Health & Safety, Use & Care and Installation Guides
www.aristonchannel.com
SAFETY INSTRUCTIONS
IMPORTANT TO BE READ AND OBSERVED
These instructions are valid if the country
symbol appears on the appliance. If the symbol
does not appear on the appliance, please refer
to the technical instructions which will provide
the necessary instructions concerning
modication of the appliance to the conditions
of use of the country.
CAUTION : Use of the gas cooking appliance
results in the production of heat, moisture and
products of combustion in the room in which it
is installed. Ensure that the kitchen is well
ventilated, especially when the appliance is in
use: keep natural ventilation holes open or install
a mechanical ventilation device (mechanical
extractor hood). Prolonged intensive use of the
appliance may call for additional ventilation,
such as opening a window, or more eective
ventilation, for example increasing the level of
mechanical ventilation (if possible).
Failure to follow the information in this
manual exactly may cause a re or explosion,
resulting in property damage or personal injury.
Before using the appliance, read these safety
instructions. Keep them nearby for future
reference.
These instructions and the appliance itself
provide important safety warnings, to be
observed at all times. The manufacturer declines
any liability for failure to observe these safety
instructions, for inappropriate use of the
appliance or incorrect setting of controls.
Very young children (0-3 years) should be
kept away from the appliance. Young children
(3-8 years) should be kept away from the
appliance unless continuously supervised.
Children from 8 years old and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and knowledge
can use this appliance only if they are supervised
or have been given instructions on safe use and
understand the hazards involved. Children must
not play with the appliance. Cleaning and user
maintenance must not be carried out by children
without supervision.
WARNING: The appliance and its accessible
parts become hot during use. Care should be
taken to avoid touching heating elements.
Children less than 8 years of age must be kept
away unless continuously supervised.
Never leave the appliance unattended during
food drying. If the appliance is suitable for probe
usage, only use a temperature probe
recommended for this oven - risk of re.
away from the appliance, until all the components
have cooled down completely - risk of re.
Always be vigilant when cooking foods rich in
fat, oil or when adding alcoholic beverages - risk
of re. Use oven gloves to remove pans and
accessories. At the end of cooking, open the
door with caution, allowing hot air or steam to
escape gradually before accessing the cavity risk of burns. Do not obstruct hot air vents at the
front of the oven - risk of re.
open or down position, to avoid hitting the door.
When you place the rack inside, make sure that
the stop is directed upwards and in the back of
the cavity.
The device shall not be operated for more 15 s. If
after 15s the burner has not lit, stop operating
the device and open the compartment door
and/or wait at least 1 min before attempting a
further ignition of the burner.
PERMITTED USE
operated by means of an external switching
device, such as a timer, or separate remote
controlled system.
household and similar applications such as: sta
kitchen areas in shops, oces and other working
environments; farm houses; by clients in hotels,
motels, bed & breakfast and other residential
environments.
rooms).
Do not use the appliance outdoors.
substances (e. g. gasoline or aerosol cans) inside
or near the appliance - risk of re.
INSTALLATION
by two or more persons - risk of injury. Use
protective gloves to unpack and install - risk of
cuts.
comply with local regulations.
Keep clothes or other ammable materials
Exercise caution when the oven door is in the
CAUTION: The appliance is not intended to be
This appliance is intended to be used in
No other use is permitted (e. g. heating
This appliance is not for professional use.
Do not store explosive or ammable
The appliance must be handled and installed
The electrical and gas connections must
Installation, including water supply (if any),
EN
electrical connections and repairs must be
carried out by a qualied technician. Do not
repair or replace any part of the appliance unless
specically stated in the user manual. Keep
children away from the installation site. After un
packing the appliance, make sure that it has not
been damaged during transport. In the event of
problems, contact the dealer or your nearest
After-sales Service. Once installed, packaging
waste (plastic, styrofoam parts etc.) must be
stored out of reach of children - risk of suocation.
The appliance must be disconnected from the
power supply before any installation operation
- risk of electric shock. During installation, make
sure the appliance does not damage the power
cable - risk of re or electrical shock. Only activate
the appliance when the installation has been
completed.
WARNING : Modication of the appliance and
its method of installation are essential in order to
use the appliance safely and correctly in all the
additional countries.
Use pressure regulators suitable for the gas
pressure indicated in the instructions.
The room must be equipped with an air
extraction system that expels any combustion
fumes.
