Antunes MS-155 Service Manual

MS-150/155

miracle steamers

owner’s manual

Manufacturing Numbers:

9100419, 9100420, 9100423, 9100425,
9100426, 9100428, 9100442, 9100450,

9100452, 9100456, 9100458, 9100459

www.antunes.com

P/N 1010454 Rev. F 12/16

Table of Contents

General .................................................. 2

Warranty Information ............................. 2

Service/Technical Assistance ................... 2

Important Safety Information ................. 3

Warnings ................................................ 3

Specifications ......................................... 4

Installation ............................................. 5

Electrical ................................................. 5

Plumbing ................................................ 5

Operating Instructions ............................ 6

Programming ......................................... 6

Hi-Limit Reset Button ............................. 7

Status Indicator LEDs ............................. 7

Fault Codes ............................................7

Daily Maintenance ................................. 7

Monthly Maintenance ............................ 8

Troubleshooting...................................... 9

Wiring Diagram ...................................... 11

Replacement Parts ..................................12

Limited Warranty .................................... 16

IMPORTANT

A.J. Antunes & Co. reserves the right
to change specifications and product
design without notice. Such revisions do
not entitle the buyer to corresponding
changes, improvements, additions or
replacements for previously purchased
equipment.

IMPORTANT

Keep these instructions for future ref­erence. If the unit changes ownership,
be sure this manual accompanies the
equipment.

GENERAL

This manual provides the safety, installation,
and operating procedures for the Miracle
Steamer. We recommend that all information
contained in this manual be read prior to
installing and operating the unit.

The Miracle Steamer is manufactured from the
finest materials available and is assembled to
our strict quality standards. This unit has been
tested at the factory to ensure dependable
trouble-free operation.

WARRANTY INFORMATION

Please read the full text of the Limited
Warranty in this manual.

If the unit arrives damaged, contact the car­rier immediately and file a damage claim with
them. Save all packing materials when filing a
claim. Freight damage claims are the respon­sibility of the purchaser and are not covered
under warranty.

The warranty does not extend to:

• Damages caused in shipment or dam­age as result of improper use.

• Installation of electrical service.

• Normal maintenance as outlined in
this manual.

• Malfunction resulting from improper
maintenance.

• Damage caused by abuse or careless
handling.

• Damage from moisture into electrical
components.

• Damage from tampering with, removal
of, or changing any preset control or
safety device.

SERVICE/TECHNICAL
ASSISTANCE

If you experience any problems with the
installation or operation of your unit, contact
Antunes Technical Service at 1-877-392-7854
toll free in the U.S.) or at 630-784-1000.

Fill in the information below and have it
handy when calling Antunes Technical Service
for assistance. The serial number is on the
specification plate located on the rear of the
unit.

Purchased From

Date of Purchase

Model Number

Serial Number

Manufacturing Number

Use only genuine Antunes replacement parts
in this unit. Use of replacement parts other
than those supplied by the manufacturer will
void the warranty.

2

P/N 1010454 Rev. F 12/16

IMPORTANT SAFETY
INFORMATION

Use the following guidelines for safe opera­tion of the unit.

• Read all instructions before using
equipment.

• For your safety, the equipment is fur­nished with a properly grounded cord
connector. Do not attempt to defeat
the grounded connector.

• Install or locate the equipment only
for its intended use as described in
this manual. Do not use corrosive
chemicals in this equipment.

• Do not operate this equipment if it
has a damaged cord or plug, if it is
not working properly, or if it has been
damaged or dropped.

• This equipment should be serviced
by qualified personnel only. Contact
Antunes Technical Service for adjust­ment or repair.

• Do not block or cover any openings on
the unit.

• Do not immerse cord or plug in water.

• Keep cord away from heated surfaces.

• Do not allow cord to hang over edge
of table or counter.

• Turn the power off, unplug the power
cord, and allow unit to cool down
before performing any service or
maintenance on the unit.

