Analog Devices AD9223, AD9221, AD9220 Datasheet

Complete 12-Bit 1.5/3.0/10.0 MSPS

a

FEATURES
Monolithic 12-Bit A/D Converter Product Family
Family Members Are: AD9221, AD9223, and AD9220
Flexible Sampling Rates: 1.5 MSPS, 3.0 MSPS and

10.0 MSPS
Low Power Dissipation: 59 mW, 100 mW and 250 mW
Single +5 V Supply
Integral Nonlinearity Error: 0.5 LSB
Differential Nonlinearity Error: 0.3 LSB
Input Referred Noise: 0.09 LSB
Complete: On-Chip Sample-and-Hold Amplifier and

Voltage Reference
Signal-to-Noise and Distortion Ratio: 70 dB
Spurious-Free Dynamic Range: 86 dB
Out-of-Range Indicator
Straight Binary Output Data
28-Lead SOIC and 28-Lead SSOP

PRODUCT DESCRIPTION

The AD9221, AD9223, and AD9220 are a generation of high
performance, single supply 12-bit analog-to-digital converters.
Each device exhibits true 12-bit linearity and temperature drift
performance
AD9221/AD9223/AD9220 share the same interface options,
package, and pinout. Thus, the product family provides an
upward or downward component selection path based on per­formance, sample rate and power. The devices differ with re­spect to their specified sampling rate and power consumption
which is reflected in their dynamic performance over frequency.

The AD9221/AD9223/AD9220 combine a low cost, high speed
CMOS process and a novel architecture to achieve the resolution
and speed of existing hybrid and monolithic implementations at
a fraction of the power consumption and cost. Each device is a
complete, monolithic ADC with an on-chip, high performance,
low noise sample-and-hold amplifier and programmable voltage
reference. An external reference can also be chosen to suit the dc
accuracy and temperature drift requirements of the application.
The devices use a multistage differential pipelined architecture with
digital output error correction logic to provide 12-bit accuracy at
the specified data rates and to guarantee no missing codes over the
full operating temperature range.

The input of the AD9221/AD9223/AD9220 is highly flexible,
allowing for easy interfacing to imaging, communications, medi­cal, and data-acquisition systems. A truly differential input
structure allows for both single-ended and differential input
interfaces of varying input spans. The sample-and-hold (SHA)
amplifier is equally suited for both multiplexed systems that
switch full-scale voltage levels in successive channels as well as
sampling single-channel inputs at frequencies up to and beyond
the Nyquist rate. Also, the AD9221/AD9223/AD9220 is well

REV. D

Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.

1

as well as 11.5 bit or better ac performance.2 The

Monolithic A/D Converters

AD9221/AD9223/AD9220

FUNCTIONAL BLOCK DIAGRAM

CLK

SHA

VINA
VINB

CAPT
CAPB

VREF

SENSE

MODE

SELECT

MDAC1

GAIN = 16

5

5

REFCOM

MDAC2

GAIN = 8

4

A/DA/D

4

DIGITAL CORRECTION LOGIC

OUTPUT BUFFERS

1V

AD9221/AD9223/AD9220

suited for communication systems employing Direct-IF Down
Conversion since the SHA in the differential input mode can
achieve excellent dynamic performance far beyond its specified
Nyquist frequency.

2

A single clock input is used to control all internal conversion
cycles. The digital output data is presented in straight binary
output format. An out-of-range (OTR) signal indicates an
overflow condition which can be used with the most significant
bit to determine low or high overflow.

PRODUCT HIGHLIGHTS

The AD9221/AD9223/AD9220 family offers a complete single­chip sampling 12-bit, analog-to-digital conversion function in
pin-compatible 28-lead SOIC and SSOP packages.

Flexible Sampling Rates—The AD9221, AD9223 and AD9220
offer sampling rates of 1.5 MSPS, 3.0 MSPS and 10.0 MSPS,
respectively.

Low Power and Single Supply—The AD9221, AD9223 and
AD9220 consume only 59 mW, 100 mW and 250 mW, respec­tively, on a single +5 V power supply.

