Installation Guide SMT 2200/3000 VA
Input/Output Hardwir e Kit
Safety
Adhere to all national and local electrical codes. A certified electrician must perform all electrical
connections.
1. Disconnect equipment connected to the UPS.
2. Press the OFF button located on the front of the UPS.
3. Disconnect the bat teries in the UPS.
4. Disconnect the UPS from utility power.
NOTE: When removing the panels from the UPS, note which cable is connected to the AC input. There are two
4-pin connectors on the UPS and they are not interchangeable.
Inventory
Note: The illustrations in this document may differ slightly from the actual hardware.
Terminal block
Termina l bl ock la bel
2 screws secure the
terminal block to the UPS
Input panel
Output panel
Blank panel
4 grounding screws 8 screws
secure input, output, and
blank panels to the UPS
2 wire nuts
Installation
A
Note: It is recommended that the input and output cables be connected to the terminal block prior to
installing the terminal block in the UPS.
Remove the five screws that secure the factory
installed PDU panels to the UPS.
Save the screws.
Disconnect the PDU input a nd output cables as
shown in the diagram.
C Input Connector
su0669b
Secure the replace ment input and output panels
(supplied), to the UPS. Sec ure the panels with
four of the screws removed from the factory
installed PDU panel.
Instal l ap p r op r i at e str a in r el ie f clamps (no t
supplied), to the input and output panels as
shown in the diagram.
Hardwire Kit SMT2200/3000 VA 100/120/ 230 VAC Tower2
su0670a
Secure the terminal block and label to the UPS
Ground
Ground
Hot
Output Line1
Input Line2
or Neutral
with two screws (supplie d), as shown in the
diagram.
su0671a
Refer to the diagram below. Use th e screws supplied. Connect the ground wires with the grounding s crews. Connect the
input and output cables.
Primary
Green Wire
Input Line1
su0672a
Output Line2
or Neutral
Hardwire Kit SMT2200/3000 VA 100/120/230 VAC Tower 3
Connect the terminal block and UPS connectors as shown in the diagram.
A
AC Input
NOTE: The two pin connector will not be utilized with the replacement input and output panels.
Connector
C Input
Connectors
su0673b
Secure the blank panel to the UPS with three
screws (supplied).
su0674a
APC Worldwide Customer Support
Customer support for this or any other APC product is available at no charge in any of the f ollowing ways:
• Visit the APC Web site to access documents in the APC Knowledge Base and to submit customer
support requests.
– www.apc.com (Corporate Headquarters)
Connect to localized APC Web sites for specific countries, each of which provides customer
support information.
– www.apc.com/support/
Global support searchi ng APC Knowledge Base and using e-support.
• Contact the
• Local, country-specific centers: go to www.apc.com/support/contact for contact information.
For information on how to obtain lo cal custo mer supp ort, cont act the APC representa ti ve or other distri butors from whom
you purchased your APC product.
APC Customer Support Center by telephone or e-mail.
Hardwire Kit SMT2200/3000 VA 100/120/ 230 VAC Tower4
Customer support and warr anty information is availabl e at the APC Web site, www.apc.com.
© 201 1 A P C by Schneider Ele ctric. APC, the APC logo, and Smart-UPS are owned by Schneider
Electr ic Industri es S.A.S., American Power Conversion Corporation, or their affiliated com panies.
All othe r trademarks ar e property of th eir respective owners.
990-3933
6/2011
Loading...