ASROCK EP2C602-2T2OS6/D16, EP2C602-2L+OS6/D16, EP2C602-2OS6/D16, EP2C602-2T/D16, EP2C602-2O/D16 User Manual

1

EP2C602-2T2OS6/D16

EP2C602-2TS6/D16

EP2C602-2L+2OS6/D16

EP2C602-2L+OS6/D16

EP2C602-2OS6/D16

EP2C602-2T/D16

EP2C602-2O/D16

EP2C602-O/D16

EP2C602-2L+O/D16

EP2C602-2L+/D16

EP2C602-S6/D16

User Manual

Version 1.3

Published October 2013

Copyright©2013 ASRock INC. All rights reserved.

2

Copyright Notice:

No part of this manual may be reproduced, transcribed, transmitted, or translated in

any language, in any form or by any means, except duplication of documentation by

the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this manual may or may not be regis-

tered trademarks or copyrights of their respective companies, and are used only for

identication or explanation and to the owners’ benet, without intent to infringe.

Disclaimer:

Specications and information contained in this manual are furnished for informa-

tional use only and subject to change without notice, and should not be constructed

as a commitment by ASRock. ASRock assumes no responsibility for any errors or

omissions that may appear in this manual.

With respect to the contents of this manual, ASRock does not provide warranty of

any kind, either expressed or implied, including but not limited to the implied warran-

ties or conditions of merchantability or tness for a particular purpose.

In no event shall ASRock, its directors, ofcers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of prots, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from

any defect or error in the manual or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-

lowing two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic

substance controlled in Perchlorate Best Management Practices (BMP) regulations

passed by the California Legislature. When you discard the Lithium battery in Cali-

fornia, USA, please follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see

www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

3

Contents

1 Introduction ....................................................... 5

1.1 Package Contents ............................................... 5

1.2 Specications ...................................................... 6

1.3 Motherboard Layout ............................................ 9

1.4 I/O Panel ............................................................. 42

1.5 Block Diagram ..................................................... 53

2 Installation ......................................................... 54

2.1 Pre-installation Precautions ................................ 54

2.2 Screw Holes ........................................................ 54

2.3 CPU Installation .................................................. 55

2.4 Installation of Heatsink and CPU fan .................. 57

2.5 Installation of Memory Modules (DIMM) ............. 58

2.6 Expansion Slots (PCI Express Slots) .................. 60

2.7 Jumpers Setup .................................................... 61

2.8 Onboard Headers and Connectors ..................... 62

2.9 Driver Installation Guide ...................................... 69

3 UEFI SETUP UTILITY ......................................... 70

3.1 Introduction ......................................................... 70

3.1.1 UEFI Menu Bar ........................................... 70

3.1.2 Navigation Keys ......................................... 71

3.2 Main Screen ........................................................ 72

3.3 Advanced Screen ................................................ 73

3.3.1 ACPI Conguration ..................................... 74

3.3.2 Intel(LT-SX) TXT Conguration .................. 75

3.3.3 WHEA Conguration .................................. 76

3.3.4 CPU Conguration ..................................... 77

3.3.5 North Bridge Conguration ......................... 79

3.3.6 South Bridge Conguration ........................ 82

3.3.7 USB Conguration ...................................... 83

3.3.8 Intel ME Subsystem ................................... 84

3.3.9 Clock Generator Conguration ................... 85

3.3.10 Storage Conguration .............................. 86

3.3.11 Super IO Conguration ............................. 88

3.3.12 Serial Port Console Redirection ............... 89

3.3.13 Voltage Control ......................................... 90

4

3.4 Hardware Health Event Monitoring Screen ......... 91

3.5 Server Management ............................................ 93

3.6 Boot Screen ........................................................ 94

3.7 Security Screen ................................................... 96

3.8 Exit Screen .......................................................... 97

3.9 Event Logs .......................................................... 98

4 Software Support .............................................. 99

4.1 Install Operating System ..................................... 99

4.2 Support CD Information ...................................... 99

4.2.1 Running Support CD .................................. 99

4.2.2 Drivers Menu .............................................. 99

4.2.3 Utilities Menu .............................................. 99

4.2.4 Contact Information .................................... 99

5 Troubleshooting ................................................ 100

5.1 Troubleshooting Procedures ............................... 100

5.2 Technical Support Procedures ............................ 102

5.3 Returning Merchandise for Service ..................... 102

5

Chapter 1: Introduction

Thank you for purchasing ASRock EP2C602 Series motherboard, a reli-

able motherboard produced under ASRock’s consistently stringent quality

control. It delivers excellent performance with robust design conforming to

ASRock’s commitment to quality and endurance.

In this manual, chapter 1 and 2 contains the introduction of the mother-

board and step-by-step hardware installation guide. Chapter 3 and 4 con-

tains the conguration guide of BIOS setup and information of the Support

CD.

Because the motherboard specications and the BIOS software

might be updated, the content of this manual will be subject to

change without notice. In case any modications of this manual

occur, the updated version will be available on ASRock’s web-

site without further notice. You may nd the latest VGA cards

and CPU support list on ASRock’s website as well. ASRock

website http://www.asrock.com

If you require technical support related to this motherboard,

please visit our website for specic information about the model

you are using.

www.asrock.com/support/index.asp

1.1 Package Contents

ASRock EP2C602 Series Motherboard

(SSI EEB Form Factor: 12.0-in x 13-in, 30.5 cm x 33.0 cm)

User Manual

Support CD

2 x Serial ATA (SATA) Data Cables (Optional)

1 x I/O Panel Shield

6

1.2 Specications

Physical
Status

Form Factor SSI EEB

Dimension 12'' x 13'' (30.5 cm x 33.0 cm)

Processor
System

CPU

Supports Intel® Xeon processor E5­1600*/2600/4600 & v2 series
* E5-1600 support single socket.

Socket Dual Socket R (LGA2011)

Power Phase 5 +1 Power Phase Design

Chipset Intel® C602

BIOS BIOS type 64Mb AMI UEFI Legal BIOS

System
Memory

Max.
Capacity

512GB DDR3 RDIMM

Socket 16 x 240-pin DDR3 DIMM slots

Type

Quad Channel DDR3 1600/1333/1066 LR /
Registered /ECC/ UDIMM

Voltage 1.5V, 1.35V

Expansion
Slot

PCIe 3.0 x 16

2 slots (2 x16)

PCIe 3.0 x 4

NA

PCIe 2.0 x 1

NA

PCI

NA

Storage

SATA/SAS
controller

Intel® C602: 2 x SATA3 6.0 Gb/s, 8 x
SATA2 3.0 Gb/s (from 2 x mini SAS 8087

connector)

Additional
SATA
controller

NA

Additional
SAS2
controller

EP2C602-2T2OS6/D16 / EP2C602-2TS6/
D16 / EP2C602-2L+2OS6/D16 / EP2C602­2L+OS6/D16 / EP2C602-2OS6/D16 /
EP2C602-S6/D16

LSI 2308: 8 x SAS2 6Gbps (from 2 x mini

SAS 8087 connector)

EP2C602-2T/D16 / EP2C602-2O/D16 /
EP2C602-O/D16 / EP2C602-2L+O/D16 /
EP2C602-2L+/D16

NA

7

Graphics

Controller ASPEED AST2300

VRAM DDR3 16MB

Output

Supports D-Sub with max. resolution up to
1920x1200 @ 60Hz

Ethernet

Interface

Intel® 82599ES/82599EN: 10G
Intel® X540-AT2: 10G/1G/100M
Intel® i350: 1G/100M/10M

LAN
Controller

EP2C602-2T2OS6/D16

1 x Intel® 82599ES (10G ber, SFP+), 1 x
Intel® X540-AT2 (10GBase-T)

EP2C602-2L+2OS6/D16

1 x Intel® 82599ES (10G ber, SFP+), 1 x
Intel® i350 (GLAN)

EP2C602-2OS6/D16 / EP2C602-2O/D16

1 x Intel® 82599ES (10G ber, SFP+)

EP2C602-2TS6/D16 / EP2C602-2T/D16

1 x Intel® X540-AT2 (10GBase-T)

EP2C602-O/D16

1 x Intel® 82599EN (10G ber, SFP+)

EP2C602-2L+OS6/D16 / EP2C602-2L+O/

D16

1 x Intel® 82599EN (10G ber, SFP+), 1 x
Intel® i350 (GLAN)

EP2C602-2L+/D16 / EP2C602-S6/D16

1 x Intel® i350 (GLAN)

Manage­ment

Controller

ASPEED AST2300

IPMI
dedicated
GLAN

Realtek RTL8211E

Audio Audio Codec

NA

Rear Panel
I/O

Lan port

(SFP+)

EP2C602-2T2OS6/D16 / EP2C602-

2L+2OS6/D16 / EP2C602-2OS6/D16 /

EP2C602-2O/D16

2

EP2C602-2L+OS6/D16 / EP2C602-2L+O/

D16 / EP2C602-O/D16

1

8

EP2C602-2TS6/D16 / EP2C602-2T/D16 /

EP2C602-2L+/D16 / EP2C602-S6/D16

0

Lan port

(RJ45)

EP2C602-2T2OS6/D16 / EP2C602-

2L+2OS6/D16 / EP2C602-2L+OS6/D16
/ EP2C602-2TS6/D16 / EP2C602-2T/D16 /
EP2C602-2L+O/D16 / EP2C602-2L+/D16 /

EP2C602-O/D16 / EP2C602-S6/D16

2 + 1 (for IPMI)

PS/2 KB/
mouse

NA

VGA port D-sub x 1

USB port 4 x USB 2.0

Serial port 1 (COM1)

Audio jack NA

Internal
connector

COM port
header

1 (COM2)

Auxiliary
panel header

1 (include chassis intrusion, location button

& LED, front LAN LED)

TPM header 1

IPMB header 1

Buzzer 1

Fan header 8 x 4-pin

ATX power 1 (24-pin) + 2 (8-pin)

USB header 2 (each support 2 USB 2.0)

Type A USB

2.0 port

1

Internal
connector

80 debug
port LED

1

Front panel 1

Speaker

(4pin)

1

1394 header NA

Support OS OS

Microsoft® Windows® Server 2008 / 2008
R2 / Linux compliant

* For detailed product information, please visit our website: http://www.asrock.com

9

1.3 Motherboard Layout

EP2C602-2T2OS6/D16

30.5cm (12 in)

33.0cm (13 i n)

Intel

C602

ATXP WR1

DDR3 _F2 (6 4 bit, 24 0-pi n modul e)

DDR3 _F1 (6 4 bit, 24 0-pi n modul e)

DDR3 _E2 (6 4 bit, 24 0-pi n modul e)

DDR3 _E1 (6 4 bit, 24 0-pi n modul e)

EP 2C 602-2 T2 OS 6/ D16

ATX12V_ 1

Top:
MNG_ LAN

USB 2.0
T: USB 3
B: U SB4

LAN1

VGA 1

COM 1

CMO S

Bat tery

Ro H S

Dr.

Deb ug

PCIE7

USB _8

1

TR1

FRONT_LED_ LAN34

HDLED RESET

PLED PWRBT N

PANEL1

USB_5 _6

1

COM2

1

TPM1

1

NMI_BTN1

1

AUX_PANE L1

1

ME_RECOV ERY1

1

IPMB_1

1

SATA_SGPIO1

1

BMC
ROM

BUZZER 1

64Mb
BIOS

SATAIII_0

SATAIII_1

SATAII_

PORT_ 0

FRNT_FA N4

PCIE6

4

5

1

2

3 6

7

9

8

12

1

PSU_S MB1

14

10

11

13

15

32

35

34 33

36

39

40

41

42

43

44

37

38

45

1

SPEAKER1

DDR3 _C1 (6 4 bit, 24 0-pi n modul e)

DDR3 _C2 (6 4 bit, 24 0-pi n modul e)

DDR3 _D1 (6 4 bit, 24 0-pi n modul e)

DDR3 _D2 (6 4 bit, 24 0-pi n modul e)

DDR3 _G1 (6 4 bit, 24 0-pi n modul e)

DDR3 _G2 (6 4 bit, 24 0-pi n modul e)

DDR3 _H1 (6 4 bit, 24 0-pi n modul e)

DDR3 _H2 (6 4 bit, 24 0-pi n modul e)

DDR3 _B2 (6 4 bit, 24 0-pi n modul e)

DDR3 _B1 (6 4 bit, 24 0-pi n modul e)

DDR3 _A2 (6 4 bit, 24 0-pi n modul e)

DDR3 _A1 (6 4 bit, 24 0-pi n modul e)

ATX12V1

FRNT_FA N3

CPU2_FA N

FRNT_FA N1

CPU1_FA N

FRNT_FA N2

REAR_FA N1

REAR_FA N2

USB 2.0
T: USB 1
B: U SB2

LAN2

LAN3

LAN4

UID_LE D1

UID_SW

LSI_SA S_0

SCU_

PORT_ 0LSI_SA S_1

10G B ase -T
10G S FP+
SAS 2 .0

1

12V_SW1

1

1

BMC_SMB _1

1

BMC_SMB _3

1

3031

29

26

25

24

23

22

21

18

17

16

20

28

27

19

10

1 Dr. Debug

2 ME Recovery Jumper (ME_RECOVERY1)

3 Non Maskable Interrupt Button (NMI_BTN1)

4

Auxiliary panel header (AUX_PANEL1)

5 System Panel Header (PANEL1)

6 -12V Switch Header (12V_SW1)

7 COM Port Header (COM2)

8 ATX Power Connector (ATXPWR1)

9 Intelligent Platform Management Bus header (IPMB_1)

10 PSU SMBus (PSU_SMB1)

11 TPM Header (TPM1)

12

Thermal Sensor header (TR1)

13 Front Lan LED Connector (FRONT_LED_LAN34)

14 2 x 240-pin DDR3 DIMM Slots

(DDR3_F2, DDR3_E2, White)

15 2 x 240-pin DDR3 DIMM Slots

(DDR3_F1, DDR3_E1, Blue)

16 ATX 12V Power Connector (ATX12V_1)

17 CPU Fan Connector (CPU2_FAN)

18 Front Fan Connector (FRNT_FAN4)

19 Front Fan Connector (FRNT_FAN3)

20 2011-Pin CPU Socket (CPU_AP1)

21 2 x 240-pin DDR3 DIMM Slots

(DDR3_H2, DDR3_G2, White)

22 2 x 240-pin DDR3 DIMM Slots

(DDR3_A1, DDR3_B1, Blue)

23 2011-Pin CPU Socket (CPU_BSP1)

24 Front Fan Connector (FRNT_FAN2)

25 Front Fan Connector (FRNT_FAN1)

26 CPU Fan Connector (CPU1_FAN)

27 ATX 12V Power Connector (ATX12V1)

28 2 x 240-pin DDR3 DIMM Slots

(DDR3_D2, DDR3_C2, White)

29 2 x 240-pin DDR3 DIMM Slots

(DDR3_C1, DDR3_D1, Blue)

11

30 USB 2.0 Header (USB_5_6)

31 USB 2.0 Port (USB_8)

32 Speaker Header (SPEAKER1)

33 SATA SGPIO Connector (SATA_SGPIO1)

34

SATA2 Connector (SATAII_PORT_0)

35 SCU Connector (SCU_PORT_0)

36 LSI SAS Connector (LSI_SAS_0

)

37 LSI SAS Connector (LSI_SAS_1

)

38 SATA3 Connector (SATA

III_1)

39 SATA3 Connector (SATA

III_0)

40 BMC SMB Header (BMC_SMB1)

41 BMC SMB Header (BMC_SMB3)

42

2 x 240-pin DDR3 DIMM Slots

(DDR3_A2, DDR3_B2, White)

43 2 x 240-pin DDR3 DIMM Slots

(DDR3_H1, DDR3_G1, Blue)

44 Rear Fan Connector (REAR_FAN2)

45 Rear Fan Connector (REAR_FAN1)

12

EP2C602-2TS6/D16

30.5cm (12 in)

Intel

C602

ATXP WR1

DDR3 _F2 (6 4 bit, 24 0-pi n modul e)

DDR3 _F1 (6 4 bit, 24 0-pi n modul e)

DDR3 _E2 (6 4 bit, 24 0-pi n modul e)

DDR3 _E1 (6 4 bit, 24 0-pi n modul e)

EP 2C 602-2 TS 6/ D1 6

ATX12V_ 1

Top:
MNG_ LAN

USB 2.0
T: USB 3
B: U SB4

LAN1

VGA 1

COM 1

CMO S

Bat tery

Ro H S

Dr.