Excellent DC Performance Over Temperature—The AD9221/
AD9223/AD9220 provide 12-bit linearity and temperature drift
performance.

1

Excellent AC Performance and Low Noise—The AD9221/
AD9223/AD9220 provides better than 11.3 ENOB performance
and has an input referred noise of 0.09 LSB rms.

Flexible Analog Input Range—The versatile onboard sample­and-hold (SHA) can be configured for either single ended or differ­ential inputs of varying input spans.

NOTES

1

Excluding internal voltage reference.

2

Depends on the analog input configuration.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone] World Wide Web Site: http://www.analog.com
Fax: [phone] © Analog Devices, Inc., 2000

DVDDAVDD

MDAC3

GAIN = 4

3

A/D

3

12

DVSSAVSS

CML

A/D

3

OTR
BIT 1

(MSB)
BIT 12

(LSB)

2

AD9221/AD9223/AD9220–SPECIFICATIONS

(AVDD = +5 V, DVDD = +5 V, f

DC SPECIFICATIONS

otherwise noted)

Parameter AD9221 AD9223 AD9220 Units

RESOLUTION 12 12 12 Bits min

MAX CONVERSION RATE 1.5 3 10 MHz min

INPUT REFERRED NOISE (TYP)

V

= 1 V 0.23 0.23 0.23 LSB rms typ

REF

V

= 2.5 V 0.09 0.09 0.09 LSB rms typ

REF

ACCURACY

Integral Nonlinearity (INL) ±0.4 ±0.5 ±0.5 LSB typ

±1.25 ±1.25 ±1.25 LSB max

Differential Nonlinearity (DNL) ±0.3 ±0.3 ±0.3 LSB typ

±0.75 ±0.75 ±0.75 LSB max
±0.6 ±0.6 ±0.7 LSB typ
±0.3 ±0.3 ±0.35 LSB typ

INL
DNL

1

1

No Missing Codes 12 12 12 Bits Guaranteed

Zero Error (@ +25°C) ±0.3 ±0.3 ±0.3 % FSR max
Gain Error (@ +25°C)
Gain Error (@ +25°C)

2

3

±1.5 ±1.5 ±1.5 % FSR max
±0.75 ±0.75 ±0.75 % FSR max

TEMPERATURE DRIFT

Zero Error ±2 ±2 ±2 ppm/°C typ

Gain Error
Gain Error

2

3

±26 ±26 ±26 ppm/°C typ
±0.4 ±0.4 ±0.4 ppm/°C typ

POWER SUPPLY REJECTION

AVDD, DVDD

(+5 V ± 0.25 V) ±0.06 ±0.06 ±0.06 % FSR max

ANALOG INPUT

Input Span (with V

Input Span (with V

= 1.0 V) 2 2 2 V p-p min

REF

= 2.5 V) 5 5 5 V p-p max

REF

Input (VINA or VINB) Range 0 0 0 V min

AVDD AVDD AVDD V max

Input Capacitance 16 16 16 pF typ

INTERNAL VOLTAGE REFERENCE

Output Voltage (1 V Mode) 1 1 1 Volts typ

Output Voltage Tolerance (1 V Mode) ±14 ±14 ±14 mV max

Output Voltage (2.5 V Mode) 2.5 2.5 2.5 Volts typ

Output Voltage Tolerance (2.5 V Mode) ±35 ±35 ±35 mV max

Load Regulation

4

2.0 2.0 2.0 mV max

REFERENCE INPUT RESISTANCE 5 5 5 kΩ typ

POWER SUPPLIES

Supply Voltages

AVDD +5 +5 +5 V (±5% AVDD
DVDD +2.7 to +5.25 +2.7 to +5.25 +5 (±5%) V

Supply Current

IAVDD 14.0 26 58 mA max

11.8 20 48 mA typ

IDVDD 0.5 0.5 12 mA max

0.02 0.02 10 mA typ

POWER CONSUMPTION 59.0 100 250 mW typ

70.0 130 310 mW max

NOTES

1

V

=1 V.

