APC BX750MI-GR, BX2200MI, BX1200MI, BX1200MI-GR, BX2200MI-GR Manual [EN]

...

Page 1

User Manual Back-UPS

BX Series 750VA, 950VA, 1200VA, 1600VA, 2200VA

IMPORTANT SAFETY INSTRUCTIONS

Read the instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service or maintain it. The following special messages may appear throughout this document or on the equipment to warn of potential hazards or to call attention to information that claries or simplies a procedure.

The addition of this symbol to either a “Danger” or “Warning” safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.

DANGER

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in death or

serious injury.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or

moderate injury.

NOTICE

NOTICE is used to address practices not related to physical injury.

Product Handling Guidelines

< 18 kg < 40 lb

18-32 kg 40-70 lb

32-55 kg 70-120 lb

> 55 kg > 120 lb

Page 2

Safety and General Information

SAVE THESE INSTRUCTIONS –

This manual contains important instructions that should be followed during installation and maintenance of the UPS and batteries. Inspect the package contents upon receipt. Notify the carrier and dealer if there is any damages.

 This UPS is intended for indoor use only.  Mains socket outlet that supplies the UPS shall be installed near the UPS and shall be easily

accessible.

 UPS must be connected to an earthed mains socket outlet.

 Servicing of batteries should be performed or supervised by personnel knowledgeable about

batteries and required precautions. In this case, batteries is not user-replaceable.

 When replacing battery the UPS must be OFF, and its AC inlet unplugged.  CAUTION Do not dispose of batteries in a re. The batteries may explode.

 CAUTION Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries

according to the instructions.

 Do not open or mutilate batteries. They contain an electrolyte that is toxic and harmful to the skin

and eyes.

 Failed batteries can reach temperatures that exceed the burn thresholds for touchable surfaces.

 CAUTION A battery can present a risk of electrical shock and high short circuit current.

The following precautions should be observed when working on batteries.

a. Remove watches, rings or other metal objects. b. Use tools with insulated handles. c. Wear rubber gloves and boots. d. Do not lay tools or metal parts on top of batteries. e. Disconnect the charging source prior to connecting or disconnecting battery terminals. f. Determine if battery is inadvertently grounded. If inadvertently grounded, remove source from

ground. Contact with any part of a grounded battery can result in electrical shock. The likelihood of such shock can be reduced if such grounds are removed during installation and maintenance.

 The battery in the Back-UPS Series is not user-replaceable.

Radio Frequency Warning

This is a category C2 UPS product. In a residential environment, this product may cause radio interference, in which case the user may be required to take additional measures.

Battery Replacement

CAUTION

RISK OF HYDROGEN SULPHIDE GAS AND EXCESSIVE SMOKE

Replace the battery at least every 5 years. Replace the battery immediately when the UPS indicates battery replacement is

necessary. Replace battery at the end of its service life. Replace batteries with the same number and type of batteries as originally installed in

the equipment. Replace the battery immediately when the UPS indicates a battery over-temperature

condition, or UPS internal over-temperature, or when there is evidence of electrolyte

leakage. Power off the UPS, unplug it from the AC input, and disconnect the batteries.

Do not operate the UPS until the batteries have been replaced.

Failure to follow these instructions can result in injury.

The battery in the Back-UPS is not user-replaceable. Contact SEIT Technical Support for a list of authorized service centers near you. For the recycling battery information, please go to apc.com/us.

Back-UPS BX Series 750VA, 950VA, 1200VA, 1600VA, 2200VA

Page 3

Product Description

The APC by Schneider Electric Back-UPS offers power and surge protection for wireless networks, computers, gaming consoles and other electronics in your home or business. This UPS supply battery backup during outages and unstable voltage fluctuations, as well as provide protection from damaging surges and spikes. It’s equipped with data line surge protection which safeguards your equipment and valuable files from “back door” surges traveling along data line. They are the choice helps to protect your sensitive electronics.

Place and Power On

1. Place the Back-UPS to avoid:

 Direct sunlight  Excessive heat  Excessive moisture  Excessive dust/dirt

For operation, please place the unit on the floor.

2. Connect the battery by pulling the battery handle up,

and then pushing it into the unit.

3. Connect equipment to the UPS. Avoid using extension cords.

4. Plug the Back-UPS power cord directly into a wall outlet, not into a surge protector or power strip.

5. Press the ON/OFF button to turn on the unit.

The green “Power On” indicator confirms that the Back-UPS is on and ready to provide protection. The Back-UPS should charge for at least 24 hours to ensure sufficient runtime. The unit is being charged whenever it is connected to AC power, whether the unit is turned ON or OFF.

