Amped wireless RTA1900 User Manual

v072115

SETUP GUIDE

READ FIRST

GOT QUESTIONS?

Phone: [phone] or 909-217-3168
Email: [e-mail]
Web: www.ampedwireless.com/support

TITAN

HIGHPOWER

1

2

3

Disconnect & Power Off your Existing Router

(if available)

Disconnect your existing router from your computer, your
broadband modem, and a power outlet. If you do not have
an existing router please continue to Step 2.

Power Off your Modem

Power off the modem by disconnecting the modem’s power
adapter from the power outlet. If your modem has a backup
battery, remove the backup battery from your modem.

Do NOT power on your modem until Step 4.

Connect the Router to your Modem

TM

AC1900 WI-FI

®

ROUTER

Modem

RTA1900

Existing Router

Remove

Backup Battery

Modem

4

5

a

Use the included Ethernet cable and connect
one end of the cable to your modem.

a

Connect the other end of the cable to the blue

b

Modem

port on the Router.

Modem

Router

Power On your Modem

Plug in the power adapter and reinsert the backup battery
(if available) to power on the modem.

Allow a minute or two for the modem to initiate.

b

Do NOT connect the power adapter to the
Router at this time.

Reinsert

Backup Battery

Attach Antennas, Power On & Connect to your Computer

Modem

6

a

b

Open your Web Browser

NOTE: IF YOU HAVE PROBLEMS ACCESSING THE WEB MENU

a

Attach the antennas to the antenna connectors
on the Router.

b

c

- or -

Attach the Power Adapter to the Router’s

PWR

port and a power outlet.

c

Connect to the Router's Wi-Fi network:

Amped_Titan_5.0 or Amped_Titan_2.4

Security key: wireless

- or ­Connect an Ethernet cable between your PC and
a green wired port on the back of the Router.

Enter the setup web address into your browser:

(see back for detailed instructions)

http://setup.ampedwireless.com

If the URL fails to open, then try: http://192.168.3.1

IF YOU HAVE PROBLEMS ACCESSING THE WEB MENU...

Disable third-party firewalls such as Norton, ZoneAlarm or Windows Defender.

Disconnect from all wireless networks and use a wired connection to the Router. Try again.

Accessing the setup menu does not require Internet access. The menu is served from the Router.

7

Welcome to the Setup Wizard

If this is your first time setting up the Router, the
Setup Wizard should automatically load.

Double check that the modem is connected to
the Router's Modem port.

Check that your antennas are all attached firmly
to the antenna connectors.

Click Next to continue.

8

If the Dashboard loads, scroll to the bottom and
click the Setup Wizard button to access the wizard.

If you wish to manually configure your Router you
can also choose to skip the Setup Wizard.

Internet Connection Detection

The Wizard will try to detect your Internet settings
and configure the Router. Please be patient.

If there is a problem with your Internet connection
or if your Internet provider requires that you log in
before accessing the Internet, a prompt will appear
notifying you of the issue.

9

Once your Wizard has configured your Internet
settings, you should see a green check mark.
Click Next to continue.

Personalize your Wi-Fi Settings

The default ID of your 5GHz Wi-Fi network and

2.4GHz Wi-Fi network is: Amped_Titan_5.0 or

Amped_Titan_2.4

To change it, enter a new name in the SSID field. Users
connecting wirelessly to the Router will use these IDs to
identify your Wi-Fi networks.

The default Security Key of your Wi-Fi networks
is: wireless

To change them, enter a new key for both the 5GHz

and 2.4GHz Wi-Fi networks in the Security Key field.
The keys must be at least 8 characters long.

10

Create a Password for your Router

This password is NOT your Wi-Fi connection pass­word. This password is to access the web menu
of the Router to access additional router settings.
Leave this blank if you do not wish to have a
password.

Click Apply to save your settings. The Router will
reboot. This process may take up to 1 minute. The
page will automatically reload after the countdown.
If it does not, you may need to refresh the page
manually or check your connection to the Router.

Setup Summary

Congratulations, the Router is now successfully
configured and your settings are now saved. You
may now connect additional devices directly to the
4 wired ports on the back panel or connect wire­lessly to the Router.

Dashboard

The wizard will notify you if there is a newer firmware
for the Router. We recommend that you upgrade
your Router at this time if an update is available.

GOT QUESTIONS?

?