The room must also allow proper air
circulation, as air is needed for combustion to
occur normally. The ow of air must not be less
than 2 m³/h per kW of installed power.
The air circulation system may take air directly
from the outside by means of a pipe with an
inner cross section of at least 100 cm²; the
opening mustnot be susceptible to blockages.
The system can also provide the air needed
for combustion indirectly, i. e. from adjacent
rooms tted with air circulation tubes as
described above. However, these rooms must
not be communal rooms, bedrooms or rooms
that may present a re hazard.
Liquid petroleum gas sinks to the oor as it is
heavier than air. Therefore, rooms containing
LPG cylinders must also be equipped with vents
to allow gas to escape in the event of a leak. This
means LPG cylinders, whether partially or
completely full, must not be installed or stored
in rooms or storage areas that are below ground
level (cellars, etc.). It is advisable to keep only the
cylinder being used in the room, positioned so
that it is not subject to heat produced by external
sources (ovens, replaces, stoves, etc.) which
could raise the temperature of the cylinder
above 50°C.
Should you nd it dicult to turn the knobs for the
burner, please contact the After-sales Service, who can
replace of the burner tap if found to be faulty.
The openings use for the ventilation and dispersion of
heat must never be covered.
Carry out all cabinet cutting works before
tting the appliance in the furniture and remove
all wood chips and sawdust.
Do not remove the appliance from its polystyrene
foam base until the time of installation.
After installation, the bottom of the appliance
must no longer be accessible - risk of burn.
Connection with rigid pipe (copper or steel):
If the gas pressure is dierent from the
recommended pressure, a suitable pressure
regulator must be tted to the inlet pipe in
accordance with the current National
Regulations. Use an appropriate cabinet to
ensure that the appliance operates properly: to
install the oven under the counter (see diagram)
or in a kitchen unit, the cabinet must have the
dimensions as the picture.
To ensure adequate ventilation, the back panel
of the cabinet must be removed. It is advisable
to install the oven so that it rests on two strips of
wood, or on a completely at surface with an
opening of at least 45 x 560 mm as the picture.
Do not install the appliance behind a
decorative door - risk of re.
If the appliance is installed under the worktop,
do not obstruct the minimum gap between the
worktop and the upper edge of the oven - risk of
burns.
GAS CONNECTION
WARNING : Prior to installation, ensure that
the local distribution conditions (type of gas and
gas pressure) and the conguration of the
appliance are compatible.
Check that the pressure of the gas supply is
consistent with the values indicated in Table 1
(“Burner and nozzle specications”).
WARNING : The conguration conditions of this
appliance are stated on the label (or data plate).
WARNING : This appliance is not connected to
a combustion products evacuation device. It
must be installed and connected in accordance
with current installation regulations. Particular
attention must be paid to the relevant
requirements regarding ventilation.
If the appliance is connected to liquid gas, the
regulation screw must be fastned as tightly as
possible.
IMPORTANT : When the gas cylinder or gas
container is installed, it must be properly settled
(vertical orientation).
WARNING : This operation must be perfomed
by a qualied technician.
Use only exible or rigid metal hose for gas
connection.
Connection with a rigid pipe (copper or steel)
Connection to the gas system must be carried
out in such a way as not to place any strain of any
kind on the appliance. There is an adjustable
L-shaped pipe tting on the appliance supply
ramp and this is tted with a seal in order to
prevent leaks. The seal must always be replaced
after rotating the pipe tting (the seal is provided
with the appliance). The gas supply pipe tting is
a threaded 1/2 gas cylindrical male attachment.
Connecting a exible jointless stainless steel
pipe to a threaded attachment. The gas supply
pipe tting is a threaded 1/2 gas cylindrical male
attachment. These pipes must be installed so
that they are never longer than 2000 mm when
fully extended. Once connection has been made,
make sure that the exible metal pipe does not
touch any moving parts and is not compressed.
Only use pipes and seals that comply with
current national regulations.
IMPORTANT : If a staineless steel hose is used,
it must be installed so as not touch any moving
part of the furniture (e.g. drawer). It must pass
thorugh an area where there are no obstructions
and where it is possible to inspect it across its
entire length.
The appliance should be connected to the
main gas supply or to a gas cylinder in compliance
with the current national regulations. Before
making the connection, make sure that the
appliance is compatible with the gas supply you
wish to use. If it is not, follow the instructions
indicated in the paragraph “Adapting to dierent
types of gas”.