Deb ug

PCIE7

USB _8

1

TR1

FRONT_LED_ LAN34

HDLED RESET

PLED PWRBT N

PANEL1

USB_5 _6

1

COM2

1

TPM1

1

NMI_BTN1

1

AUX_PANE L1

1

ME_RECOV ERY1

1

IPMB_1

1

SATA_SGPIO1

1

BMC
ROM

BUZZER 1

64Mb
BIOS

SATAIII_0

SATAIII_1

SATAII_

PORT_ 0

FRNT_FA N4

PCIE6

4

5

1

2

3 6

7

9

8

12

1

PSU_S MB1

14

10

11

13

15

32

35

34 33

36

394037

38

1

SPEAKER1

DDR3 _C1 (6 4 bit, 24 0-pi n modul e)

DDR3 _C2 (6 4 bit, 24 0-pi n modul e)

DDR3 _D1 (6 4 bit, 24 0-pi n modul e)

DDR3 _D2 (6 4 bit, 24 0-pi n modul e)

DDR3 _G1 (6 4 bit, 24 0-pi n modul e)

DDR3 _G2 (6 4 bit, 24 0-pi n modul e)

DDR3 _H1 (6 4 bit, 24 0-pi n modul e)

DDR3 _H2 (6 4 bit, 24 0-pi n modul e)

DDR3 _B2 (6 4 bit, 24 0-pi n modul e)

DDR3 _B1 (6 4 bit, 24 0-pi n modul e)

DDR3 _A2 (6 4 bit, 24 0-pi n modul e)

DDR3 _A1 (6 4 bit, 24 0-pi n modul e)

ATX12V1

FRNT_FA N3

CPU2_FA N

FRNT_FA N1

CPU1_FA N

FRNT_FA N2

REAR_FA N1

REAR_FA N2

USB 2.0
T: USB 1
B: U SB2

LAN2

UID_LE D1

UID_SW

LSI_SA S_0

SCU_

PORT_ 0

LSI_SA S_1

10G B ase -T

SAS 2 .0

1

12V_SW1

1

1

BMC_SMB _1

1

BMC_SMB _3

1

3031

29

26

25

24

23

22

21

18

17

16

20

28

27

19

41

42

43

44

45

33.0cm (13 i n)

13

1 Dr. Debug

2 ME Recovery Jumper (ME_RECOVERY1)

3 Non Maskable Interrupt Button (NMI_BTN1)

4

Auxiliary panel header (AUX_PANEL1)

5 System Panel Header (PANEL1)

6 -12V Switch Header (12V_SW1)

7 COM Port Header (COM2)

8 ATX Power Connector (ATXPWR1)

9 Intelligent Platform Management Bus header (IPMB_1)

10 PSU SMBus (PSU_SMB1)

11 TPM Header (TPM1)

12

Thermal Sensor header (TR1)

13 Front Lan LED Connector (FRONT_LED_LAN34)

14 2 x 240-pin DDR3 DIMM Slots

(DDR3_F2, DDR3_E2, White)

15 2 x 240-pin DDR3 DIMM Slots

(DDR3_F1, DDR3_E1, Blue)

16 ATX 12V Power Connector (ATX12V_1)

17 CPU Fan Connector (CPU2_FAN)

18 Front Fan Connector (FRNT_FAN4)

19 Front Fan Connector (FRNT_FAN3)

20 2011-Pin CPU Socket (CPU_AP1)

21 2 x 240-pin DDR3 DIMM Slots

(DDR3_H2, DDR3_G2, White)

22 2 x 240-pin DDR3 DIMM Slots

(DDR3_A1, DDR3_B1, Blue)

23 2011-Pin CPU Socket (CPU_BSP1)

24 Front Fan Connector (FRNT_FAN2)

25 Front Fan Connector (FRNT_FAN1)

26 CPU Fan Connector (CPU1_FAN)

27 ATX 12V Power Connector (ATX12V1)

28 2 x 240-pin DDR3 DIMM Slots

(DDR3_D2, DDR3_C2, White)

29 2 x 240-pin DDR3 DIMM Slots

(DDR3_C1, DDR3_D1, Blue)

14

30 USB 2.0 Header (USB_5_6)

31 USB 2.0 Port (USB_8)

32 Speaker Header (SPEAKER1)

33

SATA SGPIO Connector (SATA_SGPIO1)

34 SATA2 Connector (SATAII_PORT_0)

35 SCU Connector (SCU_PORT_0)

36 LSI SAS Connector (LSI_SAS_0

)

37 LSI SAS Connector (LSI_SAS_1

)

38 SATA3 Connector (SATA

III_1)

39 SATA3 Connector (SATA

III_0)

40 BMC SMB Header (BMC_SMB1)

41

BMC SMB Header (BMC_SMB3)

42 2 x 240-pin DDR3 DIMM Slots

(DDR3_A2, DDR3_B2, White)

43 2 x 240-pin DDR3 DIMM Slots

(DDR3_H1, DDR3_G1, Blue)

44 Rear Fan Connector (REAR_FAN2)

45 Rear Fan Connector (REAR_FAN1)

15

EP2C602-2L+2OS6/D16

30.5cm (12 in)

Intel

C602

ATXP WR1

DDR3 _F2 (6 4 bit, 24 0-pi n modul e)

DDR3 _F1 (6 4 bit, 24 0-pi n modul e)

DDR3 _E2 (6 4 bit, 24 0-pi n modul e)

DDR3 _E1 (6 4 bit, 24 0-pi n modul e)

EP 2C 602-2 L+ 2O S6 /D16

ATX12V_ 1

Top:
MNG_ LAN

USB 2.0
T: USB 3
B: U SB4

LAN1

VGA 1

COM 1

CMO S

Bat tery

Ro H S

Dr.

Deb ug

PCIE7

USB _8

1

TR1

FRONT_LED_ LAN34

HDLED RESET

PLED PWRBT N

PANEL1

USB_5 _6

1

COM2

1

TPM1

1

NMI_BTN1

1

AUX_PANE L1

1

ME_RECOV ERY1

1

IPMB_1

1

SATA_SGPIO1

1

BMC
ROM

BUZZER 1

64Mb
BIOS

SATAIII_0

SATAIII_1

SATAII_

PORT_ 0

FRNT_FA N4

PCIE6

4

5

1

2

3 6

7

9

8

12

1

PSU_S MB1

14

10

11

13

15

32

35

34 33

36

39

40

41

42

43

44

37

38

45

1

SPEAKER1

DDR3 _C1 (6 4 bit, 24 0-pi n modul e)

DDR3 _C2 (6 4 bit, 24 0-pi n modul e)

DDR3 _D1 (6 4 bit, 24 0-pi n modul e)

DDR3 _D2 (6 4 bit, 24 0-pi n modul e)

DDR3 _G1 (6 4 bit, 24 0-pi n modul e)

DDR3 _G2 (6 4 bit, 24 0-pi n modul e)

DDR3 _H1 (6 4 bit, 24 0-pi n modul e)

DDR3 _H2 (6 4 bit, 24 0-pi n modul e)

DDR3 _B2 (6 4 bit, 24 0-pi n modul e)

DDR3 _B1 (6 4 bit, 24 0-pi n modul e)

DDR3 _A2 (6 4 bit, 24 0-pi n modul e)

DDR3 _A1 (6 4 bit, 24 0-pi n modul e)

ATX12V1

FRNT_FA N3

CPU2_FA N

FRNT_FA N1

CPU1_FA N

FRNT_FA N2

REAR_FA N1

REAR_FA N2

USB 2.0
T: USB 1
B: U SB2

LAN2

LAN3

LAN4

UID_LE D1

UID_SW

LSI_SA S_0

SCU_

PORT_ 0

LSI_SA S_1

10G S FP+
SAS 2 .0

1

12V_SW1

1

1

BMC_SMB _1

1

BMC_SMB _3

1

3031

29

26

25

24

23

22

21

18

17

16

20

28

27

19

33.0cm (13 i n)

16

1 Dr. Debug

2 ME Recovery Jumper (ME_RECOVERY1)

3 Non Maskable Interrupt Button (NMI_BTN1)

4

Auxiliary panel header (AUX_PANEL1)

5 System Panel Header (PANEL1)

6 -12V Switch Header (12V_SW1)

7 COM Port Header (COM2)

8 ATX Power Connector (ATXPWR1)

9 Intelligent Platform Management Bus header (IPMB_1)

10 PSU SMBus (PSU_SMB1)

11 TPM Header (TPM1)

12

Thermal Sensor header (TR1)

13 Front Lan LED Connector (FRONT_LED_LAN34)

14 2 x 240-pin DDR3 DIMM Slots

(DDR3_F2, DDR3_E2, White)

15 2 x 240-pin DDR3 DIMM Slots

(DDR3_F1, DDR3_E1, Blue)

16 ATX 12V Power Connector (ATX12V_1)

17 CPU Fan Connector (CPU2_FAN)

18 Front Fan Connector (FRNT_FAN4)

19 Front Fan Connector (FRNT_FAN3)

20 2011-Pin CPU Socket (CPU_AP1)

21 2 x 240-pin DDR3 DIMM Slots

(DDR3_H2, DDR3_G2, White)

22 2 x 240-pin DDR3 DIMM Slots

(DDR3_A1, DDR3_B1, Blue)

23 2011-Pin CPU Socket (CPU_BSP1)

24 Front Fan Connector (FRNT_FAN2)

25 Front Fan Connector (FRNT_FAN1)

26 CPU Fan Connector (CPU1_FAN)

27 ATX 12V Power Connector (ATX12V1)

28 2 x 240-pin DDR3 DIMM Slots

(DDR3_D2, DDR3_C2, White)

29 2 x 240-pin DDR3 DIMM Slots

(DDR3_C1, DDR3_D1, Blue)

17

30 USB 2.0 Header (USB_5_6)

31 USB 2.0 Port (USB_8)

32 Speaker Header (SPEAKER1)

33 SATA SGPIO Connector (SATA_SGPIO1)

34

SATA2 Connector (SATAII_PORT_0)

35 SCU Connector (SCU_PORT_0)

36 LSI SAS Connector (LSI_SAS_0

)

37 LSI SAS Connector (LSI_SAS_1

)

38 SATA3 Connector (SATA

III_1)

39 SATA3 Connector (SATA

III_0)

40 BMC SMB Header (BMC_SMB1)

41 BMC SMB Header (BMC_SMB3)

42 2 x 240-pin DDR3 DIMM Slots

(DDR3_A2, DDR3_B2, White)

43 2 x 240-pin DDR3 DIMM Slots

(DDR3_H1, DDR3_G1, Blue)

44 Rear Fan Connector (REAR_FAN2)

45 Rear Fan Connector (REAR_FAN1)

18

EP2C602-2L+OS6/D16

30.5cm (12 in)

Intel

C602

ATXP WR1

DDR3 _F2 (6 4 bit, 24 0-pi n modul e)

DDR3 _F1 (6 4 bit, 24 0-pi n modul e)

DDR3 _E2 (6 4 bit, 24 0-pi n modul e)

DDR3 _E1 (6 4 bit, 24 0-pi n modul e)

EP 2C 602-2 L+ OS 6/ D16

ATX12V_ 1

Top:
MNG_ LAN

USB 2.0
T: USB 3
B: U SB4

LAN1

VGA 1

COM 1

CMO S

Bat tery

Ro H S

Dr.

