Angel ANGEL 1 User Manual

• This Operator’s and User’s

Manual is in English.

• It contains important safety

guidelines and Instructions.

• Should you be unsure at any

stage, or unable to understand the contents within this manual you must seek expert advice.

• Le mode d’emploi est en

Anglais.

• Il contient des instructions

et mesures de sécurité importantes.

• En cas de doute, ou s’il vous

est impossible de comprendre le contenu du monde d’emploi, demandez conseil à un expert.

• Este manual de (operarios y)

usarios està en Inglés.

• Contiene importantes normas

de seguridad e instrucciones.

• Si no esta seguro de algún

punto o no entiende los contenidos de este manual debe conultar con un experto.

• Diese Bedienungs- und

Benutzeranleitung ist in Englisch.

• Sie enthält wichtige

herheitsrichtlinien und -bestimmungen.

• Sollten Sie sich in irgendeiner

Weise unsicher sein, oder den Inhalt dieses Heftes nicht verstehen, lassen Sie siche bitte von einem Experten beraten.

Contents

General Warnings 2

Switching on your Angel 3

Turning the Angel off 3

Navigation switch 4

Replacing the 9v battery 4

Switching Angel eyes on/off 5

OPTO board 5

Macro line hose 5

Propellant air/nitrogen supply 6

Adjusting the ASA position 6

Installing an air nitrogen system 6

Bolt removal and rotor breech 7

Velocity adjustment 7

OLED menu 8-9

Modes

Semi Auto 10

NPPL 10

PSP 10

MILLENNIUM 10

XBall/NXL 10

CFOA 11

Full Auto 11

Demo 11

Custom Semi 11

Breakout 11

Soft breakout 11

Hard breakout 11

Ramp 12

Parameters

Valve dwell 12

De-Bounce 12

Loader speed delay 13

MROF eyes on/off 13

Breakout 14

Ramp 14

Shot % ﬁltering 14

Anti bolt stick 15

Software version 15

Factory reset 15

Game timer alarm 16

Tournament lock 16

General care and cleaning

Left & right cut-aways 17

General assemblies 18-19

In-line regulator service & assembly 20

Rubber ﬁnger detent 21

Angel eyes servicing 22

Angel eyes removal 23

LPR adjustment 24

LPR assembly removal & replacement 25

LPR spool removal 26

Exhaust valve guide removal 27

Exhaust valve stem removal 27

Ram removal 28

Magnetic force trigger adjustment 29

Front and back stop position adjustment 29

Trigger activation position 30

Wiring connections 30

Fault ﬁnding 31-32

Useful conversions 31

Warranty - EEC/ROW 33-34

Warranty - USA/Canada 35-36

Warranty card 37

ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY INSTRUCTIONS AND GUID ELINES

• The ANGEL is not a toy.

• Careless or improper use, including failure to follow instructions and warnings within this Operator Manual and attached to the ANGEL could cause death or serious injury.

• Do not remove or deface any warnings attached to the ANGEL.

• Paintball industry standard eye/face/ear and head protection designed speciﬁcally to stop paintballs and meeting ASTM standard F1776 (USA) or CE standard (Europe) must be worn by user and any person within range.

• Must be at least 18 years of age to purchase the ANGEL.

• Persons under 18 years of age must have adult supervision when using or handling the ANGEL.

• Observe all local and national laws, regulations and guidelines.

• Use only on professional paintball ﬁelds where codes of safety are strictly enforced.

• Use 0.68 calibre paintballs only.

• Keep the ANGEL switched off until ready to shoot.

• Treat every Angel as if it is loaded.

• Never point the ANGEL at anything you do not intend to shoot.

• Do not shoot at persons at close range.

• Do not shoot at fragile objects such as windows.

• Always measure your Angels velocity before playing paintball, using a suitable chronograph.

• Never shoot at velocities in excess of 300 feet (92 meters) per second, or at velocities greater than local or national laws allow.

