Arcam CR80 User Manual

ARCAM
• CR80 Universal Remote p.2
• CR80 Télécommande Universelle p.13
TABLE OF CONTENTS
INSTALLING BATTERIES
INTRODUCTION INSTALLING THE BATTERIES FEATURES AND FUNCTIONS
SEARCHING FOR YOUR CODE
learning a FUNCTION
RE-ASSIGNING DEVICE KEYS CHANGING VOLUME LOCK TROUBLE SHOOTING MANUFACTURER'S CODES
Setup Codes for TV Setup Codes for VCRs Setup Codes for Cable Converters Setup Codes for Satellite or DBS Receivers Setup Codes for CD Players Setup Codes for DVD Players Setup Codes for LO Players Setup Codes for Cassette Decks Setup Codes for Stereo Tuners or Receivers Setup Codes for AV Processors Setup Codes for Home Automation Setup Codes for DBS Audio Services Setup Codes for Video Accessories
INTRODUCTION
The ARCAM CR80 is the complete solution for all of your remote control requirements. It is designed to operate up to eight devices with the emphasis on features and functions of Arcam components.
The ARCAM CR80 is also customizable to allow for key configurations that meet your specific needs. It*s also packed with the following features:
• Preprogrammed technology for easy setup
• Designed for use with up to eight devices
• Inclusive audio library
• Upgradability
• Backlighting
• Learning capability
This manual provides a basic overview on how to set up and operate the ARCAM CR80. Please read the following instructions to see how easy setup is.
• The CR80 remote control is custom manufactured for Arcam by Universal
Electronics, Inc.
26 26 26 27 27 27 27 27 27 27
10
11
12
24 25 26
2
3
3 4 5
6
7
8
9
1 On the back of the ARCAM CR80. push the tab and lift off the
battery cover.
2 Obtain two (2) fully-charged AA alkaline batteries. Match
the + and - marks on the batteries to the + and - marks in the battery case, then insert the new batteries.
3 Press the battery cover back into place. The tab should click when
the cover is locked.
4 Test the unit by pressing PWR and any device key (e.g., AUX, CBL,
VCR, etc.). If the batteries are inserted correctly, the LED will blink once upon each keypress.
NOTE: When batteries need replacement, the ARCAM CR80 will blink twice with every keypress. Simply replace them and the remote control will be restored to its full functionality, including favorite settings.
FEATURES AND FUNCTIONS
Basic Operation
The Arcam CR80 is pre-programmed to operate Arcam amplifiers, DVD players, CD players and AM/FM tuners. For full operating details, please read the rest of the manual.
To control an AV component, first press the relevant key in the SELECT DEVICE area of the remote.
In addition, this remote control contains a library of remote codes for other manufacturers of AV system components, listed in the back of this manual.
The CR80 also has the capability of learning remote functions that are not available in the code library. In order to make best use of the limited me mory available for learning, we strongly recommend that you use the library codes where possible for your non-Arcam components, and then
learn new codes for non-library components.
11
13
16
19
5 -
8 ^c
© © ©
03* ' jKl5^ C^i
CZ5iH^S <3^
O'- ■
Controlling AV Components, General Use
1 The LED (red light) blinks to show that the remote control is
working and is sending signals.
2 Use SET for all programming sequences.
3 Press PWR once to turn on or off the selected home entertainment
component.
4 Press CBL, DVD, VCR, TV, SAT, CD, AMP, or AUX In the "Select
Device" section once to select a home entertainment component to control.
5 Use the keypad (0 - 9) to directly select channels (for example, 09 or
31), except for the AMP mode, since these keys select the input of the amplifier.
6 Press MUTE once to turn the sound off or on.
7 Press ENTER once after entering channel numbers on some TV
7
10
12
14
15
18
models.
8 Use VOL + (or VOL -) to raise (or lower) the audio volume.
9 Use CH + (or CH -) to select the next higher (or lower) channel, or
for next (or previous) track.
10 Press LAST once to recall the last channel and to page back one
screen in the main menu.
11 Press SLEEP to activate your TV or AV component's sleep timer. On
some TV's you may have to operate Sleeptimer in another way,
through Menu for example.
12 Press A'B once to select this function on your chosen component.
13 Use GUIDE to display the program guide.
14 Use EXIT to exit out of the selected component's menu or guide. Use
15 Use UP, DOWN, LEFT, RIGHT for menu navigation and OK to choose
16 Use INFO to display current channel and program information.
17 Press MENU to access the menu of your chosen component,
18 Use the transport keys to control your VCR, or CD or DVD player.
19 Use these keys for specific features on your dedicated components.
For programmed devices this key actions an INPUT command.
the cursor keys to move the cursor in the program guide and menu screens.
options from your selected component's menu or guide,
Loading...
+ 6 hidden pages