Page 1
pressure
»
Pressure ranges
Up to 1,000 bar / 14,500 psi
Also vacuum and absolute ranges
»
High accuracy
Down to +/- 0,020% F.S., full temperature
compensation 0 to 50°C
»
Large color display
High resolution TFT color display, great over
view and easy to read
»
Measuring
Measure pressure, voltage and current, and
supplies 24VDC as source for transmitters
Documenting Pressure Calibrator
DPC-501
»
Pressure units
15 different pressure units available, one
additional pressure unit can be defined
»
Selectable language user-interface
Choose between English, German, Italian,
French and Spanish
»
Easy pressure switch test
Automatically records opening and
closing point values on the display
»
External reference sensors
10 reference sensors of different pressure
ranges can be used with the same DPC-501
calibrator
»
Documentation made easy
JOFRACAL calibration software makes
documentation easy
The DPC-501 is a user-friendly, accurate and compact solution for pressure comparison calibrations. The electronic pressure calibrator DPC-501
is used for high-precision calibration of pressure instruments, e.g. pressure gauges, pressure transmitter, digital manometer, pressure switches,
overpressure protection valves, etc.
The DPC-501 measures pressure, voltage and current and supplies
24 VDC as source for transmitters. Calibration procedures can be predefined and used for calibrations on site. The DPC-501 is featured with
USB and RS232 interfaces and is powered by a Lithium-Ion battery
(rechargeable without memory-effect).
The built-in reference sensor is changeable, whereby several pressure
ranges can be covered with one DPC-501 unit. All standard pressure
ranges between vacuum and 1000 bar (14,500 psi) are available as well
as vacuum and absolute pressure ranges.
In “measuring” operation, the DPC-501 displays simultaneous:
ISO 9001 Manufacturer
Specification Sheet
SS-DPC-501
• Reference pressure
• Output of unit under test
• Deviation (in selected pressure unit)
• Deviation (in % of full scale or of reading of unit under test)
This means that it is very easy to check if the unit under test is within it’s
specified accuracy class.
Page 2
Display
High resolution TFT
color display great
overview and easy to
read
Setup - menu
Set-up menu for
choosing measuring, calibration
or switch-test
operation mode.
Selectable userinterface in 5 different languages
Switch test
Perform semi-automatic
pressure switch tests.
Check and adjust the
switch point of pressure
switches. Hysteresis is
calculated and displayed
on the screen
Calibration
Predefine calibration procedures and
work with them.
Upload calibration
data to a PC using
JOFRACAL calibration software
Enter
Confirms the
numeric input
Clear
Deletes the
numeric input
1 step back
Measuring
Measure pressure
and calibrate without
documentation
Pressure connections
Pressure ranges to 1000 bar
(14,500 psi), vacuum and absolute ranges
2 www.jofra.com Documenting Pressure Calibrator • DPC-501
Page 3
JOFRACAL CALIBRATION SOFTWARE
JOFRACAL calibration software ensures easy calibration
of RTD´s, thermocouples, transmitters, thermoswitches,
pressure gauges and pressure switches. JOFRACAL can
be used with all JOFRA calibration instruments. When
used with ASM-800 signal multi scanner, JOFRACAL can
perform a simultaneous semi automatic calibration on up
to 24 pressure and/or temperature devices under test in
any combination.
JOFRACAL software controls the complete calibration
procedure, stores the results and provides a calibration
audit trail through hard-copy certificates. All calibration
data are stored for each sensor to monitor drift and optimise recalibration intervals. A scheduler feature allows
planning of future calibrations.
Power supply 24 VDC
for pressure transmitters
(activated via menu)
Connection cable for
DPC-J reference sensors
Measuring Input
(sockets 4 mm female)
Voltage
Measuring Input
(sockets 4 mm female)
Current and Switch-test
Socket for battery
charger (charging starts
automatically when
charger is connected
USB and RS232 interface for communication with a PC
www.jofra.com 3DPC-501 • Documenting Pressure Calibrator
Page 4
FUNCTIONAL SPECIFICATIONS
Pressure range
The DPC-501 does all it´s reference measurements via the
DPC-J reference sensors. It is therefore always delivered
with one user-specified DPC-J reference sensor.
Pressure accuracy
Pressure ranges from 2.5 to 250 bar (36 to 3,600 psi) .........
...................................................................... ±0.020% F.S.*)
Both ranges included
Other pressure ranges ................................. ±0.025% F.S.*)
F.S. (full scale) is the numerical value of the pressure range or compound
range. The accuracy includes non-linearity, hysteresis, repeatability and
temperature effect 0 to 50°C / 32 to 122°F and one year typical drift.
