ASRock G Pro, GV Pro User Manual

Download

Page 1

G Pro / GV Pro

User Manual

Published October 2002

Page 2

No part of this manual may be reproduced, transcribed, transmitted, or translated in

any language, in any form or by any means, except duplication of documentation by

the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for

identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Disclaimer:Disclaimer:

Specifications and information contained in this manual are furnished for informa-

tional use only and subject to change without notice, and should not be constructed

as a commitment by ASRock. ASRock assumes no responsibility for any errors or

omissions that may appear in this manual.

With respect to the contents of this manual, ASRock does not provide warranty of

any kind, either expressed or implied, including but not limited to the implied warran-

ties or conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of profits, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from

any defect or error in the manual or product.

ASRock Website: http://www.asrock.com

Page 3

ContentsContents

Contents

ContentsContents

1 Introduction1 Introduction

1 Introduction

1 Introduction1 Introduction

1.1 Package Contents ......................................................... 4

1.2 Specifications ................................................................ 4

1.3 Motherboard Layout (G Pro) ......................................... 6

1.4 Motherboard Layout (GV Pro) ...................................... 7

1.5 ASRock I/OTM (G Pro / GV Pro) ...................................... 8

2 Installation2 Installation

2 Installation

2 Installation2 Installation

2.1 Screw Holes ................................................................. 9

2.2 Pre-installation Precautions ........................................... 9

2.3 CPU Installation .............................................................. 9

2.4 Installation of Heatsink and CPU fan ............................. 10

2.5 Installation of Memory Modules (DIMM) ......................... 10

2.6 Expansion Slots ............................................................. 11

2.7 Jumpers Setup .............................................................. 12

2.8 Connectors .................................................................... 12

3 BIOS Setup3 BIOS Setup

3 BIOS Setup

3 BIOS Setup3 BIOS Setup

3.1 BIOS Setup Program ...................................................... 15

3.1.1 BIOS Menu Bar ....................................................... 15

3.1.2 Legend Bar ............................................................. 15

3.2 Main Menu ...................................................................... 16

3.3 Advanced, Security, Power, Boot, and Exit Menus ..... 18

4 Software Support4 Software Support

4 Software Support

4 Software Support4 Software Support

4.1 Installing Operating System ........................................... 19

4.2 Support CD Information ................................................. 19

4.2.1 Running Support CD ............................................... 19

4.2.2 Drivers Menu .......................................................... 19

4.2.3 Utilities Menu ........................................................... 19

4.2.4 Contact Information ................................................ 19

Appendix: Advanced BIOS SetupAppendix: Advanced BIOS Setup

Appendix: Advanced BIOS Setup

Appendix: Advanced BIOS SetupAppendix: Advanced BIOS Setup

1. Advanced Menu .......................................................... 20

2. Security Menu ............................................................. 22

3. Power Menu ................................................................ 23

4. Boot Menu ................................................................... 24

5. Exit Menu ..................................................................... 24

......................................................................................................

...................................................

......................................................................................................

..........................................................................................................

.....................................................

..........................................................................................................

.....................................................

..........................................................................................................

......................................................................................

...........................................

......................................................................................

......................................

...................

......................................

4 4

9 9

15 15

19 19

20 20

Page 4

Chapter 1 IntroductionChapter 1 Introduction

Chapter 1 Introduction

Chapter 1 IntroductionChapter 1 Introduction

Thank you for purchasing ASRock G Pro / GV Pro motherboard, a reliable

motherboard produced under ASRock’s consistently stringent quality control. It

delivers excellent performance with robust design conforming to ASRock’s

commitment to quality and endurance.

Chapter 1 and 2 of this manual contain introduction of the motherboard and

step-by-step installation guide for new DIY system builders. Chapter 3 and 4

contain basic BIOS setup and Support CD information.

For advanced users’ reference, the Appendix offers more advanced BIOS setup

information.

1.1 Package Contents1.1 Package Contents

1.1 Package Contents

1.1 Package Contents1.1 Package Contents

ASRock G Pro or GV Pro motherboard

(Micro ATX form factor: 9.6" x 9.6", 24.4 x 24.4 cm)

ASRock G Pro / GV Pro Quick Installation Guide

ASRock Intel-SiS Support CD

1 cable for IDE devices (1 x ATA 66/100/133)

1 cable for floppy drive (1 x ribbon cable)

1 ASRock I/O shield

1 COM port bracket

1.2 Specifications1.2 Specifications

1.2 Specifications

1.2 Specifications1.2 Specifications

Platform: Micro ATX form factor (9.6" x 9.6", 24.4 x 24.4 cm)