• Do not ﬁre the ANGEL with the breech open or without the bolt in the breech, as high pressure gas will be emitted.

• Use compressed air/nitrogen gas only. Do not use CO2.

• Do not exceed 850 psi (58 bar) input pressure.

• Always follow instructions, warnings and guidelines given with any ﬁrst stage regulator you use with the ANGEL.

• Do not ﬁre the ANGEL with the breech release knob in the unlocked position.

• Never look into the barrel or breech area of the ANGEL whilst the Angel is switched on and able to ﬁre.

• Never put your ﬁnger or any foreign objects into the breech or paintball feed tube of the ANGEL

• Never allow pressurised gas to come into contact with any part of your body.

• Always switch off the ANGEL when not in use.

• Always ﬁt a barrel blocking device to your ANGEL when not in use on the ﬁeld of play.

• Always remove all paintballs from the ANGEL when not in use on the ﬁeld of play.

• Always remove the ﬁrst stage regulator and relieve all residual gas pressure from the ANGEL before disassembly.

• The ANGEL can hold a small residual charge of gas, typically 2 shots, with the ﬁrst stage regulator removed. Always discharge the Angel in a safe direction to relieve this residual gas pressure.

• Always remove ﬁrst stage regulator and all residual gas pressure from the ANGEL for transport and storage.

• Always follow warnings and guidelines given with your ﬁrst stage regulator for safe transport and storage.

• Always store the ANGEL in a secure place.

• THIS OPERATOR’S MANUAL MUST ALWAYS ACCOMPANY THE PRODUCT IN THE EVENT OF RESALE OR NEW OWNERSHIP.

• SHOULD YOU BE UNSURE AT ANY STAGE YOU MUST SEEK EXPERT ADVICE.

Switching on your Angel

ADH ERE S TRIC TLY TO T HESE

AND ALL OTHE R SAF ETY

INS TRUCT IONS AND GUIDE LINE S

· Angel is LIVE and capable of ﬁring.

To switch the Angel on press and hold the navigation switch 1 inwards for up to 2 seconds. The Angel will turn on and will automatically go into LIVE mode with the eyes on. The display screen will illuminate and will show the ﬁring Status of the Angel.

The LED on the rear of the grip frame will show blue.

Turning the Angel off

Switch the Angel off by pressing and holding the navigation switch 1 in for 1 second. A goodbye message will be displayed on the screen and the Angel will power down.

Push & hold

for 1 sec

ADH ERE S TRIC TLY TO T HESE

AND ALL OTHE R SAF ETY

INS TRUCT IONS AND GUIDE LINE S

· Ensure a barrel blocking device is ﬁtted to the ANGEL.

· Ensure the hopper is removed from the ANGEL.

· Ensure that there are no paintballs in the ANGEL.

· Paintball industry standard eye/face/ear and head protection designed speciﬁcally to stop paintballs and meeting ASTM standard F1776 (USA) or CE standard (Europe) must be worn by user and any person within range.

· SHOULD YOU BE UNSURE AT ANY STAGE YOU MUST SEEK EXPERT ADVICE.

Gun status

Eyes

status

Ball

status

Game timer status

Screen shows Eyes on

and ball detected

Screen shows Eyes off

and eyes are faulty.

Push & hold

navigation switch for

up to 2 secs

Battery status

Screen shows Eyes off

and no ball present.

Making the Angel SAFE

When you turn the Angel on the Angel is LIVE. To make the Angel SAFE, either:

• Access the menu options by pushing the navigation

upwards and holding for 1.5 sec. This automatically puts the Angel in SAFE.

• Choose SAFE from the menu options.

When the Angel is SAFE a screen similar to that below will show. The screen will indicate the Angel is SAFE. The screen will also indicate the mode you are in and whether the tournament lock is on or off. (See page 16).

Tournament lock status

Mode

Navigation switch

The functions, features and settings of the Angel are controlled by a 3 directional navigation switch

ADH ERE S TRIC TLY TO T HESE

AND ALL OTHE R SAF ETY

INS TRUCT IONS AND GUIDE LINE S

· Ensure a barrel blocking device is ﬁtted to the ANGEL.