Temperature compensation
Full temperature compensation ...... 0 to 50°C / 32 to 122°F
Engineering units (built-in)
User selectable ........................................................ 15 units
(bar, mbar, hPa, psi, inHg, cmHg, MPa, kPa, Pa, mH20, cmH20, mmH20, kg/
, inH20, mmHg and 1 user-defined
cm
2
Resolution
.............. adjustable, max. six digits + prefix + decimal point
Input / output
Measurement voltage ............................ 0-10 V, 0-5 V, 0-1 V
Resolution ....................display x 0,1 mV, accuracy ±0.5 mV
Measurement current .............................. 0-20 mA, 4-20 mA
Resolution ........................ display x 1 μA, accuracy ±1.6 μA
Voltage supply ................. 24 VDC min. 20 mA, max. 50 mA
........................................................................ tolerance ±1V
Graphic display
Display type .......................................................... Color TFT
Display resolution ................ up to 6 digits, user selectable
Storage capacity
................................16 test devices each with 22 test points
Power supply
Charging plug 9V/450 mA ±50 mA with metal protection cap
Battery ...... Lithium-Ion with intelligent charging electronics
Battery charger .........230 VAC 50/60 Hz (other on request)
Battery operational time ............................................8 hours
Low battery indicator .....................................icon on display
Protocol ......................................ASCll command language
Media compatibility ........All wetted parts are stainless steel
Communication interface
USB .............................................. with metal protection cap
RS232 .......................................... with metal protection cap
Serial ....................... 4800, 9600 or 11200 Baud, adjustable
Connectors .................................................. Binder type 464
Measurement plugs
4 mm safety plugs for ....... current measurement 0/4-20 mA
voltage measurement 0-1/5/10 V, pressure switch
Transmitter supply ............................................24 V / 50 mA
Instrument dimensions
Calibrator W x H x D ................................... 12.5 x 21 x 8 cm
Weight ............................................................ approx. 1.1 kg
Pressure connection
....................................................................... 1/2” BSP male
Operation conditions
0°C to 50°C ................................... max. 80% r.h. non-cond.
During battery charging......................................... 0 to 45°C
Storage:
-20°C to 60°C ..................... max. 80% r.h. non-condensing
ACCESSORIES
Complete aluminium carrying case
The DPC-501 is available as a calibrator alone or in one of
six test-ready systems that are complete and equipped to
meet all pressure calibration needs.
The complete ready-to-use system is delivered in a practical aluminium carrying case with space for the DPC-501,
up to five reference sensors, set of cables, battery charger, pump, fittings etc.
4 www.jofra.com Documenting Pressure Calibrator • DPC-501
Page 5
DPC-J PRESSURE RANGES
Absolute sensors
Pressure range
bar
0 to 0.4 bar 0 to 6 psi absolute DPCJA104
0 to 0.6 bar 0 to 9 psi absolute DPCJA108
0 to 1 bar 0 to 14.5 psi absolute DPCJA112
0 to 1.6 bar 0 to 32 psi absolute DPCJA116
0 to 2.5 bar 0 to 36 psi absolute DPCJA120
0 to 4 bar 0 to 58 psi absolute DPCJA124
0 to 6 bar 0 to 87 psi absolute DPCJA128
0 to 10 bar 0 to 145 psi absolute DPCJA132
0 to 16 bar 0 to 230 psi absolute DPCJA136
Compound sensors
Pressure range
bar
± 0.25 bar ± 3.6 psi compound DPCJC204
± 0.4 bar ± 6 psi compound DPCJC208
± 0.6 bar ± 9 psi compound DPCJC212
-1 to 1.5 bar -14.5 to 22 psi compound DPCJC216
-1 to 3 bar -14.5 to 43 psi compound DPCJC220
-1 to 5 bar -14.5 to 72 psi compound DPCJC224
-1 to 9 bar -14.5 to 130 psi compound DPCJC228
-1 to 15 bar -14.5 to 220 psi compound DPCJC232
-1 to 20 bar -14.5 to 290 psi compound
-1 to 24 bar -14.5 to 350 psi compound DPCJC236
-1 to 39 bar -14.5 to 560 psi compound DPCJC240
Pressure range
psi
Pressure range
psi
Type Part number
Type Part number
DPCJ234
DPC-J REFERENCE SENSORS
The DPC-J series are high precision reference sensors
with accuracies to ± 0,020% FS (0 to 50°C including nonlinearity, hystereses and repeatability). The DPC-J reference sensors are compatible with the DPC-501 calibrator.
The units are available in a series of ranges, units, and
pressure references, from vacuum to absolute pressure,
offering a lot of opportunities to the need of any pressure
calibration.
The reference sensors are engineered for in-plant, field, or
laboratory use. They are ready-to-use with the DPC-501
pressure calibrator as the protocol allows for immediate
recognition and use of the module once it is plugged into
the calibrator. Digital signal compensation and build in
microprocessor ensures minimal drift over time in the temperature range from 0 to 50°C.
Up to 10 DPC-J sensors can be allocated to each DPC-
501. When combined with the DPC-501 calibrator and
pump systems these reference sensors make for a powerful arsenal of calibration tools.
Weight: .........................................................................300 g
Wetted parts .................................... stainless steel, welded
Gauge sensors
Pressure range
bar
0 to 0.25 bar 0 to 3.6 psi gauge DPCJG304
0 to 0.4 bar 0 to 6 psi gauge DPCJG308
0 to 0.6 bar 0 to 9 psi gauge DPCJG312
0 to 1 bar 0 to 15 psi gauge DPCJG316
0 to 1.6 bar 0 to 32 psi gauge DPCJG320
0 to 2.5 bar 0 to 36 psi gauge DPCJG324
0 to 4 bar 0 to 58 psi gauge DPCJG328
0 to 6 bar 0 to 87 psi gauge DPCJG332
0 to 10 bar 0 to 145 psi gauge DPCJG336
0 to 16 bar 0 to 230 psi gauge DPCJG340
0 to 25 bar 0 to 360 psi gauge DPCJG344
0 to 40 bar 0 to 580 psi gauge DPCJG348
0 to 60 bar 0 to 870 psi gauge DPCJG352
0 to 100 bar 0 to 1,450 psi gauge DPCJG356
0 to 160 bar 0 to 2,300 psi gauge DPCJG360
0 to 250 bar 0 to 3,600 psi gauge DPCJG364
0 to 400 bar 0 to 5,800 psi gauge DPCJG368
0 to 600 bar 0 to 8,700 psi gauge DPCJG372
0 to 1000 bar 0 to 14,500 psi gauge DPCJG376
Pressure range
psi
Type Part number
Vacuum sensors (bar)
Pressure range
bar
-0.4 to 0 bar -6 to 0 psi vacuum DPCJV404
-0.6 to 0 bar -9 to 0 psi vacuum DPCJV408
-1 to 0 bar -14.5 to 0 psi vacuum DPCJV412
Pressure range
psi
Type Part number
DPC-J STANDARD DELIVERY
• DPC-J reference sensors
• Communication cable to DPC-501
• Traceable calibration certificate
DPC-J ORDERING INFORMATION
Order No. Description
Module
DPCJ Documenting reference sensor
Reference sensor
XXXX Last four digits of DPC-J reference sensor
part number
Certificate
F Traceable calibration certificate (standard)
H Accredited calibration certificate
DPCJC240F Sample order number
DPC-J reference sensor -1 to 39 bar with
standard accessories and traceable
calibration certificate
www.jofra.com 5DPC-501 • Documenting Pressure Calibrator
Page 6
DPC-501
System A
• 0 to 2 bar (0 to 30 psi)
• 0 to 40 bar (0 to 580 psi)
This system includes the DPC-501 calibrator to ge ther with
one of the following pneumatic hand pumps: T-960 or
T-970, depending on the chosen pressure range. System
A is an easy-to-use, single-hand-operated calibration
system. No need for a flat surface to operate the system just hold it in your hand.
System A comes in an aluminium carrying case with
cutouts for fittings, hose and the complete assembled
calibration unit - no time is required to assemble the unit
every time you need it. The calibrator can at any time be
used separately for other pressure test tasks.
A special quick connector between the pump and the
calibrator makes it possible to seperate the system in seconds and to swivel the calibrator for easy viewing.
Included with System A delivery
•Standard delivery (see page 12)
•Hand pump T-960 or T-970
•3/8” BSP female adapter with 1/4” BSP and NPT female
terminations
•0.6 m / 24 in hose with 1/4” BSP and NPT female
terminations
•Quick connector between pump and calibrator
•One roll of Teflon tape
•Extension cable 2 m between DPC-501 and DPC-J
reference sensor
•Protective carrying case
Accessories
•Service kit for T-960 pump
• Service kit for T-970 pump
• Pressure hose for T-960/970, 0.6 m std.
• Pressure hose for T-960/970, 0.5 m
• Pressure hose for T-960/970, 1.0 m
• Pressure hose for T-960/970, 2.0 m
• Pressure hose for T-960/970, 5.0 m
• Set of BSP female fittings, teflon tape, packings
* Fitting size : 1x1/8”, 1x3/8”, 1x1/2”
• Set of NPT female fittings, teflon tape, packings
* Fitting size : 1x1/8”, 1x1/4”, 1x3/8” 1x1/2”
• Cable for RS232, DPC-501
• Cable for USB, DPC-501
• Set of five pcs of O-rings for DPC-J sensor
• Connecting cable 2 m for DPC-J and DPC-501
• Quick connector set for DPC-501 sys. A/B
T-960 and T-970 pumps for system A
Model T-960 pneumatic pressure pump features an
extended range vernier adjustment for precisely controlling
pump pressure and comfortable pistol grip handle.
Model T-970 pneumatic pressure pump is similar to the T960, but generate pressure up to 40 bar (580 psi).
Pressure range, T-960 ...................... 0 to 2 bar / 0 to 30 psi
Pressure range, T-970 ....................0 to 40 bar / 0 to 580 psi
Type ..................................................................... Pheumatic
Test medium ..................................................................... Air
Operation ..................................................................Scissor
“O”-rings ................................................................... Buna-N
Wetted parts ............................ Aluminium, brass, stainless,
.......................................................steel, nylon, Nylatron GS
Connection to test object ........................ Hose 0.6 m / 24 in
.........................with 1/4” BSP and NPT female terminations
Size .......................... 21.6 x 12.1 x 6.2 cm / 8.5 x 4.8 x 2.4 in
Weight ............................................................. 1.4 kg / 3.0 lb
Ordering information System A
Order No. Description
Pressure calibrator
DPC DPC-501 pressure calibrator
Total number of reference sensors
SX S1/S2/S3/S4/S5 (S2 = Two sensors)
NONE Pump system only (no calibrator)
System
AXX DPC-501 System A (pump T-960)
AHX DPC-501 System A (pump T-970)
Primary reference sensor to be
mounted on the system at delivery
XXXX Last four digits of DPC-J reference
sensor part number found on page 5
(the additional reference sensors
should be stated separately on the
order)
Certificate
F Traceable calibration certificate (std.)
H Accredited calibration certificate
DPCS2AXXG320F Sample order number
JOFRA DPC-501 calibrator in pressure System AXX with
pneumatic pressure hand pump, optional primary reference sensor 0 to 1.6 bar and one additional reference sensor, both with traceable calibration certificate.
6 www.jofra.com Documenting Pressure Calibrator • DPC-501
Page 7
DPC-501
System B
• -0.91 bar (-13 psi)
to 40 bar (580 psi)
Included with System B delivery
•Standard delivery (see page 12)
•Hand pump T-965/T-975
•3/8” BSP female adapter with 1/4” BSP and NPT female
terminations
•0.6 m / 24 in hose with 1/4” BSP and NPT female
terminations
•One roll of Teflon tape
•Quick connector between pump and calibrator
•Extension cable 2 m between DPC-501 and DPC-J
reference sensor
•Protective carrying case
This system includes the dual function pneumatic hand
pump. With this pump you can calibrate both vacuum
and pressure applications. It takes just a few seconds to
switch between vacuum and pressure, just push one button (valve) on the T-965/T-975 handpump.
System B comes in an aluminium carrying case with cutouts
for fittings, hose and the complete assembled calibration
unit - no time is required to assemble the unit every time you
need it.
The calibrator and the pump are fitted with a special quick
connector that makes it possible to separate the system
in seconds without any tool. This quick connector also
makes it possible to use the assembled system with the
calibrator twisted to any angle.
T-965 and T-975 hand pumps for system B
Model T-965 and T-975 pneumatic pressure pumps feature both vacuum and pressure generation. A quick switch
(valve) makes it easy to switch from vacuum to pressure
measurement. A built-in release valve, volume adjuster for
fine adjustment and dual pressure output enable a safe and
simple operation. The unit offers both metric and imperial
threads on the reference connection and the hose.
Press. range, T-965 ......-0.65 bar (-9.4 psi) to 2 bar (30 psi)
Press. range, T-975 ...-0.91 bar (-13 psi) to 40 bar (580 psi)
Type ..................................................................... Pneumatic
Test medium.....................................................................Air
Operation .................................................................. Scissor
“O”-rings ..................................................................Buna-N
Wetted parts ..........Aluminum, brass, stainless steel, nylon,
Nylatron GS
Connection to test object..................Hose 0.6 m/24 in with
1/4” BSP and NPT female terminations
Size ................................ 21.6x12.1x6.2 cm / 8.5x4.8x2.4 in
Total system weight .....................................5.5 kg / 12.2 lb
Accessories
•Service kit for T-965/T-975 pump
•Pressure hose for T-965/T-975, 0.6 meter std.
•Pressure hose for T-965/T-975, 0.5 meter
•Pressure hose for T-965/T-975, 1.0 meter
•Pressure hose for T-965/T-975, 2.0 meter
•Pressure hose for T-965/T-975, 5.0 meter
•Set of BSP female fittings, teflon tape, packings
* Fitting size : 1x1/8”, 1x3/8”, 1x1/2”
•Set of NPT female fittings, teflon tape, packings
* Fitting size : 1x1/8”, 1x1/4”, 1x3/8” 1x1/2”
•Cable for RS232, DPC-501
•Cable for USB, DPC-501
•Set of 5 pcs of O-rings for DPCJ sensor
•Connecting cable 2 meters for DPCJ and DPC-501
•Quick connector set for DPC-501 system A/B
Ordering information System B
Order No. Description
Pressure calibrator
DPC DPC-501 pressure calibrator
Total number of reference sensors
SX S1/S2/S3/S4/S5 (S2 = Two sensors)
NONE Pump system only (no calibrator)
System
BHX DPC-501 System BHX (pump T-965)
BXX DPC-501 System BXX (pump T-975)
Primary reference sensor to be
mounted on the system at delivery
XXXX Last four digits of DPC-J reference
sensor part number found on page 5
(additional reference sensors should
be stated separately on the order)
Certificate
F Traceable calibration certificate (std)
H Accredited calibration certificate
DPCS2BHXC236F Sample order number
JOFRA DPC-501 calibrator in pressure System BHX kit
with pneumatic combination handpump with optional primary reference sensor -1 to 24 bar and one additional reference sensor, both with traceable calibration certificate.
www.jofra.com 7DPC-501 • Documenting Pressure Calibrator
Page 8
DPC-501
System C
• 0 to 200 bar (3,000 psi)
• 0 to 350 bar (5,000 psi)
Included with System C delivery
•Standard delivery (see page 12)
•Hand pump T-620 or T-620H
•0.6 m (24 in) hose with 1/4” NPT female and 1/4” BSP
terminations
•One roll of teflon tape
•Extension cable 2 m between DPC-501 and DPC-J
reference sensor
•Protective carrying case
This system consists of an DPC-501 calibrator together
with a hydraulic, high pressure hand pump T-620 or
T-620H, which features an oil reservoir to prime the system.
System C is an easy-to-use, single-hand-operated calibration system. No need for a flat surface (table) to operate
the system. The system includes release valve and vernier
valve for fine adjustment to enable safe and simple operation of the pump.
System C comes in an aluminium carrying case with
cutouts for fittings, hose, and the complete assembled
calibration unit - no time is required to assemble the unit
every time you need it. Easy and fast connection between
pump and calibrator makes it easy to use the pressure
calibrator separately for other pressure test tasks.
AMETEK hydraulic hand pump
This easy-to-use hand pump is specially designed for high
pressure applications. The pump has a built-in reservoir,
vent valve and vernier valve for fine adjustment. The pump
has a dual pressure output - one for the test object and
one for the calibrator.
Pressure range, T-620 .................... 0 to 200 bar / 3,000 psi
Pressure range, T-620H ...................0 to 350 bar / 5,000 psi
Type ........................................................................Hydraulic
Test medium ..................................................................... Oil
Reservoir capacity .................................... 200 ml / 0.42 pint
Operation ............................................................. Pistol-grip
“O”-rings ................................................................... Buna-N
Wetted parts .......... Aluminum, brass, stainless steel, Lexan
Connection to test object ........................ Hose 0.6 m / 24 in
.........................with 1/4” BSP and NPT female terminations
Size .......................... 21.6 x 12.1 x 6.2 cm / 8.5 x 4.8 x 2.4 in
Weight ............................................................. 1.4 kg / 3.0 lb
Accessories
•Service kit for T-620 and T-620H pumps
•Pressure hose for T-620/T-620H pumps
•1 m hose with 1/4” BSP female termination
Max. pressure 350 bar (5,000 psi)
•2 m hose with 1/4” BSP female termination
Max. pressure 350 bar (5,000 psi)
• Cable for RS232, DPC-501
•Cable for USB, DPC-501
•Set of five pcs of O-rings for DPC-J sensor
•Connecting cable 2 m for DPC-J and DPC-501
•Oil for T-620 & T-1 pump AAA OIL in 1 gal can
•Oil for T-620 & T-1 pump AAA OIL in 1 qt can
Ordering information System C
Order No. Description
Pressure calibrator
DPC DPC-501 pressure calibrator
Total number of reference sensors
SX S1/S2/S3/S4/S5 (S2 = two sensors)
NONE Pump system only (no calibrator)
System
CXX DPC-501 System C (pump T-620)
CHX DPC-501 System C (pump T-620H)
Primary reference sensor to be
mounted on the system at delivery
XXXX Last four digits of DPC-J reference
sensor part number found on page 5
(additional reference sensors should
be stated separately on the order)
Certificate
F Traceable calibration certificate (std)
H Accredited calibration certificate
DPCS2CXXG360F Sample order number
JOFRA DPC-501 calibrator in pressure System C with
hydraulic pressure hand pump, optional primary reference
sensor 0 to 160 bar and one additional reference sensor,
both with traceable calibration certificate.
8 www.jofra.com Documenting Pressure Calibrator • DPC-501
Page 9
DPC-501
System D
• 0 to 350 bar
(5,000 psi)
Included with System D delivery
•Standard delivery (see page 12)
•Screwpump 65-P016 for hydraulic oil or 65-P017 for water
•One roll of Teflon tape
•10 bonded seals
•6 mm Allen key
•Protective carrying case
This system consists of an DPC-501 calibrator with a rugged, hydraulic, high pressure screw pump.
System D is an easy-to-use calibration system. Place the
pump on a flat surface and turn the handle to generate
pressure. You can adjust the calibrator to fit the best viewing angle. The system includes a manifold for connection
of the test device, a fine adjustment vernier valve (optional)
and a reservoir for extra oil or water (optional).
System D comes in an aluminium carrying case with cutouts for fittings and the complete assembled calibration
unit - no time is required to assemble the unit every time
you need it. Easy and fast connection between pump and
calibrator makes it easy to use the pressure calibrator
separately for other pressure test tasks screw pump.
AMETEK screw pump
The 65-P016 and 65-P017 screw pump are designed for
very easy generation of high pressure. Screw pumps have
a 4-connection mani fold. Fine adjust ment, vernier valve,
liquid reservoir and fittings are optional. The AMETEK
screwpump may be delivered for two different test media:
hydraulic oil or water.
Pressure range .................................350 bar / 0 to 5,000 psi
Type ........................................................................Hydraulic
Test media .............................................. Hydraulic oil, water
Reservoir capability................................... 250 ml / 0.53 pint
Operation ......................................................... Screw pump
“O”-rings ................................................................... Buna-N
Wetted parts ...................... Aluminum, brass, stainless steel
Connections to test objects .................. 4 x 1/4” BSP female
Size ....................... 36.6 x 19.5 x 10.5 cm / 14.4 x 7.7 x 4.1 in
Weight .............................................................3.7 kg / 8.2 lb
Accessories
•Reservoir set with seals, valve and bonded seal
•Valve for oil reservoir
•1 m Pressure hose, (Max. 350 bar / 5,000 psi) *
•2 m Pressure hose, (Max. 350 bar / 5,000 psi) *
•1.5 m Pressure hose, (Max. 700 bar/10,000 psi) *
•5 m Pressure hose, (Max. 700 bar / 10,000 psi) *
•Extension tube, 120 mm (Max. 350 bar / 5.000 psi) *
* 1/4” BSP female to 1/4” BSP male
•Cable for RS232, DPC-501
•Cable for USB, DPC-501
•Set of five pcs of O-rings for DPC-J sensor
•Connecting cable 2 m for DPC-J and DPC-501
•Quick connector set, female 1/4”BSP to 1/4”BSP
Ordering information System D
Order No. Description
Pressure calibrator
DPC DPC-501 pressure calibrator
Total number of reference sensors
SX S1/S2/S3/S4/S5 (S2 = two sensors)
NONE Pump system only (no calibrator)
System
DOX DPC-501 System D (pump 65-P016)
DWX DPC-501 System D (pump 65-P017)
Primary reference sensor to be
mounted on the system at delivery
XXXX Last four digits of DPC-J reference
sensor part number found on page 5
(additional reference sensors should
be stated separately on the order)
Certificate
F Traceable calibration certificate (std)
H Accredited calibration certificate
DPCS2DOXG364F Sample order number
JOFRA DPC-501 calibrator in pressure System D with
hydraulic oil screw pump with optional primary reference
sensor 0 to 250 bar and one additional reference sensor,
both with traceable calibration certificate.
www.jofra.com 9DPC-501 • Documenting Pressure Calibrator
Page 10
DPC-501
System E
• 0 to 700 bar (10,000
psi)
Included with System E delivery
•Standard delivery (see page 12)
•Hydraulic pump 65-P014 for hydraulic oil
•One roll of Teflon tape
•10 bonded seals
•6 mm Allen key
•Protective carrying case
•Vernier valve for fine adjustment
This system consists of an DPC-501 calibrator together
with a rugged, hydraulic, high pressure pump.
System E is an easy-to-use calibration system. The
hydraulic pump makes it very easy to prime the system.
You can adjust the calibrator to fit the best viewing angle.
The system includes a manifold for connection of two test
devices and the fine adjustment vernier valve is standard.
System E comes in an aluminium carrying case with cutouts for fittings and the complete assembled calibration
unit - no time is required to assemble the unit every time
you need it. Easy and fast connection between pump and
calibrator makes it easy to use the pressure calibrator
separately for other pressure test tasks.
AMETEK high pressure hydraulic oil pump
The 65-P014 hydraulic pump is designed for high pressure applications. The pump has a 4-connection output
manifold. Fine adjustment vernier valve and fittings are
optional.
Pressure range ...............................0 to 700 bar / 10,000 psi
Type ........................................................................Hydraulic
Test media ........................................................................ Oil
Reservoir capability........................................ 500 ml / 1 pint
Operation ............................................................ Jack pump
“O”-rings ................................................................... Buna-N
Wetted parts ...................... Aluminum, brass, stainless steel
Connections to test objects .................. 4 x 1/4” BSP female
Size ...................... 36.5 x 20.0 x 14.2 cm / 14.4 x 7.9 x 5,6 in
Weight ..........................................................5.3 kg / 11.6 lbs
Accessories
•Vernier valve for fine adjustment
•1.5 m Pressure hose, (Max. 700 bar/10,000 psi)*
•5 m Pressure hose, (Max. 700 bar / 10,000 psi) *
* 1/4” BSP female to 1/4” BSP male
•Cable for RS232, DPC-501
•Cable for USB, DPC-501
•Set of five pcs of O-rings for DPC-J sensor
•Connecting cable 2 m for DPC-J and DPC-501
•Quick connector set, female 1/4”BSP to 1/4”BSP
Ordering information System E
Order No. Description
Pressure calibrator
DPC DPC-501 pressure calibrator
Total number of reference sensors
SX S1/S2/S3/S4/S5 (S2 = two sensors)
NONE Pump system only (no calibrator)
System
EXX DPC-501 System E (pump 65-P014)
Primary reference sensor to be
mounted on the system at delivery
XXXX Last four digits of DPC-J reference
sensor part number found on page 5
(additional reference sensors should
be stated separately on the order)
Certificate
F Traceable calibration certificate (std)
H Accredited calibration certificate
DPCS2EXXG372F Sample order number
JOFRA DPC-501 calibrator in pressure System E with high
pressure pump for hydraulic oil with optional primary reference sensor 0 to 600 bar and one additional reference
sensor, both with traceable calibration certificate.
10 www.jofra.com Documenting Pressure Calibrator • DPC-501
Page 11
DPC-501
System F
• 0 to 1,000 bar
(14,500 psi)
Included with System F delivery
•Standard delivery (see page 12)
•Type T Hydraulic pump
•Allen key 6 mm
•One roll of teflon tape
•Protective carrying case
System F is an easy-to-use calibration system. The
hydraulic pump makes it very easy to prime the system.
The pump contains 75 in
3
/ 1.23 l of liquid.
The system includes a manifold for connection of two test
devices and the fine adjustment vernier valve is standard.
System F comes in a aluminium carrying case with cutouts for fittings. Easy and fast connection between pump
and calibrator makes it easy to use the pressure calibrator
separately for other pressure test tasks.
AMETEK Type T hydraulic oil or water pump
The Type T pump is designed for high pressure applications up to 15,000 psi (1,000 bar).
The pump and system may be ordered with either oil or a
water/alcohol mixture as the pressure medium. The pump
is constructed of 300 series stainless steel and Monel
allowing for the use of other hydraulic media. There are
three available seal packages for the system: Buna-N,
Viton®, and EPT.
The Type T pump features a dual pressure output manifold, fine adjustment vernier valve, relief valve, and dual
volume control for rapid pressure increase at lower pressures and easier pumping at higher pressures.
Pressure range ............................ 0 to 1,000 bar / 14,500 psi
Type ........................................................................Hydraulic
Test media .............................................. Hydraulic oil, water
Reservoir capacity ...........................................1.23 l / 75 in
Operation ............................................................ Jack pump
“O”-rings .......... Buna-N (standard) or EPT / Viton (optional)
Wetted part ........................................ Stainless steel, Monel
Connections to test objects ......................1/4” and 1/2” BSP
..............terminations; 1/4” and 1/2” PT female terminations
Size .......................... 79.4 x 22.9 x 50.8 cm / 31.3 x 9 x 20 in
Weight .............................................................9.1 kg / 20 lbs
1) Customer must verif y compatibility of seals and pump materials with
pressure medium. Viton is a registered trademark.
1)
Accessories
•Service kit for T pump with Buna N O-rings
•Service kit for T pump with VITON N O-rings
•Service kit for T pump with EPT N O-rings
•1.5 m Pressure hose, (Max. 700 bar/10,000 psi)*
•5 m Pressure hose, (Max. 700 bar / 10,000 psi)*
* 1/4” BSP female to 1/4” BSP male
•Cable for RS232, DPC-501
•Cable for USB, DPC-501
•Set of five pcs of O-rings for DPC-J sensor
•Connecting cable 2 m for DPC-J and DPC-501
•Oil for T-620 & T-1 pump AAA OIL in 1 gal can
•Oil for T-620 & T-1 pump AAA OIL in 1 qt can
Ordering information System F
Order No. Description
Pressure calibrator
DPC DPC-501 pressure calibrator
Total number of reference sensors
SX S1/S2/S3/S4/S5 (S2 = two sensors)
NONE Pump system only (no calibrator)
System
FWB DPC-501 System F (pump T-1)
FWV DPC-501 System F (pump T-1/VITON)
FWE DPC-501 System F (pump T-1/EPT)
FOB DPC-501 System F (pump T-1/OIL)
FOV DPC-501 System F (pump T-1/OIL/VITON)
FOE DPC-501 System F (pump T-1/OIL/EPT)
Primary reference sensor to be
mounted on the system at delivery
3
XXXX Last four digits of DPC-J reference
sensor part number found on page 5
(additional reference sensors should
be stated separately on the order)
Certificate
F Traceable calibration certificate (std)
H Accredited calibration certificate
DPCS2FOEG376F Sample order number
JOFRA DPC-501 calibrator in pressure System F with
Type T pump for oil, with optional primary reference sensor 0 to 1,000 bar and one additional reference sensor,
both with traceable calibration certificate.
www.jofra.com 11DPC-501 • Documenting Pressure Calibrator
Page 12
ORDERING INFORMATION
Order No. Description
Pressure calibrator
DPC DPC-501 Pressure Calibrator
Total number of reference sensors
SX S1/S2/S3/S4/S5 (S2 = two sensors)
Base model number
IND DPC-501 calibrator with standard accessories
Primary reference sensor to be
mounted on the system at delivery
XXXX Last four digits of DPC-J reference
sensor part number found on page 5
(additional reference sensors should
be stated separately on the order)
Certification
F Traceable calibration certificate (std.)
H Accredited calibration certificate
DPCS2INDC240A136F Sample order number
JOFRA DPC-501 with standard accessories, optional primary reference
sensor -1 to 39 bar and one additional reference sensor 0 to 16 bar both
with traceable calibration certificate.
STANDARD DELIVERY
• DPC-501 calibrator
• Traceable calibration certificate
• User manual
• Battery charger
• Test leads: red and black
• Connection cable for RS232
• JOFRACAL calibration software
• DPC-CAL Windows software
• One DPC-J reference sensor (user specified)
A business unit of AMETEK Measurement & Calibration
AMETEK Test & Calibration Instruments
Technologies Division offering the following industry
leading brands for test and calibration instrumentation.
JOFRA Calibration Instruments
Temperature Calibrators
Portable dry-block calibrators, precision thermometers
and liquid baths. Temperature ranges from
-90°C(-130°F) to 1205°C(2200°F). Temperature sensors
for industrial and marine use.
Pressure Calibrators
Convenient electronic systems ranging from -25 mbar to
1000 bar - fully temperature-compensated for problem-
free and accurate field use.
Signal Instruments
Process signal measurement and simulation for easy
control loop calibration and measurement tasks.
M&G Pressure Testers & Pumps
Pneumatic floating-ball or hydraulic piston dead weight
testers with accuracie s to 0.015% of reading. Pressure
generators delivering up to 1,000 bar.
Lloyd Instruments
Materials testing machines and software from Lloyd
Instruments guarantees expert materials testing
solutions. The comprehensive program also covers
Texture Analysers to perform rapid, general food testing
and detailed texture analysis on a diverse range of foods
and cosmetics.
Davenport Polymer Test Equipment
Allows measurement and characterization of moisture-
sensitive PET polymers and polymer density.
Chatillon Force Measurement
The hand held force gauges and motorized testers
have earned their reputation for quality, reliability and
accuracy and they represent the de facto standard for
force measurement.
Newage Testing Instruments
Hardness testers, durometers, optical systems and
software for data acquisition and analysis.
UK
AMETEK Calibration Instruments
Tel +44 (0)1243 833 302
jofra@ametek.co.uk
France
AMETEK S.A.S.
Tel +33 (0)1 30 68 89 40
general.lloyd-instruments@ametek.fr
Germany
AMETEK GmbH
Tel +49 (0)2159 9136 510
info.mct-de@ametek.de
Information in this document is subject to change without notice. ©2012, by AMETEK, Inc., www.ametek.com. All rights reserved.
Denmark
AMETEK Denmark
Tel +45 4816 8000
jofra@ametek.com
USA
AMETEK Mansfield & Green
Tel +1 (800) 527 9999
cal.info@ametek.com
India
AMETEK Instruments India Pvt Ltd.
Tel +91 22 2836 4750
jofra@ametek.com
12 www.jofra.com
www.jofra.com
Singapore
AMETEK Singapore Pte Ltd
Tel +65 6484 2388
jofra@ametek.com
China
AMETEK Inc. - Shanghai
Tel +86 21 5868 5111
AMETEK Inc. - Beijing
Tel +86 10 8526 2111
AMETEK Inc. - Guangzhou
Tel +86 20 8363 4768
jofra.sales@ametek.com.cn
Pub code SS-DPC-501 Issue 1206
Loading...