Amped wireless RTA2200T User Manual

SETUP GUIDE

v022717

READ FIRST

GOT QUESTIONS?

Phone: 888-573-8820 or 909-217-3168 Email: techsupport@ampedwireless.com Web: www.ampedwireless.com/support

HELIOS

HIGH POWER

Watch the Installation Video here: http://support.ampedwireless.com/rta2200t

Disconnect & Power Off your Existing Router

(if available)

Disconnect your existing router from your computer, your broadband modem, and a power outlet. If you do not have an existing router please continue to Step 2.

Power Off your Modem

Power off the modem by disconnecting the modem’s power adapter from the power outlet. If your modem has a backup battery, remove the backup battery from your modem.

Do NOT power on your modem until Step 4.

AC2200 TRI-BAND WI-FI

ROUTER

RTA2200T

Modem

Existing Router

Remove

Backup Battery

Modem

Connect the Router to your Modem

Use the included Ethernet cable and connect one end of the cable to your modem.

Connect the other end of the cable to the blue

Modem

port on the Router.

Do NOT connect the power adapter to the Router at this time.

Modem

Router

Power On your Modem

Plug in the power adapter and reinsert the backup battery (if available) to power on the modem.

Allow a minute or two for the modem to initiate.

Attach Antennas, Power On & Connect to the Router

Reinsert

Backup Battery

Modem

Open your Web Browser

Amped Wireless

http://setup.ampedwireless.com

Recommended browsers: Google Chrome, Safari or

Internet Explorer (8.0 and up). Do not use Firefox.

ACCESSING THE WEB MENU DOES NOT REQUIRE INTERNET ACCESS. THE MENU IS SERVED FROM THE ROUTER.

- or -

Attach the antennas to the Router.

Attach the Power Adapter to the Router’s

PWR

port and a power outlet.

Connect your tablet, smart phone or PC to the Router's Wi-Fi network: Amped_Helios Security key: wireless

- or Connect an Ethernet cable between your PC and a green wired port on the back of the Router.

Enter the setup web address into your browser:

(see back for detailed instructions)

http://setup.ampedwireless.com

If the URL fails to open, then try: http://192.168.3.1

If you have problems accessing the web menu...

Disable third-party ﬁrewalls, such as North, ZoneAlarm, or Windows Defender.

Disconnect from all wireless networks and use a wired connection to the Router. Try again.

Welcome to the Setup Wizard

If this is your ﬁrst time setting up the Router, the Setup Wizard should automatically load.

Click Begin Setup to continue.

If you wish to manually conﬁgure your Router, you can skip the Setup Wizard.

If the Dashboard loads, scroll to the bottom and click the Setup Wizard button to access the wizard.

Setup screens for mobile devices will vary from desktop and tablet versions.

Double check that the modem is connected to the Router's Modem port.

Check that your antennas are all attached ﬁrmly to the antenna connectors.

Click Next to continue.

Internet Connection Detection

The Wizard will try to detect your Internet settings and conﬁgure the Router. Please be patient.

If there is a problem with your Internet connection or if your Internet provider requires that you log in before accessing the Internet, a prompt will appear notifying you of the issue.

Once your Wizard has conﬁgured your Internet settings, you should see a green check mark.

Click Next to continue.

Personalize your Wi-Fi Settings

The default ID of your 5GHz Wi-Fi network and

2.4GHz Wi-Fi network is: Amped_Helios_5.0_1,

Amped_Helios_5.0_2 or Amped_Helios_2.4

Enter a new name in the SSID ﬁeld. Users connecting wirelessly to the Router will use these IDs to identify your Wi-Fi networks.

The default Security Key of your Wi-Fi networks is:

wireless

Enter a new key for both the 5GHz and 2.4GHz Wi-Fi

networks in the Security Key ﬁeld. The keys must be at least 8 characters long.

Create a Password for your Router

This password is NOT your Wi-Fi connection password. This password is to access the web menu of the Router to access additional router settings. Leave this blank if you do not wish to have a password. However, we recommend creating a password at this time for security purposes.

Click Apply to save your settings. The Router will reboot. This process may take up to 1 minute. The page will automatically reload after the countdown. If it does not, you may need to refresh the page manually or check your connection to the Router.