• The equipment should be grounded
according to local electrical codes to
prevent the possibility of electrical
shock. It requires a grounded recep­tacle with separate electrical lines,
protected by fuses or circuit breaker of
the proper rating.

• All electrical connections must be in
accordance with local electrical codes
and any other applicable codes.

• Do not clean this appliance with a
water jet.

WARNINGS

Be advised of the following warnings when
operating and performing maintenance on
this unit.

• If the supply cord is damaged, it must
be replaced by the manufacturer or its
service agent or a similarly qualified
person in order to avoid a hazard.

• Do not modify the power supply cord
plug. if it does not fit the outlet, have
a proper outlet installed by a qualified
electrician.

• Do not use an extension cord with this
appliance.

• Electrical ground is required on this
appliance.

• Check with a qualified electrician if
you are unsure if the appliance is
properly grounded.

• If a chemical cleaner is used, be sure
it is safe to use on cast aluminum.
Observe all precautions and warnings
on product label.

• Inspection, testing, and repair of elec­trical equipment should only be per­formed by qualified service personnel.

• This equipment is to be installed to
comply with the basic plumbing code
of the Building Officials and Code
Administrators, Inc. (BOCA) and the
Food Service Sanitation Manual of the
Food and Drug Administration (FDA).

• To ensure proper steaming character­istics, some calcium/mineral deposits
must be present on the generator
surface. If, during cleaning, the surface
does become free of calcium/mineral
deposits, add plain tap water to the
surface and allow it to boil off. This
may have to be repeated several times
to ensure proper steaming characteris­tics by creating a thin layer of deposits
on the surface.

• Do not use a sanitizing solution or
abrasive materials. The use of these
may cause damage to the stainless
steel finish.

• Chlorides or phosphates in clean­ing agents (e.g. bleach, sanitizers,
degreasers or detergents) could cause
permanent damage to stainless steel
equipment. The damage is usually in
the form of discoloration, dulling of
metal surface finish, pits, voids, holes,
or cracks. This damage is permanent
and not covered by warranty.

• The following tips are recommended
for maintenance of your stainless steel
equipment:

• Always use soft, damp cloth for

cleaning, rinse with clear water
and wipe dry. When required,
always rub in direction of metal
polish lines.

• Routine cleaning should be done

daily with soap, ammonia deter­gent, and water.

• Stains and spots should be

sponged using a vinegar solution.

• Finger marks and smears should be

rubbed off using soap and water.

• Hard water spots should be

removed using a vinegar solution.

P/N 1010454 Rev. F 12/16

3

SPECIFICATIONS

D

L

I

S

T

E

C US

I

N

T

E

R

T

E

K

C

A

READY

B

Model No.

MS-150

MS-155

Model &
Mfg. No.

MS-150

9100419

Saudi Arabia

MS-150

9100420

MS-150
9100423
9100425

MS-150
9100426

MS-150
9100428

MS-150
9100442

MS-155
9100450

MS-155
9100452

MS-155
9100456

MS-155
9100458

MS-155
9100459

Saudi Arabia

Width

(A)

21"

(533 mm)

21”

(533 mm)

Depth

(B)

21 3/8"

(543 mm)

17 1/8"

(435 mm)

Volts Watts Amps Hertz

230 3300 14.4 50/60

208 3300 15.9 50/60

120 1800 15.0 50/60

230 3300 14.4 50/60

230 3300 14.4 50/60

208 3300 15.9 50/60

208 3300 15.9 50/60

120 1800 15.0 50/60

230 3300 14.4 50/60

230 3300 14.4 50/60

230 3300 14.4 50/60

Height

(C)

10 1/4"

(260 mm)

10 1/4”

(260 mm)

Plug

Description

CEE 7/7

16 Amp. 250 Volt

NEMA 6-20P,

20 Amp., 250 Volt

NEMA 5-15P

15 Amp, 120 Volt

NEMA 6-20P,

20 Amp., 250 Volt

CEE 7/7

16 Amp. 250 Volt

NEMA 6-20P,

20 Amp., 250 Volt

NEMA 6-20P,

20 Amp., 250 Volt

NEMA 5-15P

15 Amp, 120 Volt

NEMA 6-20P,

20 Amp., 250 Volt

CEE 7/7

16 Amp. 250 Volt

IEC-309

16 Amp., 250 VAC

Pin & Sleeve

(Assembly Only)

Model &
Mfg. No.