REF

2

Including internal reference.

3

Excluding internal reference.

4

Load regulation with 1 mA load current (in addition to that required by the AD9220/AD9221/AD9223).

Specification subject to change without notice.

= Max Conversion Rate, V

SAMPLE

= 2.5 V, VINB = 2.5 V, T

REF

MIN

to T

unless

MAX

Operating)

REV. D–2–

AD9221/AD9223/AD9220

AC SPECIFICATIONS

(AVDD = +5 V, DVDD= +5 V, f
Ended Input T

MIN

to T

unless otherwise noted)

MAX

= Max Conversion Rate, V

SAMPLE

= 1.0 V, VINB = 2.5 V, DC Coupled/Single-

REF

Parameters AD9221 AD9223 AD9220 Units

MAX CONVERSION RATE 1.5 3.0 10.0 MHz min

DYNAMIC PERFORMANCE

Input Test Frequency 1 (VINA = –0.5 dBFS) 100 500 1000 kHz

Signal-to-Noise and Distortion (SINAD) 70.0 70.0 70 dB typ

69.0 68.5 68.5 dB min

Effective Number of Bits (ENOBs) 11.3 11.3 11.3 dB typ

11.2 11.1 11.1 dB min

Signal-to-Noise Ratio (SNR) 70.2 70.0 70.2 dB typ

69.0 68.5 69.0 dB min

Total Harmonic Distortion (THD) –83.4 –83.4 –83.7 dB typ

–77.5 –76.0 –76.0 dB max

Spurious Free Dynamic Range (SFDR) 86.0 87.5 88.0 dB typ

79.0 77.5 77.5 dB max

Input Test Frequency 2 (VINA = –0.5 dBFS) 0.50 1.50 5.0 MHz

Signal-to-Noise and Distortion (SINAD) 69.9 69.4 67.0 dB typ

69.0 68.0 65.0 dB min

Effective Number of Bits (ENOBs) 11.3 11.2 10.8 dB typ

11.2 11.1 10.5 dB min

Signal-to-Noise Ratio (SNR) 70.1 69.7 68.8 dB typ

69.0 68.5 67.5 dB min

Total Harmonic Distortion (THD) –83.4 –82.9 –72.0 dB typ

–77.5 –75.0 –68.0 dB max

Spurious Free Dynamic Range (SFDR) 86.0 85.7 75.0 dB typ

79.0 76.0 69.0 dB max
Full Power Bandwidth 25 40 60 MHz typ
Small Signal Bandwidth 25 40 60 MHz typ
Aperture Delay 1 1 1 ns typ
Aperture Jitter 4 4 4 ps rms typ
Acquisition to Full-Scale Step 125 43 30 ns typ

Specifications subject to change without notice.

DIGITAL SPECIFICATIONS

(AVDD = +5 V, DVDD = +5 V, T

MIN

to T

unless otherwise noted)

MAX

Parameters Symbol Units

CLOCK INPUT

High Level Input Voltage V
Low Level Input Voltage V
High Level Input Current (V
Low Level Input Current (V

= DVDD) I

IN

= 0 V) I

IN

Input Capacitance C

IH

IL

IH

IL

IN

+3.5 V min
+1.0 V max

±10 µA max
±10 µA max

5 pF typ

LOGIC OUTPUTS

DVDD = 5 V

High Level Output Voltage (I
High Level Output Voltage (I
Low Level Output Voltage (I
Low Level Output Voltage (I

= 50 µA) V

OH

= 0.5 mA) V

OH

= 1.6 mA) V

OL

= 50 µA) V

OL

OH

OH

OL

OL

+4.5 V min
+2.4 V min
+0.4 V max
+0.1 V max

DVDD = 3 V

High Level Output Voltage (I
High Level Output Voltage (I
Low Level Output Voltage (I
Low Level Output Voltage (I

= 50 µA) V

OH

= 0.5 mA) V

OH

= 1.6 mA) V

OL

= 50 µA) V

OL

Output Capacitance C

Specifications subject to change without notice.