Phone: [phone] or 909-217-3168
Email: [e-mail]
Web: www.ampedwireless.com/support

Once you have completed the Setup Wizard, you
will now see the Dashboard when you access
http://setup.ampedwireless.com. You will not see
the Setup Wizard again. Through the Dashboard
you can further adjust settings and access the
features of the Router. Here you will find features like
Guest Networks, User Access Controls, Wi-Fi
Coverage Controls, Parental Controls and many
other features.

v070615

This is the second page of the Setup Guide. Start on the opposite side first.

How to Connect Wirelessly to the Router

Windows 7 & Vista

Click on the Wireless icon to see available wireless
networks (For Vista, click Start > Connect To). Select

Amped_Titan_2.4 or Amped_Titan_5.0 network

and click Connect. When prompted for a password,
enter "wireless".

Wireless Network

Wireless Network

Amped_Titan_5.0

Mac OS X

Click on the Wireless icon to see available wireless
networks. Select Amped_Titan_2.4 or

Amped_Titan_5.0 network. When prompted for

a password, enter "wireless".

Windows 8

Swipe in from the right edge to access the charms
bar, tap on Settings, select the Wi-Fi icon, and select

Amped_Titan_2.4 or Amped_Titan_5.0. When prompted

for a password, enter "wireless".

Amped_Titan...

iPhone

Tap on your Settings icon, select Wi-Fi, and choose
the network, Amped_Titan_2.4 or Amped_Titan_5.0.

When prompted for a password, enter "wireless".

Amped_Titan_5.0

Amped_Titan...

iPad Tablet

Tap the "Home" button to get to the home page.

A.

Tap the "Settings" app icon.

B.

Tap on Wi-Fi to enter the iPad’s Wi-Fi settings.

C.

Toggle the Wi-Fi "On/Off" selector switch to "On".

D.

Under "Choose a Network," select:

E .

Amped_Titan_2.4 or Amped_Titan_5.0

When prompted, enter the wireless security key:

F .

"wireless"

Amped_Titan_5.0

Android Tablet

Tap the "Apps" menu on the tablet screen.

A.

Locate and tap the "Settings" app icon.

B.

Under "Wireless & networks," tap "Wi-Fi settings".

C.

Tap the Wi-Fi box to turn on Wi-Fi and scan.

D.

Under "Wi-Fi networks," select:

E.

Amped_Titan_2.4 or Amped_Titan_5.0

When prompted, enter the Password key: "wireless"

F .

Amped_RTA1750_5.0

Amped_Titan_5.0

Wi-Fi Protected Setup (One-Touch Setup or Push Button Configuration)

If your Wi-Fi device has WPS one-touch setup, you can use it to connect to the Router:

Hold down the WPS button on the Router (back panel) for 3 seconds. The Power LED will begin to blink.

A.

As it blinks, push the WPS button on your wireless adapter or enable WPS with the provided software for your

B.

wireless adapter. WPS will automatically configure the connection settings for your wireless adapter to connect
to the Router.

Setting a Login & Password

This login/password is NOT the wireless network key used to connect to your wireless network.

It is strongly recommended that you change these settings and select your
own personal login and password. The Password menu can be accessed
through the web menu under More Settings > Management > Password on
the left side of the web menu. If you forget your login and password, you
will need to reset the Router back to default settings. View the instructions
below on how to reset your Router back to default settings.

Using the Features on the Router

The Router is equipped with many powerful security features which can be accessed through the web
menu on the left side under Smart Features, Firewall Settings and Quality of Service:

12:26

wwwwww

Wireless Access Scheduling

Control when your Wi-Fi is on/off

Location: 2.4 or 5GHz Wi-Fi Settings > Access Schedule

User Access Control (MAC/IP)

Restrict network access to specific users

Location: Smart Features > User Access

Wireless Coverage Control

Adjust the distance of your wireless network

Location: 2.4 or 5GHz Wi-Fi Settings > Wireless Coverage

Block Websites

Prevent access to specific websites

Location: Smart Features > Block Websites

Firewall Settings

Protect your network from outside intruders

Location: Firewall Settings

Web Menu (Left Side)

Quality of Service (Prioritize Bandwidth)

Manage your network bandwidth

Location: Quality of Service

If you are unfamiliar or want more information on how to set up Smart Features, Firewall Settings, or Quality
of Service, please refer to the User’s Guide on the included CD.

