Antari FLC-20 User Manual
Formula:Fog Liquid Revision: 1.0
Issue Date: Aug. 26, 2013
Page: 1/7
Product Name : Fog Liquid
Trade Name : FLC-4 / FLC-5
Product Type : Stage
Details of the supplier of the material safety data sheet
Manufacturer/Supplier:
Antari Lighting & Effects Ltd.
No.8, Lane 231, Sec. 1, Nankan Rd., Luzhu Township, Taoyuan County 338, Taiwan (R.O.C)
Tel: +886 33225829
Further information obtainable from: Antari Lighting & Effects Ltd.
Emergency telephone number:
Jason Ho
Tel: +886 33225829
Email: jasonho@antari.com.tw
Ratings Key
NPCA/HMIS NFPA 704 0 = minimal
Health: 1 1 1 = slight
Flammability: 0 0 2 = moderate
Reactivity: 0 0 3 = serious
4 = severe
Product description：Compounding
Component CAS No. Concentration
Ethykene Glycol 107-21-1 33.0%
Glycerin(mist) 56-81-5 2.0%
Sodium Dehydroacetic 4418-26-2 2.6-5 PPM
Distilled Water 7732-18-5 65.0%
Note(s): This is not a dangerous substance
MATERIAL SAFETY DATA SHEET
Section 1. PRODUCT AND COMPANY IDENTIFICATION
Section 3. COMPOSITION / INFORMATION ON INGREDIENTS
Section 2. HAZARDS IDENTIFICATION
Hazard Ratings*
Formula:Fog Liquid Revision: 1.0
Issue Date: Aug. 26, 2013
Page: 2/7
Section 4. FIRST AID MEASURES
After inhalation: Supply fresh air; consult doctor in case of complainte.
After skin contact: Immediately wash with water and soap and rinse thoroughly.
If skin irritation continues, consult a doctor.
After eye contact: Rinse opened eye for several minutes under running water.
If symptoms persist, consult a doctor.
After swallowing: if symptoms persist consult doctor.
Suitable extinguishing agents: Use fire fighting measures that suit the environment.
Special hazards arising from the substance or mixture No further relevant information available.
Protectove equipment: Mouth respiratory protective device.
Section 6. ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures
Mount respiratory protective device.
Environmental precautions:
Dilute with plenty of water.
Do not allow to enter sewers / surface or ground water.
Methods and material for containment and cleaning up:
Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust).
Section 7. HANDLING AND STORAGE
Handling:
Precautions for safe handling: Keep receptacles tightly sealed.
Information about protection against explosions and fires: Keep ignition sources away.
Storage:
Requirements to be met by storerooms and receptacles: Store in a cool location.
Information about storage in one common storage facility:
Store away from foodstuffs.
Store away from flammable substances.
Further information about storage conditions: Keep receptacle tightly sealed.
Section 5. FIRE-FIGHTING MEASURES
MATERIAL SAFETY DATA SHEET
Formula:Fog Liquid Revision: 1.0
Issue Date: Aug. 26, 2013
Page: 3/7
Section 8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Additional information about design of technical systems: No further data; see item 7.
Additional information: The lists that were valid during the creation were used as basis.
Based on the composition shown in section 3, the following measures are suggested for occupational
safety measure
Personal protective equipment:
General protective and hygienic measures:
The usual precautionary measures for handling chemicals should be followed.
Breathing equipment: Suitable respiratory protective device recommended.
Protection of hands:
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.
Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/
the chemical mixture.
Selection of the glove material on consideration of the penetration times, rates of diffusion and the
degradation
Material of gloves
The selection of the suitable gloves does not only depend on the material, but also on further marks of
quality and varies from manufacturer to manufacturer. As the product is a preparation of several
substances, the resistance of the glove material can not be calculated in advance and has therefore to be
checked prior to the application.
Penetration time of glove material
The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be
observed.
Eye protection:
Goggles recommended during refilling.
MATERIAL SAFETY DATA SHEET
Loading...