Page 1
Lucas Mid Sleeper
Important - Please read these instructions fully before starting assembly
Dimensions
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6400 800
Issue 2 -20/03/15
424/3289
Assembly Instructions - Please keep for future reference
Length - 200cm
Width - 97.5cm
Height - 115cm
391/8711
Page 2
Important - Please read these instructions fully before starting assembly
Mattress height safety notice
Important
1) Please note the maximum mattress height is indicated on the corner post inside the opening at the
top of the ladder.
2) This is legal requirement and it is vital that the mattress does not exceed this mark.
3) Maximum thickness of the mattress is 20cm:The top of the mattress shall not come above the line
marked on the bed.
4) All assembly fixings should always be tightened properly.Take care to ensure that no fixings are
loose.
5) Recommended size of the mattress for the top bunk is 90×190cm.
6) The bunk bed should not be used if any structural part is broken or missing.
7) Warning: High beds and the upper bed of bunk beds are not suitable for children under six years
due to the risk of injury from falls.
8) Children can strangle in items such as ropes, strings, cords, harnesses and belts attached to or
hung on a bunk bed.
Warning
1) Children can become trapped between the bed and wall. To avoid risk of serious injury the distance
between the top safety barrier and the wall shall not exceed 75mm or shall be more than 230mm.
2) The bed complies with EN747-1:2012
1
Safety and Care Advice
!
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Place the product on flat and
steady surface during use.
• Keep these instructions for
future use.
• To ensure an easier assembly,
we strongly advise that all
fittings are only finger tightened
during initial assembly. Only
upon completion of the
assembly should all fixing
points be fully tightened.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Dispose of all packaging
carefully and responsibly.
Care and maintenance
• Safety: To avoid any risk of
suffocation to animals or
children dispose of the plastic
bags immediately.
• Cleaning: As with all surfaces
clean with a damp cloth and
mild detergent, do not use
bleach or abrasive products.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Page 3
Please check you have all the parts listed below
1
Components - Parts
2
Front corner post x 2 (4.5 x 115cm)
8
Ladder (80 x 35.7cm)
3
End panel x 2 (97 x 39.8cm)
4
Lower stretcher x 2 (1.9 x 88.5cm)
7
Front guard rail (95.5 x 42cm)
5
Rear guard rail (95.5 x 42cm)
10
Slats x 22 (□2 x 1 x 95cm)
6
Guard rail x 2 (97 x 42cm)
9
Slats x 2 (□2 x 1 x 95cm)
2
Rear corner post x 2 (4.5 x 115cm)
12
External bracket x 2 (4.3 x 2.3 x 12cm)
11
Internal bracket x 2 (3.7 x 1.7 x 12cm)
Smaller diameter
Page 4
Please check you have all the fittings listed below
Components - Fittings
3
If you have damaged or missing components,
call the Customer Helpline:
0345 6400 800
Note:
The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
A
B
C
M6x15mm Allen screw x 8
D E
M6x45mm Allen screw x 4
F
Curved washer-large x 8
G H
J
Nut x 14
K M
Plastic plug x 2
A
Curved washer-small x 17
Plastic washer x 8
M6x65mm Allen screw x 7
M8x65mm Allen screw x 4
M6x10mm Allen screw x 46
L
Plastic cap x 4
M6x35mm Allen screw x 2
R
M6x40mm Allen screw x 4
N
M6x25mm Allen screw x 4
P
Q
Small allen key x 2 Large allen key x 1
S
0
5
10 15 20 25 30 35 40
45
50
55
60 65 70
75
80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
0
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150
1 2 3 4 5 6
Ruler/tape
measure
Ruler - Use this ruler to help correctly identify the screws
Tools required
Foot x 2
Page 5
Assembly Instructions
4
Assembling side
frames
Lay front corner post
,rear corner post , end
panel and lower
stretcher flat on the
floor as shown.
Note:
The holes in end
panel must be at the
top.
Note:
The bottom of rear
corner post is smaller
diameter.
