Page 1
ASKO
IMPORTANT!
Read all of these instructions
before installing the dishwasher .
XL TALL TANK
DISHWASHER
INSTALLATION
INSTRUCTIONS
AA
UTUT
OMAOMA
A
UT
OMA
AA
UTUT
OMAOMA
TT
he drhe dr
T
he dr
TT
he drhe dr
ofof
the mac the mac
of
the mac
ofof
the mac the mac
eliminate potential drain problems,eliminate potential drain problems,
eliminate potential drain problems,
eliminate potential drain problems,eliminate potential drain problems,
e this hose in placee this hose in place
lealea
vv
e this hose in place
lea
v
e this hose in place
lealea
vv
e this hose in place
CONTENTSCONTENTS
CONTENTS
CONTENTSCONTENTS
Introduction 2
What You Need 2
Dimensions 3
Preparing the Location 3
Water Supply 4
Drain Connections 5
Electrical Connections 6
Preparing the Dishwasher for Installation 6
Moving the Machine into Place 7
Connecting the Electric Cable 8
Connecting the Water Supply 8
Adjusting the Leveling Legs 9
Fastening the Dishwasher to the Cabinet 9
Installing the Toe Kick 9
Fitting the D3252XLFI, D3532XLFI, and D3532XLFIWS Custom Door
Panel 10
Index 12
TIC HIGH LTIC HIGH L
TIC HIGH L
TIC HIGH LTIC HIGH L
ain hose is fain hose is f
ain hose is f
ain hose is fain hose is f
hine ahine a
hine a
hine ahine a
t the best height.t the best height.
t the best height.
t the best height.t the best height.
OOPOOP
OOP
OOPOOP
astened to the bacastened to the bac
astened to the bac
astened to the bacastened to the bac
TT
oo
T
o
TT
oo
..
.
..
kk
k
kk
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
Page 1
Page 2
INTRODUCTIONINTRODUCTION
INTRODUCTION
INTRODUCTIONINTRODUCTION
Read these instructions carefully and completely before
you install the machine. The installation should be
carried out by a qualified person who is familiar with all
local codes and ordinances for electrical and plumbing
connections.
If a dishwasher is being installed in this area for the
first time, most of the cabinet work, plumbing, and
electrical has to be done before you move the machine
into place.
WHAWHA
WHA
WHAWHA
TOOLSTOOLS
TOOLS
TOOLSTOOLS
1) Phillips No. 2 screwdriver
2) Flat blade screwdriver
3) Torx screwdriver size T 20
4) Adjustable wrenches (if you use copper fittings)
5) Open-ended wrench (1/2" [12 mm] or 5/8" [16 mm])
6) Tape measure
7) Spirit level
8) Electric drill with 1” drill bit
9) Keyhole saw
T T
YY
OU NEEDOU NEED
T
Y
OU NEED
T T
YY
OU NEEDOU NEED
If you are replacing an old dishwasher, you must check
the plumbing connection and wiring before you move
the new dishwasher into place.
NOTE: Cosmetic damage must be reported to the
ASKO dealer within five days from the date of purchase.
As soon as you unpack the dishwasher, thoroughly
check it for cosmetic damage.
MAMA
TERIALSTERIALS
MA
TERIALS
MAMA
TERIALSTERIALS
♦ Minimum 3/8" OD copper tubing of sufficient length
for your installation
♦ Shut-off valve and fittings for water supply line
Tip Guards (optional)Tip Guards (optional)
Tip Guards (optional)
Tip Guards (optional)Tip Guards (optional)
When it is not possible to attach the
dishwasher to the cabinet or the
underside of the cabinet top, you
should install tip guards to prevent the
machine from tipping when you open
the door.
Refer to page 4 for installation
instructions.
TECHNICAL DTECHNICAL D
TECHNICAL D
TECHNICAL DTECHNICAL D
Water pressure 18-176 psi
Power 120 V, 60 Hz, 15 amp.
Heating element 1200 W
Max loading 1300 W
AA
A
AA
TT
T
TT
AA
A
AA
Tip Guards
(P/N 8070851)
The dishwasher is shipped with the high loop drain
hose, inlet hose and electrical cord attached and ready
to be connected.