CPU: Socket 478 for Intel® Pentium® 4

Chipsets: North Bridge: SiS 650 series chipsets; standard FSB 400

MHz, Max. 533 MHz

South Bridge: Supports USB 2.0, ATA 133

Clock Generator: 100 MHz - 200MHz

Memory: 2 slots for DDR: DIMM1 and DIMM2 (PC1600/ PC2100),

Max. 2GB

2 slots for SDR: DIMM3 and DIMM4 (PC100/ PC133),

Max. 2GB

IDE: IDE1: ATA 133 / Ultra DMA Mode 6

IDE2: ATA 133 / Ultra DMA Mode 6

Can connect up to 4 IDE devices

Floppy Port: Supports floppy disk drive

Audio: 5.1 channels AC’97 Audio

LAN: Speed: 802.3u (10/100 Ethernet), supports Wake-On-LAN

/ Celeron

processor

Page 5

Hardware Monitor: CPU temperature sensing

Chassis temperature sensing

CPU overheat shutdown to protect CPU life

Voltage monitoring: +12V, +5V, +3V, Vcore

CPU fan tachometer

Chassis fan tachometer

PCI slots: 3 slots with PCI Specification 2.2

AGP slot (for G Pro only):

1 universal AGP slot, supports 3.3v / 1.5v, 4X / 2X / 1X

AGP card

AMR slot: 1 slot, supports ASRock AMR modem card

USB 2.0: 4 default USB ports and a set of header for two additional

USB ports upgrade

ASRock I/OTM: PS/2: keyboard / mouse

RJ 45

4 rear default USB ports (USB 2.0)

1 VGA port

1 parallel port: ECP/EPP support

Audio Jack: Line Out/ Line In/ Microphone + Game port

BIOS: AMI legal BIOS

Supports “Plug and Play”

ACPI 1.1 compliance wake up events

Supports jumperfree

SMBIOS 2.3.1 support

CPU frequency stepless control

(only for advanced users’ reference)

OS: Windows 98SE / ME / 2000 / XP compliant

1. While CPU overheat is detected, the system will automatically shutdown. Please check

if the CPU fan on the motherboard functions properly before you resume the system.

2. Although G Pro/GV Pro offers stepless control, it is not recommended to perform over

clocking. Frequencies other than the recommended CPU bus frequency may cause

the instability of the system or damage the CPU.

Page 6

1.3 Motherboard Layout (G Pro1.3 Motherboard Layout (G Pro

1.3 Motherboard Layout (G Pro)

1.3 Motherboard Layout (G Pro1.3 Motherboard Layout (G Pro

45 6

24.4cm (9.6 in)

CPU_FAN1

PS/2

Mouse

PS2_USB_PWR1

PS/2

Keyboard

VGA

PARALLEL PORT

LAN

USB01

USB23

Line out

LAN PHY

Line

Line in

Mic

GAME AUDIO1

Mic in

GAME AUDIO1

CD1

AUDIO CODEC

2MB BIOS

AUX1

Super

I/O

AUDIO1

AMR1

Accelerated GraphicsPort

PCI 1

PCI 2

PCI 3

1 ATX power connector (ATXPWR1) 15 External speaker connector (SPEAKER1)

2 CPU socket 16 South Bridge controller

3 CPU fan connector (CPU_FAN1) 17 Clear CMOS (CLRCMOS1)

4 North Bridge controller 18 PCI slots

5 184-pin DDR DIMM slots (blue) 19 AUDIO CODEC

6 168-pin SDRAM DIMM slots (black) 20 Front panel audio connector (AUDIO1)

7 Primary IDE connector (IDE1, blue) 21 LAN PHY

8 Secondary IDE connector (IDE2, black) 22 PS2_USB_PWR1 jumper

9 Chassis fan connector (CHA_FAN1) 23 Internal audio connector: AUX1(white)

10 Floppy connector (FLOPPY1) 24 Internal audio connector: CD1 (black)

11 Flash Memory 25 Serial port connector (COM1)

12 System panel connector (PANEL1) 26 AMR slot

13 USB header (USB45) 27 AGP slot

14 Infrared module connector (IR1)

ATX P WR1

SiS

650 Series

Chipset

PGA478B

SiS

South Bridge

1618

DDR DIMM1(64/72 bit, 184-pinmodule)

COM1

DDR DIMM2(64/72 bit, 184-pinmodule)

CLRCMOS1

USB45

SDR DIMM1(64 bit, 168-pinmodule)

CMOS Battery

FLOPPY1

SDR DIMM2(64 bit, 168-pinmodule)

SPEAKER1

PANEL1

IDE2

CHA_FAN1

RESET HDLED

PWRBTN PLED

IDE1

IR1

24.4cm (9.6 in)