Insert end panel into
the large holes in posts
.
Secure using fixings
and .
Note:
Do not fully
tighten screws .
Assemble lower stretcher
in between the corner
posts using fixings and
.
Note:
Do not fully
tighten screws .
Insert end caps into
the top of the corner
posts.
Repeat for the other side
frame.
1
3
4
3
3
2
A
C
A
4
B
C
B
D
Note: Hole at top
A
C
D
C
B
2
4
Top
Bottom
A
C
C
B
2
1
3
4
D
3
2
2
Step 1
2
Smaller end
Rear
Front
Page 6
Step 2
L
6
5
Assembly Instructions
5
P
P
J
J
J
J
P
P
L
6
7
J
J
P
P
5
6
11
11
L
6
11
Assembling guard rails
a: To assemble the rear
guard rail, locate internal
bracket inside guard
rail as shown.
Secure using screw .
Locate rear guard rail
onto guard rail and
secure using fixings
and .
b: To assemble the front
guard rail,
repeat the
steps from a: above,
using front guard rail
and remaining guard rail
.
11
6
L
6
5
J
P
7
6
a:
b:
Page 7
Assembly Instructions
Assembling rear guard
Two people are needed
here.
With help, stand both
side frames upright.
Assemble the rear guard
rail and in between
the side frames as shown.
Note:
Do not fully tighten
any screws
during the assembly.
Secure at the top using
fixings and as
shown.
Secure at the bottom
using fixings ,
and as shown.
Note:
Plastic washers
are located in between
the rear guard and the
side frames.
With help, fit feet to
corner posts at the
rear of the bunk.
Note: Ensure the feet
extend out to the rear of
the bed as shown.
Warning:
The bunk bed
is heavy. Lift
with care.
5
B
C
E F G H
J
F
6
B
C
H
E
J
E
G
F
5
6
2
2
1
1
2
B
C
H
E
F
G
6
J
E
F
6
Q
Q
Q
2
Feet to extend to rear.
Rear
Front
Q
2
Step 3
Page 8
Assembly Instructions
Step 4
7
E
H
F
G
J
B
C
1
B
C
J
E
H
F
G
Assembling front
guard
At this stage, choose if
you want the ladder on the
right hand side or left
hand side.
According to which side
you want the ladder,
assemble front guard rail
and in between the
side frames as shown.
Secure at the top using
fixings and .
Secure at the bottom
using fixings ,
and .
Plastic plugs can be
used to cover the
un-used holes in corner
post as shown.
6
E F G H
J
6
E
F
E
F
Alternative assembly
B
C
6
7
7
M
1
M
M
1
Page 9
Assembly Instructions
8
9
L
9
L
Step 5
Assembling slats
Fit slats in the very last
fixing holes at each end of
the bed.
Note:
The arrow labels
on
slats must point
outside.
Note:
Slats have been
labelled for easier
identification.
9
9
9
9
7
Slats at
each end
9
3
Arrow label to
point outside
Page 10
Assembly Instructions
Step 6
9
10
12
12
12
10
J
12
N
N
N
J
12
J
N
J
12
N
10
10
J
J
External bracket
Outside
Inside
OR
7
12
Assembling slats
Locate external brackets
over the joints in the
front and rear guard rails.
Note: Depending on
which way round you have
assembled the front guard
rail, external bracket
may be visible on the
outside of the bed.
With help, place two slats
on top of the external
brackets and secure using
Fixings and .
N
Page 11
Assembly Instructions
Step 8
7
10
Assembling slats
Assemble remaining
slats using screws
as shown
.
10
L
10
L
2
2
L
10
L
J
C
K
8
7
8
J
C
K
Step 7
Attaching ladder
Assemble ladder to
front guard using
fixings and .
Fixings are located
inside the frame as
shown.
C
J
K
J
8
7
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6400 800
Home Retail Group. 489-499 Avebury Boulevard. Saxon Gate West. Central Milton Keynes. MK9 2NW
Assembly is complete.
Loading...