After connection to the gas supply, check for
leaks with soapy water. Light up the burners and
turn the knobs from max position 1* to minimum
position 2* to check ame stability.
Connection to the gas network or the gas
cylinder may be carryout using a exible rubber
or steel hose, in accordance with current national
legislation
ADAPTING TO DIFFERENT TYPES OF GAS
(THIS OPERATION NEEDS TO BE CARRIED OUT BY
A QUALIFIED TECHNICIAN.)
In order to adapt the appliance to a type of
gas other than the type for which it was
manufactured (indicated on the rating label),
follow the dedicated steps provided after
installation drawings.
Adapting to dierent types of gas.
In order to adapt the oven to a type of gas other
than the type for which it was manufactured
(indicated on the label), follow these simple
steps:
Replacing the oven burner nozzle
1. Open the oven door fully.
2. Slide the bottom of the oven out.
3. Unscrew the burner fastening screws.
4. Remove screw (V) and then the oven burner.
5. Unscrew the oven burner nozzle using the
special socket spanner for the nozzles, or better
still a 7 mm socket spanner, and replace it with a
nozzle suited to the new type of gas (see Table 1).
6. Replace all the parts, following the steps
described above in the reverse order.
EN
Take care to replace also the bottom of the oven
in its original position.
ELECTRICAL WARNINGS
IMPORTANT: Information about current and
voltage consumption is provided on the rating
plate.
The rating plate is on the front edge of the
oven (visible when the door is open).
It must be possible to disconnect the
appliance from the power supply by unplugging
it if plug is accessible, or by a multi-pole switch
installed upstream of the socket in accordance
with the wiring rules and the appliance must be
earthed in conformity with national electrical
safety standards.
The power cable must be long enough to connect the
appliance, once tted in its housing, to the main power
supply. Do not pull the power supply cable.
Do not use extension leads, multiple sockets
or adapters. The electrical components must not
be accessible to the user after installation. Do
not use the appliance when you are wet or
barefoot. Do not operate this appliance if it has a
damaged power cable or plug, if it is not working
properly, or if it has been damaged or dropped.
If the supply cord is damaged, it must be
replaced with an identical one by the
manufacturer, its service agent or similarly
qualied persons in order to avoid a hazard - risk
of electrical shock.
If the power cable needs to be replaced,
contact an autorised service center.
CLEANING AND MAINTENANCE
WARNING: Ensure that the appliance is
switched o and disconnected from the power
supply before performing any maintenance
operation; never use steam cleaning equipment
- risk of electric shock.
Do not use harsh abrasive cleaners or metal
scrapers to clean the door glass since they can
scratch the surface, which may result in shattering
of the glass.
Make sure the appliance has cooled down
before cleaning or performing maintenance risk of burns.
WARNING: Switch o the appliance before
replacing the lamp - risk of electric shock.
To avoid damaging the electric ignition device, do not
use it when the burners are not in their housing.
Wear protective gloves for cleaning and
maintenance.
DISPOSAL OF PACKAGING MATERIALS
The packaging material is 100% recyclable and is marked with
the recycle symbol
therefore be disposed of responsibly and in full compliance with
local authority regulations governing waste disposal.
DISPOSAL OF HOUSEHOLD APPLIANCES
This appliance is manufactured with recyclable or reusable materials.
Dispose of it in accordance with local waste disposal regulations.
For further information on the treatment, recovery and recycling
of household electrical appliances, contact your local authority,
the collection service for household waste or the store where you
purchased the appliance. This appliance is marked in compliance
with European Directive 2012/19/EU, Waste Electrical and Electronic
Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help
prevent negative consequences for the environment and human
health.
The symbol
documentation indicates that it should not be treated as domestic
waste but must be taken to an appropriate collection centre for the
recycling of electrical and electronic equipment.
ENERGY SAVING TIPS
Only preheat the oven if specied in the cooking table or your recipe.
Use dark lacquered or enamelled baking trays as they absorb heat
better. Food requiring prolonged cooking will continue to cook even
once the oven is switched o.
DECLARATION OF CONFORMITY
This appliance meets Ecodesign requirements of European
Regulation 65/2014 in compliance with the European standard
EN 15181.
. The various parts of the packaging must
on the product or on the accompanying
GS3 3Y4 30 IX A - GS3 3Y4 50 IX A
Burner
Specications
Grill burner
Oven burner
G20,20 mbar
G25,25 mbar
Gas natural Gas natural LPG LPG LPG
Injector 0,92 mm 0,92 mm 0,60 mm 0,60 mm 0,55 mm
Gas ow 0,143 m³/h 0,143 m³/h 109 g/h 109 g/h 109 g/h
Power 1,50 kW 1,50 kW 1,50 kW 1,50 kW 1,50 kW
Injector 0,97 mm 0,97 mm 0,65 mm 0,65 mm 0,60 mm
Gas ow 0,171 m³/h 0,171 m³/h 131 g/h 131 g/h 131 g/h
Power 1,80 kW 1,80 kW 1,80 kW 1,80 kW 1,80 kW
G20,25 mbar
G30,28-30 mbar
G31,37 mbar
G30,37 mbar G30,50 mbar
PRODUCT DESCRIPTION
EN
1
2
3
4
CONTROL PANEL
1. Control panel
2. Shelf guides
5
6
7
8
9
(the level is indicated on
the wall of the cooking
compartment)
3. Recess for roasting spit
(if present)
4. Door
5. Upper heating element
6. Light
7. Fan element
8. Identication plate
(do not remove)
9. Burner
(not visible)
1 2 3
Thermostat selection knob
Gas oven controller
2. Minute minder 3. Electric function knob
ACCESSORIES
The number and type of accessories may vary depending
on which model is purchased. Other accessories that
are not supplied can be purchased separately from the
After‑sales Service.
WIRE SHELF
The wire shelf can be used to grill
food or as a support for pans,
cake tins and other oven-proof
cooking receptacles.
DRIP TRAY
Designed to collect fat and food
particles when it is positioned
under the grid or as a plate, such
as when cooking meat, chicken
and sh with or without vegetables. Pour a little of
drinking water into the drip tray to prevent spatters of
fat or oil and smoke.
Grill, fan and turnspit combinations
ROASTING SPIT. For grilling
poultry and roasts.
INSERTING WIRE SHELVES AND OTHER ACCESSORIES
Insert the wire shelf onto the level you require by
holding it tilted slightly upwards and resting the raised
rear side (pointing upwards) down rst. Then slide it
horizontally along the runners as far as possible. The
other accessories, such as the baking tray, are inserted
horizontally by sliding them along the runners.
REMOVE THE LATERAL SHELF GUIDES
To remove the side grilles, press down the grilles and lift
them up as shown. Then, extract the grilles from their
seats.
b
a
BEFORE USE
HEAT THE OVEN
A new oven may release odours that have been left
behind during manufacturing: this is completely normal.
Before starting to cook food, we therefore recommend
heating the oven with it empty in order to remove any
possible odours. Remove any protective cardboard
or transparent lm from the oven and remove any
DAILY USE
To ret the grilles, insert the top support, then slide
them to be tted close to the cavity and push them up
to x in their original position.
accessories from inside it. Heat the oven to the
maximum temperature for about 20 minutes. The oven
must be empty during this time. Follow the instructions
for setting the function correctly.
Please note: It is advisable to air the room after using the
appliance for the first time.
START THE GAS OVEN
Gently press the thermostat knob and turn it anticlockwise to the position: to light the burner hold
the knob pressed in for 5-10 seconds. After that, turn the
thermostat knob to the desired temperature (The
position corresponds to an oven temperature of 130° C,
the to an oven temperature of 250° C).
The thermostat knob must not be pressed and held
for more than 15 seconds.
When the oven is in operation the gas oven indicator
light switches on. To interrupt the cooking at any time,
switching the oven o, turn the thermostat knob to the
position.
If the oven fails to switch on or it switches o
accidentally, turn the thermostat knob back to the
position, open the oven door and wait at least
one minute before attempting to switch the oven
on again.
USING THE ELECTRIC GRILL
Place the food to be grilled on the turnspit or on the
wire shelf. When placing the food directly on the wire
shelf, place the drip tray with some drinking water
under the food. Turn the function knob to the grill
position to activate the grill.
While using the wire shelf, it is suggested to turn over
the food about half way through the cooking.
Please note: The grill will not operate when the oven gas
is on.
FAN
It is possible activate the fan in order to help the air
circulation into the oven. Turn the relative knob on the
icon: You will feel a “click”.
FAN + GRILL
This function activates the fan and the electric grill at
the same time. This combination is useful to roast large
joints of meat or roast and gratin vegetables.
USING THE TURNSPIT
Some ovens may be equipped with an electric motor,
spit and skewers for roasting poultry or meat. Skewer
the meat and secure it in place using the two forks. Put
turnspit rod into the drive unit (A) and the groove into
the bend (B). Turn the plastic handle (C) anticlockwise.
Slide the shelf into the oven runners ensuring that the
rod slots into hole. The turnspit shelf must always be
tted in the middle of the oven (second position from
bottom).
Place the tray to collect the cooking juices: position it on
the bottom level, adding some drinking water.
B
A
To operate the turnspit, turn the relative knob to
the icon. When the turnspit is in operation, the
electrical indicator light and the oven interior light will
be switched on. To switch o the turnspit turn back
the relative knob to the icon, then turn it to the
position. We suggest to preheat the oven for 5 minutes.
At the end of cooking take the turnspit out of the oven
only by using its handle and oven gloves.
C
EN
OVEN LIGHT
The oven light switches on every time an electric
function is selected.
It's possible to activate three combinations: Oven light
and turnspit, oven light and electric grill, oven light with
both turnspit and electric grill.
If present, the electrical indicator light on the control
panel will be switched on.
SET THE MINUTE MINDER
This option does not interrupt or activate cooking
but allows you to use the display as a timer, both
while a function is active and when the oven is off.
To activate the timer, long press the time button:
the
symbol flashes on the display (1).
Use the
and buttons to set the desired
duration: the countdown begins after a few
seconds. The display shows the time of the day and
the
remains lit, confirmating the timer has been
set (2).
At the end, long press the time button to
deactivate the alarm.
1 2
Please note: To view the countdown and change it if
necessary, press the time button 2 seconds again.
TIME OF THE DAY ADJUSTMENT
Press the button. The icon between hours
and minutes will start to flash.
Using the and buttons, you can adjust the current
time of day.
CANCELLING THE ALARM SOUND
When the countdown of the minute minder is
completed, the screen will return to displaying the
current time of the day. The
and a buzzer alarm will sound, if not stopped, 5 minutes
long. Press any button to cancel the sound.
symbol will start to ash
OPTIONS
ALARM TONE
To set the alarm tone, long press button .
To select the desired tone, press buttons
sound heard will be your adjusted one.
Press the time button to conrm.
or , the last
BRIGHTNESS
To set the brightness of display, long press button .
To select the desired level, press buttons
press the time button to conrm.
Note: After prolonged blackouts all functions
will default to their factory settings and require
reprogramming.
or , then
KEY LOCK
The key lock will be active within 30 seconds after the
last button pression. The
To deactivate it, long press the time button.
icon will appear on display.
COOKING TABLE
RECIPE FUNCTION TEMPERATURE (°C) DURATION (MIN)
Cake 170 - 180 35 - 45
Small cake 170 - 180 25 - 30
Pie 180 - 200 35 - 45
Pastry 180 - 190 20 - 25
Cookies 170 - 180 20 - 25
Apple pie 180 - 190 50 - 70
Sponge cake 20 0/150* 20 - 25
Meringues 100 50
Pizza 180 - 200 20 - 30
Lasagne 180 - 200 25 - 40
Grilled chicken** 200 - 220 25 - 35
Grilled sh** 200 - 220 25 - 35
Calf steak**
Grilled meatball**
max 15 - 20
max 20 - 25
LEVEL AND
ACCESSORIES
3
3
3
3
3
3
3
3
3
3
3
3
4
4
3
3
ACCESSORIES
*Do not preheat. First half of cooking time is recommended to be at 200 °C and the other half at 150 °C.
**Food must be turned after half of the cooking time.
Wire shelf
Baking dish or cake tin
on the wire shelf
Tra y Tray with 200 ml of water
CLEANING AND MAINTENANCE
~15°
EN
Make sure that the oven has
cooled down before carrying
out any maintenance or
cleaning.
Do not use steam cleaners.
Do not use wire wool, abrasive
scourers or abrasive/corrosive
cleaning agents, as these could
damage the surfaces of the
appliance.
EXTERIOR SURFACES
• Clean the surfaces with a damp microfibre cloth.
If they are very dirty, add a few drops of pHneutral detergent. Finish off with a dry cloth.
• Do not use corrosive or abrasive detergents. If
any of these products inadvertently comes into
contact with the surfaces of the appliance, clean
immediately with a damp microfibre cloth.
INTERIOR SURFACES
• After every use, leave the oven to cool and then
clean it, preferably while it is still warm, to remove
any deposits or stains caused by food residues. To
dry any condensation that has formed as a result
of cooking foods with a high water content, let the
oven to cool completely and then wipe it with a
cloth or sponge.
• Clean the glass in the door with a suitable liquid
detergent.
• The oven door can be removed to facilitate
cleaning.
ACCESSORIES
Soak the accessories in a washing-up liquid solution
after use, handling them with oven gloves if they
are still hot. Food residues can be removed using a
washing-up brush or a sponge.
REPLACING THE LAMP
• Disconnect the oven from the power supply.
• Unscrew the cover from the lamp, replace the bulb
and screw the cover back on the lamp.
• Reconnect the oven to the power supply.
Wear protective gloves.
The oven must be disconnected
from the mains before carrying
out any kind of maintenance
work.
REMOVING AND REFITTING THE DOOR
To remove the door, open it fully and lower the
catches until they are in the unlock position.
Set the hinge lock to the widest angle. Adjust both
hinges connecting oven door to the oven to the same
position.
Later, close the opened oven door so that it will be in
a position to contact with hinge lock.
Fake a firm hold of the door with both hands – do
not hold it by the handle. Simply remove the door by
continuing to close it while pulling it upwards at the
same time until it is released from its seating.
b
Please note: Only use 15‑25 W/220‑240 V type G9, T300°C
halogen bulbs. The bulb used in the product is specifically
designed for domestic appliances and is not suitable for
general room lighting within the home (EC Regulation
244/2009).
Light bulbs are available from our After‑Sales Service.
When using halogen bulbs, do not handle them with your
bare hands as your fingerprints could cause damage. Do
not use the oven until the lamp cover has been refitted.
a
Put the door to one side, resting it on a soft surface.
Reversely perform respectively what you did while
opening door to reinstall oven door back.
TROUBLESHOOTING
Problem Possible cause Solution
Check for the presence of mains electrical
Power cut.
Disconnection from the
mains elec tricit y.
power and whether the oven is connected to
the electricity supply.
Wait at least one minute, then try to switch
the oven on again and see if the problem
persists.
The oven will not switch on
Gas supply interrupted.
Switch‑on procedure carried
out incorrectly.
Oven does not heat
Oven does not cook well
In the event of problems, turn the adjustment knob back to the position and open the oven door.
Oven door is open.
Oven controls are not
correctly adjusted.
Oven door is opened
frequently during cooking.
Check that the gas tap upstream of the oven
is open or that the liquid gas cylinder (if used)
is not empty.
Wait at least one minute and then repeat the
steps described in the “Daily use” section.
Close the door and restart.
Read the section about the oven operations
and reset the oven.
Do not open the oven door frequently, if your
recipe doesn’t require turning. The cooking
result is influenced by the decreasing
temperature.
AFTER SALES SERVICE
Before calling the After-Sales Service:
See if you can solve the problem yourself with the help
of the suggestions given in the “Troubleshooting”.
If after the above checks the fault still occurs, get in
touch with the nearest After-sales Service.
Always specify:
• a brief description of the fault;
• the type and exact model of the oven;
• the service number (number after the word Service on
the rating plate), located on the right hand edge of the
oven cavity (visible when the oven door is open).
The service number is also indicated on the guarantee
booklet;
• your full address;
• your telephone number.
If any repairs are required, please contact an authorised
After-sales Service (to guarantee that original spare
parts will be used and repairs carried out correctly).
TECHNICAL SPECIFICATIONS
Lamp power
Thermostat
Grill heater (only electric)
Supply voltage
15 ‑ 25 W
100 ‑ 250 °C max
2000 W
220 ‑ 240 V AC 50/60 Hz
x2
EN
90°C
595
565
555
545
89° max
595
5
4
600
35
550
(min.)
560
500
30
550
(min.)
35
590
5
560
x 2
x 2
EN
Whirlpool EMEA S.p.A.
Via Carlo Pisacane n. 1
20016 Pero (Mi), Italia
400011326514
Loading...