Amped wireless B1200EX User Manual

v040617

SETUP GUIDE

READ FIRST

GOT QUESTION S?

Phone: [phone] or 909-217-3168
Email: [e-mail]
Web: www.ampedwireless.com/support

AC1200 PLUG-IN WI-FI® RANGE EXTENDER

Watch the Installation Video here: http://support.ampedwireless.com/b1200ex

Find a Setup Location About Half-Way Between your

1

Wi-Fi Router & your Wireless Dead Zone

RECOMMENDED

SIGNAL STRENGTH

>70%

Internet

Wi-Fi Router

B1200EX

Wi-Fi Range Extender

Dead Zone

Home/Office Network

THE RANGE EXTENDER MUST RECEIVE A STRONG SIGNAL FROM YOUR WI-FI ROUTER.

We recommend the signal from your router is >70%. We'll find out the exact strength in Step 6.

If you are connecting to a dual band router, both 2.4GHz and 5GHz connections should be greater than 70%.

Connect your PC or Tablet to the Range Extender

2

Plug the Range Extender into

a

b

Amped_B1200EX_2.4

Amped_B1200EX_5.0

Attention Windows Users:

A prompt may appear asking: "Do you want to set up your network?"
If so, select "Connect to the network without setting it up"
or "No, just connect".

a

a power outlet.

Connect to the Range Extender's

b

Wi-Fi network: Amped_B1200EX_2.4
or Amped_B1200EX_5.0.

- or -

Open your Web Browser

3

Amped Wireless

http://setup.ampedwireless.com

Recommended browsers: Google Chrome, Safari or Internet Explorer (8.0 and up). Do not use Firefox.

ACCESSING THE WEB MENU DOES NOT REQUIRE INTERNET ACCESS. THE MENU IS SERVED FROM THE RANGE EXTENDER.

Enter the setup web address into your browser:

http://setup.ampedwireless.com

If the URL fails to open, then try: http://192.168.1.240

IF YOU HAVE PROBLEMS ACCESSING THE WEB MENU...

a

a) Disconnect your PC from all Wi-Fi networks.

b

b) Attach an Ethernet cable (not included) between the PC and the Range Extender.

c

c) Open your web browser and go to http://setup.ampedwireless.com again.

Welcome to the Setup Wizard

4

Scan for a Home Network to Extend

5

The Setup Wizard will guide you through the
setup process.

Click Scan to find available networks to extend.

Setup screens for mobile devices will vary from desktop and
tablet versions.

Highlight and select the wireless network(s)
that you wish to repeat. If you have a dual band
router, select BOTH the 2.4GHz and 5GHz network
names.

Recommended Signal

>70%

If you see your wireless network listed below 70% or
not at all, you need to move the Range Extender closer
to the router and scan again. A poor signal could
result in slower speeds or dropped connections.

Select the wireless network with a signal
strength greater than 70% for the most
reliable connection.

Click Next to continue.

Home Network Security Settings (if necessary)

6

If your wireless home network(s) has security
enabled, you will need to enter the security key here.
If you selected both a 2.4GHz and a 5GHz network
to repeat, you will need to enter both security keys
here.

If your wireless home network(s) does not have
security enabled, leave the security field blank.

Click Next to continue.

Configure Settings for your Extended Networks

7

The IDs of your Extended Networks are:

Amped_B1200EX_2.4 and Amped_B1200EX_5.0

If you choose to "Clone" the settings from your
Home Network, the wizard will copy the SSID and
security key of your Home Network.

The SSID of the Extended Network will have a
"_RE" at the end of its name. For example:
Home_Network_RE

You can also manually enter a new network ID and
security key. The new security key must be at least
8 characters long.

Click Next to apply the settings.

Connect to the New Extended Network

8

During the countdown process, the Range Extender
will reboot and disconnect the Wi-Fi connection.
At this point, you will need to reconnect your PC or
tablet to the new Extended Network. You may
connect to either the 2.4GHz or 5GHz Extended
Network. Follow the instructions on the screen to
connect. Once you have connected, click OK to
complete the setup process.

DO NOT LEAVE OR REFRESH THIS PAGE

Allow the countdown to complete and the wizard will
automatically redirect you to the next step.

Setup Summary

9

If there are problems with your configuration, the setup
wizard will inform you to rescan for a network to extend.

If there are no problems, you will see the Setup Summary
page below.

Congratulations, the Range Extender is now
successfully configured. Your settings are now
saved. You may also attach any wired network
devices to the wired port on the bottom of the
Range Extender.

The wizard will notify you if there is a newer firmware for
the Extender. We recommend that you upgrade your
Extender at this time if an update is available.

