Antunes HWT-20 Specifications

Hand Wash Timer
Model: HWT-20

Features:

■ Runs on two AA batteries with an
estimated operating life of three years.

■ Mounts to any magnetic surface.

■ Encourages safe cleaning habits
to prevent the spread of infectious
diseases.

■ No user intervention required to
operate or activate the timer.

■ Helps employees conform to the
HACCP Safety requirement.

■ Assures customers that your
employees have a procedure for
healthy standards.

HWT-20

(P/N 9900640)

Dimensions: 6” x 1 1/4” x 4”

(152 mm x 32 mm x 102 mm)

■ Demonstrates to local health
inspectors your commitment to safe
cleaning practices in the restaurant.

What is the correct way

to wash your hands?

1. Wet hands and apply liquid soap.

2. Rub hands vigorously together and
scrub all surfaces.

3. Continue until the Hand Wash Timer
completes a full cycle. The soap
combined with vigorous scrubbing
helps dislodge and remove germs.

4. Rinse thoroughly and dry hands with a
clean towel.

www.ajantunes.com

Instructions for Use

Hand Wash Timer
Model: HWT-20

Follow these instructions for mounting the timer, changing the
batteries, and using the timer to properly wash hands.

MOUNTING THE HAND WASH TIMER

The Hand Wash Timer will mount directly to any flat steel surface
with the magnetic backing.

NOTE: Thoroughly clean the surface where the Timer is to
be mounted before proceeding. Observe the proper cleaning
procedures as required. Mount the Hand Wash Timer in the
location that best suits your operation.

1. If desired, use the Universal Mounting Bracket by care­fully peeling the backing from the adhesive and secure the
Universal Bracket to the chosen mounting surface.

NOTE: The adhesive is strong. Make certain to center it
properly before attaching.

2. Attach the Hand Wash Timer to the Universal Bracket or
directly to a magnetic surface.

CHANGING BATTERIES

The Hand Wash Timer comes with two AA batteries installed.
These batteries have an estimated operating life of 3 years. In the
event the batteries need to be changed, follow these steps:

1. Remove the four screws from the rear of the unit and

2. Remove and properly discard the two old AA batteries.

3. Install two new AA batteries. The unit should begin to oper­ate automatically.

4. Re-attach the back panel and secure with the four screws.

PROPER HAND WASHING TECHNIQUE

1. Wet hands and apply liquid soap.

2. Rub hands vigorously together and scrub all surfaces.

3. Continue until the Hand Wash Timer completes a full cycle.
The soap combined with vigorous scrubbing helps
dislodge and remove germs.

4. Rinse thoroughly and dry hands with a clean towel.

PROBLEMS WITH THE TIMER?

If you experience any problem with your Hand Wash Timer,
contact the manufacturer immediately at 877-392-7854 (Toll Free
in the U.S. and Canada) or at 630-784-1000 (outside the U.S and
Canada).

CLEANING THE TIMER

To clean the timer, wipe it lightly using a clean, dry towel. Do
NOT submerse the timer in water. Do NOT wash it in a
dishwasher. This will void the warranty.

remove the back panel.

LIMITED WARRANTY

Equipment manufactured by A.J. Antunes & Co. has been constructed of the finest materials available and manufactured to high quality standards. These units
are warranted to be free from mechanical and electrical defects for a period of one (1) year from date of purchase or 18 months from shipment from factory,
whichever occurs first, under normal use and service, and when installed in accordance with manufacturer’s recommendations. To insure continued proper
operation of the units, follow the maintenance procedures outlined in this document.

1. This warranty does not cover cost of installation, defects caused by improper storage or handling prior to placing of the Equipment. This warranty
does not cover consumable items such as Batteries. This warranty does not cover damage due to misuse, abuse, submersing in water/liquid,
washing in dishwasher, or dropping of the equipment. For warranty consideration, contact Customer Service at 800-253-2991 for a Return Goods
Authorization (RGA) number then ship the unit to the factory at 180 Kehoe Blvd, Carol Stream, IL 60188 (customer is responsible for return shipping and
handling charges). A.J. Antunes & Co. reserves the right to refuse warranty service at any time if it is determined that the unit has been dam-
aged due to misuse, abuse, submersing in water/liquid, washing in dishwasher, or dropping the unit.

2. A.J. Antunes & Co. reserves the right to make changes in design or add any improvements on any product. The right is always reserved to modify equip­ment because of factors beyond our control and government regulations. Changes to update equipment do not constitute a warranty charge.

3. If shipment is damaged in transit, the purchaser should make a claim directly upon the carrier. Careful inspection should be made of the shipment as
soon as it arrives and visible damage should be noted upon the carrier’s receipt. Damage should be reported to the carrier. This damage is not covered
under this warranty.

4. Warranty charges do not include freight or foreign, excise, municipal or other sales or use taxes. All such freight and taxes are the responsibility of the
purchaser.

5. THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, EACH OF WHICH IS HEREBY EXPRESSLY DISCLAIMED. THE
REMEDIES DESCRIBED ABOVE ARE EXCLUSIVE AND IN NO EVENT SHALL A.J. ANTUNES & CO. BE LIABLE FOR SPECIAL CONSEQUENTIAL
OR INCIDENTAL DAMAGES FOR THE BREACH OR DELAY IN PERFORMANCE OF THIS WARRANTY.

6. For warranty claims outside the 50 United States, contact the distributor that sold the unit to you.

P/N 1020263 Rev. F 07/10

A.J. Antunes & Co.

Headquarters/Manufacturing

180 Kehoe Boulevard

Carol Stream, Illinois 60188 USA

Phone [phone]

Toll Free [phone]

Fax: [phone]

www.ajantunes.com

Antunes Equipment

Manufacturing (Suzhou) Ltd.,

9 Hou Ju Road, Building #24,

S&T Park, SND

Suzhou, Jiangsu, China 215011

Phone: [phone]

Fax: [phone]