Deb ug

PCIE7

USB _8

1

TR1

FRONT_LED_ LAN34

HDLED RESET

PLED PWRBT N

PANEL1

USB_5 _6

1

COM2

1

TPM1

1

NMI_BTN1

1

AUX_PANE L1

1

ME_RECOV ERY1

1

IPMB_1

1

SATA_SGPIO1

1

BMC
ROM

BUZZER 1

64Mb
BIOS

SATAIII_0

SATAIII_1

SATAII_

PORT_ 0

FRNT_FA N4

PCIE6

4

5

1

2

3 6

7

9

8

12

1

PSU_S MB1

14

10

11

13

15

32

35

34 33

36

39

40

41

42

43

44

37

38

45

1

SPEAKER1

DDR3 _C1 (6 4 bit, 24 0-pi n modul e)

DDR3 _C2 (6 4 bit, 24 0-pi n modul e)

DDR3 _D1 (6 4 bit, 24 0-pi n modul e)

DDR3 _D2 (6 4 bit, 24 0-pi n modul e)

DDR3 _G1 (6 4 bit, 24 0-pi n modul e)

DDR3 _G2 (6 4 bit, 24 0-pi n modul e)

DDR3 _H1 (6 4 bit, 24 0-pi n modul e)

DDR3 _H2 (6 4 bit, 24 0-pi n modul e)

DDR3 _B2 (6 4 bit, 24 0-pi n modul e)

DDR3 _B1 (6 4 bit, 24 0-pi n modul e)

DDR3 _A2 (6 4 bit, 24 0-pi n modul e)

DDR3 _A1 (6 4 bit, 24 0-pi n modul e)

ATX12V1

FRNT_FA N3

CPU2_FA N

FRNT_FA N1

CPU1_FA N

FRNT_FA N2

REAR_FA N1

REAR_FA N2

USB 2.0
T: USB 1
B: U SB2

LAN2

LAN3

UID_LE D1

UID_SW

LSI_SA S_0

SCU_

PORT_ 0LSI_SA S_1

10G S FP+
SAS 2 .0

1

12V_SW1

1

1

BMC_SMB _1

1

BMC_SMB _3

1

3031

29

26

25

24

23

22

21

18

17

16

20

28

27

19

33.0cm (13 i n)

19

1 Dr. Debug

2 ME Recovery Jumper (ME_RECOVERY1)

3 Non Maskable Interrupt Button (NMI_BTN1)

4 Auxiliary panel header (AUX_PANEL1)

5 System Panel Header (PANEL1)

6 -12V Switch Header (12V_SW1)

7 COM Port Header (COM2)

8 ATX Power Connector (ATXPWR1)

9 Intelligent Platform Management Bus header (IPMB_1)

10 PSU SMBus (PSU_SMB1)

11 TPM Header (TPM1)

12 Thermal Sensor header (TR1)

13 Front Lan LED Connector (FRONT_LED_LAN34)

14 2 x 240-pin DDR3 DIMM Slots

(DDR3_F2, DDR3_E2, White)

15 2 x 240-pin DDR3 DIMM Slots

(DDR3_F1, DDR3_E1, Blue)

16 ATX 12V Power Connector (ATX12V_1)

17 CPU Fan Connector (CPU2_FAN)

18 Front Fan Connector (FRNT_FAN4)

19 Front Fan Connector (FRNT_FAN3)

20 2011-Pin CPU Socket (CPU_AP1)

21 2 x 240-pin DDR3 DIMM Slots

(DDR3_H2, DDR3_G2, White)

22 2 x 240-pin DDR3 DIMM Slots

(DDR3_A1, DDR3_B1, Blue)

23 2011-Pin CPU Socket (CPU_BSP1)

24 Front Fan Connector (FRNT_FAN2)

25 Front Fan Connector (FRNT_FAN1)

26 CPU Fan Connector (CPU1_FAN)

27 ATX 12V Power Connector (ATX12V1)

28 2 x 240-pin DDR3 DIMM Slots

(DDR3_D2, DDR3_C2, White)

29 2 x 240-pin DDR3 DIMM Slots

(DDR3_C1, DDR3_D1, Blue)

20

30 USB 2.0 Header (USB_5_6)

31 USB 2.0 Port (USB_8)

32 Speaker Header (SPEAKER1)

33

SATA SGPIO Connector (SATA_SGPIO1)

34 SATA2 Connector (SATAII_PORT_0)

35 SCU Connector (SCU_PORT_0)

36 LSI SAS Connector (LSI_SAS_0

)

37 LSI SAS Connector (LSI_SAS_1

)

38 SATA3 Connector (SATA

III_1)

39 SATA3 Connector (SATA

III_0)

40 BMC SMB Header (BMC_SMB1)

41

BMC SMB Header (BMC_SMB3)

42 2 x 240-pin DDR3 DIMM Slots

(DDR3_A2, DDR3_B2, White)

43 2 x 240-pin DDR3 DIMM Slots

(DDR3_H1, DDR3_G1, Blue)

44 Rear Fan Connector (REAR_FAN2)

45 Rear Fan Connector (REAR_FAN1)

21

EP2C602-2OS6/D16

30.5cm (12 in)

Intel

C602

ATXP WR1

DDR3 _F2 (6 4 bit, 24 0-pi n modul e)

DDR3 _F1 (6 4 bit, 24 0-pi n modul e)

DDR3 _E2 (6 4 bit, 24 0-pi n modul e)

DDR3 _E1 (6 4 bit, 24 0-pi n modul e)

EP 2C 602-2 OS 6/ D1 6

ATX12V_ 1

Top:
MNG_ LAN

USB 2.0
T: USB 3
B: U SB4

VGA 1

COM 1

CMO S

Bat tery

Ro H S

Dr.

Deb ug

PCIE7

USB _8

1

TR1

FRONT_LED_ LAN34

HDLED RESET

PLED PWRBT N

PANEL1

USB_5 _6

1

COM2

1

TPM1

1

NMI_BTN1

1

AUX_PANE L1

1

ME_RECOV ERY1

1

IPMB_1

1

SATA_SGPIO1

1

BMC
ROM

BUZZER 1

64Mb
BIOS

SATAIII_0

SATAIII_1

SATAII_

PORT_ 0

FRNT_FA N4

PCIE6

4

5

1

2

3 6

7

9

8

12

1

PSU_S MB1

14

10

11

13

15

32

35

34 33

36

394037

38

1

SPEAKER1

DDR3 _C1 (6 4 bit, 24 0-pi n modul e)

DDR3 _C2 (6 4 bit, 24 0-pi n modul e)

DDR3 _D1 (6 4 bit, 24 0-pi n modul e)

DDR3 _D2 (6 4 bit, 24 0-pi n modul e)

DDR3 _G1 (6 4 bit, 24 0-pi n modul e)

DDR3 _G2 (6 4 bit, 24 0-pi n modul e)

DDR3 _H1 (6 4 bit, 24 0-pi n modul e)

DDR3 _H2 (6 4 bit, 24 0-pi n modul e)

DDR3 _B2 (6 4 bit, 24 0-pi n modul e)

DDR3 _B1 (6 4 bit, 24 0-pi n modul e)

DDR3 _A2 (6 4 bit, 24 0-pi n modul e)

DDR3 _A1 (6 4 bit, 24 0-pi n modul e)

ATX12V1

FRNT_FA N3

CPU2_FA N

FRNT_FA N1

CPU1_FA N

FRNT_FA N2

REAR_FA N1

REAR_FA N2

USB 2.0
T: USB 1
B: U SB2

LAN3

LAN4

UID_LE D1

UID_SW

LSI_SA S_0

SCU_

PORT_ 0

LSI_SA S_1

10G S FP+
SAS 2 .0

1

12V_SW1

1

1

BMC_SMB _1

1

BMC_SMB _3

1

3031

29

26

25

24

23

22

21

18

17

16

20

28

27

19

41

42

43

44

45

33.0cm (13 i n)

22

1 Dr. Debug

2 ME Recovery Jumper (ME_RECOVERY1)

3 Non Maskable Interrupt Button (NMI_BTN1)

4

Auxiliary panel header (AUX_PANEL1)

5 System Panel Header (PANEL1)

6 -12V Switch Header (12V_SW1)

7 COM Port Header (COM2)

8 ATX Power Connector (ATXPWR1)

9 Intelligent Platform Management Bus header (IPMB_1)

10 PSU SMBus (PSU_SMB1)

11 TPM Header (TPM1)

12 Thermal Sensor header (TR1)

13 Front Lan LED Connector (FRONT_LED_LAN34)

14 2 x 240-pin DDR3 DIMM Slots

(DDR3_F2, DDR3_E2, White)

15 2 x 240-pin DDR3 DIMM Slots

(DDR3_F1, DDR3_E1, Blue)

16 ATX 12V Power Connector (ATX12V_1)

17 CPU Fan Connector (CPU2_FAN)

18 Front Fan Connector (FRNT_FAN4)

19 Front Fan Connector (FRNT_FAN3)

20 2011-Pin CPU Socket (CPU_AP1)

21 2 x 240-pin DDR3 DIMM Slots

(DDR3_H2, DDR3_G2, White)

22 2 x 240-pin DDR3 DIMM Slots

(DDR3_A1, DDR3_B1, Blue)

23 2011-Pin CPU Socket (CPU_BSP1)

24 Front Fan Connector (FRNT_FAN2)

25 Front Fan Connector (FRNT_FAN1)

26 CPU Fan Connector (CPU1_FAN)

27 ATX 12V Power Connector (ATX12V1)

28 2 x 240-pin DDR3 DIMM Slots

(DDR3_D2, DDR3_C2, White)

29 2 x 240-pin DDR3 DIMM Slots

(DDR3_C1, DDR3_D1, Blue)

23

30 USB 2.0 Header (USB_5_6)

31 USB 2.0 Port (USB_8)

32 Speaker Header (SPEAKER1)

33 SATA SGPIO Connector (SATA_SGPIO1)

34 SATA2 Connector (SATAII_PORT_0)

35 SCU Connector (SCU_PORT_0)

36 LSI SAS Connector (LSI_SAS_0

)

37 LSI SAS Connector (LSI_SAS_1

)

38 SATA3 Connector (SATA

III_1)

39 SATA3 Connector (SATA

III_0)

40 BMC SMB Header (BMC_SMB1)

41 BMC SMB Header (BMC_SMB3)

42 2 x 240-pin DDR3 DIMM Slots

(DDR3_A2, DDR3_B2, White)

43 2 x 240-pin DDR3 DIMM Slots

(DDR3_H1, DDR3_G1, Blue)

44 Rear Fan Connector (REAR_FAN2)

45 Rear Fan Connector (REAR_FAN1)

24

EP2C602-2T/D16

30.5cm (12 in)

Intel

C602

ATXP WR1

DDR3 _F2 (6 4 bit, 24 0-pi n modul e)

DDR3 _F1 (6 4 bit, 24 0-pi n modul e)

DDR3 _E2 (6 4 bit, 24 0-pi n modul e)

DDR3 _E1 (6 4 bit, 24 0-pi n modul e)

EP 2C 602-2 T/ D1 6

ATX12V_ 1

Top:
MNG_ LAN

USB 2.0
T: USB 3
B: U SB4

LAN1

VGA 1

COM 1

CMO S

Bat tery

Ro H S

Dr.

Deb ug

PCIE7

USB _8

1

TR1

FRONT_LED_ LAN34

HDLED RESET

PLED PWRBT N

PANEL1

USB_5 _6

1

COM2

1

TPM1

1

NMI_BTN1

1

AUX_PANE L1

1

ME_RECOV ERY1

1

IPMB_1

1

SATA_SGPIO1

1

BMC
ROM

BUZZER 1

64Mb
BIOS

SATAIII_0

SATAIII_1

SATAII_

PORT_ 0

FRNT_FA N4

PCIE6

4

5

1

2

3 6

7

9

8

12

1

PSU_S MB1

14

10

11

13

15

32

35

34 33

37

36

1

SPEAKER1

DDR3 _C1 (6 4 bit, 24 0-pi n modul e)

DDR3 _C2 (6 4 bit, 24 0-pi n modul e)

DDR3 _D1 (6 4 bit, 24 0-pi n modul e)

DDR3 _D2 (6 4 bit, 24 0-pi n modul e)

DDR3 _G1 (6 4 bit, 24 0-pi n modul e)

DDR3 _G2 (6 4 bit, 24 0-pi n modul e)

DDR3 _H1 (6 4 bit, 24 0-pi n modul e)

DDR3 _H2 (6 4 bit, 24 0-pi n modul e)

DDR3 _B2 (6 4 bit, 24 0-pi n modul e)

DDR3 _B1 (6 4 bit, 24 0-pi n modul e)

DDR3 _A2 (6 4 bit, 24 0-pi n modul e)

DDR3 _A1 (6 4 bit, 24 0-pi n modul e)

ATX12V1

FRNT_FA N3

CPU2_FA N

FRNT_FA N1

CPU1_FA N

FRNT_FA N2

REAR_FA N1

REAR_FA N2

USB 2.0
T: USB 1
B: U SB2

LAN2

UID_LE D1

UID_SW

SCU_PO RT_0

10G B ase -T

1

12V_SW1

1

1

BMC_SMB _1

1

BMC_SMB _3

1

3031

29

26

25

24

23

22

21

18

17

16

20

28

27

19

38

39

40

41

42

43

33.0cm (13 i n)

25

1 Dr. Debug

2 ME Recovery Jumper (ME_RECOVERY1)

3 Non Maskable Interrupt Button (NMI_BTN1)

4

Auxiliary panel header (AUX_PANEL1)

5 System Panel Header (PANEL1)

6 -12V Switch Header (12V_SW1)

7 COM Port Header (COM2)

8 ATX Power Connector (ATXPWR1)

9 Intelligent Platform Management Bus header (IPMB_1)

10 PSU SMBus (PSU_SMB1)

11 TPM Header (TPM1)

12 Thermal Sensor header (TR1)

13 Front Lan LED Connector (FRONT_LED_LAN34)

14 2 x 240-pin DDR3 DIMM Slots

(DDR3_F2, DDR3_E2, White)

15 2 x 240-pin DDR3 DIMM Slots

(DDR3_F1, DDR3_E1, Blue)

16 ATX 12V Power Connector (ATX12V_1)

17 CPU Fan Connector (CPU2_FAN)

18 Front Fan Connector (FRNT_FAN4)

19 Front Fan Connector (FRNT_FAN3)

20 2011-Pin CPU Socket (CPU_AP1)

21 2 x 240-pin DDR3 DIMM Slots

(DDR3_H2, DDR3_G2, White)

22 2 x 240-pin DDR3 DIMM Slots

(DDR3_A1, DDR3_B1, Blue)

23 2011-Pin CPU Socket (CPU_BSP1)

24 Front Fan Connector (FRNT_FAN2)

25 Front Fan Connector (FRNT_FAN1)

26 CPU Fan Connector (CPU1_FAN)

27 ATX 12V Power Connector (ATX12V1)

28 2 x 240-pin DDR3 DIMM Slots

(DDR3_D2, DDR3_C2, White)

29 2 x 240-pin DDR3 DIMM Slots

(DDR3_C1, DDR3_D1, Blue)

26

30 USB 2.0 Header (USB_5_6)

31 USB 2.0 Port (USB_8)

32 Speaker Header (SPEAKER1)

33

SATA SGPIO Connector (SATA_SGPIO1)

34 SATA2 Connector (SATAII_PORT_0)

35 SCU Connector (SCU_PORT_0)

36 SATA3 Connector (SATA

III_1)

37 SATA3 Connector (SATA

III_0)

38 BMC SMB Header (BMC_SMB1)

39 BMC SMB Header (BMC_SMB3)

40 2 x 240-pin DDR3 DIMM Slots

(DDR3_A2, DDR3_B2, White)

41 2 x 240-pin DDR3 DIMM Slots

(DDR3_H1, DDR3_G1, Blue)

42 Rear Fan Connector (REAR_FAN2)

43 Rear Fan Connector (REAR_FAN1)

27

EP2C602-2O/D16

30.5cm (12 in)

Intel

C602

ATXP WR1

DDR3 _F2 (6 4 bit, 24 0-pi n modul e)

DDR3 _F1 (6 4 bit, 24 0-pi n modul e)

DDR3 _E2 (6 4 bit, 24 0-pi n modul e)

DDR3 _E1 (6 4 bit, 24 0-pi n modul e)

EP 2C 602-2 O/ D1 6

ATX12V_ 1

Top:
MNG_ LAN

USB 2.0
T: USB 3
B: U SB4

VGA 1

COM 1

CMO S

Bat tery

Ro H S

Dr.