Operational Features

Automatic Voltage Regulation (AVR)

Automatic Voltage Regulation boosts/trims the AC voltage when it drops/exceeds levels. This allows the equipment plugged into the unit to operate during low/high voltage conditions, conserving the battery power in the event of a power cut. The Back-UPS will switch to battery power if the input voltage level becomes too low/high for the Automatic Voltage Regulation to compensate, or if the AC power is distorted.

PowerChute Personal Edition Software

To install PowerChute Personal Edition (PCPE) software, connect a USB cable to the data port on the UPS and the other end to a computer with access to the web.

On the computer, go to www.apc.com/tools/download. Select “Software Upgrades - PowerChute Personal Edition” in the “Filter by Software/Firmware” drop down menu. Select the appropriate operating system. Follow directions to download the software.

Quick Mute

The Back-UPS is able to temporarily mute user correctable audible alarms such as On Battery. During such audible alarms, a short press (less than 2 seconds) of the POWER button will temporarily mute the audible alarm until the condition has been reset. A short double beep will confirm that Quick Mute has been activated. Pressing the POWER button for more than 2 seconds will turn off the UPS. Other critical events such as Battery replacement and Charger notification can not be temporarily muted. The unit in these cases must be turned off.

Voltage Sensitivity Adjustment

The Back-UPS detects and reacts to line voltage distortions in PCPE by transferring to battery backup power to improve protection of connected equipment. In situations where either the Back-UPS or the connected equipment is too sensitive for the input voltage level, it is necessary to adjust the transfer voltage. Refer to user guide of PowerChute Personal Edition.

Back-UPS BX Series 750VA, 950VA, 1200VA, 1600VA, 2200VA

Page 4

Features

ON/OFF button with indicator

Input power cord

Battery backup and surge protected outlets

Battery connector

Circuit breaker

AC power inlet with AC fuse

*only for model with IEC outlet

USB data port

In/Out Ethernet surge-protected ports

Model

Output Type

and Quantity

Model

Output Type and Quantity

Model

Output Type and Quantity

Model

Output Type and Quantity

BX750MI-GR BX950MI-GR

BX750MI

BX1200MI BX1600MI BX2200MI

x 6

BX1200MI-MS

x 4 x 1

x 4

BX750MI-AZ

x 3

BX950MI

x 6

BX950MI-AZ

BX750MI-FR

x 4

x 3

BX750MI-MS

BX950MI-FR

BX750 BX950

BX1200MI-GR BX1600MI-GR BX2200MI-GR

x 4

BX1200MI-FR BX1600MI-FR BX2200MI-FR

x 4

BX1600MI-MS BX2200MI-MS

x 2 x 1

x 4

BX950MI-MS

x 2 x 2

BX1200MI-AR/AZ BX1600MI-AR/AZ

BX2200MI-AR

x 4

IEC jum pe r Cable f or P C connect io n(1.2 m) *only f or t he mode l wi th IEC outl et

Back-UPS BX Series 750VA, 950VA, 1200VA, 1600VA, 2200VA

BX1600MI

BX2200MIBX1200MI

USB com mu nicat io n cable (1. 2m )

BX1600MI BX2200MI

H C

Page 5

Specifications

Model

Input

Output

Protection

Battery

Physical

Temperature

IP Rating

Voltage

Frequency

Brownout Transfer

Over-voltage Transfer

UPS Capacity (total)

Voltage On Battery

Frequency - On Battery

Transfer Time

AC Input Circuit Breaker (only for GR, FR, MS and AR models)

AC Input Fuse

Type (maintenance-free)

Average Life

Typical Recharge Time

Net Weight

Dimensions (Hx Wx D) c m

Shipping Weight

Shipping Dimensions (H x Wx D) cm

Operating

BX750MI BX950MI BX1200MI BX1600MI

220-240 Vac

50 Hz or 60 Hz (auto-sensing)

140 Vac, typical

300 Vac, typical

750VA/410W

5A/250Vac 7A/250Vac 10A/250Vac 12A/250Vac 15A/250Vac

T 5A L 250Vac

12V, 9AH x 1

lead acid

The battery typically lasts for three to ve years. Environmental factors impact battery backup life. Elevated temperatures, high humidity, poor quality mains power, and frequent, short duration discharges will shorten battery life.

The battery in the Back-UPS Series is not user-replaceable. Contact SEIT Technical Support for a list of authorized service centers near you.

