reading or w riting data.

e front panel de sign may dier by chassis. A front pane l module mainly consists
of power switch , reset switch, power LED, hard dr ive activity LED, speak er and etc.
When connecting your chassis front panel module to this head er, make sure the wire
assig nments and the pin assig nments are matched correctly.

1

PLE D+

PLE D-

HDL ED-

HDL ED+

PWR BTN #

GND

GND

RES ET#

GND

Connect the power

switch, reset switch and

system status indicator on

the chassis to this header

according to the pin

assignments below. Note

the positive and negative

pins before connecting

the cables.

English

16

Serial ATA3 Connectors

(SATA3_0:

see p.6, No. 7)

(SATA3_1:

see p.6, No. 8)

SATA3_0 SATA3_1

ese two SATA3

connectors support SATA

data cables for internal

storage devices with up to

6.0 Gb/s data transfer rate.