Deb ug

PCIE7

USB _8

1

TR1

FRONT_LED_ LAN34

HDLED RESET

PLED PWRBT N

PANEL1

USB_5 _6

1

COM2

1

TPM1

1

NMI_BTN1

1

AUX_PANE L1

1

ME_RECOV ERY1

1

IPMB_1

1

SATA_SGPIO1

1

BMC
ROM

BUZZER 1

64Mb
BIOS

SATAIII_0

SATAIII_1

SATAII_

PORT_ 0

FRNT_FA N4

PCIE6

4

5

1

2

3 6

7

9

8

12

1

PSU_S MB1

14

10

11

13

15

32

35

34 33

37

38

36

1

SPEAKER1

DDR3 _C1 (6 4 bit, 24 0-pi n modul e)

DDR3 _C2 (6 4 bit, 24 0-pi n modul e)

DDR3 _D1 (6 4 bit, 24 0-pi n modul e)

DDR3 _D2 (6 4 bit, 24 0-pi n modul e)

DDR3 _G1 (6 4 bit, 24 0-pi n modul e)

DDR3 _G2 (6 4 bit, 24 0-pi n modul e)

DDR3 _H1 (6 4 bit, 24 0-pi n modul e)

DDR3 _H2 (6 4 bit, 24 0-pi n modul e)

DDR3 _B2 (6 4 bit, 24 0-pi n modul e)

DDR3 _B1 (6 4 bit, 24 0-pi n modul e)

DDR3 _A2 (6 4 bit, 24 0-pi n modul e)

DDR3 _A1 (6 4 bit, 24 0-pi n modul e)

ATX12V1

FRNT_FA N3

CPU2_FA N

FRNT_FA N1

CPU1_FA N

FRNT_FA N2

REAR_FA N1

REAR_FA N2

USB 2.0
T: USB 1
B: U SB2

LAN3

LAN4

UID_LE D1

UID_SW

SCU_PO RT_0

10G S FP+

1

12V_SW1

1

1

BMC_SMB _1

1

BMC_SMB _3

1

3031

29

26

25

24

23

22

21

18

17

16

20

28

27

19

39

40

41

42

43

33.0cm (13 i n)

28

1 Dr. Debug

2 ME Recovery Jumper (ME_RECOVERY1)

3 Non Maskable Interrupt Button (NMI_BTN1)

4

Auxiliary panel header (AUX_PANEL1)

5 System Panel Header (PANEL1)

6 -12V Switch Header (12V_SW1)

7 COM Port Header (COM2)

8 ATX Power Connector (ATXPWR1)

9 Intelligent Platform Management Bus header (IPMB_1)

10 PSU SMBus (PSU_SMB1)

11 TPM Header (TPM1)

12 Thermal Sensor header (TR1)

13 Front Lan LED Connector (FRONT_LED_LAN34)

14 2 x 240-pin DDR3 DIMM Slots

(DDR3_F2, DDR3_E2, White)

15 2 x 240-pin DDR3 DIMM Slots

(DDR3_F1, DDR3_E1, Blue)

16 ATX 12V Power Connector (ATX12V_1)

17 CPU Fan Connector (CPU2_FAN)

18 Front Fan Connector (FRNT_FAN4)

19 Front Fan Connector (FRNT_FAN3)

20 2011-Pin CPU Socket (CPU_AP1)

21 2 x 240-pin DDR3 DIMM Slots

(DDR3_H2, DDR3_G2, White)

22 2 x 240-pin DDR3 DIMM Slots

(DDR3_A1, DDR3_B1, Blue)

23 2011-Pin CPU Socket (CPU_BSP1)

24 Front Fan Connector (FRNT_FAN2)

25 Front Fan Connector (FRNT_FAN1)

26 CPU Fan Connector (CPU1_FAN)

27 ATX 12V Power Connector (ATX12V1)

28 2 x 240-pin DDR3 DIMM Slots

(DDR3_D2, DDR3_C2, White)

29 2 x 240-pin DDR3 DIMM Slots

(DDR3_C1, DDR3_D1, Blue)

29

30 USB 2.0 Header (USB_5_6)

31 USB 2.0 Port (USB_8)

32 Speaker Header (SPEAKER1)

33

SATA SGPIO Connector (SATA_SGPIO1)

34 SATA2 Connector (SATAII_PORT_0)

35 SCU Connector (SCU_PORT_0)

36 SATA3 Connector (SATA

III_1)

37 SATA3 Connector (SATA

III_0)

38 BMC SMB Header (BMC_SMB1)

39 BMC SMB Header (BMC_SMB3)

40 2 x 240-pin DDR3 DIMM Slots

(DDR3_A2, DDR3_B2, White)

41 2 x 240-pin DDR3 DIMM Slots

(DDR3_H1, DDR3_G1, Blue)

42 Rear Fan Connector (REAR_FAN2)

43 Rear Fan Connector (REAR_FAN1)

30

EP2C602-O/D16

30.5cm (12 in)

Intel

C602

ATXP WR1

DDR3 _F2 (6 4 bit, 24 0-pi n modul e)

DDR3 _F1 (6 4 bit, 24 0-pi n modul e)

DDR3 _E2 (6 4 bit, 24 0-pi n modul e)

DDR3 _E1 (6 4 bit, 24 0-pi n modul e)

EP 2C 602-O /D 16

ATX12V_ 1

Top:
MNG_ LAN

USB 2.0
T: USB 3
B: U SB4

VGA 1

COM 1

CMO S

Bat tery

Ro H S

Dr.

Deb ug

PCIE7

USB _8

1

TR1

FRONT_LED_ LAN34

HDLED RESET

PLED PWRBT N

PANEL1

USB_5 _6

1

COM2

1

TPM1

1

NMI_BTN1

1

AUX_PANE L1

1

ME_RECOV ERY1

1

IPMB_1

1

SATA_SGPIO1

1

BMC
ROM

BUZZER 1

64Mb
BIOS

SATAIII_0

SATAIII_1

SATAII_

PORT_ 0

FRNT_FA N4

PCIE6

4

5

1

2

3 6

7

9

8

12

1

PSU_S MB1

14

10

11

13

15

32

35

34 33

37

38

36

1

SPEAKER1

DDR3 _C1 (6 4 bit, 24 0-pi n modul e)

DDR3 _C2 (6 4 bit, 24 0-pi n modul e)

DDR3 _D1 (6 4 bit, 24 0-pi n modul e)

DDR3 _D2 (6 4 bit, 24 0-pi n modul e)

DDR3 _G1 (6 4 bit, 24 0-pi n modul e)

DDR3 _G2 (6 4 bit, 24 0-pi n modul e)

DDR3 _H1 (6 4 bit, 24 0-pi n modul e)

DDR3 _H2 (6 4 bit, 24 0-pi n modul e)

DDR3 _B2 (6 4 bit, 24 0-pi n modul e)

DDR3 _B1 (6 4 bit, 24 0-pi n modul e)

DDR3 _A2 (6 4 bit, 24 0-pi n modul e)

DDR3 _A1 (6 4 bit, 24 0-pi n modul e)

ATX12V1

FRNT_FA N3

CPU2_FA N

FRNT_FA N1

CPU1_FA N

FRNT_FA N2

REAR_FA N1

REAR_FA N2

USB 2.0
T: USB 1
B: U SB2

LAN3

UID_LE D1

UID_SW

SCU_

PORT_ 0

10G S FP+

1

12V_SW1

1

1

BMC_SMB _1

1

BMC_SMB _3

1

3031

29

26

25

24

23

22

21

18

17

16

20

28

27

19

39

40

41

42

43

33.0cm (13 i n)

31

1 Dr. Debug

2 ME Recovery Jumper (ME_RECOVERY1)

3 Non Maskable Interrupt Button (NMI_BTN1)

4

Auxiliary panel header (AUX_PANEL1)

5 System Panel Header (PANEL1)

6 -12V Switch Header (12V_SW1)

7 COM Port Header (COM2)

8 ATX Power Connector (ATXPWR1)

9 Intelligent Platform Management Bus header (IPMB_1)

10 PSU SMBus (PSU_SMB1)

11 TPM Header (TPM1)

12 Thermal Sensor header (TR1)

13 Front Lan LED Connector (FRONT_LED_LAN34)

14 2 x 240-pin DDR3 DIMM Slots

(DDR3_F2, DDR3_E2, White)

15 2 x 240-pin DDR3 DIMM Slots

(DDR3_F1, DDR3_E1, Blue)

16 ATX 12V Power Connector (ATX12V_1)

17 CPU Fan Connector (CPU2_FAN)

18 Front Fan Connector (FRNT_FAN4)

19 Front Fan Connector (FRNT_FAN3)

20 2011-Pin CPU Socket (CPU_AP1)

21 2 x 240-pin DDR3 DIMM Slots

(DDR3_H2, DDR3_G2, White)

22 2 x 240-pin DDR3 DIMM Slots

(DDR3_A1, DDR3_B1, Blue)

23 2011-Pin CPU Socket (CPU_BSP1)

24 Front Fan Connector (FRNT_FAN2)

25 Front Fan Connector (FRNT_FAN1)

26 CPU Fan Connector (CPU1_FAN)

27 ATX 12V Power Connector (ATX12V1)

28 2 x 240-pin DDR3 DIMM Slots

(DDR3_D2, DDR3_C2, White)

29 2 x 240-pin DDR3 DIMM Slots

(DDR3_C1, DDR3_D1, Blue)

32

30 USB 2.0 Header (USB_5_6)

31 USB 2.0 Port (USB_8)

32 Speaker Header (SPEAKER1)

33

SATA SGPIO Connector (SATA_SGPIO1)

34 SATA2 Connector (SATAII_PORT_0)

35 SCU Connector (SCU_PORT_0)

36 SATA3 Connector (SATA

III_1)

37 SATA3 Connector (SATA

III_0)

38 BMC SMB Header (BMC_SMB1)

39 BMC SMB Header (BMC_SMB3)

40 2 x 240-pin DDR3 DIMM Slots

(DDR3_A2, DDR3_B2, White)

41 2 x 240-pin DDR3 DIMM Slots

(DDR3_H1, DDR3_G1, Blue)

42 Rear Fan Connector (REAR_FAN2)

43 Rear Fan Connector (REAR_FAN1)

33

EP2C602-2L+O/D16

30.5cm (12 in)

Intel

C602

ATXP WR1

DDR3 _F2 (6 4 bit, 24 0-pi n modul e)

DDR3 _F1 (6 4 bit, 24 0-pi n modul e)

DDR3 _E2 (6 4 bit, 24 0-pi n modul e)

DDR3 _E1 (6 4 bit, 24 0-pi n modul e)

EP 2C 602-2 L+ O/ D1 6

ATX12V_ 1

Top:
MNG_ LAN

USB 2.0
T: USB 3
B: U SB4

LAN1

VGA 1

COM 1

CMO S

Bat tery

Ro H S

Dr.

Deb ug

PCIE7

USB _8

1

TR1

FRONT_LED_ LAN34

HDLED RESET

PLED PWRBT N

PANEL1

USB_5 _6

1

COM2

1

TPM1

1

NMI_BTN1

1

AUX_PANE L1

1

ME_RECOV ERY1

1

IPMB_1

1

SATA_SGPIO1

1

BMC
ROM

BUZZER 1

64Mb
BIOS

SATAIII_0

SATAIII_1

SATAII_

PORT_ 0

FRNT_FA N4

PCIE6

4

5

1

2

3 6

7

9

8

12

1

PSU_S MB1

14

10

11

13

15

32

35

34 33

37

36

1

SPEAKER1

DDR3 _C1 (6 4 bit, 24 0-pi n modul e)

DDR3 _C2 (6 4 bit, 24 0-pi n modul e)

DDR3 _D1 (6 4 bit, 24 0-pi n modul e)

DDR3 _D2 (6 4 bit, 24 0-pi n modul e)

DDR3 _G1 (6 4 bit, 24 0-pi n modul e)

DDR3 _G2 (6 4 bit, 24 0-pi n modul e)

DDR3 _H1 (6 4 bit, 24 0-pi n modul e)

DDR3 _H2 (6 4 bit, 24 0-pi n modul e)

DDR3 _B2 (6 4 bit, 24 0-pi n modul e)

DDR3 _B1 (6 4 bit, 24 0-pi n modul e)

DDR3 _A2 (6 4 bit, 24 0-pi n modul e)

DDR3 _A1 (6 4 bit, 24 0-pi n modul e)

ATX12V1

FRNT_FA N3

CPU2_FA N

FRNT_FA N1

CPU1_FA N

FRNT_FA N2

REAR_FA N1

REAR_FA N2

USB 2.0
T: USB 1
B: U SB2

LAN2

UID_LE D1

UID_SW

SCU_PO RT_0

1

12V_SW1

1

1

BMC_SMB _1

1

BMC_SMB _3

1

3031

29

26

25

24

23

22

21

18

17

16

20

28

27

19

38

39

40

41

42

43

LAN3

33.0cm (13 i n)

34

1 Dr. Debug

2 ME Recovery Jumper (ME_RECOVERY1)

3 Non Maskable Interrupt Button (NMI_BTN1)

4

Auxiliary panel header (AUX_PANEL1)

5 System Panel Header (PANEL1)

6 -12V Switch Header (12V_SW1)

7 COM Port Header (COM2)

8 ATX Power Connector (ATXPWR1)

9 Intelligent Platform Management Bus header (IPMB_1)

10 PSU SMBus (PSU_SMB1)

11 TPM Header (TPM1)

12 Thermal Sensor header (TR1)

13 Front Lan LED Connector (FRONT_LED_LAN34)

14 2 x 240-pin DDR3 DIMM Slots

(DDR3_F2, DDR3_E2, White)

15 2 x 240-pin DDR3 DIMM Slots

(DDR3_F1, DDR3_E1, Blue)

16 ATX 12V Power Connector (ATX12V_1)

17 CPU Fan Connector (CPU2_FAN)

18 Front Fan Connector (FRNT_FAN4)

19 Front Fan Connector (FRNT_FAN3)

20 2011-Pin CPU Socket (CPU_AP1)

21 2 x 240-pin DDR3 DIMM Slots

(DDR3_H2, DDR3_G2, White)

22 2 x 240-pin DDR3 DIMM Slots

(DDR3_A1, DDR3_B1, Blue)

23 2011-Pin CPU Socket (CPU_BSP1)

24 Front Fan Connector (FRNT_FAN2)

25 Front Fan Connector (FRNT_FAN1)

26 CPU Fan Connector (CPU1_FAN)

27 ATX 12V Power Connector (ATX12V1)

28 2 x 240-pin DDR3 DIMM Slots

(DDR3_D2, DDR3_C2, White)

29 2 x 240-pin DDR3 DIMM Slots

(DDR3_C1, DDR3_D1, Blue)

35

30 USB 2.0 Header (USB_5_6)

31 USB 2.0 Port (USB_8)

32 Speaker Header (SPEAKER1)

33

SATA SGPIO Connector (SATA_SGPIO1)

34 SATA2 Connector (SATAII_PORT_0)

35 SCU Connector (SCU_PORT_0)

36 SATA3 Connector (SATA

III_1)

37 SATA3 Connector (SATA

III_0)

38 BMC SMB Header (BMC_SMB1)

39 BMC SMB Header (BMC_SMB2)

40 2 x 240-pin DDR3 DIMM Slots

(DDR3_A2, DDR3_B2, White)

41 2 x 240-pin DDR3 DIMM Slots

(DDR3_H1, DDR3_G1, Blue)

42 Rear Fan Connector (REAR_FAN2)

43 Rear Fan Connector (REAR_FAN1)

36

EP2C602-2L+/D16

30.5cm (12 in)

Intel

C602

ATXP WR1

DDR3 _F2 (6 4 bit, 24 0-pi n modul e)

DDR3 _F1 (6 4 bit, 24 0-pi n modul e)

DDR3 _E2 (6 4 bit, 24 0-pi n modul e)

DDR3 _E1 (6 4 bit, 24 0-pi n modul e)

EP 2C 602-2 L+ /D 16

ATX12V_ 1

Top:
MNG_ LAN

USB 2.0
T: USB 3
B: U SB4

LAN1

VGA 1

COM 1

CMO S

Bat tery

Ro H S

Dr.