Page 2
Page 3
DIMENSIONSDIMENSIONS
DIMENSIONS
DIMENSIONSDIMENSIONS
UNIT DIMENSIONSUNIT DIMENSIONS
UNIT DIMENSIONS
UNIT DIMENSIONSUNIT DIMENSIONS
US Metric
Measurements Measurements
Height 34" - 37" 864 - 939 mm
Width 24" 610 mm
Depth 23-5/8" 600 mm
Depth w/door open 48” 1219 mm
Weight 104 lb 48 kg
48"
1219 mm
24"
610 mm
34" - 37"
864 - 939 mm
23-5/8"
600 mm
Door
6-1/4" - 8-1/4"
159 - 210 mm
1½”
38 mm
PREPPREP
PREP
PREPPREP
The best place for your dishwasher is in the kitchen
near the sink. This makes it easier to connect the water
and drain supply lines.
A built-in dishwasher must be enclosed on the top, both
sides and the back.
The electrical and water supplies should enter through
the area indicated by the shading on the illustration at
right.
Access holes must be round and smooth, and they
should be 1-1/2” (38mm) in diameter.
EUREUR
EUR
EUREUR
The kick plate supplied with your dishwasher fits a 24"
(610 mm) opening. When using European standard
installation, a 23-1/2” (597 mm) wide toe kick is available
from your ASKO dealer . (Part numbers: White=80735660, Black=8073566-29, Metallic=8073566-81,
Bisque=8059758-84)
ARING ARING
ARING
ARING ARING
OPEAN INSTOPEAN INST
OPEAN INST
OPEAN INSTOPEAN INST
THE LTHE L
THE L
THE LTHE L
ALLAALLA
ALLA
ALLAALLA
OCAOCA
OCA
OCAOCA
TIONSTIONS
TIONS
TIONSTIONS
TIONTION
TION
TIONTION
6-1/4"
159 mm
CABINET OPENINGCABINET OPENING
CABINET OPENING
CABINET OPENINGCABINET OPENING
US Metric
Measurements Measurements
Height 34" - 37" 864 - 939 mm
Width 24-1/8” 613 mm
Depth 23-5/8" 600 mm
1½”
38 mm
6-1/4" to 8-1/4"
159 to 210 mm
34" - 37"
2-1/4"
57 mm
860 - 920 mm
23-7/16"
596 mm
24-1/8"
613 mm
Page 3
Page 4
CORNER INSTCORNER INST
CORNER INST
CORNER INSTCORNER INST
If the dishwasher is installed in a corner, there must be
a minimum clearance of 2” (50 mm) from the side wall
so the door can open.
ALLAALLA
ALLA
ALLAALLA
TIONTION
TION
TIONTION
INSTINST
INST
INSTINST
(OPTIONAL)(OPTIONAL)
(OPTIONAL)
(OPTIONAL)(OPTIONAL)
When it is not possible to fasten the dishwasher to the
cabinet, you should install tip guards to prevent the
machine from tipping when the door is opened. The tip
guards can be attached either to the floor or the wall.
The tip guards should be mounted behind the machine,
19” (483 mm) apart (measuring center to center) and
18-1/2” (470 mm) from the front of the machine. (Note:
This measurement could vary, depending on the
thickness of the custom panel, if any.)
ALLING ALLING
ALLING
ALLING ALLING
THE THE
THE
THE THE
TIP GUTIP GU
TIP GU
TIP GUTIP GU
ARDSARDS
ARDS
ARDSARDS
2” clearance
WW
AA
TER SUPPLTER SUPPL
W
A
TER SUPPL
WW
AA
TER SUPPLTER SUPPL
WARNING! Plumbing connections must comply with
applicable sanitary , safety and plumbing codes in your
area.
The machine can be connected to either a hot or cold
water supply. If a cold water supply is used, the washing
times will be longer but the performance will not be
affected.
The dishwasher comes with a 6-foot PEX water supply
line that has a 3/8" NPT female connection.
EE
E
EE
PEX tubing with 3/8”
compression fitting
PEX tubing has a 95-year
spec life. Fits American
dishwasher water supply
valves.
ASYASY
ASY
ASYASY
II
NSTNST
NST
I
NSTNST
II
ALLALL
ALL
ALLALL
YY
Y
YY
CONNECTIONS CONNECTIONS
CONNECTIONS
CONNECTIONS CONNECTIONS
Rear
We recommend that you install tip
guards when it isn’t possible to fasten
the dishwasher to the cabinet.