If you experience any problems during this process,
please contact Amped Wireless Elite Support:

Phone: [phone]
Email: [e-mail]
Web: www.ampedwireless.com/support

If you haven’t already positioned your Range Extender in an optimal location, you may do so now.

All Range Extender settings are saved and can be safely powered off for relocation.

Finding an Optimal Placement Location (Signal Strength LED)

The Range Extender is equipped with a Signal Strength LED on the front of the
device to help you find the most optimal location. After setup, the LED can be your
guide for positioning the Extender to a better location (if needed). It may take 1-3
minutes for the LED to register after powering on the Extender. For optimal
performance, we recommend a signal strength of at least 70%.

Solid Green: Excellent Signal 65-100%

Blinking Green: Moderate Signal 64% and below

No Light: No Connection

Note: The LED will not turn on if the Extender is not connected to a Home Network.

v041317

This is the second page of the Setup Guide. Start on the opposite side first.

How to Connect to the Range Extender

Connecting to the 5GHz network requires that you have a 5GHz capable network adapter.

Windows 10

Access the taskbar on the bottom right of your
screen, tap on the Wi-Fi icon, enable Wi-Fi, and select

Amped_B1200EX_2.4 or Amped_B1200EX_5.0.

Amped_B1200EX

Network01

Network02

Mac OS X

Click on the Wireless icon to see available wireless
networks. Select the Amped_B1200EX_2.4 or

Amped_B1200EX_5.0 network.

Amped_B1200EX

Windows 8

Swipe in from the right edge to access the charms
bar, tap on Settings, select the Wi-Fi icon, and select
the Amped_B1200EX_2.4 or Amped_B1200EX_5.0.

Amped_B1200EX

iPhone

Tap on your Settings icon, select Wi-Fi, and choose
the Amped_B1200EX_2.4 or Amped_B1200EX_5.0
network.

Amped_B1200EX

iPad Tablet

A. Press the "Home" button to get to the homepage.
B. Tap the "Settings" app icon.
C. Tap on Wi-Fi to enter the iPad’s Wi-Fi settings.
D. Toggle the Wi-Fi "On/Off" selector switch to "On".
E. Under "Choose a Network...", select:
Amped_B1200EX_2.4 or Amped_B1200EX_5.0.

Amped_B1200EX

Android Tablet

A. Tap the "Apps" menu on the tablet screen.
B. Locate and tap the "Settings" app icon.
C. Under "Wireless & networks," tap "Wi-Fi settings".
D. Tap the Wi-Fi box to turn on Wi-Fi and scan.
E. Under "Wi-Fi networks", select:
Amped_B1200EX_2.4 or Amped_B1200EX_5.0.

Amped_B1200EX

Using the Features on your Range Extender

The Range Extender is equipped with many powerful features like BoostBand™ Technology and
advanced security features, all of which can be accessed through the web menu:

Technology

Increase the overall speed and performance of your extended
network by streamlining dual band network traffic through a single
Wi-Fi frequency band between the Router and the Range Extender.

Menu Location: More Settings > BoostBand Technology

12:26

Wireless Access Scheduling

Control when your Wi-Fi is on/off.

Menu Location: More Settings > 2.4 or 5GHz Wi-Fi Settings > Access Schedule

User Access Control

Restrict network access to specific users.

Menu Location: More Settings > 2.4 or 5GHz Wi-Fi Settings > User Access

Wireless Coverage Control

Web Menu (Left Side)

If you are unfamiliar or want more information on how to enable BoostBand™ Technology or the security features
on the Range Extender, please visit the website: http://support.ampedwireless.com/b1200ex

Adjust the distance of your wireless network.

Menu Location: More Settings > 2.4 or 5GHz Wi-Fi Settings > Wireless Coverage

Setting the Range Extender’s System Clock

In order for your Access Schedules and logs to perform using
the correct time stamps and schedules, you will need to set your
System Clock. To do so, go under Management access the

System Clock tab to sync the System Clock with your computer's

time or to sync with the Internet.

Setting a Login and Password for the Web Menu

This login/password is NOT the wireless security key used to connect to your wireless network.

For added security, you may want to set a login and password
to access the Web Menu. To do this, go to More Settings >

Management > Password on the left side of the web menu.

If you forget your login/password, you will need to reset the Range
Extender back to default settings in order to access the web menu again.
To reset the Extender, hold the Reset button on the Range Extender for 10 seconds.