Deb ug

PCIE7

USB _8

1

TR1

FRONT_LED_ LAN34

HDLED RESET

PLED PWRBT N

PANEL1

USB_5 _6

1

COM2

1

TPM1

1

NMI_BTN1

1

AUX_PANE L1

1

ME_RECOV ERY1

1

IPMB_1

1

SATA_SGPIO1

1

BMC
ROM

BUZZER 1

64Mb
BIOS

SATAIII_0

SATAIII_1

SATAII_

PORT_ 0

FRNT_FA N4

PCIE6

4

5

1

2

3 6

7

9

8

12

1

PSU_S MB1

14

10

11

13

15

32

35

34 33

37

36

1

SPEAKER1

DDR3 _C1 (6 4 bit, 24 0-pi n modul e)

DDR3 _C2 (6 4 bit, 24 0-pi n modul e)

DDR3 _D1 (6 4 bit, 24 0-pi n modul e)

DDR3 _D2 (6 4 bit, 24 0-pi n modul e)

DDR3 _G1 (6 4 bit, 24 0-pi n modul e)

DDR3 _G2 (6 4 bit, 24 0-pi n modul e)

DDR3 _H1 (6 4 bit, 24 0-pi n modul e)

DDR3 _H2 (6 4 bit, 24 0-pi n modul e)

DDR3 _B2 (6 4 bit, 24 0-pi n modul e)

DDR3 _B1 (6 4 bit, 24 0-pi n modul e)

DDR3 _A2 (6 4 bit, 24 0-pi n modul e)

DDR3 _A1 (6 4 bit, 24 0-pi n modul e)

ATX12V1

FRNT_FA N3

CPU2_FA N

FRNT_FA N1

CPU1_FA N

FRNT_FA N2

REAR_FA N1

REAR_FA N2

USB 2.0
T: USB 1
B: U SB2

LAN2

UID_LE D1

UID_SW

SCU_PO RT_0

1

12V_SW1

1

1

BMC_SMB _1

1

BMC_SMB _3

1

3031

29

26

25

24

23

22

21

18

17

16

20

28

27

19

38

39

40

41

42

43

33.0cm (13 i n)

37

1 Dr. Debug

2 ME Recovery Jumper (ME_RECOVERY1)

3 Non Maskable Interrupt Button (NMI_BTN1)

4

Auxiliary panel header (AUX_PANEL1)

5 System Panel Header (PANEL1)

6 -12V Switch Header (12V_SW1)

7 COM Port Header (COM2)

8 ATX Power Connector (ATXPWR1)

9 Intelligent Platform Management Bus header (IPMB_1)

10 PSU SMBus (PSU_SMB1)

11 TPM Header (TPM1)

12 Thermal Sensor header (TR1)

13 Front Lan LED Connector (FRONT_LED_LAN34)

14 2 x 240-pin DDR3 DIMM Slots

(DDR3_F2, DDR3_E2, White)

15 2 x 240-pin DDR3 DIMM Slots

(DDR3_F1, DDR3_E1, Blue)

16 ATX 12V Power Connector (ATX12V_1)

17 CPU Fan Connector (CPU2_FAN)

18 Front Fan Connector (FRNT_FAN4)

19 Front Fan Connector (FRNT_FAN3)

20 2011-Pin CPU Socket (CPU_AP1)

21 2 x 240-pin DDR3 DIMM Slots

(DDR3_H2, DDR3_G2, White)

22 2 x 240-pin DDR3 DIMM Slots

(DDR3_A1, DDR3_B1, Blue)

23 2011-Pin CPU Socket (CPU_BSP1)

24 Front Fan Connector (FRNT_FAN2)

25 Front Fan Connector (FRNT_FAN1)

26 CPU Fan Connector (CPU1_FAN)

27 ATX 12V Power Connector (ATX12V1)

28 2 x 240-pin DDR3 DIMM Slots

(DDR3_D2, DDR3_C2, White)

29 2 x 240-pin DDR3 DIMM Slots

(DDR3_C1, DDR3_D1, Blue)

38

30 USB 2.0 Header (USB_5_6)

31 USB 2.0 Port (USB_8)

32 Speaker Header (SPEAKER1)

33

SATA SGPIO Connector (SATA_SGPIO1)

34 SATA2 Connector (SATAII_PORT_0)

35 SCU Connector (SCU_PORT_0)

36 SATA3 Connector (SATA

III_1)

37 SATA3 Connector (SATA

III_0)

38 BMC SMB Header (BMC_SMB1)

39 BMC SMB Header (BMC_SMB2)

40 2 x 240-pin DDR3 DIMM Slots

(DDR3_A2, DDR3_B2, White)

41 2 x 240-pin DDR3 DIMM Slots

(DDR3_H1, DDR3_G1, Blue)

42 Rear Fan Connector (REAR_FAN2)

43 Rear Fan Connector (REAR_FAN1)

39

EP2C602-S6/D16

30.5cm (12 in)

Intel

C602

ATXP WR1

DDR3 _F2 (6 4 bit, 24 0-pi n modul e)

DDR3 _F1 (6 4 bit, 24 0-pi n modul e)

DDR3 _E2 (6 4 bit, 24 0-pi n modul e)

DDR3 _E1 (6 4 bit, 24 0-pi n modul e)

EP 2C 602-S 6/ D1 6

ATX12V_ 1

Top:
MNG_ LAN

USB 2.0
T: USB 3
B: U SB4

LAN1

VGA 1

COM 1

CMO S

Bat tery

Ro H S

Dr.

Deb ug

PCIE7

USB _8

1

TR1

FRONT_LED_ LAN34

HDLED RESET

PLED PWRBT N

PANEL1

USB_5 _6

1

COM2

1

TPM1

1

NMI_BTN1

1

AUX_PANE L1

1

ME_RECOV ERY1

1

IPMB_1

1

SATA_SGPIO1

1

BMC
ROM

BUZZER 1

64Mb
BIOS

SATAIII_0

SATAIII_1

SATAII_

PORT_ 0

FRNT_FA N4

PCIE6

4

5

1

2

3 6

7

9

8

12

1

PSU_S MB1

14

10

11

13

15

32

35

34 33

36

394037

38

1

SPEAKER1

DDR3 _C1 (6 4 bit, 24 0-pi n modul e)

DDR3 _C2 (6 4 bit, 24 0-pi n modul e)

DDR3 _D1 (6 4 bit, 24 0-pi n modul e)

DDR3 _D2 (6 4 bit, 24 0-pi n modul e)

DDR3 _G1 (6 4 bit, 24 0-pi n modul e)

DDR3 _G2 (6 4 bit, 24 0-pi n modul e)

DDR3 _H1 (6 4 bit, 24 0-pi n modul e)

DDR3 _H2 (6 4 bit, 24 0-pi n modul e)

DDR3 _B2 (6 4 bit, 24 0-pi n modul e)

DDR3 _B1 (6 4 bit, 24 0-pi n modul e)

DDR3 _A2 (6 4 bit, 24 0-pi n modul e)

DDR3 _A1 (6 4 bit, 24 0-pi n modul e)

ATX12V1

FRNT_FA N3

CPU2_FA N

FRNT_FA N1

CPU1_FA N

FRNT_FA N2

REAR_FA N1

REAR_FA N2

USB 2.0
T: USB 1
B: U SB2

LAN2

UID_LE D1

UID_SW

LSI_SA S_0

SCU_

PORT_ 0

LSI_SA S_1

SAS 2 .0

1

12V_SW1

1

1

BMC_SMB _1

1

BMC_SMB _3

1

3031

29

26

25

24

23

22

21

18

17

16

20

28

27

19

41

42

43

44

45

33.0cm (13 i n)

40

1 Dr. Debug

2 ME Recovery Jumper (ME_RECOVERY1)

3 Non Maskable Interrupt Button (NMI_BTN1)

4

Auxiliary panel header (AUX_PANEL1)

5 System Panel Header (PANEL1)

6 -12V Switch Header (12V_SW1)

7 COM Port Header (COM2)

8 ATX Power Connector (ATXPWR1)

9 Intelligent Platform Management Bus header (IPMB_1)

10 PSU SMBus (PSU_SMB1)

11 TPM Header (TPM1)

12 Thermal Sensor header (TR1)

13 Front Lan LED Connector (FRONT_LED_LAN34)

14 2 x 240-pin DDR3 DIMM Slots

(DDR3_F2, DDR3_E2, White)

15 2 x 240-pin DDR3 DIMM Slots

(DDR3_F1, DDR3_E1, Blue)

16 ATX 12V Power Connector (ATX12V_1)

17 CPU Fan Connector (CPU2_FAN)

18 Front Fan Connector (FRNT_FAN4)

19 Front Fan Connector (FRNT_FAN3)

20 2011-Pin CPU Socket (CPU_AP1)

21 2 x 240-pin DDR3 DIMM Slots

(DDR3_H2, DDR3_G2, White)

22 2 x 240-pin DDR3 DIMM Slots

(DDR3_A1, DDR3_B1, Blue)

23 2011-Pin CPU Socket (CPU_BSP1)

24 Front Fan Connector (FRNT_FAN2)

25 Front Fan Connector (FRNT_FAN1)

26 CPU Fan Connector (CPU1_FAN)

27 ATX 12V Power Connector (ATX12V1)

28 2 x 240-pin DDR3 DIMM Slots

(DDR3_D2, DDR3_C2, White)

29 2 x 240-pin DDR3 DIMM Slots

(DDR3_C1, DDR3_D1, Blue)

41

30 USB 2.0 Header (USB_5_6)

31 USB 2.0 Port (USB_8)

32 Speaker Header (SPEAKER1)

33 SATA SGPIO Connector (SATA_SGPIO1)

34 SATA2 Connector (SATAII_PORT_0)

35 SCU Connector (SCU_PORT_0)

36 LSI SAS Connector (LSI_SAS_0

)

37 LSI SAS Connector (LSI_SAS_1

)

38 SATA3 Connector (SATA

III_1)

39 SATA3 Connector (SATA

III_0)

40 BMC SMB Header (BMC_SMB1)

41 BMC SMB Header (BMC_SMB3)

42 2 x 240-pin DDR3 DIMM Slots

(DDR3_A2, DDR3_B2, White)

43 2 x 240-pin DDR3 DIMM Slots

(DDR3_H1, DDR3_G1, Blue)

44 Rear Fan Connector (REAR_FAN2)

45 Rear Fan Connector (REAR_FAN1)

42

1.4 I/O Panel

EP2C602-2T2OS6/D16

1 Serial Port (COM1)

2 Management LAN Port (MNG_LAN)*

3 10G SFP+ LAN Port (LAN4)**

4 10G SFP+ LAN Port (LAN3)**

5 10G LAN Port (LAN2)

6 10G LAN Port (LAN1)

7 USB 2.0 Ports (USB_3_4)

8 D-Sub Port (VGA1)

9 USB 2.0 Ports (USB_1_2)

* There are two LEDs on each LAN port. Please refer to the table below for the LAN

port LED indications.

ACT/LINK

LED

SPEED

LED

LAN Port

LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description
Off No Link Off 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Cable Connection Green 1Gbps connection

1

2

5

6

7

89

4

3

** There are two LEDs on each Optical LAN port. Please refer to the table below for

the Optical LAN port LED indications.

ACT/LINK

LED

SPEED

LED

Optical LAN Port

Optical LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description
Off No Link Off No Link
Blinking Data Activity Green 10Gbps connection
On Cable Connection

43

EP2C602-2TS6/D16

1 Serial Port (COM1)

2 Management LAN Port (MNG_LAN)*

3 10G LAN Port (LAN2)

4 10G LAN Port (LAN1)

5 USB 2.0 Ports (USB_3_4)

6 D-Sub Port (VGA1)

7 USB 2.0 Ports (USB_1_2)

* There are two LEDs on each LAN port. Please refer to the table below for the LAN

port LED indications.

ACT/LINK

LED

SPEED

LED

LAN Port

LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description
Off No Link Off 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Cable Connection Green 1Gbps connection

1

2

4

3

5

6

7

44

EP2C602-2L+2OS6/D16

1 Serial Port (COM1)

2 Management LAN Port (MNG_LAN)*

3 10G SFP+ LAN Port (LAN4)**

4 10G SFP+ LAN Port (LAN3)**

5 1G LAN Port (LAN2)

6 1G LAN Port (LAN1)

7 USB 2.0 Ports (USB_3_4)

8 D-Sub Port (VGA1)

9 USB 2.0 Ports (USB_1_2)

* There are two LEDs on each LAN port. Please refer to the table below for the LAN

port LED indications.