· Ensure the hopper is removed from the ANGEL.

· Ensure that there are no paintballs in the ANGEL.

· SHOULD YOU BE UNSURE AT ANY STAGE YOU MUST SEEK EXPERT ADVICE.

located on the rear of the grip frame. The switch can move up and down to scroll through features and settings indicated on the display and can be pressed in to select the highlighted function or setting required.

The navigation switch is located on the rear of the grip frame and allows access to the Angel 1 internal menu option.

Replacing the 9v battery

• Ensure that the Angel is off.

• If required switch the Angel off by pressing and

holding the navigation switch in for 1 second. A goodbye message will be displayed on the screen and the Angel will power down.

• Remove the right hand grip cheek 1 by removing

the 3 screws 2 using a suitable 2mm Allen key.

• If a battery is already present carefully lift the

battery 3 from its housing.

• Observe the battery polarity as marked on the

battery housing terminal and on the battery.

Always use a good quality fresh battery.

Push the switch up or down and hold for 1.5 seconds. To navigate through the options simply push the switch up to scroll up and push the switch down to scroll down. Press the switch inwards to make a selection.

Switching Angel eyes OFF/ON

ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY INSTRUCTIONS AND

· THE ANGEL IS LIVE AND CAPABLE OF DISCHARGING.

• Ensure that the Angel is on (see page 3).

• As default the Angel Eyes will always be ON

whenever the Angel is switched ON.

• The Angel eyes can be switched off by pulling and

holding the trigger 1 for 1 second. The Angel’s MROF will drop to its default MROF eyes off setting. It will ﬁre 1 shot to conﬁrm that the eyes have been switched off and the buzzer will sound once. The eyes off symbol will be displayed on the display screen.

• To turn the Angel eyes back on pull and hold the

trigger 1 again for 2 seconds,. The MROF will return to MROF eyes on setting (see page 15 for factory default setting), the buzzer will sound twice the eyes on symbol will be displayed on the display screen.

• Should the eyes detect a malfunction due to a

component failure or the eyes becoming dirty they will automatically turn themselves off and the MROF will revert to its MROF eyes off setting (see page 15 for factory default setting), the display will indicate that the eyes are off and that a ball is not detected.

GUIDELINES

OPTO board

The Angel incorporates the OPTO board. This board is the latest development in trigger sensing function. It achieves unsurpassed advancements in trigger repeatability and sensitivity, its friction free non mechanical operating switch results in faster shorter and lighter trigger strokes that give the user higher prolonged achievable rates of ﬁre.

Macro line hose

• The Macro line hose may be removed from the

Macro line connectors to facilitate maintenance.

• Pull back the collet 1 on the connector and keep

the collet depressed.

• Pull the Macro line hose 2 out of the connector

ﬁrmly.

• Cut back the Macro line hose cleanly and square 3.

•

Push the hose ﬁrmly into the Macro line connector to re-attach.

Important Note: Please make sure that the macro-line is trimmed back before re-insertion after it has been removed.

ADH ERE S TRIC TLY TO T HESE

AND ALL OTHE R SAF ETY

INS TRUCT IONS AND GUIDE LINE S

· Ensure a barrel blocking device is ﬁtted to the ANGEL.

· Ensure the hopper is removed from the ANGEL.

· Ensure that there are no paintballs in the ANGEL.

· SHOULD YOU BE UNSURE AT ANY STAGE YOU MUST SEEK EXPERT ADVICE.

Push & hold

for 2 secs.

ADH ERE S TRIC TLY TO T HESE

AND ALL OTHE R SAF ETY

INS TRUCT IONS AND GUIDE LINE S

· Always follow instructions, warnings and guidelines given with any ﬁrst stage regulator you use with the ANGEL.

· Use compressed air/nitrogen gas only

DO NOT USE CO2.