14 15

Page 7

1.4 Motherboard Layout (GV Pro1.4 Motherboard Layout (GV Pro

1.4 Motherboard Layout (GV Pro)

1.4 Motherboard Layout (GV Pro1.4 Motherboard Layout (GV Pro

45 6

24.4cm (9.6 in)

CPU_FAN1

PS/2

Mouse

PS2_USB_PWR1

PS/2

Keyboard

VGA

PARALLEL PORT

LAN

USB01

USB23

Line out

LAN PHY

Line

Line in

Mic

GAME AUDIO1

Mic in

GAME AUDIO1

CD1

AUX1

AUDIO CODEC

2MB BIOS

Super

I/O

AUDIO1

PCI 1

PCI 2

PCI 3

AMR1

1 ATX power connector (ATXPWR1) 15 External speaker connector (SPEAKER1)

2 CPU socket 16 South Bridge controller

3 CPU fan connector (CPU_FAN1) 17 Clear CMOS (CLRCMOS1)

4 North Bridge controller 18 PCI slots

5 184-pin DDR DIMM slots (blue) 19 AUDIO CODEC

6 168-pin SDRAM DIMM slots (black) 20 Front panel audio connector (AUDIO1)

7 Primary IDE connector (IDE1, blue) 21 LAN PHY

8 Secondary IDE connector (IDE2, black) 22 PS2_USB_PWR1 jumper

9 Chassis fan connector (CHA_FAN1) 23 Internal audio connector: AUX1(white)

10 Floppy connector (FLOPPY1) 24 Internal audio connector: CD1 (black)

11 Flash Memory 25 Serial port connector (COM1)

12 System panel connector (PANEL1) 26 AMR slot

13 USB header (USB45)

14 Infrared module connector (IR1)

ATX P WR1

SiS

650 Series

Chipset

GV PRO

PGA478B

SiS

South Bridge

1618

DDR DIMM1(64/72 bit, 184-pinmodule)

COM1

DDR DIMM2(64/72 bit, 184-pinmodule)

CLRCMOS1

CMOS

Battery

USB45

SDR DIMM1(64 bit, 168-pinmodule)

FLOPPY1

SDR DIMM2(64 bit, 168-pinmodule)

SPEAKER1

PANEL1

IDE2

CHA_FAN1

RESET HDLED

PWRBTN PLED

IDE1

IR1

24.4cm (9.6 in)

14 15 12

Page 8

TM TM

1.5 ASRock I/O1.5 ASRock I/O

1.5 ASRock I/O

1.5 ASRock I/O1.5 ASRock I/O

1 Parallel port 6 Line Out (Lime)

2 RJ-45 port 7 USB 2.0 ports

3 Game port 8 VGA port

4 Microphone (Pink) 9 PS/2 keyboard port (Purple)

5 Line In (Light Blue) 10 PS/2 mouse port (Green)

TM TM

(G Pro / GV Pro)(G Pro / GV Pro)

(G Pro / GV Pro)

(G Pro / GV Pro)(G Pro / GV Pro)

Page 9

Chapter 2 InstallationChapter 2 Installation

Chapter 2 Installation

Chapter 2 InstallationChapter 2 Installation

G Pro / GV Pro is a Micro ATX form factor (9.6" x 9.6", 24.4 x 24.4 cm) motherboard.

Before you install the motherboard, study the configuration of your chassis to en-

sure that the motherboard fits into it.

Make sure to unplug the power cord before installing or

removing the motherboard. Failure to do so may cause

physical injuries to you and damages to motherboard

components.

2.1 Screw Holes2.1 Screw Holes

2.1 Screw Holes

2.1 Screw Holes2.1 Screw Holes

Place screws into the holes indicated by circles to secure the motherboard

to the chassis.

Do not over-tighten the screws! Doing so may damage the

motherboard.

2.2 Pre-installation Precautions2.2 Pre-installation Precautions

2.2 Pre-installation Precautions

2.2 Pre-installation Precautions2.2 Pre-installation Precautions

Take note of the following precautions before you install motherboard components

or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any component.

2. To avoid damaging the motherboard components due to static electricity, NEVER

place your motherboard directly on the carpet or the like. Also remember to use

a grounded wrist strap or touch a safety grounded object before you handle

components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded antistatic pad or

in the bag that comes with the component.

Before you install or remove any component, ensure that the power is

switched off or the power cord is detached from the power supply.

Failure to do so may cause severe damage to the motherboard, peripherals,

and/or components.

2.3 CPU Installation2.3 CPU Installation

2.3 CPU Installation

2.3 CPU Installation2.3 CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90o to 100o angle.

Step 2. Position the CPU directly above the socket such that its marked corner

matches the base of the socket lever.