After determining where the water supply line will enter
under the sink, drill a 1-1/2" (38 mm ) access hole and
run the line to the approximate inlet valve location shown
in the figure below. The water line inlet valve is on the
right rear of the machine.
For service convenience, a shut-off valve (not supplied)
should be installed in the supply line in an easily
accessible location, such as, beneath the sink.
It is important that the water supply line and the shut-off
valve have a sufficient flow volume. At last 3 gallons (12
liters) per minute must be able to pass through the
line. The water pressure should be 18-176 psi.
WARNING!
In order to prevent heat damage to the inlet valve, all
solder connections must be made before the water
line is connected to the dishwasher.
Tip Guards
(P/N 8070851)
Drain hose boot
Ready to be cut to desired
drain connection. Only
one clamp required.
Electrical cord
1 10-120 volt s, 15/20 amp
cord supplied with unit.
WARNING!
Do not use an extension cord for this appliance.
Page 4
NOTE:
(1) Water supply
(2) Water supply valve
(not supplied)
Be sure to run the PEX tubing through the hole
to sink compartment before moving the
dishwasher into position.
Page 5
DRAIN CONNECTIONSDRAIN CONNECTIONS
DRAIN CONNECTIONS
DRAIN CONNECTIONSDRAIN CONNECTIONS
ASKO provides a 7/8” (22 mm) corregated drain hose
which is connected to the back of the unit to form a high
loop. If additional drain hose is the added hose and
any joints or connections can be no smaller than 7/8"
O.D. Stock.
NOTE:Do not use any fittings anywhere in the drain
line that are less than 7/8" (22 mm) O.D. Stock.
.
The access hole for the drain line should be 1-1/2" (38 mm).
The end of the drain line is
1/2” (12 mm), but it is
adjustable to 7/8”, 3/4”, 5/
8” (22mm, 19 mm, and 16
mm). If the drain connection is larger than 1/2” (12 mm),
you can easily cut the drain line to fit the connection.
The illustrations to the right show three ways to connect
the drain supply line.
THE HIGH LOOPTHE HIGH LOOP
THE HIGH LOOP
THE HIGH LOOPTHE HIGH LOOP
The high loop is necessary for proper
draining. Therefore, all ASKO
dishwashers have the drain hoses
attached to the drain pump and
fastened to the top back of the unit, as illustrated. This
gives the drain hose an automatic high loop, which is
necessary for proper draining. The drain hose is
fastened at the best high loop height.
To eliminate potential drain problems, simply leave
this hose in place.
THREE THREE
THREE
THREE THREE
DRAIN CONNECTIONSDRAIN CONNECTIONS
DRAIN CONNECTIONS
DRAIN CONNECTIONSDRAIN CONNECTIONS
A.)T ypical connection to sink plumbing before
trap (high loop drain)
B.)Connection to air gap then to the trap
WW
W
WW
AA
A
AA
YY
Y
YY
S S
S
S S
TT
T
TT
O INSTO INST
O INST
O INSTO INST
508
508
ALLALL
ALL
ALLALL
IMPORIMPOR
IMPOR
IMPORIMPOR
REMEMBER:REMEMBER:
REMEMBER:
REMEMBER:REMEMBER:
♦ Failure to provide the proper drain connection height
(minimum of 20" (508 mm) above the bottom of the
dishwasher base) or a 20" (508 mm) high loop will
result in improper drainage, which will damage the
machine.
♦ No part of the drain hose should be higher than 35"
(889 mm) from the bottom of the dishwasher.
♦ The drain hose can be extended to a maximum length
of 10 feet (3048 mm). Joints and jointed tubes, if any,
must have a minimum 7/8" (22 mm) O.D. Stock.
♦ If the drain line is going to be connected to a waste
disposer, be sure to remove the knockout or plug
from the fitting on the disposer before connecting
the drain line.
♦ Do not use fittings smaller than 7/8” (22 mm);
otherwise the water may not drain properly.
When the installation is ready, open the supply valve
and let the pressure act for a while. Then check that all
connections are tight and there are no leaks.