ACT/LINK

LED

SPEED

LED

LAN Port

LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description
Off No Link Off 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Cable Connection Green 1Gbps connection

1

2

5

6

7

89

4

3

** There are two LEDs on each Optical LAN port. Please refer to the table below for

the Optical LAN port LED indications.

ACT/LINK

LED

SPEED

LED

Optical LAN Port

Optical LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description
Off No Link Off No Link
Blinking Data Activity Green 10Gbps connection
On Cable Connection

45

EP2C602-2L+OS6/D16

* There are two LEDs on each LAN port. Please refer to the table below for the LAN

port LED indications.

ACT/LINK

LED

SPEED

LED

LAN Port

LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description
Off No Link Off 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Cable Connection Green 1Gbps connection

1 Serial Port (COM1)

2 Management LAN Port (MNG_LAN)*

3 10G SFP+ LAN Port (LAN3)**

4 1G LAN Port (LAN2)

5 1G LAN Port (LAN1)

6 USB 2.0 Ports (USB_3_4)

7 D-Sub Port (VGA1)

8 USB 2.0 Ports (USB_1_2)

3

1

2

4

5

6

7

8

** There are two LEDs on each Optical LAN port. Please refer to the table below for

the Optical LAN port LED indications.

ACT/LINK

LED

SPEED

LED

Optical LAN Port

Optical LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description
Off No Link Off No Link
Blinking Data Activity Green 10Gbps connection
On Cable Connection

46

EP2C602-2OS6/D16

1 Serial Port (COM1)

2 Management LAN Port (MNG_LAN)*

3 10G SFP+ LAN Port (LAN4)**

4 10G SFP+ LAN Port (LAN3)**

5 USB 2.0 Ports (USB_3_4)

6 D-Sub Port (VGA1)

7 USB 2.0 Ports (USB_1_2)

* There are two LEDs on each LAN port. Please refer to the table below for the LAN

port LED indications.

ACT/LINK

LED

SPEED

LED

LAN Port

LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description
Off No Link Off 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Cable Connection Green 1Gbps connection

1

2

5

6

7

4

3

** There are two LEDs on each Optical LAN port. Please refer to the table below for

the Optical LAN port LED indications.

ACT/LINK

LED

SPEED

LED

Optical LAN Port

Optical LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description
Off No Link Off No Link
Blinking Data Activity Green 10Gbps connection
On Cable Connection

47

EP2C602-2T/D16

* There are two LEDs on each LAN port. Please refer to the table below for the LAN

port LED indications.

ACT/LINK

LED

SPEED

LED

LAN Port

LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description
Off No Link Off 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Cable Connection Green 1Gbps connection

1 Serial Port (COM1)

2 Management LAN Port (MNG_LAN)*

3 10G LAN Port (LAN2)

4 10G LAN Port (LAN1)

5 USB 2.0 Ports (USB_3_4)

6 D-Sub Port (VGA1)

7 USB 2.0 Ports (USB_1_2)

1

2

4

3

5

6

7

48

EP2C602-2O/D16

1 Serial Port (COM1)

2 Management LAN Port (MNG_LAN)*

3 10G SFP+ LAN Port (LAN4)**

4 10G SFP+ LAN Port (LAN3)**

5 USB 2.0 Ports (USB_3_4)

6 D-Sub Port (VGA1)

7 USB 2.0 Ports (USB_1_2)

* There are two LEDs on each LAN port. Please refer to the table below for the LAN

port LED indications.

ACT/LINK

LED

SPEED

LED

LAN Port

LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description
Off No Link Off 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Cable Connection Green 1Gbps connection

1

2

5

6

7

4

3

** There are two LEDs on each Optical LAN port. Please refer to the table below for

the Optical LAN port LED indications.

ACT/LINK

LED

SPEED

LED

Optical LAN Port

Optical LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description
Off No Link Off No Link
Blinking Data Activity Green 10Gbps connection
On Cable Connection

49

EP2C602-O/D16

1 Serial Port (COM1)

2 Management LAN Port (MNG_LAN)*

3 10G SFP+ LAN Port (LAN3)**

4 USB 2.0 Ports (USB_3_4)

5 D-Sub Port (VGA1)

6 USB 2.0 Ports (USB_1_2)

* There are two LEDs on each LAN port. Please refer to the table below for the LAN

port LED indications.

ACT/LINK

LED

SPEED

LED

LAN Port

LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description
Off No Link Off 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Cable Connection Green 1Gbps connection

1

2

4

5

6

3

** There are two LEDs on each Optical LAN port. Please refer to the table below for

the Optical LAN port LED indications.

ACT/LINK

LED

SPEED

LED

Optical LAN Port

Optical LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description
Off No Link Off No Link
Blinking Data Activity Green 10Gbps connection
On Cable Connection

50

EP2C602-2L+O/D16

* There are two LEDs on each LAN port. Please refer to the table below for the LAN

port LED indications.

ACT/LINK

LED

SPEED

LED

LAN Port

LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description
Off No Link Off 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Cable Connection Green 1Gbps connection

1 Serial Port (COM1)

2 Management LAN Port (MNG_LAN)*

3 10G SFP+ LAN Port (LAN3)**

4 1G LAN Port (LAN2)

5 1G LAN Port (LAN1)

6 USB 2.0 Ports (USB_3_4)

7 D-Sub Port (VGA1)

8 USB 2.0 Ports (USB_1_2)

1

2

4

5

6

7

8

3

** There are two LEDs on each Optical LAN port. Please refer to the table below for

the Optical LAN port LED indications.

ACT/LINK

LED

SPEED

LED

Optical LAN Port

Optical LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description
Off No Link Off No Link
Blinking Data Activity Green 10Gbps connection
On Cable Connection

51

EP2C602-2L+/D16

* There are two LEDs on each LAN port. Please refer to the table below for the LAN

port LED indications.

ACT/LINK

LED

SPEED

LED

LAN Port

LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description
Off No Link Off 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Cable Connection Green 1Gbps connection

1 Serial Port (COM1)

2 Management LAN Port (MNG_LAN)*

3 1G LAN Port (LAN2)

4 1G LAN Port (LAN1)

5 USB 2.0 Ports (USB_3_4)

6 D-Sub Port (VGA1)

7 USB 2.0 Ports (USB_1_2)

1

2

4

3

5

6

7

52

EP2C602-S6/D16

* There are two LEDs on each LAN port. Please refer to the table below for the LAN

port LED indications.

ACT/LINK

LED

SPEED

LED

LAN Port

LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description
Off No Link Off 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Cable Connection Green 1Gbps connection

1 Serial Port (COM1)

2 Management LAN Port (MNG_LAN)*

3 1G LAN Port (LAN2)

4 1G LAN Port (LAN1)

5 USB 2.0 Ports (USB_3_4)

6 D-Sub Port (VGA1)

7 USB 2.0 Ports (USB_1_2)

1

2

4

3

5

6

7

53

1.5 Block Diagram

1

Sandy Bridge-E

Joufm!Qspdfttps

Ijhi.Tqffe!VTC

8!qpsut

MHB.3122!Qjo!Tpdlfu

DQV3

591Nc0t

Rvbe.Diboofm!Nfnpsz!y9!Tmput

DI!E

EES4!21770244402711

EES4!21770244402711

EES4!21770244402711

EES4!21770244402711

Sandy Bridge-E

Joufm!Qspdfttps

MHB.3122!Qjo!Tpdlfu

DQV2

RQJ

DI!D

DI!C

DI!B

DI!E

DI!D

DI!C

DI!B

EES4!21770244402711

EES4!21770244402711

EES4!21770244402711

EES4!21770244402711

Rvbe.Diboofm!Nfnpsz!y9!Tmput

PatsburgPCH

QDJ.F!4!Y27!TMPU!!QDJF8

QDJ.F!4!Y27!TMPU!!QDJF7

MQD!CVT

SIO

NCT6776D

TBUB3`2

TBUB4`1

SPI FLASH

64Mb

TQJ

TBUB3`3TBUB3`1

TBUB4`2

TBUB3`4

TBUB!CVT

C N D !

C N D !C N D !

C N D !

B T U 341 1

B T U 341 1B T U 341 1

B T U 341 1

ODTJ

QDJFy2

N H N U!9 322 D M

N H N U!9 322 D MN H N U!9 322 D M

N H N U!9 322 D M

QDJF

QDJF

ENJ

936::!Y9

MTJ!3419!Y9

TDV`QPSU`3

TDV`QPSU`2TDV`QPSU`1

TDV`QPSU`4

TDV!CVT

QDJF

Y6510J461.CU3!!Y9

Njoj!9198!dpoofdups

Njoj!9198!dpoofdups

INTEL

54

Chapter 2: Installation

Before you install the motherboard, study the conguration of your chassis

to ensure that the motherboard ts into it.

EP2C602 Series are dual socket motherboards that support Intel® Xeon®

E5-2400/1400 Series Processors. Please install a primary processor

(BootStrap Processor) into “CPU_BSP1” socket and then install a non-

Primary Processor (Application Processors) into “CPU_AP1” socket.

*For a single CPU, please install it into “CPU_BSP1” socket (framed by a

square).

2.1 Pre-installation Precautions

Take note of the following precautions before you install motherboard com-

ponents or change any motherboard settings.

1. Make sure to unplug the power cord before installing or

removing the motherboard. Failure to do so may cause

physical injuries to you and damages to motherboard com-

ponents.

2. In order to avoid damage from static electricity to the moth-

erboard’s components, NEVER place your motherboard

directly on a carpet. Also remember to use a grounded wrist

strap or touch a safety grounded object before you handle

the components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any components, place them on a

grounded anti-static pad or in the bag that comes with the

components.

5. When placing screws to secure the motherboard to the

chassis, please do not over-tighten the screws! Doing so

may damage the motherboard.

2.2 Screw Holes

Place screws into the holes indicated by circles to secure the motherboard

to the chassis.

55

2.3 CPU Installation

For the installation of Intel 2011-Pin CPU,

please follow the steps below.

Before you insert the 2011-Pin CPU into the socket, please check if the

CPU surface is unclean or if there are any bent pins in the socket. Do

not force to insert the CPU into the socket if above situation is found.

Otherwise, the CPU will be seriously damaged.

Step 1. Open the socket:

Step 1-1. Disengage the left lever by pressing it

down and sliding it out of the hook.

Step 1-2. Disengage the right lever by pressing

it down and sliding it out of the hook.

Step 1-3. Keep the right lever positioned at

about 90 degrees in order to ip up

the load plate.

Step 2. Insert the 2011-Pin CPU:

Step 2-1. Hold the CPU by the edge with the

triangle mark(Pin 1) on your upper

right corner.

2011-Pin Socket Overview

Conta ct Array

Socke t Body

Load Le ver

Load Le ver

Load Pl ate

Pin1

56

Step 2-2. Locate Pin1 and the two orientation

key notches.

alignment key

alignment key

Pin1

2011-Pin CPU 2011-Pin Socket

For proper inserting, please ensure to match the four orientation key

notches of the CPU with the four alignment keys of the socket.

Step 2-3. Careful l y place t h e CPU in t o the

socket by using a purely vertical mo-

tion.

Step 2-4. Verify that the CPU is within the sock-

et and properly mated to the orient

keys.

Step 3. Close the socket:

Step 3-1. Flip the load plate onto the IHS, then

the cover will automatically come off

by itself.

The cover must be placed if returning the

motherboard for after service.

Step 3-2. Press down the right load lever, and

secure it with the load plate tab under

the retention tab.

Step 3-3. Press down the left load lever, and

secure it with the load plate tab under

the retention tab.

orientation key notch

orientation key notch

57

2.4 Installation of CPU Fan and Heatsink

This motherboard is equipped with 2011-Pin socket that supports Intel 2011-Pin

CPU. Please adopt the type of heatsink and cooling fan compliant with Intel 2011-

Pin CPU to dissipate heat. Before you installed the heatsink, you need to spray

thermal interface material between the CPU and the heatsink to improve heat dis-

sipation. Ensure that the CPU and the heatsink are securely fastened and in good

contact with each other. Then connect the CPU fan to the CPU_FAN connector.

For proper installation, please kindly refer to the instruction manuals of your

CPU fan and heatsink.

Below is an example to illustrate the installation of the heatsink for 2011-Pin CPU.

Step 1. Apply thermal interface material onto center of

IHS on the socket surface.

Step 2. Place the heatsink onto the socket. Ensure fan

cables are oriented on side closest to the CPU

fan connector on the motherboard.

Step 3. Align screws with the motherboard’s holes.

Step 4. Use a screw driver to install the screws.

If you don’t fasten the screws, the heatsink cannot be secured on

the motherboard.

Step 5. Connect fan header with the CPU fan connector on the motherboard.

Step 6. Secure excess cable with tie-wrap to ensure the cable does not interfere

with fan operation or contact other components.

App ly Therm al
Int erfac e Mater ial

Scre ws
(4 cor ners)

58

2.5 Installation of Memory Modules (DIMM)

This motherboard provides four 240-pin DDR3 (Double Data Rate 3) DIMM

slots, and supports Dual Channel Memory Technology. For dual channel
configuration, you always need to install two identical (the same brand,

speed, size and chip-type) memory modules in the DDR3 DIMM slots to

activate Dual Channel Memory Technology. Otherwise, it will operate at
single channel mode.

1. It is not allowed to install a DDR or DDR2 memory
module into a DDR3 slot; otherwise, this motherboard
and DIMM may be damaged.

2. If you install only one memory module or two non
identical memory modules, it is unable to activate Dual
Channel Memory Technology.

3. Some DDR3 1GB double-sided DIMMs with 16 chips
may not work on this motherboard. It is not
recommended to install them on this motherboard.

4. A single memory module should be installed in the blue
socket.

5. If you install only one CPU (CPU_BSP1) on the moth-
erboard, make sure to install DIMMs into DDR3_A,
DDR3_B, DDR3_C, or DDR3_D slot(s).

59

Installing a DIMM

Please make sure to disconnect the power supply before add-

ing or removing DIMMs or system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM

matches the break on the slot.

The DIMM only ts in one correct orientation. It will cause per-

manent damage to the motherboard and the DIMM if you force

the DIMM into the slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both

ends fully snap back in place and the DIMM is properly seated.

60

2.6 Expansion Slots (PCI Express Slots)

There are 2 PCI Express slots on the motherboard.

PCIE slots:

PCIE6 and PCIE7 (PCIE 3.0 x16 slot) are used for PCI Express

x16 lane width graphics cards.

Please note that PCIE6 is available ONLY when the rst CPU

(CPU_BSP1) is installed, and PCIE7 is available ONLY when

the second CPU (CPU_AP1) is installed.

Installing an expansion card

Step 1. Before installing an expansion card, please make sure that the

power supply is switched off or the power cord is unplugged.

Please read the documentation of the expansion card and make

necessary hardware settings for the card before you start the

installation.