Step 3. Carefully insert the CPU into the socket until it fits in place.

Page 10

The CPU fits only in one correct orientation. DO NOT force the

CPU into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push

down the socket lever to secure the CPU. The lever clicks on the side tab

to indicate that it is locked.

Step 1 Step 2, 3 Step 4

2.4 Installation of CPU Fan and Heatsink2.4 Installation of CPU Fan and Heatsink

2.4 Installation of CPU Fan and Heatsink

2.4 Installation of CPU Fan and Heatsink2.4 Installation of CPU Fan and Heatsink

Intel® Pentium® 4 CPU requires larger heatsink and cooling fan. Thermal grease

between the CPU and the heatsink is also needed to improve heat transfer. Make

sure that the CPU and the heatsink are securely fastened and in good contact with

each other. For proper installation, please kindly refer to the instruction manuals of

vendors of CPU fan and heatsink.

2.5 Installation of Memory Modules (DIMM)2.5 Installation of Memory Modules (DIMM)

2.5 Installation of Memory Modules (DIMM)

2.5 Installation of Memory Modules (DIMM)2.5 Installation of Memory Modules (DIMM)

SDRAM (Synchronous DRAM) DIMM (Dual In-line Memory Module) has 168 pins

and DDR (Double Data Rate) SDRAM DIMM has 184 pins.

Please make sure to disconnect power supply before adding

or removing DIMMs or the system components.

168-pin RAM

The 168-pin SDRAM DIMM (black) and 184-pin DDR DIMM (blue) can be easily

distinguished by the fool-proof design.

Please do not use both 168-pin SDRAM DIMM and 184-pin

DDR DIMM at the same time. To optimize the compatibility, it

is not recommended to use two different models of the DIMMs

at the same time.

1010

184-pin RAM

Page 11

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the

break on the slot.

Step 3. Firmly insert the DIMM into the slot until the retaining clip snap back in place

and the DIMM is properly seated.

2.6 Expansion Slots (PCI, AMR, and AGP Slots)2.6 Expansion Slots (PCI, AMR, and AGP Slots)

2.6 Expansion Slots (PCI, AMR, and AGP Slots)

2.6 Expansion Slots (PCI, AMR, and AGP Slots)2.6 Expansion Slots (PCI, AMR, and AGP Slots)

There are 3 PCI slots and 1 AMR slot on both G Pro and GV Pro motherboards.

Additionally, there is one AGP slot on G Pro.

PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

AMR slot: AMR slot is used to insert AMR cards with v.92 Modem functionality.

AGP slot: The AGP slot is used to install a graphics card.

The ASRock AGP slot has a special locking mechanism which

can securely fasten the graphics card inserted.

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Installing an expansion cardInstalling an expansion card

Step 1. Before installing the expansion card, read the documentation of the

expansion card and make necessary hardware settings for the card.

Step 2. Remove the system unit cover (if your motherboard is already

installed in a chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep the

screw for later use.

Step 4. Align the card connector with the slot and press firmly until the card

is completely seated on the slot.

Step 5. Fasten the card to the chassis with screws.

Step 6. Replace the system cover.

1111

Page 12

2.7 Jumpers Setup2.7 Jumpers Setup

2.7 Jumpers Setup

2.7 Jumpers Setup2.7 Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “SHORT”. If no jumper

cap is placed on pins, the jumper is “OPEN”.

The illustration shows a 3-pin jumper whose

pin1 and pin2 are “SHORT” when jumper cap

is placed on these 2 pins.

Jumper Setting Description

PS2_USB_PWR1 Short pin2, pin3 to enable

(see p.6/p.7 item 22) +5VSB (standby) for PS/2

+5V +5VSB or USB wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current.

CLRCMOS Disconnect the power cord,

(see p.6/p.7 item 17) then short the solder points

Solder points

to clear CMOS by using

metal material, e.g., a paper

clip.

2.8 Connectors2.8 Connectors

2.8 Connectors

2.8 Connectors2.8 Connectors

Connectors are NOT jumpers. DO NOT place jumper

caps over these connectors.

Connector Figure Description

FDD connector

(33-pin FLOPPY1)

(see p.6/p.7 item 10)

Pin1

FLOPPY1

Red marking

Note: Match the red marking on the floppy ribbon cable with Pin1

Primary IDE connector (Blue)

(39-pin IDE1)

(see p.6/p.7 item 7)

Secondary IDE connector (Black)

(39-pin IDE2)

(see p.6/p.7 item 8)

1212

PIN1

Connect to the motherboard

IDE1

PIN1

BlackBlue

80-Pin ATA 100/133 cable

IDE2

Connect to the IDE devices

Page 13

Note: To optimize compatibility and performance, please connect your hard disk

drive to the primary IDE connector (IDE1, blue) and CD-ROM to the

secondary IDE connector (IDE2, black).