· Only use a paintball regulator that has been

designed for air or nitrogen gas.

· Do not exceed 850 psi (58bar) input pressure

to the ANGEL.

· Take suitable precautions when using sharp cutting instruments.

· The Macro Line hose must be cut back cleanly and square prior to attachment or re-attachment to ensure secure ﬁtment.

· SHOULD YOU BE UNSURE AT ANY STAGE YOU

MUST SEEK EXPERT ADVICE.

Propellant air/nitrogen supply Installing an air nitrogen system

The Angel is designed to operate on air/Nitrogen gas. This needs to be supplied to the Angel at an ideal pressure of 400psi (27.5 bar) using a suitable ﬁrst stage regulator.

Adjusting the ASA position on its mounting rail

The ASA connects to the grip frame of the Angel via an integrated dovetail mounting rail 1 that allows the user to slide the ASA body along the rail to ﬁne tune the mounting position of the ASA. The ASA body is locked down onto the rail via two set screws 2 located within a central recess at the front and back of the integrated rail, in order to move the ASA along the rail you need to loosen off the two set screws 2 using a 3mm Allen key, once the desired position of the ASA has been achieved tighten the set screws 2 to lock the ASA into position on the integrated rail.

Each Angel comes complete with a centrally ported on/off Angel ASA allowing for the easy connection of a preset air/nitrogen system for immediate use.

Before installing your pre-set system into the Angel ASA always ensure that the on/off adjuster knob 3 is wound out approximately half way.

Be careful not to unscrew the ASA on/off adjuster knob too far as it is possible to completely disassemble the ASA. If this happens replace the on/off adjuster knob by screwing it back on to the ASA main body in a clock wise motion.

OFF

ASA

assembly

Depression

Pin orientation

Bolt removal and rotor breech

The outer wear surfaces of the Bolt are made from accetal (homopolymer) and the inner core is made from glass re-enforced nylon. This is to ensure – due to its high cycling speeds- the bolt does not seize within the body. Eventually the bolt will show signs of wear but this is dependant on its usage and the environmental conditions.

It is important that the bolt is kept clean and free from dirt or grit and that it is run dry with no lubricant. We recommend that you clean your bolt after each day of use.

Bolt removal is best achieved whilst the angel is gassed up as this ensures that the ram is in the rearward position ready for the bolt to be extracted.

• Ensure that the Angel is off or that it is in safe mode.

• Rotate the breech release knob 1 clockwise until

it stops.

NOTE: The breech block WILL NOT OPEN when the Angel is de-gassed and the ram and bolt are in the forward position. To allow the breech to rotate open, insert a squeegee into the barrel bore and manually push the bolt back.

• Swing out the rotor breach block 2 so that the bolt

is exposed.

• Extract the bolt 3 by pulling it backwards.

• To replace the bolt follow the steps in reverse

order.

Velocity adjustment

Decreasing velocity

The velocity adjusting screw is located on the lower portion of the fore grip 1.

To decrease the velocity, insert a 3mm Allen Key 2 into the velocity adjusting screw and rotate clockwise

Increasing velocity

To increase the velocity insert a 3mm Allen key 2 into the velocity adjusting screw and rotate counter clockwise.

NOTE: When reducing velocity allow at least four shots for the complete system to re calibrate to the new regulated pressure.

Decrease

velocity

Increase

velocity

ADH ERE S TRIC TLY TO T HESE

AND ALL OTHE R SAF ETY

INS TRUCT IONS AND GUIDE LINE S

· Ensure a barrel blocking device is ﬁtted to the ANGEL.

· Ensure the hopper is removed from the ANGEL.

· Ensure that there are no paintballs in the ANGEL.

· Ensure the ANGEL is switched off via the navigation switch on the rear of the grip frame prior to ﬁtting your ﬁrst stage regulator.

· Always follow instructions, warnings and guidelines given with any ﬁrst stage regulator you use with the ANGEL.

· Use compressed air/nitrogen gas only DO NOT USE CO2.

· Only use a paintball regulator that has been designed for air or nitrogen gas.

· Do not exceed 850 psi (58bar) input pressure to the ANGEL.

· Take suitable precautions when using sharp cutting instruments.

· The Macro Line hose must be cut back cleanly and square prior to attachment or reattachment to ensure secure ﬁtment.

· SHOULD YOU BE UNSURE AT ANY STAGE YOU MUST SEEK EXPERT ADVICE.

OLED menu

ADH ERE S TRIC TLY TO T HESE

AND ALL OTHE R SAF ETY

INS TRUCT IONS AND GUIDE LINE S

· Ensure a barrel blocking device is ﬁtted to the ANGEL.

· Ensure the hopper is removed from the ANGEL.

· Ensure that there are no paintballs in the ANGEL.

· SHOULD YOU BE UNSURE AT ANY STAGE YOU MUST SEEK EXPERT ADVICE.

IMPORTANT NOTE

At any point when accessing the OLED menu options - pulling the trigger will return you to the SAFE screen.

Once you have accessed the Status menu the Angel automatically reverts to SAFE

Status The Status menu allows you to select between

Live/Safe, the Information display screen and

the Parameters setting.

• To access the Status menu press and hold the

navigation switch up or down for 1.5 seconds.

• Once in the Status menu using the navigation

switch scroll up or down to choose between

Live/Safe, Information and Parameters.

• Pressing the navigation switch inwards will select

the highlighted function.

Information

The Information screen will display all the relevant information relating to the electronic settings of your Angel.

• With the Angel on and Live push the navigation

switch up or down for 1.5 seconds.

• The Angel will be in the Status menu.

• Use the navigation switch to scroll through

the Status menu settings till Information is highlighted.

• Push the navigation switch inwards to select the

Information menu.

• The following information will be displayed on the

OLED. Scroll up or down using the navigation switch to view this information.

Status

Software version

Mode

Soft break-out setting

Hard break-out setting

Soft ramp setting

Hard ramp setting

Dwell time MROF eyes on limit MROF eyes off limit

De bounce level

Loader speed level

Shot % ﬁltering

Anti Bolt Stick

Angel eyes on/off

Game timer set

Alarm time set

Total shots ﬁred since reset

Battery voltage

Parameters

The Angel’s settings can be easily adjusted from the

Parameters menu.

• With the Angel on and Live push and hold the

navigation switch up or down for 1.5 seconds.

• The Angel will be in the Status menu.

• Use the navigation switch to scroll through the

Status menu settings till Parameters is highlighted.

• Push the navigation switch inwards to select the

Parameters menu.

The following functions are all accessed via the navigation switch and can all be accessed and adjusted from the Parameters display.

Modes

Valve Dwell

De-bounce

Loader speed

MROF eyes ON

MROF eyes OFF

Breakout

Ramp feature

Shot Filter

ABS Game Time Set Alarm Time Set

The navigation switch is located on the rear of the grip frame and allows access to the Angel 1 internal menu option.

OLED Menu

Semi Auto

NPPL

Millennium

XBall/NXL

CFOA

Full Auto

Demo

Custom Semi

Soft Break-out

Break-out

Soft Ramp

Hard Ramp

PSP

STATUS

ParametersLive/Safe Information

Modes

Valve Dwell

De-bounce

Loader speed

MROF eyes ON

MROF eyes OFF

Breakout

Ramp Feature

Shot Filter

ABS

Game Time Set

Alarm Time Set

Current settings

Status

Software version

Mode

Soft break-out setting

Hard break-out setting

Soft ramp setting

Hard ramp setting

Dwell time

MROF eyes on limit

MROF eyes off limit

De-Bounce level

Loader speed level

Shot % ﬁltering

Anti Bolt Stick

Angel eyes on/off

Game timer set

Alarm time set

Total shots ﬁred since reset

Battery voltage

ADH ERE S TRIC TLY TO T HESE

AND ALL OTHE R SAF ETY

INS TRUCT IONS AND GUIDE LINE S

· Ensure a barrel blocking device is ﬁtted to the ANGEL.