Tips: Power Outages, Rebooting Routers & Channel Changes

Wireless routers operate on specific wireless channels to avoid interference with neighboring networks. Some
wireless routers are set to automatically scan for the best wireless channel. A power outage or a simple reboot may
cause your home wireless router to change its wireless channel, causing the Range Extender to disconnect from
your home network. After a minute or two the Range Extender will automatically reconnect to your Home
Network with the new settings. However, if for whatever reason it does not, simply log onto the Range Extender’s
web menu by opening your web browser and accessing http://setup.ampedwireless.com. If the page does not load,
try resetting the Range Extender by holding down the Reset button for ten seconds. After the Range Extender has
rebooted, open your web browser and try again.

When the web menu appears, run through the Wizard again to reconfigure the connection to your Home Network.
To prevent the channel changing issue from occurring in the future, you may log onto your router’s web menu and set
the wireless channel from Automatic to a static channel number. You will need to reconfigure the Range Extender
with the new channel. If you are not sure how to access your router’s web menu, contact the support department for
the brand of your wireless router.

Autoloading Web Menu

When the Range Extender loses its connection with your Home Network, the Web Menu will automatically load on
your web browser. All web address entries will be redirected to the Wizard of the Range Extender. This feature is
meant for you to easily reconfigure your Range Extender in the event of a disconnection. This feature may be disabled
in the IP Settings menu of the web menu. The feature is titled: Auto-DNS.

Additional Range Extender Features

Wired Port

WPS /
Reset Button

Wi-Fi Protected Setup (One-Touch Setup or Push Button Configuration)

f your wireless adapter has WPS one-touch setup you can use it when connecting to the Range

• I

Extender. Press the WPS/Reset button on the Range Extender once, do not hold it down. The WPS
LED will begin to blink. As it blinks, push the WPS button on your wireless adapter or enable WPS with
the provided software for your wireless adapter.

Reset the Range Extender to Default Settings

There are two options to reset the Range Extender back to factory default settings:

Access the Reset button through the web menu on the left side under More Settings > Management >

1

Save/Reload Settings. Select the Reset Settings to Default.

2

Access the physical WPS/Reset button on the Range Extender:
Hold down the Reset button for at least ten (10) seconds. Release when the power LED begins to blink.

Troubleshooting Tips

PROBLEM:

SOLUTIONS:

PROBLEM:

SOLUTIONS:

PROBLEM:

SOLUTIONS:

I entered http://setup.ampedwireless.com and it failed to open the Web Menu.

a. Make sure your computer is connected to the Range Extender’s Wi-Fi network: "Amped_B1200EX_2.4" or
"Amped_B1200EX_5.0".
b. Try to use a different web browser. We recommend the Google Chrome web browser.
c. Try to open your web browser to the default IP address by putting this number into your web browser instead:

192.168.1.240
d. Power off (unplug) the Range Extender and power it back on. Try again.
e. Reset your Range Extender to default settings by holding the Reset Button (located on the front panel) for
ten (10) seconds and try again.
f. If steps (a) through (e) fail, disconnect your PC from all Wi-Fi networks. Attach an Ethernet cable between
the Range Extender and your PC. Try to access http://setup.ampedwireless.com again.

My Range Extender was working fine previously, but now I can no longer access the Internet through it.

a. The connection to your Home Network may have been dropped or the router settings may have changed.
Changes to the router could be a result of several events, such as a power outage. When this occurs, connect
to the Range Extender and access the setup menu using the web address: http://setup.ampedwireless.com

Run the Wizard to reconnect the Range Extender to your network.

b. Using the setup menu (setup.ampedwireless.com) check to see that the signal strength between the Range

Extender and your Home Network is above 70%. The Range Extender may be too far from your router and not
maintaining a signal strength above 70%. Check the signal strength between the router and the Range
Extender through the web menu (left side): More Settings > Management > Device Status. The Signal Strength
readout will be under the Home Wireless Network Settings section. This Signal Strength must be above 70%.
If it is below, move the Range Extender closer to your router, or reposition the Range Extender.

I cannot find my Home Network when scanning for wireless networks in the web menu Scan page.

a. The Range Extender may be out of range. Move the Range Extender closer towards the wireless router and
try the Setup Wizard again from the web menu.
b. Make sure that your Home Network’s wireless SSID is broadcasting and not hidden. Hidden SSIDs will require
that you manually enter the SSID into the Wireless Settings > Home Network menu.

If you continue to have issues setting up the Range Extender, give us a call — we’re here to help: 888-573-8820

Visit our website for more support information and answers to frequently asked questions: www.ampedwireless.com/support

Amped Wireless
A Division of Newo Corporation
Copyright © 2017 Amped Wireless / Newo Corporation. All rights reserved.
Amped Wireless, Newo Corporation, Amped Wireless Logo are registered trademarks or trademarks of Newo Corporation.