Setup Summary

Congratulations, the Router is now successfully conﬁgured and your settings are now saved. You may now connect additional devices directly to the 4 wired ports on the back panel or connect wirelessly to the Router.

The wizard will notify you if there is a newer ﬁrmware for the Router. We recommend that you upgrade your Router at this time if an update is available.

F R E E T E C H N I C A L S U P P O R T

Dashboard

GOT QUESTIONS?

Phone: 888-573-8820 or 909-217-3168 Email: techsupport@ampedwireless.com Web: www.ampedwireless.com/support

Once you have completed the Setup Wizard, you will now see the Dashboard when you access http://setup.ampedwireless.com. You will not see the Setup Wizard again. Through the Dashboard you can further adjust settings and access the features of the Router. Here you will ﬁnd features like Guest Networks, User Access Controls, Wi-Fi Coverage Controls, Parental Controls and many other features.

v022717

This is the second page of the Setup Guide. Start on the opposite side ﬁrst.

How to Connect Wirelessly to the Router

Windows 10

Access the taskbar on the bottom right of your screen, tap on the Wi-Fi icon, enable Wi-Fi, and select

Amped_Helios_5.0_1, Amped_Helios_5.0_2 or

Amped_Helios_2.4.

Amped_Helios...

Network01

Network02

Mac OS X

Click on the Wireless icon to see available wireless networks. Select Amped_Helios_5.0_1,

Amped_Helios_5.0_2 or Amped_Helios_2.4.

Windows 8

Swipe in from the right edge to access the charms bar, tap on Settings, select the Wi-Fi icon, and select

Amped_Helios_5.0_1, Amped_Helios_5.0_2 or

Amped_Helios_2.4.

Amped_Helios...

iPhone

Tap on your Settings icon, select Wi-Fi, and choose the network, Amped_Helios_5.0_1,

Amped_Helios_5.0_2 or Amped_Helios_2.4.

Amped_Helios...

iPad Tablet

Tap the "Home" button to get to the home page.

Tap the "Settings" app icon.

Tap on Wi-Fi to enter the iPad’s Wi-Fi settings.

Toggle the Wi-Fi "On/Off" selector switch to "On".

Under "Choose a Network," select: Amped_Helios_5.0_1,

E .

Amped_Helios_5.0_2 or Amped_Helios_2.4

Android Tablet

Tap the "Apps" menu on the tablet screen.

Locate and tap the "Settings" app icon.

Under "Wireless & networks," tap "Wi-Fi settings".

Tap the Wi-Fi box to turn on Wi-Fi and scan.

Under "Wi-Fi networks," select: Amped_Helios_5.0_1,

Amped_Helios_5.0_2 or Amped_Helios_2.4

Amped_Helios...

Wi-Fi Protected Setup (One-Touch Setup or Push Button Conﬁguration)

If your Wi-Fi device has WPS one-touch setup, you can use it to connect to the Router:

Hold down the WPS button on the Router (back panel) for 3 seconds. The Power LED will begin to blink.

As it blinks, push the WPS button on your wireless adapter or enable WPS with the provided software for your

wireless adapter. WPS will automatically conﬁgure the connection settings for your wireless adapter to connect to the Router.

Using the Features on the Router

The Router is equipped with many powerful security features which can be accessed through the web menu on the left side under Smart Features, Firewall Settings and Quality of Service:

12:26

Wireless Access Scheduling

Control when your Wi-Fi is on/off

Location: 2.4 or 5GHz Wi-Fi Settings > Access Schedule

User Access Control (MAC/IP)

Restrict network access to speciﬁc users

Location: Smart Features > User Access

Wireless Coverage Control

Adjust the distance of your wireless network

Location: 2.4 or 5GHz Wi-Fi Settings > Wireless Coverage

Block Websites

wwwwww

Prevent access to speciﬁc websites

Location: Smart Features > Block Websites

Firewall Settings

Protect your network from outside intruders

Location: Firewall Settings

Quality of Service (Prioritize Bandwidth)

Manage your network bandwidth

Web Menu (Left Side)

Location: Quality of Service

If you are unfamiliar or want more information on how to set up Smart Features, Firewall Settings, or Quality of Service, please refer to the User’s Guide at http://support.ampedwireless.com/rta2200t

LED Indicator Information

Power:

WPS:

Internet Connection:

5.0GHz Wireless Activity:

2.4GHz Wireless Activity:

Indicates when the Router is powered on. The LED will remain on.

