Argos Linear - 1 Drawer 2 Door Robe ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Dimensions
Width - 79.5cm
Depth - 49cm
Height - 184cm
Linear - 1 Drawer 2 Door Robe
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 06/06/14
Important - Please read these instructions fully before starting assembly
224/8877
258/7820
246/7294
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 46kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.
• Dispose of all packaging carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
1
2
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
6
7
Left Side (DF148)
(1763 x 466mm)
Right Side (DF149)
(1763 x 466mm)
Base (DF154)
(791 x 468mm)
Shelf (DF155)
(759 x 465mm)
3
Top (DF150)
(795 x 490mm)
9
Door (DF156)
(1565 x 390mm) x 2
Drawer Back (W708-124)
(708 x 124mm)
Back (X1784-785)
(1784 x 785mm)
Drawer Base (T719-367)
(719 x 367mm)
Drawer Front (DF145)
(783 x 187mm)
Left Drawer Side (W370-124LH)
(370 x 124mm)
Right Drawer Side (W370-124RH)
(370 x 124mm)
8
10
11
12
13
Hanging Rail (FHR751)
(751mm long)
5
3
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number
and the reference numbers below)
B C
D E F
G H
Small locking nut (F3) x 2
Nail (F51) x 34
I
A
Wooden dowel (F22) x 8 Metal dowel (F901) x 10
Large locking nut (F900) x 8
Knock-in Peg (F171GY) x 4
M
R Runner (F160) x 1
b
L Runner (F161) x 1
M
c
L Runner (F159) x 1
M
a
R Runner (F162) x 1
M
d
350mm long
40mm Screw (F910) x 4
N
13mm Screw (F52) x 6
J
13mm Screw (F79) x 15
13mm Screw (F63) x 22
K
L
Wedgefix (F639) x 4
N
O
R
38mm Screw (F81) x 8
Q
Rail Holder (F891) x 2
N
P
Foot
(F233) x 4
Bracket (F327) x 1
Hinge (F518) x 6
Hinge plate (F523) x 6
NPNPS
Handle (F283) x 1 -
780mm long
NPNPT
Handle (F331) x 1 -
1560mm long
7
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
B
B
B
C
C
C
C
9
10
Step 2
Prepare the drawer front
Screw 2 metal dowels into the drawer front .
Note: Tighten the metal dowels up fully against the panels.
B
7
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
C
9
10
Attach the drawer sides to the drawer front
Push the left drawer sides . and right drawer sides . onto the back of the drawer front .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
9
10
7
C
C
9
10
B
B
7
8
9
10
7
E
E
Assembly Instructions
5
Step 4
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
Step 5
Fit the drawer back
Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
Step 6
11
9 10
7
8
9 10
11
8
8
E
9 10
E
E
11
9
10
11
8
9
10
Fit the handle
Position the handle onto the top edge of the drawer front .
Fix the handle to the back surface of the drawer front using 5 screws .
S
7
S
J
7
J
J
J
J
J
S
7
Assembly Instructions
6
Step 7
Fit the wedgefixes
Turn the drawer assemblies over and slide 4 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
L
L
L
L
L
L
Fit runners to the drawers
Fit the runner to the bottom edge of the left drawer side , as shown, making sure that it is pushed up against the back of the drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .
Fit the runner to the bottom edge of the right drawer side using the same method.
10
M c
9
7
K
M d
K
K
M d
Runners must be
pushed up against
the drawer front
9
7
Step 8
M c
10
K
K
Finished
front edge
Finished
front edge
Finished
front edge
A
A
Assembly Instructions
7
Step 9
M a
I
Finished front edge
I
1st screw
2nd screw
I
3rd screw
M a
Finished front edge
K
10mm
A
D
Prepare the left side
a: Fit the runner to
the left side .
The 1st screw uses the 2nd hole in from the front of the runner.
The 2nd and 3rd screws . use the holes that line up with the other panel holes.
Tap 4 wooden dowels into the left side .
b: Fit a screw into
the 2nd hole in at the top of the runners .
Screw 2 metal dowels into the left side .
Insert 2 large locking nuts into the left side . .
c: To fit the rail holder
screw through the top hole with screw and into the mark hole drilled in the left side . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.
Fit 3 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.
A
D
1
1
M a
1
I
I
K
M a
I
M a
I
I
K
A
A
P
P
P
P
D
D
B
B
K
N
K
N
K
K
N
1
1
1
B
1
N
K
K
1
P
1
Note: Wooden dowels must not stick out from the edge
by more than 10mm or they may damage other panels.
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
a:
b:
c:
A
A
Assembly Instructions
8
Step 10
Prepare the left side
a: Fit the runner to
the right side .
The 1st screw uses the 2nd hole in from the front of the runner.
The 2nd and 3rd screws . use the holes that line up with the other panel holes.
Tap 4 wooden dowels into the right side .
b: Fit a screw into
the 2nd hole in at the top of the runners .