USB header ASRock I/OTM already

(9-pin USB45) provided 4 default USB ports.

(see p.6/p.7 item 13) If the 4-USB ports on the rear

panel are not sufficient, an

USB header is available for 2

additional USB ports.

Infrared module connector This connector supports an

(5-pin IR1) optional wireless transmitting

(see p.6/p.7 item 14) and receiving infrared module.

Internal audio connectors These connectors allow you

(4-pin CD1, 4-pin AUX1) to receive stereo audio input

(CD1: see p.6/p.7 item 24) from sound sources such as

(AUX1: see p.6/p.7 item 23) a CD-ROM, DVD/ROM, TV

tuner card, or MPEG card.

Front panel audio connector This is an interface for front

(9-pin AUDIO1) panel audio cable that allows

(see p.6/p.7 item 20) convenient connection and

control of audio devices.

System panel connector This connector accommo-

(9-pin PANEL1) dates several system front

(see p.6/p.7 item 12) panel functions.

External speaker connector This connector allows you

(4-pin SPEAKER 1) to attach to an external

(see p.6/p.7 item 15) speaker.

Chassis fan connector Connect the fan cable to the

(3-pin CHA_FAN1) connector matching the black

(see p.6/p.7 item 9) wire to the ground pin.

1313

Page 14

CPU fan connector Connect the fan cable to the

(3-pin CPU_FAN1) connector matching the black

(see p.6/p.7 item 3) wire to the ground pin.

ATX power connector Connect an ATX power

(20-pin ATXPWR1) supply to the connector.

(see p.6/p.7 item 1)

COM1 connector This connector supports a

(9-pin COM1) serial port module.

(see p.6/p.7 item 25)

ATX Power Connector

1414

Page 15

Chapter 3 BIOS SetupChapter 3 BIOS Setup

Chapter 3 BIOS Setup

Chapter 3 BIOS SetupChapter 3 BIOS Setup

3.1 BIOS Setup Utility3.1 BIOS Setup Utility

3.1 BIOS Setup Utility

3.1 BIOS Setup Utility3.1 BIOS Setup Utility

This section explains how to configure your system using the BIOS Setup Utility. The

Flash Memory on the motherboard stores the BIOS Setup Utility. When you start up

the computer, there is a chance for you to run the BIOS Setup. Press <F2> during the

Power-On-Self-Test (POST) to enter the BIOS Setup Utility, otherwise, POST

continues with its test routines.

If you wish to enter the BIOS Setup after POST, restart the system by pressing

<Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system chassis. You

can also restart by turning the system off and then back on.

The BIOS Setup Utility is designed to be user-friendly. It is a menu-driven program,

which allows you to scroll through its various sub-menus and select among the

predetermined choices.

Because the BIOS software is constantly being updated, the

following BIOS setup screens and descriptions are for reference

purpose only, and may not exactly match what you see on your

screen.

3.1.1 BIOS Menu Bar3.1.1 BIOS Menu Bar

3.1.1 BIOS Menu Bar

3.1.1 BIOS Menu Bar3.1.1 BIOS Menu Bar

The top of the screen has a menu bar with the following selections:

MAIN Sets up the basic system configuration

ADVANCED Sets up the advanced features

SECURITY Sets up the security features

POWER Configures Power Management features

BOOT Configures the default system device that is used

to locate and load the Operating System

EXIT Exits the current menu or the BIOS Setup

To access the menu bar items, press the right or left arrow key on the keyboard

until the desired item is highlighted.

3.1.2 Legend Bar3.1.2 Legend Bar

3.1.2 Legend Bar

3.1.2 Legend Bar3.1.2 Legend Bar

At the bottom of the Setup Screen is a legend bar. The following table lists the keys

in the legend bar with their corresponding functions.

1515

Page 16

Navigation Key(s) Function Description

<F1> Displays the General Help Screen

<ESC> Jumps to the Exit menu or returns to the upper menu

from the current menu

/ Moves cursor up or down between fields

/ Selects menu to the left or right

+ / - Increases or decreases values

<Enter> Brings up a selected menu for a highlighted field

<F9> Resets the current screen to its Setup Defaults

<F10> Saves changes and exits Setup

3.2 Main Menu3.2 Main Menu

3.2 Main Menu

3.2 Main Menu3.2 Main Menu

When you enter the BIOS Setup Utility, the following screen appears.