Blinks when Wi-Fi Protected Setup (WPS) is activated and the Router awaits a connection.

Indicates when the Router is connected to a broadband modem. The LED will blink rapidly when Internet trafﬁc is transmitted or received.

Blinks rapidly when data trafﬁc is transmitted or received over the 5GHz wireless network.

Blinks rapidly when data trafﬁc is transmitted or received over the 2.4GHz wireless network.

Additional Router Features

Reset the Router to Default Settings

There are two options to reset the Router back to factory default settings:

Access the Reset button through the web menu on the left side under

More Settings > Management > Save/Reload Settings. Select the Reset Settings to Default.

Access the physical Reset button on the back panel of the Router:

Hold down the Reset button for ﬁve to ten (5-10) seconds. You may need to use a pen tip or pin to access the button. Pressing the Reset Button for less than ﬁve (5) seconds will simply reboot the Router while saving your existing settings.

Share USB Storage Devices

Connect a USB storage device to the USB 3.0 port.

Log onto the web menu at http://setup.ampedwireless.com and

click the USB Storage tab.

Follow instructions for conﬁguring settings to share USB storage device.

Power & LED Lights On/Off

• Power On/Off: Push button to quickly turn the Router on or off.

• LED Lights On/Off: Push button to turn the LED indicators on

the front of the Router on or off.

Reset

Button

Wired Ports

USB 3.0

Storage Port

LED Lights On/Off

Power On/Off

Wired Port LEDs

• Indicates when a device is connected to a wired port (modem or local network) on the back of

the Router. The LED will blink rapidly when wired data trafﬁc is transmitted or received. The green LEDs display when there is an active gigabit connection.

Troubleshooting Tips

PROBLEM:

SOLUTIONS:

PROBLEM:

I entered setup.ampedwireless.com and it failed to open the Web Menu.

a. Make sure your computer is connected to the Router using the included Ethernet cable. Ensure that the power on the Router is on. b. Check that your computer IS NOT connected to any wireless networks. If it is, disable your Wi-Fi connection and disconnect from all wireless networks. Reboot the Router and try again. c. Close your current web browser and reopen it. Use Google Chrome, Internet Explorer (8.0 and up), or Safari. d. Open your web browser and enter 192.168.3.1 into the web address bar. e. Reset the Router to default settings by holding the Reset button (located on the back panel) for ten (10) seconds

and try again. The Setup Wizard should appear. To access the Dashboard, complete or skip the Setup Wizard. The Setup Wizard appears only when the Router has not yet been conﬁgured.

f. If you still cannot access the menu, disconnect the Ethernet cable and connect wirelessly to the Router. Open

your web browser to setup.ampedwireless.com.

g. If the Setup Wizard appears instead of the Dashboard, the Router has not yet been conﬁgured. Complete the

Setup Wizard or skip the Setup Wizard to access the Dashboard.

The Setup Wizard could not automatically conﬁgure my Internet connection.

SOLUTIONS:

a. Reset your modem by holding down the Reset button located on the back of the modem for approximately ten (10) seconds. Try again. b. Reboot the Router by unplugging the power adapter and plugging it back in. c. Static IP: Your Internet connection may require a static IP setting. Check with your ISP to obtain the IP settings. d. DSL Connection: Your Internet connection may require login information. If you are using PPPoE mode, you will need to manually conﬁgure your Internet connection settings and obtain your username and password. e. Cable Modem: Your Internet connection may require you to clone your MAC address. Go to More Settings > IP Settings > Internet Network (WAN) and select Automatic/Dynamic (DHCP) from the dropdown menu. Clone your PC’s MAC address under the DNS settings.

If you continue to have issues setting up the Router, give us a call — we’re here to help: 888-573-8820 or 909-217-3168

Visit our website for more support information and answers to frequently asked questions: www.ampedwireless.com/support

Amped Wireless A Division of Newo Corporation Copyright © 2017 Amped Wireless / Newo Corporation. All rights reserved. Amped Wireless, Newo Corporation, the Amped Wireless Logo are registered trademarks or trademarks of Newo Corporation.

Amped wireless RTA2200T User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual