PROLINE® ULTRA-LOW NOx
COMMERCIAL-GRADE RESIDENTIAL
COMMERCIAL-GRADE
RESIDENTIAL GAS WATER HEATERS
INTELLIGENT CONTROL LOGIC
• The internal microprocessor provides
enhanced operating parameters and tighter
differentials for precise sensing and faster
heating response to optimize performance.
• Uses a thermopile to generate the power
needed to operate the electronic gas control
without requiring an external power source
• The electronic gas control incorporates an
LED status indicator that monitors system
operation & service diagnostics.
HIGH ENERGY FACTORS
• Eco-friendly non-CFC foam insulation, heat
traps and specially designed combustion
chamber combine to produce a high Energy
Factor for maximum savings on operating
costs.
GREEN CHOICE® GAS BURNER
• Enhanced Ultra-low NOx burner complies
with SCAQMD Rule 1121 and other air
quality management districts with similar
requirements for NOx emissions of less than
10 ng/J.
DYNACLEAN™ DIFFUSER DIP TUBE
• Helps reduce lime and sediment buildup and
maximizes hot water output. Made from
long-lasting PEX cross-linked polymer.
COREGARD™ ANODE ROD
• Our anode rods have a stainless steel core
that extends the life of the anode rod
allowing superior tank protection far longer
than standard anode rods.
PUSH-BUTTON PIEZO IGNITOR
• Makes lighting the pilot fast and easy with
one-hand push-button spark ignition.
HEAT TRAP NIPPLES
• Factory-installed for faster installation
BLUE DIAMOND® GLASS COATING
• Provides superior corrosion resistance
compared to industry standard glass lining.
ENHANCED-FLOW BRASS DRAIN
VALVE
• Our residential water heaters have a solid
brass, tamper resistant, enhanced-flow, ball
type, drain valve.
• Uses a standard female hose fitting that
allows for fast and easy draining during
maintenance.
• Designed for easy operation, this valve
includes an integral screwdriver slot that
features a ¼ turn (open/close) radius, which
not only permits full straight-through water
flow but also a quick and positive shut off.
CODE COMPLIANCE
• Meets UBC, CEC and HUD National Codes.
• Meets the thermal efficiency and standby
loss requirements of the U.S. Department of
Energy and current edition of ASHRAE/IES
90.1.
• Complies with the Federal Energy
Conservation Standards effective April 16,
2015, in accordance with the Energy Policy
Conservation Act (EPCA), as amended.
CSA CERTIFIED AND ASME RATED T&P
RELIEF VALVE
• Top-mounted T&P relief valve available as
option.
DESIGN-CERTIFIED BY CSA
INTERNATIONAL
• Certified at 300 PSI test pressure and 150
PSI working pressure. Listed according to
ANSI Z21.10.1-CSA 4.1 standards governing
storage tank-type gas water heaters.
6-YEAR LIMITED TANK AND PARTS
WARRANTY
• For complete information, consult written
warranty or go to hotwater.com.
©February 2017 A. O. Smith Corporation. All rights reserved.
www.hotwater.com | 800-527-1953 Toll-Free USA | A. O. Smith Corporation | 500 Tennessee Waltz Parkway | Ashland City, TN 37015
Page 1 of 2
AOSRG47001
COMMERCIAL-GRADE
RESIDENTIAL GAS WATER HEATERS
BTU
Model Number
TALL MODELS
GUC-30 30 55 0.63 33,000 34 61-3/4 58 16 12 8 51-3/4 N/A N/A 3 or 4 126
GUC-40 40 71 0.62 40,000 41 62 58-1/4 18 12 8 52 N/A N/A 3 or 4 125
GUR-40 40 71 0.63 40,000 41 62 58-1/4 20 12 8 52 N/A N/A 3 or 4 125
GUC-50 50 91 0.60 40,000 42 60-3/4 57-1/4 20 12 8 50-1/2 N/A N/A 3 or 4 148
GUR-50 50 91 0.62 40,000 42 60-3/4 57-1/4 22 12 8 50-1/2 N/A N/A 3 or 4 148
GURT-50L* 50 98 0.60 50,000 51 61 57-1/2 22 12-1/4 8 50-1/2 12-1/4 50-1/2 4 177
SHORT MODELS
GURL-40 40 69 0.62 40,000 41 51-1/2 47-3/4 22 12 8 41-1/4 N/A N/A 3 or 4 138
All models may be ordered from the factory with top T&P.
*Standard with side recirculating taps (model GURT-50L).
Most models approved for installation from sea level to 7,700 ft. elevation (except on GURT-50L which is approved to 5,400 ft.).
Dimensions and specifications subject to change without notice in accordance with our policy of continuous product improvement.
Gallon
Capacity
First Hour
Rating
Gallon
Energy
Factor
Natural
Input
Gas
Recovery @
90°F Rise
Gallon Per
Hour
A B C D E F G* H*
ANODE ROD
(OPTIONAL T&P
LOCATION)
HOT
CONNECTION
(ANODE OUTLETON
TOP T&P MODELS)
Dimensions in Inches Approx.
Draft
Hood
COLD
CONNECTION
Shipping
Weight
(lbs)
E
T&P VALVE
F
C
A
B
H
1/2" GAS
CONNECTION
D
G
Maximum Hydrostatic Working Pressure: 150 PSI
For technical information call 800-527-1953. A. O. Smith Corporation reserves the right to make product changes or improvements without prior notice.
www.hotwater.com | 800-527-1953 Toll-Free USA
AOSRG47001
Page 2 of 2