TT
ANT ANT
T
ANT
TT
ANT ANT
THINGS THINGS
THINGS
THINGS THINGS
TT
T
TT
OO
O
OO
C.)Connection to waste disposer with air gap
508
NOTE: Don’t forget to remove the knockout
or plug from the disposer fitting.
Page 5
Page 6
ELECTRICAL CONNECTIONSELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONSELECTRICAL CONNECTIONS
WARNING!
electrical appliance, be sure the electrical power
has been turned off at the breaker/fuse box.
WARNING!
supply and place a tag at the disconnect switch
indicating that you are working on the circuit.
WARNING!
connections must comply with the applicable
portions of the national electrical code and/or
other local electrical codes.
The dishwasher comes with an electrical
cord for 110-120 volts, 15/20 amp
supplied. This cord should be plugged into
the 110-120 volt outlet under the sink.
If the cord is not long enough, or if a hardwire installation is needed, follow
instructions on page 8.
GRGR
OUNDING INSTROUNDING INSTR
GR
OUNDING INSTR
GRGR
OUNDING INSTROUNDING INSTR
This unit must be grounded to operate properly. It must
be connected to a grounded metal, permanent wiring
system, or an equipment-grounding conductor must
be run with the circuit conductors and connected to the
equipment-grounding terminal or lead of the appliance.
Before working on wiring for any
Disconnect electrical power
Electrical and grounding
UCTIONSUCTIONS
UCTIONS
UCTIONSUCTIONS
WARNING!
Do not use an extension cord for this appliance.
NOTE: Access holes should be 1-1/2” to 2” (38 mm
to 50 mm) in diameter with no sharp edges.
Damage to the dishwasher could occur if it is not
properly grounded.
WARNING!
drain line and branch circuit wiring do not touch
any exposed terminals of dishwasher wiring.
Make sure the water supply line,
PREPPREP
PREP
PREPPREP
At this point the styrofoam, plastic wrap, and the wood
pallet (base) should be removed from the dishwasher.
Now is an excellent time to inspect for any shipping
damage. Should you find any damage, you should
report it to your dealer or builder immediately.
Be sure to remove the toe kick and toe kick insulation
which are on top of the dishwasher.
SLIDES FOR LEGSSLIDES FOR LEGS
SLIDES FOR LEGS
SLIDES FOR LEGSSLIDES FOR LEGS
The unit comes with white plastic slides for the legs to
protect the kitchen floor from being damaged when you
slide the unit into place. The slides simply snap onto
the bottom of the legs.
Protective slides for legs simply
snap onto the bottom of the legs.
ARING ARING
ARING
ARING ARING
THE DISHWTHE DISHW
THE DISHW
THE DISHWTHE DISHW
ASHER FOR INSTASHER FOR INST
ASHER FOR INST
ASHER FOR INSTASHER FOR INST
ALLAALLA
ALLA
ALLAALLA
THE FILL STRIPSTHE FILL STRIPS
THE FILL STRIPS
THE FILL STRIPSTHE FILL STRIPS
All Asko Tall Tank dishwashers come with color-coded
fill strips to finish out the installation.
(Not on all models)
TIONTION
TION
TIONTION
Fill Strip
Page 6
NOTE:
Fill Strip
If the cabinet opening is European measurement (23-1/2 inches [597 mm]), remove the fill
strips to fit the dishwasher into the opening.
Page 7
MOMO
VING VING
MO
VING
MOMO
VING VING
WARNING!
Make sure you put the protective slides on the legs to
prevent damaging the floor when you slide the unit
into place (see page 6).
1. Position the machine in front of the cabinet
opening.
2. Make the height adjustment while the dishwasher
is in front of the opening.
3. Pull out the drain hose to ensure there are no sharp
bends.
4. St art to feed water and drain lines and electric cord
(if necessary) into the access hole in the cabinet.
5. Gently slide the unit into the dishwasher opening.
As you do this, feed the drain line and inlet hose
into the access hole in the side of the cabinet.
THE MATHE MA
THE MA
THE MATHE MA
CHINE INTCHINE INT
CHINE INT
CHINE INTCHINE INT
O PLAO PLA
O PLA
O PLAO PLA
As you slide the unit into place, feed the drain line and
inlet hose into the access hole in the side of the cabinet.
CECE
CE
CECE
WARNING!