REV. D

OH

OH

OL

OL

OUT

–3–

+2.95 V min
+2.80 V min
+0.4 V max
+0.05 V max
5 pF typ

AD9221/AD9223/AD9220

WARNING!

ESD SENSITIVE DEVICE

SWITCHING SPECIFICATIONS

(T

to T

MIN

with AVDD = +5 V, DVDD = +5 V, CL = 20 pF)

MAX

Parameters Symbol AD9221 AD9223 AD9220 Units

Clock Period
CLOCK Pulsewidth High t
CLOCK Pulsewidth Low t
Output Delay t

1

t

C

CH

CL

OD

667 333 100 ns min
300 150 45 ns min
300 150 45 ns min
8 8 8 ns min
13 13 13 ns typ
19 19 19 ns max

Pipeline Delay (Latency) 3 3 3 Clock Cycles

NOTES

1

The clock period may be extended to 1 ms without degradation in specified performance @ +25 °C.

Specifications subject to change without notice.

ANALOG

INPUT

INPUT

CLOCK

DATA

OUTPUT

S1

t

CH

S2

t

C

t

CL

S3

S4

t

OD

DATA 1

Figure 1. Timing Diagram

ABSOLUTE MAXIMUM RATINGS*

With
Respect

Parameter to Min Max Units

AVDD AVSS –0.3 +6.5 V
DVDD DVSS –0.3 +6.5 V
AVSS DVSS –0.3 +0.3 V
AVDD DVDD –6.5 +6.5 V
REFCOM AVSS –0.3 +0.3 V
CLK AVSS –0.3 AVDD
Digital Outputs DVSS –0.3 DVDD
VINA, VINB AVSS –0.3 AVDD
VREF AVSS –0.3 AVDD
SENSE AVSS –0.3 AVDD
CAPB, CAPT AVSS –0.3 AVDD

+ 0.3 V

+ 0.3 V
+ 0.3 V
+ 0.3 V
+ 0.3 V
+ 0.3 V

Junction Temperature +150 °C
Storage Temperature –65 +150 °C

Lead Temperature

(10 sec) +300 °C

*Stresses above those listed under Absolute Maximum Ratings may cause perma-

nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum
ratings for extended periods may effect device reliability.

THERMAL CHARACTERISTICS

Thermal Resistance
28-Lead SOIC

= 71.4°C/W

θ

JA

= 23°C/W

θ

JC

28-Lead SSOP

= 63.3°C/W

θ

JA

= 23°C/W

θ

JC

ORDERING GUIDE

Temperature Package Package

Model Range Description Options

AD9221AR –40°C to +85°C 28-Lead SOIC R-28
AD9223AR –40°C to +85°C 28-Lead SOIC R-28
AD9220AR –40°C to +85°C 28-Lead SOIC R-28
AD9221ARS –40°C to +85°C 28-Lead SSOP RS-28
AD9223ARS –40°C to +85°C 28-Lead SSOP RS-28
AD9220ARS –40°C to +85°C 28-Lead SSOP RS-28

AD9220/AD9221/AD9223SOICEB Evaluation Board
AD9220/AD9221/AD9223SSOPEB Evaluation Board

CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although these devices feature proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.

–4–

REV. D

AD9221/AD9223/AD9220

PIN CONNECTIONS

CLK

(LSB) BIT 12

BIT 11
BIT 10

BIT 9
BIT 8
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2

(MSB) BIT 1

OTR

1
2
3
4

AD9221/

5

AD9223/

6

AD9220

7

TOP VIEW

(Not to Scale)