· Ensure the hopper is removed from the ANGEL.

· Ensure that there are no paintballs in the ANGEL.

· SHOULD YOU BE UNSURE AT ANY STAGE YOU MUST SEEK EXPERT ADVICE.

IMPORTANT NOTE:

Tournament lock

To comply with some Tournament rules some of the Angel’s features are required to be locked down so that they cannot be adjusted on the ﬁeld of play.

For more details see page 16.

MODES

ADH ERE S TRIC TLY TO T HESE

AND ALL OTHE R SAF ETY

INS TRUCT IONS AND GUIDE LINE S

· Ensure a barrel blocking device is ﬁtted to the ANGEL.

· Ensure the hopper is removed from the ANGEL.

· Ensure that there are no paintballs in the ANGEL.

· SHOULD YOU BE UNSURE AT ANY STAGE YOU MUST SEEK EXPERT ADVICE.

MODE OPTIONS Page

Semi Auto 10 NPPL 10 PSP 10 Millennium 10 XBall/NXL 10 CFOA 11 Full Auto 11 Demo 11 Custom Semi 11 Break-out 11 Soft Break-out 11 Hard Break-out 11 Ramp 12

Modes

• Ensure that the Angel is switched on.

• Ensure that you are not activating the trigger.

• Push and hold the navigation switch UP or DOWN

for 1.5 seconds.

• The Status menu will be displayed.

• Push the navigation button up to highlight the

iParameters menu.

• Push the navigation switch in to select the

Parameters menu.

• From the Parameters menu select the iMode

feature by pushing the navigation switch inward.

• Scroll up or down through the Mode options by

pushing the navigation switch up or down.

• Once the desired Mode setting has been reached

press the navigation switch inwards to save the new setting.

• A Saved Mode message will be displayed.

The Parameters menu will be displayed.

Semi Auto

The Angel eyes will default to on whenever the Angel is made live via the navigation switch.

With the eyes activated the Angel will only ﬁre when a paintball is present and has been detected by the Angel eyes.

With the eyes activated the MROF that the Angel will ﬁre at is limited by the MROF eyes on level.

With the eyes turned off the MROF that the Angel will ﬁre at is limited by the MROF eyes off level.

The Angel will ﬁre 1 shot for each pull of the trigger.

Break-out and Ramp settings do not function in this Mode.

NPPL

The Angel eyes will default to on whenever the Angel is made live via the navigation switch.

With the eyes activated the Angel will only ﬁre when a paintball is present and has been detected by the Angel eyes.

With the eyes activated the MROF that the Angel will ﬁre at is limited by the MROF eyes on level.

With the eyes turned off the MROF that the Angel will ﬁre at is limited by the MROF eyes off level.

The Angel will ﬁre 1 shot for each pull of the trigger.

Break-out and Ramp settings do not function in this Mode.

PSP

The Angel eyes will default to on whenever the Angel is made live via the navigation switch.

With the eyes activated the Angel will only ﬁre when a paintball is present and has been detected by the Angel eyes.

The ﬁrst 3 shots will be ﬁred in semi automatic.

On the 4th shot the Angel will ramp to a pre set MROF set at 15.4 balls per second, provided that the user maintains trigger pulls at a rate of or above 5 balls per second.

If the user stops ﬁring for more than 1 second the initial 3 shots in semi automatic must be re initiated.

Millennium

The Angel eyes will default to on whenever the Angel is made live via the navigation switch.

With the eyes activated the Angel will only ﬁre when a paintball is present and has been detected by the Angel eyes.

The rate of ﬁre will be capped at 15 shots per sec.

Ramping of shots is allowed once 8 BPS is achieved the Angel may ramp up to 15 BPS only if 8 BPS or greater is maintained. Once the trigger is released only 1 additional shot may be discharged.