Advanced

Main

System Date System Time

Floppy Drives IDE Devices

BIOS Version Processor Type Processor Speed Cache Size Microcode Update TotalMemory

DDR1 DDR2 SDR1 SDR2

F1:Help

Esc:Exit

AMIBIOS SETUPUTILITY - VERSION3.31a

Security

Oct 142002 Mon 17:07:40

GE-PRO BIOSL0.10 Generic-X86

2000 MHz 512 KB F23/08 224 MB+ 32 MBShare Memory None None 256 MB/ 133 Mhz None

:Select Item :Select Menu

Power

+/-:Change Values

Enter:Select

Boot

Exit

Sub-Menu

[ Setup Help ]

Month: Jan - Dec

Day: 01 -31

Year:1980 - 2099

F9:Setup Defaults F10:Save &Exit

System Date [Month/Day/Year]

Set the system date that you specify. Valid values for month, day, and year are

Month: (Jan to Dec), Day: (1 to 31), Year: (up to 2099). Use keys to move

between the Month, Day and Year fields.

System Time [Hour:Minute:Second]

Set the system to the time that you specify. Use keys to move between

the Hour, Minute and Second fields.

Floppy Drives

Use this to set the type of floppy drives installed.

IDE Devices

Use this to configure IDE devices.

1616

Page 17

TYPE

It allows user to select the type of the IDE Drive. Below are the

configuration options. After making your selections on this sub-menu,

press <ESC> key to return to the upper menu, in whcih the hard

disk drive field will display the size for the hard disk drive that you

configured.

[USER]: It allows user to manually enter the number of cylinders,

heads, and sectors per track for the drive.

Before attempting to configure a hard disk drive, make sure

you have the correct configuration information supplied by

the drive manufacturer. Incorrect settings may cause the

system to fail to recognize the installed hard disk.

[Auto]:Select [Auto] to automatically detect hard disk drive. If

auto-detection is successful, the BIOS Setup automatically fills in the

correct values for the remaining fields on this sub-menu. If the auto-

detection fails, it may due to that the hard disk is too old or too new.

If the hard disk was already formatted on an older system, the BIOS

Setup may detect incorrect parameters. In these cases, select [User]

to manually enter the IDE hard disk drive parameters.

After entering the hard disk information into BIOS, use a disk

utility, such as FDISK, to partition and format new IDE hard

disk drives. This is necessary so that you can write or read

data from the hard disk. Make sure to set the partition of the

Primary IDE hard disk drives to active.

1717

Page 18

[CD/DVD]: This is used for IDE CD/DVD drives.

[ARMD]: This is used for IDE ARMD (Accelerated RemovableMedia

Device), such as MO.

Cylinders

This is used to configure the number of cylinders. Refer to the drive

documentation to determine the correct value.

Heads

This is used to configure the number of read/write heads. Refer to

the drive documentation to determine the correct values.

Write Pre-compensation

Enter Write Pre-compensation sector. Refer to the drive documentation to

determine the correct value.

Sectors

This is used to configure the number of sectors per track. Refer to the

drive documentation to determine the correct value.

Maximum Capacity

This field shows the drive’s maximum capacity as calculated by the BIOS

based on the drive information you entered.

LBA Mode

This allows user to select the LBA mode for a hard disk > 512 MB under

DOS and Windows; for Netware and UNIX user, select [Off] to disable the

LBA mode.

Block Mode

Set the block mode to [On] will enhance hard disk performance by reading

or writing more data during each transfer.

Fast Programmed I/O Modes

This allows user to set the PIO mode to enhance hard disk performance by

optimizing the hard disk timing.

32 Bit Transfer Mode

It allows user to enable 32-bit access to maximize the IDE hard disk data

transfer rate.

Ultra DMA Mode

Ultra DMA capability allows improved transfer speeds and data integrity

for compatible IDE devices. Set to [Disabled] to suppress Ultra DMA

capability.

3.3 Advanced, Security, Power, Boot, and Exit Menus3.3 Advanced, Security, Power, Boot, and Exit Menus

3.3 Advanced, Security, Power, Boot, and Exit Menus

3.3 Advanced, Security, Power, Boot, and Exit Menus3.3 Advanced, Security, Power, Boot, and Exit Menus

Detailed descriptions of these menus are listed in the Appendix, see p.20.

1818

Page 19

Chapter 4 Software SupporChapter 4 Software Suppor

Chapter 4 Software Suppor

Chapter 4 Software SupporChapter 4 Software Suppor

4.1 Install Operating System4.1 Install Operating System

4.1 Install Operating System

4.1 Install Operating System4.1 Install Operating System

This motherboard supports various Windows operating systems (98SE/ ME/ 2000/

XP). Because motherboard settings and hardware options vary, use the setup

procedures in this chapter for general reference only. Refer to your OS documen-

tation for more information.