Screw 2 metal dowels into the right side .
Insert 2 large locking nuts into the right side . .
c: To fit the rail holder
screw through the top hole with screw and into the mark hole drilled in the right side . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.
Fit 3 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.
A
D
2
2
M b
2
I
I
K
M b
B
2
N
K
K
2
P
2
M b
I
Finished front edge
I
1st screw
2nd screw
I
3rd screw
I
I
M b
I
a:
b:
c:
A
A
Finished
front edge
Finished
front edge
Finished
front edge
K
D
D
B
B
P
P
P
P
K
K
N
2
2
2
M b
Finished front edge
K
Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
9
Step 11
D
D
D
D
Finished
front edge
D
6
6
Fit the shelf to the right side
Push the shelf onto the right side .
Use a screwdriver to tighten the 2 large locking nuts fitted to the shelf .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
2
6
D
D
6
Step 12
Fit the left side to the shelf
Push the left side onto the shelf .
Use a screwdriver to tighten the 2 large locking nuts fitted to the shelf .
6
1
D
6
Step 13
2
6
6
1
B
D
Prepare the shelf
Insert 4 large locking nuts into the shelf .
Finished
front edge
Assembly Instructions
10
Step 14
Polystyrene
block
Polystyrene
block
Prepare the top
Screw 4 metal dowels into the top .
B
3
Fit the right side to the top
Note: To make it easier to fit the top and base panels, place polystyrene blocks from the packaging underneath the side panels to raise the assembly.
Push the top onto the assembly.
Use a screwdriver to tighten the 4 large locking nuts fitted to the left side and right side .
3
D
1
2
Step 15
B
B
B
B
Finished
front edge
3
1
3
2
Assembly Instructions
11
Step 16
Step 17
Fit the feet
Fit the feet to the base using screws .
H
R
4
R
H
H
R
H
H
R
H
H
R
H
H
4
G
Fit the base
Fit the base onto the assembly using 4 screws . .
4
G
G
G
G
4
Assembly Instructions
12
Step 18
Step 19
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the outside edges of the back .
Note: Nails should be evenly spaced out.
Stand the unit up for the next step.
13
F
13
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
b:
F
yy
yy
xx
xx
13
Warning: The unit is heavy. Lift with care.
5
5
N
Fit the hanging rail
Push the hanging rail into the rail holders fitted to the side panels.
5
N
Assembly Instructions
13
Step 20
Step 21
Fit the drawer
Slide the wheels of the runners fitted to the drawer, over the wheels of the runners fitted to the side panels and push the drawer into position.
Side
panel
Drawer
Fit a handle to 1 of the doors
Position the handle onto the side edge of 1 of the doors .
Fix the handle to the back surface of the door . using 9 screws .
T
12
T
J
12
J
J
J
J
J
J
J
J
J
12
T
x 1
Assembly Instructions
14
Step 22
Q
K
K
90
Q
Q
K
K
Q
K
K
Fit the hinges to the doors
Note: To make it easier to fit the hinges and to protect the handle, place polystyrene blocks from the packaging underneath the door with the handle to raise it up.
Push fit 3 hinges into each of the doors .
Secure each hinge with 2 screws .
Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.
K
Q
12
12
Polystyrene
blocks
Handle
Polystyrene
blocks
Polystyrene
block
Q
K
K
Q
K
K
Q
K
K
12
x 1
x 1
Assembly Instructions
15
Step 23
Fit the doors
Note: The easiest way to attach each door is to fit the top hinge first, then align and fit the other hinges.
a: Push the hinge
onto the front part of the hinge plate . The recess at the bottom of screw B goes into the slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.
c: The hinge must be
flat against the hinge plate prior to any adjustment.
d: The hinge must
NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.
Q
Q
Q
P
P
P
Q
P
12
a: b:
c: d:
P
Q
P
P
B
P
Q
Q
Q
A
Q
P
B
12
12
Note: You can choose which side to fit the door with the handle.
Assembly Instructions
16
Step 24
Adjust the doors if needed
a: Before adjusting the
doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.
b: Height adjustment.
Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.
c: Forward and Back
adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.
d: Sideways
adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.
b:
c:
d:
a:
A
A
B
C
Assembly Instructions
17
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 25
Top of Unit
WALL
WALL
Back of Unit
Fit the bracket
To prevent possible overbalancing, we recommend that this unit is secured to a suitable wall by use of the bracket fitted to the top of the unit.
Fixings are not supplied, as they will need to suit the wall type and the length of screw will depend on the distance from the back of the unit to the wall.
Fix the bracket loosely onto the top of the unit using screw and mark the wall for the wall fixing.
Swivel the bracket away from the wall and drill a hole in the wall using a suitable drill bit and fit your wall fixing.
Swivel the bracket back and fix the bracket to the wall, then tighten screw .
Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Warning: The unit is heavy. Lift with care.
Assembly is complete
O
O
J
O
O
J
O
J
O
O
ALR3055
Loading...