LED Indicator Information

Power:

WPS:

5.0GHz Wireless Activity:

2.4GHz Wireless Activity:

Internet Connection:

USB Connection:

Indicates when the Router is powered on. The LED will remain on.

Blinks when Wi-Fi Protected Setup (WPS) is activated and the Router awaits a connection.

Blinks rapidly when data traffic is transmitted or received over the 5GHz wireless network.

Blinks rapidly when data traffic is transmitted or received over the 2.4GHz wireless network.

Indicates when the Router is connected to a broadband modem.
The LED will blink rapidly when Internet traffic is transmitted or received.

Indicates when a USB storage device is connected to the USB 2.0 and/or the USB 3.0 port.

a

b

Additional Router Features

Reset the Router to Default Settings

There are two options to reset the Router back to factory default settings:

Access the Reset button through the web menu on the left side under

1

More Settings > Management > Save/Reload Settings. Select the Reset
Settings to Default.

Access the physical Reset button on the back panel of the Router:

2

Hold down the Reset button for five to ten (5-10) seconds. You may
need to use a pen tip or pin to access the button. Pressing the Reset
Button for less than five (5) seconds will simply reboot the Router while
saving your existing settings.

Share USB Storage Devices

Connect a USB storage device to the USB 2.0 and/or the USB 3.0 port.

1

Log onto the web menu at http://setup.ampedwireless.com and

2

click the USB Storage tab.

3

Follow the instructions for configuring the settings to share the USB storage device.

Power On/Off

USB 2.0

Storage Port

Wired Ports

b

USB 3.0

Storage Port

c

b

d

c

Power & LED Lights On/Off

• Power On/Off: Push button to quickly turn the Router on or off.

• LED Lights On/Off: Push button to turn the LED indicators on

the front of the Router on or off.

LED Lights On/Off

Reset Button

Wired Port LEDs

• Indicates when a device is connected to a wired port (modem or local network) on the back of

the Router. The LED will blink rapidly when wired data traffic is transmitted or received. The green
LEDs display when there is an active gigabit connection.

Troubleshooting Tips

PROBLEM:

SOLUTIONS:

I entered setup.ampedwireless.com and it failed to open the Web Menu.

a. Make sure your computer is connected to the Router using the included Ethernet cable.
Ensure that the power on the Router is on.
b. Check that your computer IS NOT connected to any wireless networks. If it is, disable your Wi-Fi connection
and disconnect from all wireless networks. Reboot the Router and try again.
c. Close your current web browser and reopen it. Use Google Chrome, Internet Explorer (8.0 and up), or Safari.
d. Open your web browser and enter 192.168.3.1 into the web address bar.
e. Reset the Router to default settings by holding the Reset Button (located on the back panel) for ten (10) seconds

and try again. The Setup Wizard should appear. To access the Dashboard, complete or skip the Setup Wizard.
The Setup Wizard appears only when the Router has not yet been configured.

f. If you still cannot access the menu, disconnect the Ethernet cable and connect wirelessly to the Router. Open

your web browser to setup.ampedwireless.com.

g. If the Setup Wizard appears instead of the Dashboard, the Router has not yet been configured. Complete the

Setup Wizard or skip the Setup Wizard to access the Dashboard.

c

a

PROBLEM:

SOLUTION:

If you continue to have issues setting up the Router, give us a call — we’re here to help: 888-573-8820 or 909-217-3168

Visit our website for more support information and answers to frequently asked questions: www.ampedwireless.com/support

Amped Wireless
A Division of Newo Corporation
Copyright © 2015 Amped Wireless / Newo Corporation. All rights reserved.
Amped Wireless, Newo Corporation, the Amped Wireless Logo are registered trademarks or trademarks of Newo Corporation.

The Setup Wizard could not automatically configure my Internet connection.

a. Reset your modem by holding down the Reset button located on the back of the modem for approximately
ten (10) seconds. Try again.
b. Reboot the Router by unplugging the power adapter and plugging it back in.
c. Static IP: Your Internet connection may require a static IP setting. Check with your ISP to obtain the IP settings.
d. DSL Connection: Your Internet connection may require login information. If you are using PPPoE mode,
you will need to manually configure your Internet connection settings and obtain your username and password.
e. Cable Modem: Your Internet connection may require you to clone your MAC address. Go to More Settings >
IP Settings > Internet Network (WAN) and select Automatic/Dynamic (DHCP) from the dropdown menu.
Clone your PC’s MAC address under the DNS settings.