4.2 Support CD Information4.2 Support CD Information

4.2 Support CD Information

4.2 Support CD Information4.2 Support CD Information

The Support CD that came with the motherboard contains necessary drivers and

useful utilities that enhance the motherboard features.

4.2.1 Running The Support CD4.2.1 Running The Support CD

4.2.1 Running The Support CD

4.2.1 Running The Support CD4.2.1 Running The Support CD

To begin using the support CD, insert the CD into your CD-ROM drive. The CD

automatically displays the Main Menu if “AUTORUN” is enabled in your computer.

If the Main Menu did not appear automatically, locate and double click on the file

ASSETUP.EXE from the BIN folder in the Support CD to display the menus.

4.2.2 Drivers Menu4.2.2 Drivers Menu

4.2.2 Drivers Menu

4.2.2 Drivers Menu4.2.2 Drivers Menu

The Drivers Menu shows the available devices drivers if the system detects

installed devices. Install the necessary drivers to activate the devices.

4.2.3 Utilities Menu4.2.3 Utilities Menu

4.2.3 Utilities Menu

4.2.3 Utilities Menu4.2.3 Utilities Menu

The Utilities Menu shows the applications software that the motherboard

supports. Click on a specific item then follow the installation wizard to install it.

4.2.4 ASRock PC-DIY Live Demo Program4.2.4 ASRock PC-DIY Live Demo Program

4.2.4 ASRock PC-DIY Live Demo Program

4.2.4 ASRock PC-DIY Live Demo Program4.2.4 ASRock PC-DIY Live Demo Program

ASRock presents you a multimedia PC-DIY live demo, which shows you how to

install your own PC system step by step. You can find the file through the

following path:

..\ MPEGAV \ AVSEQ01.DAT

To see this demo program, you can run Microsoft Media Player to play the file.

4.2.54.2.5

4.2.5

4.2.54.2.5

If you need to contact ASRock or want to know more about ASRock, welcome

to ASRock’s website: http://www.asrock.com; or you may contact your

dealer for further information.

Contact InformationContact Information

Contact Information

Contact InformationContact Information

1919

Page 20

Appendix: Advanced BIOS SetupAppendix: Advanced BIOS Setup

Appendix: Advanced BIOS Setup

Appendix: Advanced BIOS SetupAppendix: Advanced BIOS Setup

This section will introduce you the following BIOS Setup menus: “Advanced,”

“Security,” “Power,” “Boot,” and “Exit.”

1. Advanced BIOS Setup Menu1. Advanced BIOS Setup Menu

1. Advanced BIOS Setup Menu

1. Advanced BIOS Setup Menu1. Advanced BIOS Setup Menu

Spread Spectrum:

This field should always be “Disabled” for better system stability.

CPU Host Frequency:

[Auto]: The motherboard detects the jumper setup and sets the CPU host

frequency automatically.

[Manual]: This allows user to set CPU host frequency manually. However,

this is not recommended unless user thoroughly knows the feature.

Wrong setup may cause problems during operation.

SDRAM Frequency:

[Auto]: The motherboard detects the memory module(s) inserted and

automatically assigns appropriate frequency.

[Other values]: This allows user to select the value as operating frequency.

Chipset Configuration:

AGP Aperture Size: It refers to a section of the PCI memory address range

used for graphics memory. We recommend that you leave this field at the

default value unless your AGP card requires other sizes.

OnBoard VGA Share Memory: This allows you to select the size of share

memory for onboard VGA. Onboard VGA will get better resolution if larger

size of share memory is selected. Please do not select [None] if AGP or PCI

graphics card is not inserted.

USB Controller: Use this to enable or disable the use of USB controller.

2020

Page 21

USB Device Legacy Support: Use this to enable or disable support to emulate

legacy I/O devices such as mouse, keyboard,... etc.

Resource Configuration:

PCI Latency Timer (PCI Clocks): The default is 32. We recommend you to

keep the default value unless your PCI expansion cards’ specifications

require other settings.

Primary Graphics Adapter: Select PCI, OnBoard VGA, or Add-on AGP as the

primary graphics adapter.

Peripheral Configuration:

OnBoard FDC: Use this to enable or disable floppy drive controller.

OnBoard Serial Port: Use this to set addresses for the onboard serial ports or

disable serial ports. Configuration options: [Auto], [Disabled], [3F8 / IRQ4 /

COM1], [2F8 / IRQ3 / COM2], [3E8 / IRQ4 / COM3], [2E8 / IRQ3 / COM4].

OnBoard Infrared Port: This allows you to enable or disable the onboard

infrared port feature. Select [Auto] will enable this feature if the infrared

module is installed.

OnBoard Parallel Port: Select Parallel Port address or disable Parallel Port.

Configuration options: [Auto], [Disabled], [378], [278].

Parallel Port Mode: Set the operation mode of the parallel port.

OnBoard Midi Port: Select address for Midi Port or disable Midi Port. Configu

ration options: [Disabled], [330], [300], [290], [292].

Midi IRQ Select: Use this to select Midi IRQ. Configuration options: [5],

[10], [11]. The default is 5.

2121

Page 22

OnBoard Game Port: Select address for Game Port or disable Game Port.

Configuration options: [200h], [208h], [Disabled].

OnBoard IDE: To enable either the primary IDE channel or the secondary IDE

channel, set to [Disabled] will disable the both.

Configuration options: [both], [Disabled], [Primary], [Secondary].

OnBoard AC’97 Audio: Enable or disable onboard AC’97 audio feature.

OnBoard MC’97 Modem: Enable or disable onboard MC’97 modem feature.

System Hardware Monitor: You can check the status of the hardware on

your system. It allows you to monitor the parameters for CPU temperature,

Motherboard temperature, CPU fan speed, and critical voltage.

2. Security Setup Menu2. Security Setup Menu

2. Security Setup Menu

2. Security Setup Menu2. Security Setup Menu

Supervisor Password: This field shows the status of the Supervisor Password.

[Clear]: No password has been set.

[Set]: Supervisor password has been set.

User Password: This field shows the status of the User Password.

[Clear]: No password has been set.

[Set]: User password has been set.

Set Supervisor Password: Press <Enter> to set Supervisor Password. Valid

password can be a 1 to 6 alphanumeric characters combination. If you already

have a password, you must enter your current password first in order to

create a new password.

Set User Password: Press <Enter> to set User Password. Valid password can

be a 1 to 6 alphanumeric characters combination. If you already have a

password, you must enter your current password first in order to create a new

password.

Password Check: Select the check point for “Password Check”. Configuration

options: [Setup], [Always]. If [Setup] option is selected, the “Password Check”

2222

Page 23

is performed before BIOS setup. If [Always] option is selected, the “Password

Check” is performed before both boot-up and BIOS setup.

3. Power Setup Menu3. Power Setup Menu

3. Power Setup Menu

3. Power Setup Menu3. Power Setup Menu

Suspend to RAM (S3): This field allows you to select whether to auto-detect or

disable the ACPI Suspend-to-RAM feature. Select [Auto] will enable this feature

if the system supports it.

Repost Video on S3 Resume: This feature allows you to repost video on S3

resume.

Restore on AC/Power Loss: This allows you to set the power state after an

unexpected AC power loss. If [Power Off] is selected, the AC power remains

off when the power recovers. If [Power On] is selected, the AC power

resumes and the system starts to boot up when the power recovers.

Ring-In Power On: Use this to enable or disable Ring-in signals to turn on the

system from the power-soft-off mode.

PME# Power On: Use this to enable or disable PCI PME# to turn on the system from

the power-soft-off mode.

Keyboard Power On: Use this to enable or disable keyboard to turn on the system

from the power-soft-off mode.

RTC Alarm Power On: Use this to enable or disable RTC(Real Time Clock) to power

on the system. If [Enable] is selected, you must fill the RTC Alarm Date / Hour /

Minute / Second sub-fields with the actual wake up time you desire.

2323

Page 24

4. Boot Setup Menu4. Boot Setup Menu

4. Boot Setup Menu

4. Boot Setup Menu4. Boot Setup Menu

Quick Boot Mode: This mode speeds up the boot-up routine by skipping memory

retestings.

Boot-time Diagnostic Screen: This screen shows CPU and hardware

information during Power-On-Self-Test (POST) routine. If this screen is disabled,

only ASRock logo is shown during the boot up process.

Boot Up Num-Lock: This automatically activates the Numeric Lock function after

boot up.

Boot to OS/2: This enables boot up to OS/2 operating system.

Boot Device Priority: This allows you to set the boot device priority.

5. Exit Menu5. Exit Menu

5. Exit Menu

5. Exit Menu5. Exit Menu

2424

Page 25

Exit Saving Changes: After you enter the sub-menu, the message “Save current

settings and exit” will appear. If you press <ENTER>, it will save the current

settings and exit the BIOS SETUP Utility.

Exit Discarding Changes: After you enter the submenu, the message “Quit

without saving changes” will appear. If you press <ENTER>, you will exit the

BIOS Setup Utility without making any changes to the settings.

Load Default Settings: This loads the default values for all the setup configuration.

Discard Changes: After you enter the sub-menu, the message “Load setup

original values” will appear. If you press <ENTER>, original values will be restored.

All changes are discarded.

2525