Step 2. Remove the system unit cover (if your motherboard is already

installed in a chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep

the screws for later use.

Step 4. Align the card connector with the slot and press rmly until the

card is completely seated on the slot.

Step 5. Fasten the card to the chassis with screws.

Step 6. Replace the system cover.

61

2.7 Jumpers Setup

The illustr ation shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap

is placed on pins, the jumper is “Open”. The

illustration shows a 3-pin jumper whose

pin1 and pin2 are “Short” when jumper cap

is placed on these 2 pins.

ME Recovery Jumper

(3-pin ME_RECOVERY1)

1-2:

Default

2-3:

ME recovery mode

-12V Switch Header

(3-pin 12V_SW1)

1-2:

Default

2-3:

PSU (-12V)

62

Serial ATA2 Connector

(SATAII_PORT_0)

Serial ATA3 Connectors

(SATA

III

_0)

(SATA

III

_1)

2.8 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT

place jumper caps over these headers and connectors. Plac-

ing jumper caps over the headers and connectors will cause

permanent damage to the motherboard!

This Serial ATA2 (SATA2)

connector supports SATA

data cables for internal stor-

age devices. The current

SATA2 interface allows up to

3.0 Gb/s data transfer rate.

These two Serial ATA3

(SATA3) connectors sup-

port SATA data cables for

internal storage devices.

The current SATA3 interface

allows up to 6.0 Gb/s data

transfer rate.

SATAIII_0

SATAIII_1

SATAII_PORT_0

SAS Connectors

(For EP2C602-2T2OS6/D16 /

EP2C602-2TS6/D16 /

EP2C602-2OS6/D16 /

EP2C602-S6/D16)

(LSI_SAS_0)

(LSI_SAS_1)

These two SAS connectors

support SAS/SATA data

cables for internal storage

devices. The current SAS2/

SATA3 interface allows up

to 6.0 Gb/s data transfer

rate. For connecting SAS

HDDs, please contact SAS

data cable dealers.

LSI_SAS_1

LSI_SAS_0

63

SCU Connector

(SCU_PORT_0)

This SCU connector sup-

ports SAS/SATA data cables

for internal storage devices.

The current SAS2/SATA3

interface allows up to 6.0

Gb/s data transfer rate. For

connecting SAS HDDs,

please contact SAS data

cable dealers.

SCU_PORT_0

USB 2.0 Header

and Port

(9-pin USB_5_6)

(USB_8)

DUMMY

GND

GND

+B

-B

USB_P WR

+A

-A

USB_P WR

1

Besides four default USB 2.0

ports on the I/O panel, there

is one USB 2.0 header and

one port on this mother-

board. This USB 2.0 header

can support two USB 2.0

ports.

TPM Header

(17-pin TPM1)

This connector supports

Trusted Platform Module

(TPM) system, which can

securely store keys, digital

certicates, passwords, and

data. A TPM system also

helps enhance network se-

curity, protects digital identi-

ties, and ensures platform

integrity.

1

GND

SMB _DA TA_ MAI N

LAD 2

LAD 1

GND

S_P WRD WN#

SER IRQ #

GND

PCI CLK

PCI RST #

LAD 3

+3V

LAD 0

+3V SB

GND

FRA ME

SMB _CL K_M AIN

System Panel Header

(9-pin PANEL1)

This header accommodates

several system front panel

functions.

64

Connect the power switch, reset switch and system status indica-

tor on the chassis to this header according to the pin assignments

below. Note the positive and negative pins before connecting the

cables.

PWRBTN (Power Switch):

Connect to the power switch on the chassis front panel. You may

congure the way to turn off your system using the power switch.

RESET (Reset Switch):

Connect to the reset switch on the chassis front panel. Press the

reset switch to restart the computer if the computer freezes and

fails to perform a normal restart.

PLED (System Power LED):

Connect to the power status indicator on the chassis front panel.

The LED is on when the system is operating. The LED keeps

blinking when the sys-tem is in S1/S3 sleep state. The LED is off

when the system is in S4 sleep state or powered off (S5).

HDLED (Hard Drive Activity LED):

Connect to the hard drive activity LED on the chassis front panel.

The LED is on when the hard drive is reading or writing data.

The front panel design may differ by chassis. A front panel mod-

ule mainly consists of power switch, reset switch, power LED,

hard drive activity LED, speaker and etc. When connecting your

chassis front panel module to this header, make sure the wire as-

signments and the pin assignments are matched correctly.

Auxiliary Panel Header

(18-pin AUX_PANEL1)

This header supports mul-

tiple functions on the front

panel, including front panel

SMB, internet status indica-

tor and chassis intrusion pin.

GND

12C _4_ CLK #

NC

CAS EOP EN

1

12C _4_ DATA#

+5V SB

LAN 1_L INK

LED _PW R

LAN 2_L INK

LED _PW R

+5V SB

GND

GND

LOC ATORL ED1 +

LOC ATORL ED1 -

LOC ATORB TN#

LOC ATORL ED2 +

LOC ATORL ED2 -

A

B

C

D

65

A. Front panel SMBus connecting pin (6-pin FPSMB)

This header allows you to connect SMBus (System Management

Bus) equipment. It can be used for communication between

peripheral equipment in the system, which has slower
transmission rates, and power management equipment.

B. Internet status indicator (2-pin LAN1_LED, LAN2_LED)
These two 2-pin headers allow you to use the Gigabit internet

indicator cable to connect to the LAN status indicator. When this

indicator ickers, it means that the internet is properly connected.

C. Chassis intrusion pin (2-pin CHASSIS)

This header is provided for host computer chassis with chassis

intrusion detection designs. In addition, it must also work with
external detection equipment, such as a chassis intrusion
detection sensor or a microswitch. When this function is activated,
if any chassis component movement occurs, the sensor will
immediately detect it and send a signal to this header, and the
system will then record this chassis intrusion event. The default
setting is set to the CASEOPEN and GND pin; this function is off.

D. Locator LED (6-pin LOCATOR)
This header is for the locator switch and LED on the front panel.

Speaker Header

(4-pin SPEAKER1)

1

+5V

DUMMY

DUMMY

SPEAK ER

Please connect the speaker

to this header.

Front and Rear

Fan Connectors

(4-pin FRNT_FAN1)

(4-pin FRNT_FAN2)

(4-pin FRNT_FAN3)

(4-pin FRNT_FAN4)

(4-pin REAR_FAN1)

(4-pin REAR_FAN2)

Please connect the fan

cables to the fan connectors

and match the black wire to

the ground pin. All fans sup-

ports Fan Control.

GND
+12V
CPU_FAN_SP EED

FAN _SPEED_ CONTROL

FAN_ SP EED

FAN_ SP EED _CO NTR OL

+12 V

GND

CPU Fan Connectors

(4-pin CPU1_FAN)

(4-pin CPU2_FAN)

Please connect the CPU fan

cable to the connector and

match the black wire to the

ground pin.

GND
+12V
CPU_FAN_SP EED

FAN _SPEED_ CONTROL

66

Though this motherboard provides a 4-Pin CPU fan (Quiet Fan)

connector, 3-Pin CPU fans can still work successfully even with-

out the fan speed control function. If you plan to connect a 3-Pin

CPU fan to the CPU fan connector on this motherboard, please

connect it to Pin 1-3.

3-Pin Fan Installation

Pin 1-3 Connected

ATX Power Connector

(24-pin ATXPWR1)

12 1

24 13

Please connect an ATX pow-

er supply to this connector.

20-Pin ATX Power Supply Installation

Though this motherboard provides a 24-pin ATX power connector,

it can still work if you adopt a traditional 20-pin ATX power supply.

To use a 20-pin ATX power supply, please plug your power supply

along Pin 1 and Pin 13.

Though this motherboard provides an 8-pin ATX 12V power con-

nector, it can still work if you adopt a traditional 4-pin ATX 12V

power supply. To use a 4-pin ATX power supply, please plug your

power supply along Pin 1 and Pin 5.

4-Pin ATX 12V Power Supply Installation

8 5

4 1

ATX 12V Power

Connectors

(8-pin ATX12V1)

(8-pin ATX12V_1)

Please connect an ATX 12V

power supply to this connec-

tor.

5

1

8

4

1 4

5 8

12 1

24 13

67

Thermal Sensor header

(3-pin TR1)

Intelligent Platform

Management Bus header

(4-pin IPMB_1)

This 4-pin connector is used

to provide a cabled base-

board or front panel connec-

tion for value added features

and 3rd-party add-in cards,

such as Emergency Man-

agement cards, that provide

management features using

the IPMB.

1

TR1 TR1

GND

Please connect the thermal

sensor cable to either pin

1-2 or pin 2-3 and the other

end to the device which you

wish to monitor its tempera-

ture.

No connec t

GND

IPMB_SC L

IPMB_SD A

Serial port Header

(9-pin COM2)

This COM2 header supports

a serial port module.

PSU SMBus

(5-pin PSU_SMB1)

PSU SMBus monitors the

status of the power supply,

fan and system temperature.

+3VSB

1

ALERT

SMBCL K

GND

SMBDATA

Non Maskable Interrupt

Button Header

(2-pin NMI_BTN1)

Please connect a NMI de-

vice to this header.

1

CONTR OL

GND

68

Serial General Purpose

Input/Output Header

(7-pin SATA_SGPIO1)

Front Lan LED

Connector

(4-pin FRONT_LED_LAN34)

This header supports Serial

Link interface for onboard

SATA connections.

This 4-pin connector is used

for the front

LAN status

indicator.

1

SDATAOUT

SLOAD

SCLOCK

GND

GND

1

LAN3_ LIN K

LAN3_ ACT

LAN4_ ACT

LAN4_ LIN K

BMC SMB Header

(5-pin BMC_SMB_1)

(5-pin BMC_SMB_3)

This header is used for the

SM BUS devices

.

1

69

2.9 Driver Installation Guide

To install the drivers to your system, please insert the support CD to your

optical drive rst. Then, the drivers compatible to your system can be auto-

detected and listed on the support CD driver page. Please follow the order

from top to bottom to install those required drivers. Therefore, the drivers

you install can work properly.

70

Chapter 3: UEFI SETUP UTILITY

3.1 Introduction

This section explains how to use the UEFI SETUP UTILITY to congure

your system. The UEFI chip on the motherboard stores the UEFI SETUP

UTILITY. You may run the UEFI SETUP UTILITY when you start up the

computer. Please press <F2> or <Del> during the Power-On-Self-Test

(POST) to enter the UEFI SETUP UTILITY, otherawise, POST will continue

with its test routines.

If you wish to enter the UEFI SETUP UTILITY after POST, restart the sys-

tem by pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button

on the system chassis. You may also restart by turning the system off and

then back on.

Because the UEFI software is constantly being updated, the

following UEFI setup screens and descriptions are for reference

purpose only, and they may not exactly match what you see on

your screen.

3.1.1 UEFI Menu Bar

The top of the screen has a menu bar with the following selections:

Main For setting system time/date information

Advanced For advanced system congurations

H/W Monitor Displays current hardware status

Boot For conguring boot settings and boot priority

Security For security settings

Save & Exit Exit the current screen or the UEFI Setup Utility

Server Mgmt For managing the server

Event Logs For event log conguration

71

3.1.2 Navigation Keys

Use < > key or < > key to choose among the selections on

the menu bar, and use < > key or < > key to move the cursor

up or down to select items, then press <Enter> to get into the sub

screen. You can also use the mouse to click your required item.

Please check the following table for the descriptions of each navigation

key.

Navigation Key(s) Function Description

+ / - To change option for the selected items

<Tab> Switch to next function
<PGUP> Go to the previous page
<PGDN> Go to the next page
<HOME> Go to the top of the screen

<END> Go to the bottom of the screen

<F1> To display the General Help Screen
<F7> Discard changes and exit the SETUP UTILITY

<F9> Load optimal default values for all the settings
<F10> Save changes and exit the SETUP UTILITY
<F12> Print screen

<ESC> Jump to the Exit Screen or exit the current screen

72

3.2 Main Screen

When you enter the UEFI SETUP UTILITY, the Main screen will appear

and display the system overview.

73

3.3 Advanced Screen

In this section, you may set the congurations for the following items: ACPI

Conguration, Intel(LT-SX) TXT Conguration, WHEA Conguration, CPU

Configuration, North Bridge Configuration, South Bridge Configuration,

USB Conguration, ME Subsystem, Clock Generator Conguration, Stor-

age Conguration,Super IO Conguration, Serial Port Console Redirection

and Voltage Control.

Setting wrong values in this section may cause the system to

malfunction.

Instant Flash

Instant Flash is a UEFI ash utility embedded in Flash ROM. This

convenient UEFI update tool allows you to update system UEFI

without entering operating systems first like MS-DOS or Win-

dows®. Just save the new UEFI le to your USB ash drive, op-

py disk or hard drive and launch this tool, then you can update

your UEFI only in a few clicks without preparing an additional

oppy diskette or other complicated ash utility. Please be noted

that the USB ash drive or hard drive must use FAT32/16/12 le

system. If you execute Instant Flash utility, the utility will show

the UEFI les and their respective information. Select the proper

UEFI le to update your UEFI, and reboot your system after the

UEFI update process is completed.

74

3.3.1 ACPI Conguration

Suspend Mode

Use this item to enable or disable the highest ACPI Sleep state

(S1). If enabled, the system enters S1 level when the SUSPEND

button is pressed.

ACPI HPET Table

Use this item to enable or disable ACPI HPET Table. The default

value is [Enabled].

PCI Devices Power On

Use this item to enable or disable PCI devices to turn on the sys-

tem from the power-soft-off mode.

RTC Alarm Power On

Use this item to enable or disable RTC (Real Time Clock) to pow-

er on the system.

Ring-In Power On

Use this item to enable or disable Ring-In signals to turn on the

system from the power-soft-off mode.

75

3.3.2 Intel(LT-SX) TXT Conguration

76

3.3.3 WHEA Conguration

WHEA Support

Use this option to enable or disable Windows Hardware Error

Architecture. The default value is [Enabled].

77

3.3.4 CPU Conguration

CPU_BSP1 Information

Display information regarding the primary processor (BootStrap

Processor).

CPU_AP1 Information

Display information regarding the non-primary processor (Applica-

tion Processors).

Intel Hyper Threading Technology

To enable this feature, a computer system with an Intel processor

that supports Hyper-Threading technology and an operating sys-

tem that includes optimization for this technology is required. This

option will be hidden if the installed CPU does not support Hyper-

Threading technology.

Active Processor Cores

Use this item to select the number of cores to enable in each pro-

cessor package. The default value is [All].

Limit CPUID Maximum

This function allows you to limit CPUID maximum value. Unless

the OS is Windows® NT, disable this function.