Be careful of sharp edges.
Page 7
Page 8
CONNECTING THE ELECTRIC CABLECONNECTING THE ELECTRIC CABLE
CONNECTING THE ELECTRIC CABLE
CONNECTING THE ELECTRIC CABLECONNECTING THE ELECTRIC CABLE
If the cord is not long enough, or if a hard-wire
installation is needed, follow the steps below to
complete the electrical connection.
WARNING!
the power is turned off at the breaker/fuse box.
1. Connect supply cable with
a UL-listed strain relief
bushing (if nonmetallic
cable is to be used).
2. Connect branch circuit
white lead to N lead on filter .
3. Connect branch circuit
black lead to L lead on filter.
Before starting this procedure, be sure
4. Connect ground wire to ground connection screw
on the bottom.
CONNECTING CONNECTING
CONNECTING
CONNECTING CONNECTING
In order to prevent heat damage to the inlet valve, all
solder connections must be made before the water
supply line is connected.
Flush the water supply line prior to connecting it to the
water fill tube.
The unit has a float switch in the base pan to protect
against flooding. If the inlet valve connection is not
seated properly, water may leak into the base pan and
activate the float switch.
It is important that the water supply line and the shut-off
valve have a sufficient flow volume. At last 3 gallons (12
liters) per minute must be able to pass through the
line. The water pressure should be 18-176 psi.
THE THE
THE
THE THE
WW
AA
TER SUPPLTER SUPPL
W
A
TER SUPPL
WW
AA
TER SUPPLTER SUPPL
NOTE:
When doing a hard-wire installation, you must
remove the supplied power cord.
YY
Y
YY
(1) Water supply
(2) Water supply valve
(not supplied)
TESTING FOR LEAKSTESTING FOR LEAKS
TESTING FOR LEAKS
TESTING FOR LEAKSTESTING FOR LEAKS
1. Turn on the water supply and check for leaks.
2. Turn the power on at breaker/fuse box and test the
dishwasher operation by running a Rinse cycle.
(This should take about four minutes.)
3. Turn off the electrical power and check for leaks
Page 8
NOTE:
4. Make sure that no kinks have developed in the drain
If there are no leaks and the dishwasher seems to be
working properly, continue with the installation.
Be sure to run the PEX tubing through the hole
to sink compartment before moving the
dishwasher into position.
under the dishwasher and sink.
lines.
Page 9
ADJUSTING THE LEVELING LEGSADJUSTING THE LEVELING LEGS
ADJUSTING THE LEVELING LEGS
ADJUSTING THE LEVELING LEGSADJUSTING THE LEVELING LEGS
Now that all the connections are made and the machine
is in place under the cabinet, you should make the final
height adjustment.
1. You should set the
rear foot first. To do
this, use a
screwdriver to rotate
the adjusting screw
on the bottom front of
the machine. Turn the
screw clockwise to
raise the foot and
counterclockwise to lower it.
FASTENING THE DISHWASHER TO THE CABINETFASTENING THE DISHWASHER TO THE CABINET
FASTENING THE DISHWASHER TO THE CABINET
FASTENING THE DISHWASHER TO THE CABINETFASTENING THE DISHWASHER TO THE CABINET
It’s necessary to fasten the dishwasher to the cabinet
so it won’t tilt when the door is opened or if something
heavy is placed on the door. Use only screws provided
with the machine.
1. Use option A for U.S. or European standard
installations. Use option B only for European
standard installations.
2. Cover the screw heads with the
plastic plugs provided with the
machine.
3. When the machine is properly
attached, check that the feet are
tight against the floor and that the
machine is level.
Mounting
Screws
2. Using a 1/2” (12 mm) wrench, adjust the locking
nuts until the machine is
level. (The machine may
have an inclination of 1/4"
maximum without affecting
its performance.)
3. When the feet are properly adjusted, tighten the
locking nuts to the base pan.
BB
AA
NOTE:
When it is not possible to attach the dishwasher
to the cabinet, you should install tip guards.
(See “Tip Guards” on page 2.)
INSTINST
INST
INSTINST
SETTING SETTING
SETTING
SETTING SETTING
DEPTHDEPTH
DEPTH
DEPTHDEPTH
1. Press the grey catches
2. Pull out the holders as
3. Press in the catches so
4. Hang the toe kick onto the holders by inserting it
ALLING ALLING
ALLING
ALLING ALLING
THE THE
THE
THE THE
toward each other to
release the bracket.
far as required.
that they lock the
brackets in place.
into the grooves.
TT
T
TT
THE THE
THE
THE THE
OE KICKOE KICK
OE KICK
OE KICKOE KICK
TT
T
TT
OE KICKOE KICK
OE KICK
OE KICKOE KICK
Once you have the toe kick bracket in place, you can
install the toe kick, as follows:
1. Lay the insulation on the back side of the toe kick to
make sure it fits properly.
2. Peel the adhesive protection strip off the insulation
and press it firmly to the back side of the toe kick,
making sure you don’t cover any slots on the toe
kick.
3. Positioning the notches on the toe kick at the edge
of the access panel, slide the toe kick up behind
the access panel then let it slide to the floor.
4. Adjust the toe kick depth.
Page 9
Page 10
FITTING THE FITTING THE
FITTING THE
FITTING THE FITTING THE
CUSTCUST
CUST
CUSTCUST
OM DOOROM DOOR
OM DOOR
OM DOOROM DOOR
D3252XLFI, D3532XLFI AND D3532XLFIWSD3252XLFI, D3532XLFI AND D3532XLFIWS
D3252XLFI, D3532XLFI AND D3532XLFIWS
D3252XLFI, D3532XLFI AND D3532XLFIWSD3252XLFI, D3532XLFI AND D3532XLFIWS
P P
ANELANEL
P
ANEL
P P
ANELANEL
The D3252XLFI, D3532XLFI, and D3532XLFIWS can
only be installed with a fully-integrated custom door
panel that extends from the toe kick to the counter top.
The unit comes with everything needed to make
installing the door panel easy. The door is predrilled for
the panel’s mounting screws.
CUSTCUST
CUST
CUSTCUST
Width: 23-1/2” (597 mm)
Height: 30 1/8" (765 mm)
Thickness: 3/4” (19 mm) max
Weight: Up to 22 lb.
Fit the handle onto the panel according to the manufacturer’s instructions.
(NOTE: A handle should be used rather than a knob, because a knob
does not provide enough grip.)
NOTE: Before fitting the custom panel, the dishwasher must be installed
underneath the cabinet. After you’ve made the required measurements,
pull the machine out again to install the panel.
NOTE: Specifications subject to change without notice.
OM POM P
OM P
OM POM P
ANEL DIMENSIONSANEL DIMENSIONS
ANEL DIMENSIONS
ANEL DIMENSIONSANEL DIMENSIONS
(Measured from the top of the panel to the lower edge of
the kitchen cabinet.)
ITEMS PRITEMS PR
ITEMS PR
ITEMS PRITEMS PR
UNITUNIT
UNIT
UNITUNIT
♦ Two 3/8” screws
♦ Four 1-3/4” screws
OO
VIDED VIDED
O
VIDED
OO
VIDED VIDED
"
30 1/8
765 mm
WITH WITH
WITH
WITH WITH
THETHE
THE
THETHE
PREPPREP
PREP
PREPPREP
1. Lay the template edge-to-edge with the lower edge of the dishwasher
2. Using a pen or screw, punch holes in the template where the
3. Lay the template on the back of the wood panel, edge-to-edge with
4. Mark the location of the hole on the panel.
5. Turn the template over and lay it on the right side of the wood panel
6. Screw the short screws into the markings on the wood panel, letting
.
ARING ARING
ARING
ARING ARING
door or the adjusting frame. The broken line on the template must
pass through the center of the keyholes on the door.
keyholes are.
the rear of the lower edge and the left edge of the panel.
and mark the location of the second hole.
them project by about 1/16".
THE THE
THE
THE THE
WW
OOD POOD P
W
OOD P
WW
OOD POOD P
ANEL FOR MOUNTINGANEL FOR MOUNTING
ANEL FOR MOUNTING
ANEL FOR MOUNTINGANEL FOR MOUNTING
Page 10
Page 11
MOUNTING MOUNTING
MOUNTING
MOUNTING MOUNTING
1. Locate the screw heads in the keyholes and push the wood panel to
one side and align with the door. (Figure 5)
2. Clamp the wood panel to the dishwasher door to keep it securely in
place.
3. Open the dishwasher door and screw the wood panel into position
with the four long screws, two on either side. (Figure 6)
.
ADJUSTING THE DOOR SPRINGSADJUSTING THE DOOR SPRINGS
ADJUSTING THE DOOR SPRINGS
ADJUSTING THE DOOR SPRINGSADJUSTING THE DOOR SPRINGS
After you install the custom panel,
make sure the door stays in place at
any angle. If it tends to fall down, pull
out the machine and tension the door
springs on the sides of the machine
by moving them one hole farther back
or by twisting the spring to make it
shorter. If that doesn’t resolve the
problem, you may need to purchase
the heavy-duty door springs (part
number 8076163-77).
THE THE
THE
THE THE
WW
OOD POOD P
W
OOD P
WW
OOD POOD P
ANELANEL
ANEL
ANELANEL
D3252XLFI,D3252XLFI,
D3252XLFI,
D3252XLFI,D3252XLFI,
INSTINST
INST
INSTINST
4-inc4-inc
4-inc
4-inc4-inc
Custom panel extends to cabinet top
One installation option for a 4” toe kick is to extend the
custom panel to the cabinet top (as illustrated below).
One-Piece CustomOne-Piece Custom
One-Piece Custom
One-Piece CustomOne-Piece Custom
Door PanelDoor Panel
Door Panel
Door PanelDoor Panel
A one-piece custom door panel
with a curved handle is now
available for the FI dishwashers.
This door is available in stainless
steel (as shown), black, and white.
To order this door panel, contact
your dealer.
These doors are designed for 4” toe
kick installations.
ALLAALLA
ALLA
ALLAALLA
h h
TT
h
T
h h
TT
Panel extends from toe kick to cabinet top
D3532XLFI, D3532XLFI,
D3532XLFI,
D3532XLFI, D3532XLFI,
TION OPTIONSTION OPTIONS
TION OPTIONS
TION OPTIONSTION OPTIONS
oe Kicoe Kic
oe Kic
oe Kicoe Kic
k Installak Installa
k Installa
k Installak Installa
23-1/2"
597 mm
4-inch toe kick
30 1/8"
AND D3532XLFIWS CUSTAND D3532XLFIWS CUST
AND D3532XLFIWS CUST
AND D3532XLFIWS CUSTAND D3532XLFIWS CUST
tionstions
tions
tionstions
765 mm
OM POM P
OM P
OM POM P
6-inc6-inc
6-inc
6-inc6-inc
XL units are not designed to accomodate a 6 inch
toe kick installation. If you need a 6 inch toe kick
installation, you should install an Asko st andard
tank dishwasher model D3122 or D3252FI.
h h
h
h h
TT
T
TT
oe Kicoe Kic
oe Kic
oe Kicoe Kic
k Installak Installa
k Installa
k Installak Installa
ANELANEL
ANEL
ANELANEL
tionstions
tions
tionstions
Page 11
Page 12
INDEXINDEX
INDEX
INDEXINDEX
AA
A
AA
Access holes 3
CC
C
CC
Cabinet, fastening unit to 9
Cabinet opening dimensions 3
Connecting to water supply 9
Corner installation 4
Cosmetic damage 2
DD
D
DD
Dimensions, unit 3
Door panels, fully-integrated 11
Door springs, adjusting 10
Drain connections 4
EE
E
EE
Electrical cable connection 8
Electrical connections 7
European installations 3
FF
F
FF
Fastening unit to cabinet 9
Fill strips 6
Fully-integrated door panels 1 0
GG
G
GG
Grounding instructions 6
HH
H
HH
Heating element 2
High loop 5
Hot water supply 4
LL
L
LL
Leaks, testing for 8
Leveling legs, adjusting 9
MM
M
MM
Materials 2
Moving unit into place 7
PP
P
PP
Panels, fully-integrated 11
Placing the unit 7
Power 2
SS
S
SS
Slides for rear legs 6
TT
T
TT
Technical data 2
Tip guards 2
installing 4
Toe kick
installation options on FI units 11
installing 9
Tools 2
UU
U
UU
Unit dimensions 3
WW
W
WW
Water connection 9
Water flow volume 4
Water pressure 2
Page 12
Art. No 8075801 rev 03
Loading...