8

9
10
11
12
13
14

28
27
26
25
24
23
22
21
20
19
18
17
16
15

DVDD
DVSS
AVDD
AVSS
VINB
VINA
CML
CAPT
CAPB
REFCOM
VREF
SENSE
AVSS
AVDD

PIN FUNCTION DESCRIPTIONS

Pin
Number Name Description

1 CLK Clock Input Pin
2 BIT 12 Least Significant Data Bit (LSB)
3–12 BIT N Data Output Bit
13 BIT 1 Most Significant Data Bit (MSB)
14 OTR Out of Range
15, 26 AVDD +5 V Analog Supply
16, 25 AVSS Analog Ground
17 SENSE Reference Select
18 VREF Reference I/O
19 REFCOM Reference Common
20 CAPB Noise Reduction Pin
21 CAPT Noise Reduction Pin
22 CML Common-Mode Level (Midsupply)
23 VINA Analog Input Pin (+)
24 VINB Analog Input Pin (–)
27 DVSS Digital Ground
28 DVDD +3 V to +5 V Digital Supply

DEFINITIONS OF SPECIFICATION

INTEGRAL NONLINEARITY (INL)

INL refers to the deviation of each individual code from a line
drawn from “negative full scale” through “positive full scale.”
The point used as “negative full scale” occurs 1/2 LSB before
the first code transition. “Positive full scale” is defined as a
level 1 1/2 LSB beyond the last code transition. The deviation
is measured from the middle of each particular code to the true
straight line.

DIFFERENTIAL NONLINEARITY (DNL, NO MISSING
CODES)

An ideal ADC exhibits code transitions that are exactly 1 LSB
apart. DNL is the deviation from this ideal value. Guaranteed
no missing codes to 12-bit resolution indicates that all 4096
codes, respectively, must be present over all operating ranges.

ZERO ERROR

The major carry transition should occur for an analog value
1/2 LSB below VINA = VINB. Zero error is defined as the
deviation of the actual transition from that point.

GAIN ERROR

The first code transition should occur at an analog value
1/2 LSB above negative full scale. The last transition should
occur at an analog value 1 1/2 LSB below the nominal full
scale. Gain error is the deviation of the actual difference
between first and last code transitions and the ideal differ­ence between first and last code transitions.

TEMPERATURE DRIFT

The temperature drift for zero error and gain error specifies the

maximum change from the initial (+25°C) value to the value at

or T

T

MIN

MAX

.

POWER SUPPLY REJECTION

The specification shows the maximum change in full scale from
the value with the supply at the minimum limit to the value
with the supply at its maximum limit.

APERTURE JITTER

Aperture jitter is the variation in aperture delay for successive
samples and is manifested as noise on the input to the A/D.

APERTURE DELAY

Aperture delay is a measure of the sample-and-hold amplifier
(SHA) performance and is measured from the rising edge of the
clock input to when the input signal is held for conversion.

SIGNAL-TO-NOISE AND DISTORTION (S/N+D, SINAD)
RATIO

S/N+D is the ratio of the rms value of the measured input sig­nal to the rms sum of all other spectral components below the
Nyquist frequency, including harmonics but excluding dc.
The value for S/N+D is expressed in decibels.

EFFECTIVE NUMBER OF BITS (ENOB)

For a sine wave, SINAD can be expressed in terms of the num­ber of bits. Using the following formula,

N = (SINAD – 1.76)/6.02

it is possible to get a measure of performance expressed as N,
the effective number of bits.

Thus, effective number of bits for a device for sine wave inputs
at a given input frequency can be calculated directly from its
measured SINAD.

TOTAL HARMONIC DISTORTION (THD)

THD is the ratio of the rms sum of the first six harmonic
components to the rms value of the measured input signal and
is expressed as a percentage or in decibels.

SIGNAL-TO-NOISE RATIO (SNR)

SNR is the ratio of the rms value of the measured input signal
to the rms sum of all other spectral components below the
Nyquist frequency, excluding the first six harmonics and dc.
The value for SNR is expressed in decibels.

SPURIOUS FREE DYNAMIC RANGE (SFDR)

SFDR is the difference in dB between the rms amplitude of the
input signal and the peak spurious signal.

REV. D

–5–

AD9221/AD9223/AD9220

AD9221–Typical Characterization Curves

1.0

0.8

0.6

0.4

0.2

0.0

–0.2

DNL – LSBs

–0.4

–0.6
–0.8
–1.0

0 4095

CODE

Figure 2. Typical DNL

80

75

70

65

60

55

SINAD – dB

50

45
40

0.1 1.0

–0.5dB

–6.0dB

–20.0dB

FREQUENCY – MHz

1.0

0.8

0.6

0.4

0.2

0.0

–0.2

INL – LSBs

–0.4
–0.6
–0.8
–1.0

0 4095

Figure 3. Typical INL

–50
–55
–60

–20.0dB

–65
–70

–6.0dB

–75

THD – dB

–80
–85

–100

–0.5dB

–90
–95

0.1 1.0
FREQUENCY – MHz

(AVDD = +5 V, DVDD = +5 V, f

CODE

= 1.5 MSPS, TA = +25ⴗC)

SAMPLE

8,180,388

HITS

121,764

N–1 N N+1

CODE

85,895

Figure 4. “Grounded-Input”
Histogram (Input Span = 2 V p-p)

80

75

–0.5dB

70

65

–6.0dB

60

55

SINAD – dB

–20.0dB

50

45
40

0.1 1.0
FREQUENCY – MHz

Figure 5. SINAD vs. Input Frequency
(Input Span = 2.0 V p-p, V

–50

–55

–60

–65

–70

THD– dB

–75

–80

–85
–90

0.1 1.0
FREQUENCY – MHz

= 2.5 V)

CM

–20.0dB

–0.5dB

–6.0dB

Figure 8. THD vs. Input Frequency
(Input Span = 5.0 V p-p, V

= 2.5 V)

CM

Figure 6. THD vs. Input Frequency
(Input Span = 2.0 V p-p, V

–60

–65

–70

–75

–80

THD – dB

–85

–90

–95

–100

0.2 1 2

0.4 0.6
SAMPLE RATE – MSPS

= 2.5 V)

CM

5V p-p

2V p-p

Figure 9. THD vs. Sample Rate
(A

= –0.5 dB, fIN = 500 kHz,

IN

V

= 2.5 V)

CM

Figure 7. SINAD vs. Input Frequency
(Input Span = 5.0 V p-p, V

100

90

80

70
60

50

SNR/SFDR – dB

40
30
20

30.3 0.8

10

–60 –50 –30–40

SFDR

SNR

AIN – dBFS

= 2.5 V)

CM

–20 –10

0

Figure 10. SNR/SFDR vs. AIN (Input
Amplitude) (f
= 2 V p-p, V

= 500 kHz, Input Span

IN

= 2.5 V)

CM

–6–

REV. D

AD9221/AD9223/AD9220

CODE

HITS

96,830

8,123,672

130,323

N–1 N N+1

FREQUENCY – MHz

SINAD – dB

80

75

40

0.1 1.0 10.0

70

65

45

60

55

50

–0.5dB

–6.0dB

–20.0dB

AIN – dBFS

100

90

30

–60 –40

0

–20

70

60

40

50

80

SNR/SFDR – dB

20
10

–50 –30 –10

SFDR

SNR

AD9223–Typical Characterization Curves

1.0

0.8

0.6

0.4

0.2

0.0

–0.2

DNL – LSBs

–0.4
–0.6
–0.8
–1.0

0 4095

CODE

Figure 11. Typical DNL

80

75

70

65

60

55

SINAD – dB

50

45
40

0.1 1.0 10.0
FREQUENCY – MHz

–0.5dB

–6.0dB

–20.0dB

1.0

0.8

0.6

0.4

0.2

0.0

–0.2

INL – LSBs

–0.4
–0.6
–0.8
–1.0

0 4095

0

Figure 12. Typical INL

–50
–55

–60
–65
–70
–75

THD – dB

–80
–85
–90
–95

–100

0.1 1.0

(AVDD = +5 V, DVDD = +5 V, f

CODE

–20.0dB

–0.5dB

–6.0dB

FREQUENCY – MHz

10.0

= 3.0 MSPS, TA = +25ⴗC)

SAMPLE

Figure 13. “Grounded-Input”
Histogram (Input Span = 2 V p-p)

Figure 14. SINAD vs. Input Frequency
(Input Span = 2.0 V p-p, V

–50
–55

–60
–65

–20.0dB

–70
–75

–6.0dB

THD – dB

–80

–0.5dB

–85
–90
–95

–100

0.1 1.0 10.0
FREQUENCY – MHz

Figure 17. THD vs. Input Frequency
(Input Span = 5.0 V p-p, V

REV. D

Figure 15. THD vs. Input Frequency

= 2.5 V)

CM

(Input Span = 2.0 V p-p, V

–60

–65

–70

–75

–80

THD – dB

–85

–90

–95

–100

0.6 1 2 3 5 6

0.4 0.8 4
SAMPLE RATE – MSPS

= 2.5 V)

CM

5V p-p

2V p-p

Figure 18. THD vs. Sample Rate (A

= 2.5 V)

CM

= –0.5 dB, fIN = 500 kHz, VCM = 2.5 V)

–7–

Figure 16. SINAD vs. Input Frequency
(Input Span = 5.0 V p-p, V

IN

Figure 19. SNR/SFDR vs. AIN (Input
Amplitude)
Span = 2 V p-p, V

= 1.5 MHz, Input

(fIN

= 2.5 V)

CM

= 2.5 V)

CM

AD9221/AD9223/AD9220

FREQUENCY – MHz

SINAD – dB

80

75

40

0.1 1.0 10.0

70

65

45

60

55

50

–6.0dB

–0.5dB

–20.0dB

AIN – dBFS

90

80

20

–60 –40

0

–20

60

50

30

40

70

SNR/SFDR – dB

10

–50 –30 –10

SFDR

SNR

AD9220–Typical Characterization Curves

1.0

0.8

0.6

0.4

0.2

0.0

–0.2

DNL – LSBs

–0.4

–0.6
–0.8
–1.0

1 4095

CODE

Figure 20. Typical DNL

80

75

70

65

60

55

SINAD – dB

50

45

40

0.1 1.0

–0.5dB

–6dB

–20dB

FREQUENCY – MHz

10.0

1.0

0.8

0.6

0.4

0.2

0.0

–0.2

INL – LSBs

–0.4
–0.6
–0.8
–1.0

1 4095

Figure 21. Typical INL

–50
–55
–60
–65
–70
–75

THD – dB

–80
–85
–90
–95

–100

0.5 1.0 10.0
FREQUENCY – MHz

(AVDD = +5 V, DVDD = +5 V, f

CODE

–20dB

–6dB

–0.5dB

= 10 MSPS, TA = +25ⴗC)

SAMPLE

8,123,672

HITS

134,613

N–1 N N+1

CODE

130,323

Figure 22. “Grounded-Input”
Histogram (Input Span = 2 V p-p)

Figure 23. SINAD vs. Input Fre­quency (Input Span = 2.0 V p-p,
V

= 2.5 V)

CM

–50

–55

–60

–65

–70

THD – dB

–75

–80

–85
–90

0.1 1.0 10.0

Figure 26. THD vs. Input Frequency
(Input Span = 5.0 V p-p, V

–20.0dB

–0.5dB

FREQUENCY – MHz

–6.0dB

CM

= 2.5 V)

Figure 24. THD vs. Input Frequency
(Input Span = 2.0 V p-p, V

–60

–65

–70

–75

–80

THD – dB

–85

–90

–95

–100

5V p-p

2V p-p

110

SAMPLE RATE – MSPS

= 2.5 V)

CM

15

Figure 27. THD vs. Clock Frequency
(A

= –0.5 dB, fIN = 1.0 MHz, VCM =

IN

2.5 V)

–8–

Figure 25. SINAD vs. Input Fre­quency (Input Span = 5.0 V p-p,
V

= 2.5 V)

CM

Figure 28. SNR/SFDR vs. AIN (Input
Amplitude) (f
Span = 2 V p-p, V

= 5.0 MHz, Input

IN

= 2.5 V)

CM

REV. D

AD9221/AD9223/AD9220

SETTLING TIME – ns

CODE

4000

3000

0

0

6010 20 30 40 50

2000

1000

AD9220

AD9223

AD9221

INTRODUCTION

The AD9221/AD9223/AD9220 are members of a high perfor­mance, complete single-supply 12-bit ADC product family based
on the same CMOS pipelined architecture. The product family
allows the system designer an upward or downward component
selection path based on dynamic performance, sample rate, and
power. The analog input range of the AD9221/AD9223/AD9220
is highly flexible allowing for both single-ended or differential
inputs of varying amplitudes which can be ac or dc coupled.
Each device shares the same interface options, pinout and pack­age offering.

The AD9221/AD9223/AD9220 utilize a four-stage pipeline
architecture with a wideband input sample-and-hold amplifier
(SHA) implemented on a cost-effective CMOS process. Each
stage of the pipeline, excluding the last stage, consists of a low
resolution flash A/D connected to a switched capacitor DAC
and interstage residue amplifier (MDAC). The residue amplifier
amplifies the difference between the reconstructed DAC output
and the flash input for the next stage in the pipeline. One bit of
redundancy is used in each of the stages to facilitate digital
correction of flash errors. The last stage simply consists of a
flash A/D.

The pipeline architecture allows a greater throughput rate at the
expense of pipeline delay or latency. This means that while the
converter is capable of capturing a new input sample every clock
cycle, it actually takes three clock cycles for the conversion to be
fully processed and appear at the output. This latency is not a
concern in most applications. The digital output, together with
the out-of-range indicator (OTR), is latched into an output
buffer to drive the output pins. The output drivers of the
AD9220ARS, AD9221 and AD9223 can be configured to
interface with +5 V or +3.3 V logic families, while the AD9220AR
can only be configured for +5 V logic.

The AD9221/AD9223/AD9220 use both edges of the clock in
their internal timing circuitry (see Figure 1 and specification
page for exact timing requirements). The A/D samples the ana­log input on the rising edge of the clock input. During the clock
low time (between the falling edge and rising edge of the clock),
the input SHA is in the sample mode; during the clock high
time it is in hold. System disturbances just prior to the rising
edge of the clock and/or excessive clock jitter may cause the
input SHA to acquire the wrong value, and should be minimized.

The internal circuitry of both the input SHA and individual
pipeline stages of each member of the product family are opti­mized for both power dissipation and performance. An inherent
tradeoff exists between the input SHA’s dynamic performance
and its power dissipation. Figures 29 and 30 shows this tradeoff
by comparing the full-power bandwidth and settling time of the
AD9221/AD9223/AD9220. Both figures reveal that higher
full-power bandwidths and faster settling times are achieved at
the expense of an increase in power dissipation. Similarly, a
tradeoff exists between the sampling rate and the power dissipated
in each stage.

As previously stated, the AD9220, AD9221 and AD9223 are
similar in most aspects except for the specified sampling rate,
power consumption, and dynamic performance. The product
family is highly flexible providing several different input ranges

and interface options. As a result, many of the application issues
and tradeoffs associated with these resulting configurations are
also similar. The data sheet is structured such that the designer
can make an informed decision in selecting the proper A/D and
optimizing its performance to fit the specific application.

0

AD9220

–3

–6

AMPLITUDE – dB

–9

–12

1 10010

FREQUENCY – MHz

AD9223

AD9221

Figure 29. Full-Power Bandwidth

Figure 30. Settling Time

ANALOG INPUT AND REFERENCE OVERVIEW

Figure 31, a simplified model of the AD9221/AD9223/AD9220,
highlights the relationship between the analog inputs, VINA,
VINB, and the reference voltage, VREF. Like the voltage
applied to the top of the resistor ladder in a flash A/D converter,
the value VREF defines the maximum input voltage to the A/D
core. The minimum input voltage to the A/D core is automatically
defined to be –VREF.

AD9221/AD9223/AD9220

VINA

V

CORE

VINB

+V

REF

A/D

CORE

–V

REF

12

Figure 31. AD9221/AD9223/AD9220 Equivalent Functional
Input Circuit

REV. D

–9–