5.9 kg

950VA/520W

T 8A L 250Vac

12V, 9AH x 1

lead acid

6.1 kg5.4 kg 7.6 kg 10.3 kg

16 x12 x 35.5

6.6 kg

25 x 19.7 x 43

1200VA/650W 1600VA/900W

230 Vac ±10%

50 Hz / 60 Hz ± 0.5Hz

6ms typical, 10ms max.

T 10A L 250Vac T 12A L 250Vac T 15A L 250Vac

12V, 9AH x 1

lead acid

8 Hours

8.6 kg

0 °C to 40 °C

12V, 7AH x 2

lead acid

19 x14 x 39

29.7 x 23.5 x 49.5

IP20

BX2200MI

2200VA/1200W

12V, 9AH x 2

lead acid

12.3 kg

13.3 kg11.3 kg

* The length of input power cord is 1.2m. For best operation, do not use output cable longer than 2m. ** The length of USB communication cable is 1.2m. For best operation, do not use communication cable longer than 3m.

Back-UPS BX Series 750VA, 950VA, 1200VA, 1600VA, 2200VA

Page 6

Status Indicators

LED

(Off during 4 beeps)

Flashing Constant beeping

Off

Audible Alarm

Off

Constant Tone

Constant beeping

(every 1/2 second)

4 beeps repeated

every 30 seconds

(every 1/2 second)

Constant tone

Short beep every

4 seconds

Constant Tone

Condition

On-line - The Back-UPS is supplying AC power to the

connected equipment

On Line Overload - The power being used by the connected equipment has exceeded the capacity of the unit. Disconnect some equipment.

Over-temperature Detected - The unit is overheating and will operate in AVR mode for 1 minute. The Back-UPS will shut down if the temperature is not lowered. Disconnect some of the connected equipment.

On-Battery - The Back-UPS is supplying battery power.

Low Battery - The Back-UPS is supplying battery power

and the battery is near a total discharge state.

Replace Battery Detected - The battery needs to be charged, or is at end of life.

Note:

- If the battery is disconnected, unplug the Back-UPS from AC source and then turn it off. Refer to the section “Place and Power On” on page 3.

- If battery needs replacement, refer to the section “Battery Replacement” on page 2 for details.

Low Battery Shutdown - During On Battery operation the battery power was almost completely exhausted, and the Back-UPS is waiting for AC power to return to normal.

On Line Overload Fault - The connected equipment requires more power than provided by the Back-UPS. Unplug devices one at a time to remove overload.

If the detected problem is not corrected, contact SEIT Technical Support

Charger Detected Fault - Back-UPS has an internal problem detected, and is no longer powering the load. Contact SEIT Technical Support

Long beep every

4 seconds

Back-UPS BX Series 750VA, 950VA, 1200VA, 1600VA, 2200VA

Over-temperature Detected Fault - The Back-UPS has overheated and has shut down. Unplug connected devices one at a time or wait for a few hours for system to cool down.

Page 7

Troubleshooting

Detected Problem and Possible Cause

The Back-UPS will not turn on

The Back-UPS has not been turned on.

The Back-UPS is not connected to AC power, there is no AC power available at the wall outlet, or the AC power is experiencing a brownout or over voltage condition.

The battery is disconnected.

Connected equipment loses power

A Back-UPS overload condition has occurred.

The Back-UPS battery is completely discharged.

Connected equipment does not accept the step-approximated sine waveform from the Back-UPS.

The Back-UPS may require service.

The ON/OFF button is green and ashing every 30 seconds. 4 beeps repeated every 30 seconds.

The Back-UPS is operating on battery power.

The ON/OFF button ashes green and constant beeps every 1/2 second.

The Back-UPS battery has approximately empty and will shutdown

The Back-UPS has an inadequate battery runtime

The battery is not fully charged. The battery is near the end of useful life and should be replaced.

The UPS and outlets are but the UPS keeps beeping once every 4 seconds. The alarm off audible will mute after 32 seconds.

The UPS have shut down due to low battery, but control power exists.

Press the ON/OFF button.

Make sure the power cord is securely connected to the wall outlet, and that there is AC power available at the wall outlet. Where applicable, check that the wall outlet is switched on.

Refer to the “Place and Power On” on page 3.

Remove all nonessential equipment connected to the outlets. One at a time reconnect equipment to the Back-UPS. Charge the battery for 24 hours to make sure it is fully charged. If the overload condition still occurs, replace the battery.

Connect the Back-UPS to AC power and allow the battery to recharge for ten hours.

The output waveform is intended for computers and peripheral devices. It is not intended for use with motor driven equipment.

Contact Schneider Electric Technical Support for