MS-150
MS-155

Agency Approvals

A

T

T

I

I

O

N

N

A

S

C

US

L

I

S

L

D

I

D

S

E

T

E

T

CM

4

P/N 1010454 Rev. F 12/16

INSTALLATION

READY

1. Remove the unit and all packing
materials from the shipping carton.

2. The unit should come with the items
listed below:

• Owner’s Manual

• Spatula Assembly (MS-150 only)

• Drawer Assembly (MS-155 only)

NOTE: If any parts are missing or dam­aged, contact A.J. Antunes IMMEDIATELY
at 1-800-253-2991 or 1-630-784-1000.

3. Remove all packing materials and pro­tective coverings from the unit.

4. MS-150: Remove and wash the Wire
Trivet, Spatula, Spatula Liner, and
Drip Pan (Figure 1) in soap and water.
Rinse with clean hot water and allow
to air dry.

MS-155: Remove and wash the
Drawer, Drawer Liner with Rollers, and
Drip Pan (Figure 2) in soap and water.
Rinse with clean hot water and allow
to air dry.

5. Wipe all surfaces of the unit with a
hot, damp cloth.

NOTE: Do NOT use a dripping wet cloth.
Wring out before use.

6. MS-150 Models: Assemble the

Handle, Handle Guard and Mounting
Bolt to the Spatula (Figure 3).

7. Install the Wire Trivet into the side
slots on the Spatula.

8. Re-install all removed parts.

When placing the unit into service, pay atten­tion to the following guidelines:

Wire Trivet

Spatula

Figure 1. Washing Parts

(MS-150 Only)

Drip Pan

Drawer Liner

with Rollers

Figure 2. Washing Parts

(MS-155 Only)

Bolt

Handle

Drip Pan

Spatula Liner

Drawer

Wire Trivet

WARNING

Be sure to follow all the precautions, proce­dures, and safety steps listed in the Important
Safety Information section of this manual.

WARNING

All electrical connections must be in accor­dance with local electrical codes and any other
applicable codes.

ELECTRICAL

Plug the power cord into the appropriate
power outlet. Refer to the specification plate
for the proper voltage.

1. Place the unit on a sturdy, level table
or other work surface.

2. Turn off the power.

3. Ensure that the line voltage corre­sponds to the stated voltage on the
units specification label and power
cord warning tag. If you are unsure of
your Line Voltage, contact an electri­cian.

4. Connect the unit to the power supply.

PLUMBING

NOTE: Miracle Steamer models are
designed to use cold tap water. Distilled
water may be used to reduce calcium/
mineral deposit buildup and reduce main­tenance costs.

The MS-150/155 models have a self-contained
water tank. To fill the self-contained water
tank:

• Make sure power is off and the unit is
at room temperature.

• Do NOT block or cover any openings
on the unit.

• Do NOT immerse cord or plug in
water.

• Keep cord away from heated surfaces.

• Do NOT allow cord to hang over edge
of table or counter.

P/N 1010454 Rev. F 12/16

Spatula

Handle Guard

Figure 3. Assembling Handle

(MS-150 Only)

Tank

Tank Cover

Filter

Figure 4. Filling Water Tank

5

1. Open the Tank Cover on top of the
unit (Figure 4).

NOTE: Make sure filter inside tank is
installed properly.

2. Pour in cold tap water. The tank will
hold approximately 3 quarts (2.81
liters).

3. Close the Tank Cover.

NOTE: Do NOT overfill the unit’s water
tank. Only fill the tank to 90% full.