78

No-Execute Memory Protection

No-Execution (NX) Memory Protection Technology is an enhance-

ment to the IA-32 Intel Architecture. An IA-32 processor with “No

Execute (NX) Memory Protection” can prevent data pages from

being used by malicious software to execute codes. This option

will be hidden if the current CPU does not support No-Excute

Memory Protection.

Hardware Prefetcher

Use this turn on/off the MLC streamer prefetcher.

Adjacent Cache Line Prefetch

Use this to turn on/off prefetching of adjacent cache lines.

DCU Streamer Prefetcher

If enabled, the DCU (data cache unit) Streamer Prefetcher

prefetches the next L1 Data line based upon multiple loads in

same cache line. It is recommended to enable this option to en-

hance data processing capacity.

DCU IP Prefetcher

If enabled, the DCU (data cache unit) IP (Instruction Pointer)

Prefetcher predict what memory addresses are going to be used

by the program and deliver that data just in time.

Intel Virtualization Technology

When this option is set to [Enabled], a VMM (Virtual Machine

Architecture) can utilize the additional hardware capabilities pro-

vided by Vanderpool Technology. This option will be hidden if the

installed CPU does not support Intel Virtualization Technology.

CPU Power Management

Use this to congure CPU Power Management.

79

3.3.5 North Bridge Conguration

IOH ( I/O hub) Conguration

Intel® VT-d

Use this to enable/disable Intel® Virtualization Technology for the

Directed I/O.

Intel® I/OAT

Use this to enable/disable Intel® I/O AccelearationTechnology.

Primary Graphics Adapter

This allows you to select a graphics device as the primary display.

The default value is [PCI Express].

Onboard VGA

Enable or disable the onboard VGA.

Onboard LAN1 & LAN2

This allows you to enable or disable onboard LAN1 & LAN2.

Onboard LAN1 & LAN2 Link Speed

This allows you to select LAN1 & LAN2 Link Speed.

Onboard LAN3 & LAN4

This allows you to enable or disable onboard LAN3 & LAN4.

Onboard LAN3 & LAN4 Link Speed

This allows you to select LAN3 & LAN4 Link Speed.

LSI 2308 Link Speed

This allows you to select LSI 2308 Link Speed.

PCIE6 Link Speed

This allows you to select PCIE6 Link Speed.

80

PCIE7 Link Speed

This allows you to select PCIE7 Link Speed.

QPI ( Intel Quickpath Interconnect) Conguration

Isoc

Use this to enable/disable Isoc. It is recommended to select [En

abled].

QPI Link Speed Mode

This allows you to select QPI Link Speed Mode. It is recommend-

ed to select [Auto].

QPI Link Frequency Select

This allows you to select QPI Link Frequency.

Memory Conguration

Memory Mode

Select the mode for memory initialization.

[Independent]:

Independent channel mode.

[Mirroring]:

The memory subsystem writes identical data to two

channels simultaneously. Identical memory modules should be

installed in the two channels closest to the processor.

[Lock Step]:

The two channels closest to the processor are com

bined to form a single channel. Memory modules must be iden

tical in size, speed, and technology in corresponding slots.

[Sparing]:

This mode occurs when on-demand inactive memory is auto

matically activated by the system to temporarily replace failed

memory until a service action can be performed.

DRAM RAPL BWLIMIT

This item sets the limits on the average power consumption and

the bandwidth of a DRAM module.The options are Disabled, 0,

1(Intel recommended value), 8 and 16.

Perform and DFX devices

This item can set the Perfmon and DFX devices hidden or unhid

den.

81

DRAM RAPL (Running Average Power Limit ) Mode

RAPL (Running Average Power Limit ) provides mechanisms to

enforce power consumption limits on supported processors. The

default is [DRAM RAPL Mode 1].

Numa

Enable or disable the support of Non-Uniform Memory Access.

MPST Support

Enable or disable the support of Memory Power StateTable.

DRAM Frequency

If [Auto] is selected, the motherboard will detect the memory

module(s) inserted and assign the appropriate frequency auto

matically.

Channel Interleaving

It allows you to enable Channel Memory Interleaving. The default

value is [Auto].

Rank Interleaving

It allows you to select a rank memory interleaving method. The

default value is [Auto].

Patrol Scrub

Patrol Scrub is a background activity initiated by the processor to

seek out and x memory errors. The default value is [Enabled].

Demand Scrub

Fix the error when the CPU or I/O issues a demand-read com

mand, and the read data from memory turns out to be a correct

able error. The default value is [Disabled].

Data Scrambling

Enable this feature to ensure data security and integrity.

Thermal Throttling

Use this automatic memory throttling feature to reduce power

consumption. The default value is [CLTT] (Closed Loop Thermal

Throttling).

DIMM Information

Display DIMM information.

82

3.3.6 South Bridge Conguration

Restore on AC/Power Loss

This allows you to set the power state after an unexpected AC/power

loss. If [Power Off] is selected, the AC/power remains off when the

power recovers. If [Power On] is selected, the AC/power resumes

and the system starts to boot up when the power recovers.

Deep Sleep

Mobile platforms support Deep S4/S5 in DC only and desktop

platforms support Deep S4/S5 in AC only. The default value is

[Disabled].

Onboard Debug Port LED

Use this to enable or disable the Onboard Debug Port LED. The

default value is [Auto].

83

3.3.7 USB Conguration

USB 2.0 Controller

Use this item to enable or disable the use of USB 2.0 controller.

Legacy USB Support

Use this option to select legacy support for USB devices. There

are four conguration options: [Enabled], [Auto], [Disabled] and

[UEFI Setup Only]. The default value is [Enabled]. Please refer to

below descriptions for the details of these four options:

[Enabled] - Enables support for legacy USB.

[Auto] - Enables legacy support if USB devices are connected.

[Disabled] - USB devices are not allowed to use under legacy

OS and UEFI setup when [Disabled] is selected. If you have USB

compatibility issues, it is recommended to select [Disabled] to

enter OS.

[UEFI Setup Only] - USB devices are allowed to use only under

UEFI setup and Windows / Linux OS.

84

3.3.8 Intel® ME Subsystem

Intel® ME Subsystem

Display information regarding Intel® Management Engine.

85

3.3.9 Clock Generator Conguration

Spread Spectrum

It is recommended to disable this option for better system stability.

86

3.3.10 Storage Conguration

SATA Mode Selection

This item is for SATAIII_0, SATAIII_1 and SATAII_PORT_0 ports.

Use this to select SATA mode. Conguration options: [IDE Mode],

[AHCI Mode], [RAID Mode] and [Disabled]. The default value is

[AHCI Mode].

AHCI (Advanced Host Controller Interface) supports NCQ and

other new features that will improve SATA disk performance but

IDE mode does not have these advantages.

SATA Aggressive Link Power Management

Use this item to congure Aggressive Link Power Management.

Hard Disk S.M.A.R.T.

Use this to enable or disable S.M.A.R.T. (Self-Monitoring, Analy-

sis, and Reporting Technology).

LSI 2308

This item is for LSI_SAS_0 and LSI_SAS_1 ports. Use this to en-

able or disable LSI SAS operation mode.

Bootable LSI Controller

Use this to select LSI SAS Option ROM

SCU Devices

Use this to enable or disable SCU devices.

87

Onboard SCU Oprom/Driver

Use this to enable or disable LSI SAS Option ROM. If Option

ROM is disabled, you cannot use the SATA devices connected to

the LSI SAS controller as Boot Device.

We recommend to use Intel® C602 SATA ports (SATAIII_0,

SATAIII_1 and SATAII_PORT_0) for your bootable devices. This

will minimum your boot time and get the best performance. But

if you still want to boot from the LSI SAS controller, you can

enable it from the UEFI.

88

3.3.11 Super IO Conguration

Serial Port 1 Conguration

Use this item to congure the onboard serial port 1.

Serial Port 2 Conguration

Use this item to congure the onboard serial port 2.

89

3.3.12 Serial Port Console Redirection

Console Redirection

Use this option to enable or disable Console Redirection.

Console Redirection Settings

Use this option to congure Console Redirection Settings.

90

3.3.13 Voltage Control

DRAM 1 Voltage

Use this to select DRAM 1 Voltage. The default value is [Auto].

DRAM 2 Voltage

Use this to select DRAM 2 Voltage. The default value is [Auto].

PLL 1 Voltage

Use this to select CPU PLL 1 Voltage. The default value is [Auto].

PLL 2 Voltage

Use this to select CPU PLL 2 Voltage. The default value is [Auto].

VTT 1 Voltage

Use this to select VTT 1 Voltage. The default value is [Auto].

VTT 2 Voltage

Use this to select VTT 2 Voltage. The default value is [Auto].

PCH Voltage

Use this to select PCH Voltage. The default value is [Auto].

91

3.4 Hardware Health Event Monitoring Screen

In this section, it allows you to monitor the status of the hardware on your

system, including the parameters of the CPU temperature, motherboard

temperature and the critical voltage.

CPU1_FAN Setting

This allows you to set the speed of CPU1_FAN. The default value

is [Full On].

CPU2_FAN Setting

This allows you to set the speed of CPU2_FAN. The default value

is [Full On].

REAR_FAN1 Setting

This allows you to set the speed of REAR_FAN1. The default

value is [Full On].

REAR_FAN2 Setting

This allows you to set the speed of REAR_FAN2. The default

value is [Full On].

FRNT_FAN1 Setting

This allows you to set the speed of FRNT_FAN1. The default

value is [Full On].

FRNT_FAN2 Setting

This allows you to set the speed of FRNT_FAN2. The default

value is [Full On].

FRNT_FAN3 Setting

This allows you to set the speed of FRNT_FAN3. The default

value is [Full On].

92

FRNT_FAN4 Setting

This allows you to set the speed of FRNT_FAN4. The default

value is [Full On].

Watch Dog Timer

This allows you to enable or disable the Watch Dog Timer. The

default value is [Disabled].

Case Open Feature

This allows you to enable or disable the Case Open Feature. The

default value is [Enabled].

Clear Status

Enable to clear case open status if case open has been detected.

93

3.5 Server Management

System Event Log

Enter to congure System Event Logging features during boot.

BMC Network Conguration

Enter to congure BMC Network parameters.

94

3.6 Boot Screen

In this section, it will display the available devices on your system for you

to congure the boot settings and the boot priority.

Boot Option #1

Select boot option #1.

Setup Prompt Timeout

This shows the number of seconds to wait for setup activation

key. 65535(0XFFFF) means indenite waiting.

Bootup NumLock State

If this item is set to [On], it will automatically activate the Numeric

Lock function after boot-up.

Other PCI Device ROM Priority

Use this to adjust the PCI ROM Priority. The default value is [Leg

acy ROM].

Full Screen Logo

Use this item to enable or disable OEM Logo. The default value

is [Enabled].

AddOn ROM Display

Use this option to adjust AddOn ROM Display. If you enable the

option “Full Screen Logo” but you want to see the AddOn ROM

information when the system boots, please select [Enabled]. Con-

guration options: [Enabled] and [Disabled]. The default value is

[Enabled].

95

Boot From Onboard LAN

Use this item to enable or disable the Boot From Onboard LAN

feature.

Boot From PCIE LAN

Use this item to enable or disable the Boot From PCIE LAN fea-

ture.

96

3.7 Security Screen

In this section, you may set or change the supervisor/user password for

the system. For the user password, you may also clear it.

97

3.8 Exit Screen

Save Changes and Exit

When you select this option, the following message “Save con-

guration changes and exit setup?” will pop-out. Select [Yes] to

save the changes and exit the UEFI SETUP UTILITY.

Discard Changes and Exit

When you select this option, the following message “Discard

changes and exit setup?” will pop-out. Select [Yes] to exit the

UEFI SETUP UTILITY without saving any changes.

Discard Changes

When you select this option, the following message “Discard

changes?” will pop-out. Select [Yes] to discard all changes.

Load UEFI Defaults

Load UEFI default values for all the setup questions. F9 key can

be used for this operation.

98

3.9 Event Logs

Change Smbios Event Log Settings

This allows you to congure the Smbios Event Log Settings.

View Smbois Event Log

This allows you to view the Smbios Event Log.

99

Chapter 4: Software Support

4.1 Install Operating System

This motherboard supports Microsoft® Windows® Server 2003 / 2003 R2

/ 2008 / 2008 R2 / Linux compliant. Because motherboard settings and

hardware options vary, use the setup procedures in this chapter for general

reference only. Refer your OS documentation for more information.

4.2 Support CD Information

The Support CD that came with the motherboard contains necessary driv-

ers and useful utilities that enhance the motherboard’s features.

4.2.1 Running The Support CD

To begin using the support CD, insert the CD into your CD-ROM

drive. The CD automatically displays the Main Menu if “AUTORUN”

is enabled in your computer. If the Main Menu does not appear auto-

matically, locate and double click on the le “ASRSETUP.EXE” in the

Support CD to display the menu.

4.2.2 Drivers Menu

The Drivers Menu shows the available device’s drivers if the system

detects installed devices. Please install the necessary drivers to acti-

vate the devices.

4.2.3 Utilities Menu

The Utilities Menu shows the application softwares that the mother-

board supports. Click on a specic item then follow the installation

wizard to install it.

4.2.4 Contact Information

If you need to contact ASRock or want to know more about ASRock,

you’re welcome to visit ASRock’s website at http://www.asrock.com;

or you may contact your dealer for further information.

100

Chapter 5: Troubleshooting

5.1 Troubleshooting Procedures

Follow the procedures below to troubleshoot your system.

Always unplug the power cord before adding, removing or changing

any hardware components. Failure to do so may cause physical

injuries to you and damages to motherboard components.

1. Disconnect the power cable and check whether the PWR LED is off.

2. Unplug all cables, connectors and remove all add-on cards from the

motherboard. Make sure that the jumpers are set to default settings.

3. Conrm that there are no short circuits between the motherboard

and the chassis.

4. Install a CPU and fan on the motherboard, then connect the chassis

speaker and power LED.

If there is no power...

1. Conrm that there are no short circuits between the motherboard

and the chassis.

2. Make sure that the jumpers are set to default settings.

3. Check the settings of the 115V/230V switch on the power supply.

4. Verify if the battery on the motherboard provides ~3VDC. Install a

new battery if it does not.

If there is no video...

1. Try replugging the monitor cables and power cord.

2. Check for memory errors.

If there are memory errors...

1. Verify that the DIMM modules are properly seated in the slots.

2. Use recommended DDR3 1600/1333/1066 ECC DIMMs.

3. If you have installed more than one DIMM modules, they should be

identical with the same brand, speed, size and chip-type.

4. Try inserting different DIMM modules into different slots to identify