Additional break-out and ramp settings do not function in this Mode.

X-Ball/NXL

The Angel eyes will default to on whenever the Angel is made live via the navigation switch.

With the eyes activated the Angel will only ﬁre when a paintball is present and has been detected by the Angel eyes.

The ﬁrst 3 shots will be ﬁred in semi automatic.

On the 4th shot if the trigger is pulled and held the Angel will ﬁre fully automatic up to a pre set maximum MROF set at 15.4 balls per second.

The Angel will stop ﬁring as soon as the trigger is released.

If the user stops ﬁring for more than 1 second the initial 3 shots in semi automatic must be re initiated.

CFOA

The Angel eyes will default to on whenever the Angel is made live via the navigation switch.

With the eyes activated the Angel will only ﬁre when a paintball is present and has been detected by the Angel eyes.

The ﬁrst 3 shots will be ﬁred in semi automatic.

On the 4th shot the Angel will ramp to a pre set MROF set at 15.4 balls per second, provided that the user maintains trigger pulls at a rate at or above 5 balls per second.

If the user stops ﬁring for more than 1 second the initial 3 shots in semi automatic must be re initiated.

Full Auto

The Angel eyes will default to on whenever the Angel is made live via the navigation switch.

With the eyes activated the Angel will only ﬁre when a paintball is present and has been detected by the Angel eyes.

The Angel will ﬁre at a capped maximum rate of 15 balls per second with the Angel eyes activated.

With the angel eyes deactivated the Angel will ﬁre at a capped maximum rate of 15 balls per second.

It is possible to lower the MROF with both eyes on and eyes off in this mode but you will not be permitted to raise them above the 15 bps cap.

Demo

This is a dry ﬁring mode for ﬁring the Angel when on display and is designed to demonstrate the rate of ﬁre achievable. It should only be used for demonstration purposes, as the Angel eyes feature is reverse functioned so that it can not ﬁre should a paintball be detected.

MODES

Custom Semi

The Angel eyes will default to on whenever the Angel is made live via the navigation switch.

With the eyes activated the Angel will only ﬁre when a paintball is present and has been detected by the Angel eyes.

With the eyes activated the MROF that the Angel will ﬁre at is limited by the MROF eyes on level.

With the eyes turned off the MROF that the Angel will ﬁre at is limited by the MROF eyes off level.

The Angel will ﬁre 1 shot for each pull of the trigger.

Break-out and Ramp settings can be used individually or in combination in this Mode.

Break-out

There are 2 break-out modes that can only be used when the Angel is in custom semi mode.

Soft break out

Once the soft break out feature has been selected from the custom modes screen and the Angel is on and live it will ﬁre as if it were in normal semi auto mode until the break-out mode is activated. To activate the break-out feature press the navigation switch inwards, the alarm will momentarily sound to indicate that the break-out mode has been initiated. In order for the Angel to start ﬁring in the break-out mode once it has been initiated a rate of trigger pulls higher than 4 per second must be reached and maintained within the time period that the break-out mode is active. The duration of the time period that the break-out mode is active can be adjusted. The range for this adjustment is 1 – 20 seconds. If the rate of trigger pulls at any point once the break-out mode has been initiated fall below 4 per second or should the trigger be pulled and held in for 2 seconds or the time period of the break-out elapses the breakout mode will revert to the previously selected mode.

Hard break-out

Once the hard break out feature has been selected from the custom modes screen and the Angel is on and live it will ﬁre as if it were in normal semi auto mode until the break-out mode is activated.

ADH ERE S TRIC TLY TO T HESE

AND ALL OTHE R SAF ETY

INS TRUCT IONS AND GUIDE LINE S

· Ensure a barrel blocking device is ﬁtted to the ANGEL.

· Ensure the hopper is removed from the ANGEL.

· Ensure that there are no paintballs in the ANGEL.

· SHOULD YOU BE UNSURE AT ANY STAGE YOU MUST SEEK EXPERT ADVICE.

+ 25 hidden pages